ATF22LV10CZ-25PC - 500 Gate, 25ns EE PLD | Microchip
N.º da peça: ATF22LV10CZ-25PC ✗ Fim de vidaATF22LV10CZ-25PC Visão geral
A programmable logic device is a programmable semiconductor that implements combinational or registered logic functions using a structured array of AND and OR terms. The ATF22LV10 series belongs to the simple PLD category, positioned below complex PLDs and FPGAs for compact designs requiring modest gate capacity, straightforward architecture, and a small package footprint.
The ATF22LV10CZ-25PC provides 10 macrocells and approximately 500 gates of logic capacity. Its 25 ns speed grade targets control, interface, decoding, and glue-logic functions where cycle-by-cycle performance is sufficient. Operation from 3.3 V to 5 V allows the same design to operate in modern 3.3 V systems or legacy 5 V equipment. The electrically erasable Flash configuration supports in-circuit reprogramming and eliminates one-time-programmable device constraints.
Its zero-power operating mode reduces consumption when the logic device is inactive, while the manufacturer datasheet specifies a maximum standby current of 25 uA. The ATF22LV10CZ/CQZ family is based on proven electrically erasable Flash technology and is intended for designs requiring deterministic combinational logic, registered outputs, and reconfigurable control paths without the resource overhead of an FPGA.
Typical applications include industrial control and data-acquisition equipment, legacy peripheral expansion, address decoding, programmable timer and counter logic, instrument front panels, embedded system interfaces, and small embedded controllers. The 24-pin PDIP package also supports prototyping and through-hole industrial assemblies where a socketed or hand-inserted device is convenient.
When designing around this PLD, verify the required output timing against the 25 ns speed grade and confirm that the board supplies a voltage within the 3.3 V to 5 V operating range. Because the configuration memory is Flash-based, the same fitted device can be rewritten, although programming procedure, logic equations, and state behavior still require careful verification.
This page organizes the device architecture, pin-package constraints, verified alternatives, and practical engineering considerations into one engineering reference. It also distinguishes true same-footprint options from surface-mount variants that require PCB footprint changes before they can be considered drop-in replacements.
Alternativas drop-in para ATF22LV10CZ-25PC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATF22LV10CZ-25PC (mesmo formato e footprint) — diferindo em Device Type, Supply Voltage Range, Package Type, Temperature Grade, Mounting Type.
ATF22LV10CZ-25PI
✅ Drop-InConsulte o preço
Ver ficha técnica →ATF22LV10C-15PC
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATF22LV10CQZ-30PC
✅ Drop-InConsulte o preço
Ver ficha técnica →ATF22V10C-15PI
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →ATF22V10C-25PI
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATF22LV10CZ-25PC Classificações máximas e características elétricas
| Device Type | Simple Programmable Logic Device (SPLD), electrically erasable |
| Architecture | 22V10 |
| Logic Capacity | 500 gates |
| Macrocells | 10 macrocells |
| Propagation Delay | 25 ns |
| Frequência máxima de clock | 40 MHz |
| Supply Voltage Range | 3.3 V to 5 V |
| Low-Voltage Supply | 3.3 V |
| High-Voltage Supply | 5 V |
| Configuration Technology | Electrically erasable Flash memory |
| Process Technology | CMOS |
| Standby Current | 25 uA maximum |
| Encapsulamento | 24-pin PDIP |
| Package Type | DIP-24 through-hole |
| Total Pin Count | 24 pins |
| Product Lifecycle | Obsolete |
Guia de Configuração de Pinos do ATF22LV10CZ-25PC dip-24 through-hole
Configuração de pinos para ATF22LV10CZ-25PC (pacote dip-24 through-hole). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para ATF22LV10CZ-25PC.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ATF22LV10CZ-25PC é adequado para 6 aplicaçãos: Industrial Control and Data-Acquisition Logic, Address Decoding and Peripheral Interface Control, Programmable Timer and Counter Logic, Legacy Instrument Front-Panel Control, Embedded System Glue Logic, Small Embedded Controller Platform.
Industrial Control and Data-Acquisition Logic
The ATF22LV10CZ-25PC suits compact control panels where a small number of registered and combinational functions must be coordinated with external counters, relays, and converters. Its 10 macrocells and 500-gate capacity are enough for sequencing, status decoding, and interlock logic without an FPGA. The 25 ns speed grade fits moderate control paths, while 3.3 V to 5 V operation allows interface to legacy 5 V instrumentation. Verify timing against the slowest external device because the PLD does not add margin by itself.
Recomendado
Address Decoding and Peripheral Interface Control
The ATF22LV10CZ-25PC is appropriate for decoding address, interrupt, or enable signals in a peripheral subsystem because its 10 macrocells can implement compact Boolean equations with registered outputs. The 25 ns propagation delay provides predictable combinational settling for moderate bus-clock rates, and the electrically erasable Flash configuration allows firmware updates or board revisions without replacing the device. When replacing a socketed legacy part, match the 24-pin PDIP outline and verify I/O voltage limits against the connected bus.
