ATMEGA168V-10AUR - 8-bit AVR MCU 16KB Flash 10MHz | Microchip
N.º da peça: ATMEGA168V-10AUR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.04 | $5,04 |
| 10 | $4.8 | $48,00 |
| 100 | $4.5 | $450,00 |
| 500 | $4.2 | $2.100,00 |
| 1.000 | $3.95 | $3.950,00 |
ATMEGA168V-10AUR Visão geral
An 8-bit AVR microcontroller is a single-chip processor built on the Advanced RISC architecture, combining program Flash, data SRAM, EEPROM, peripherals, and general-purpose I/O on one die. Within the power management and embedded control hierarchy, MCUs like the ATmega168V sit at the node between raw logic ICs and application-specific SoCs, executing user firmware for sensing, control, and communication tasks.
Key features include 133 powerful instructions with mostly single-cycle execution, 23 programmable I/O lines, three flexible timer/counters, an 8-channel 10-bit ADC, and debugWIRE on-chip debugging. The V-grade device supports the extended 1.8V to 5.5V voltage range at up to 10MHz, making it well suited to battery-powered designs.
The AVR core uses a Harvard architecture with 32 general-purpose working registers directly connected to the ALU, allowing two independent registers to be accessed in one instruction executed in a single clock cycle. Read-while-write ISP Flash enables firmware updates in the field without halting execution, while power-saving modes (idle, ADC noise reduction, power-save, power-down, standby) extend battery life.
Typical applications include battery-powered sensor nodes, industrial control panels, consumer appliance interfaces, and low-voltage handheld instruments where the wide supply range and 10MHz performance fit.
Design consideration: the 10MHz maximum frequency derates with supply voltage below 2.7V, so verify clock-versus-VCC operating envelopes in the manufacturer datasheet before selecting a crystal.
This page synthesizes distributor pricing, drop-in alternatives, pinout data, and practical design notes not found in the manufacturer datasheet.
Alternativas drop-in para ATMEGA168V-10AUR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATMEGA168V-10AUR (mesmo formato e footprint) — diferindo em Package, Communication Interfaces, Instructions, Working Registers, Flash Memory.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATMEGA168PV-10AUR
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.19 / unidade
Ver ficha técnica →ATMEGA168A-AUR
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.45 / unidade
Ver ficha técnica →ATMEGA168PB-AUR
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.58 / unidade
Ver ficha técnica →ATMEGA168V-10AI
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$2.65 / unidade
Ver ficha técnica →ATMEGA168-20AUR
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$2.76 / unidade
Ver ficha técnica →ATMEGA88V-10AU
✅ Drop-In✓ Em estoque
$1.58 / unidade
Ver ficha técnica →ATMEGA168V-10AUR Classificações máximas e características elétricas
| Core Architecture | AVR 8-bit RISC |
| Flash Memory | 16 KB (8K x 16) ISP |
| SRAM | 1 KB |
| EEPROM | 512 B |
| Frequência máxima de clock | 10 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V |
| Instructions | 133, most single-cycle |
| General Purpose I/O | 23 programmable I/O lines |
| Working Registers | 32 x 8-bit |
| Timers/Counters | 3 (two 8-bit, one 16-bit) |
| ADC | 8-channel 10-bit |
| Debug Interface | debugWIRE on-chip debugging |
| Encapsulamento | 32-TQFP (7x7 mm) |
| Tipo de montagem | Surface Mount |
| Packaging | Tape & Reel |
| Status do ciclo de vida | Active |
Configuração de pinos do ATMEGA168V-10AUR
| Pino 1 | PD3 (PCINT19/OC2B/INT1) — Port D, bit 3 / pin-change interrupt / Timer2 output compare B / external interrupt 1 |
| Pino 2 | PD4 (PCINT20/XCK/T0) — Port D, bit 4 / pin-change interrupt / USART external clock / Timer0 clock input |