Recomendado
Programmable Timer and Counter Logic
A compact timer, pulse conditioner, or event counter can use the ATF22LV10CZ-25PC to combine flip-flop, gating, and output decoding functions in one reprogrammable device. Its 500-gate capacity and 10 macrocells are well matched to small timing-state machines that do not require a processor. The 25 ns grade defines the combinational path available inside the PLD, while external crystal accuracy and counter resolution determine overall timer precision. Confirm maximum clock frequency and setup requirements in the datasheet timing tables.
Recomendado
Legacy Instrument Front-Panel Control
The ATF22LV10CZ-25PC fits legacy test and measurement instruments that need switch decoding, lamp control, mode sequencing, and status logic while retaining a socketed 24-pin PDIP footprint. Its 3.3 V to 5 V operating range supports mixed-generation instrument boards, and Flash configuration simplifies field updates for identical hardware variants. The through-hole package remains convenient for repair and prototype assemblies. Validate input thresholds and output drive capability against the specific instrument schematic before installation.
Recomendado
Embedded System Glue Logic
The ATF22LV10CZ-25PC can implement reset qualification, power-sequence gating, watchdog logic, and peripheral mode decoding between a microcontroller and discrete hardware. Ten macrocells are sufficient for these fixed-interface tasks and eliminate several separate gate packages. The reprogrammable Flash architecture makes board-level logic revisions easier, but the device remains a dedicated PLD rather than a general microcontroller. Check supply sequencing, unused-pin treatment, and I/O direction constraints in the manufacturer documentation.
Recomendado
Small Embedded Controller Platform
For specialized controllers that rely on a fixed Boolean architecture, the ATF22LV10CZ-25PC can execute control equations and registered sequences while an external microcontroller handles higher-level communication. The 25 ns part operates from 3.3 V to 5 V and offers a maximum 40 MHz operating frequency, allowing it to support moderate digital control loops without a large FPGA. Flash-based configuration supports field updates, while the 24-pin PDIP package simplifies legacy through-hole assembly. Verify that the required equations fit the 10 available macrocells.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATF22LV10CZ-25PC — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATF22LV10CZ-25PI | ATF22LV10C-15PC | ATF22LV10CQZ-30PC | ATF22V10C-15PI | ATF22V10C-25PI |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 24-PDIP | 24-PDIP - same | 24-PDIP - same | 24-PDIP - same | 24-PDIP - same | 24-PDIP - same |
| Device Type | 22V10 EE PLD | 22V10 EE PLD | 22V10 EE PLD | 22V10 EE PLD | 22V10 EE PLD | 22V10 EE PLD |
| Propagation Delay | 25 ns | 25 ns | 15 ns | 30 ns | 15 ns | 25 ns |
| Configuration Memory | Electrically erasable Flash | Electrically erasable Flash | Electrically erasable Flash | Electrically erasable Flash | Electrically erasable Flash | Electrically erasable Flash |
| Temperature Grade | Commercial - PC suffix | Industrial - PI suffix | Commercial - PC suffix | Commercial - PC suffix | Industrial - PI suffix | Industrial - PI suffix |
Principais diferenciais
- Closest same-speed 24-pin PDIP replacement with a wider temperature-grade option (vs ATF22LV10CZ-25PI)
- Adds timing margin without changing the through-hole package class (vs ATF22LV10C-15PC)
- Matches the original architecture while covering a slower clock-design boundary (vs ATF22LV10CQZ-30PC)
- Broader 22V10 speed family with the same through-hole architecture (vs ATF22V10C-25PI)
Notas de projeto
Do not treat every 24-pin PLD as interchangeable. ATF22LV10CZ-25SC and ATF22LV10CZ-25SI are 24-SOIC devices, so their land patterns, lead geometry, and PCB routing differ from the 24-PDIP ATF22LV10CZ-25PC. Use only the alternatives identified as 24-PDIP for a board-level replacement, and confirm the pin-description table and supply pins because a standard DIP outline does not guarantee identical functionality.
Keep the 25 ns timing requirement visible during schematic review rather than treating the PLD as a generic combinational block. Include setup and hold time for registered outputs, and account for the delay of external gates when closing a feedback loop. In older industrial systems with long traces, add isolation or buffering where a ringing edge could cause multiple state transitions. A faster alternative provides timing margin but does not correct incorrect logic equations.
For a replacement board, reproduce the original 24-pin PDIP footprint, hole size, and row spacing rather than adapting to a SOIC package. Confirm that the board is a through-hole design and that the replacement can be oriented consistently with pin 1. Because configuration storage is electrically erasable, validate the programming interface and write-protection sequence in the manufacturer's Flash programming instructions before relying on field updates.
Design the board around the 3.3 V to 5 V operating range and verify every connected I/O source remains within the device's input and output limits. The family specification lists standby current up to 25 uA, but system-level consumption also depends on active logic, output loading, and the supply chosen. Place bypass capacitance close to the supply pins and use the manufacturer's recommended configuration to minimize additional external components.
Informações de conformidade
The device is a legacy 22V10 electrically erasable Flash PLD. Compliance declarations are not stated in the available manufacturer or distributor records, so the individual fields remain unknown. AEC-Q100 is not applicable to this general-purpose PLD.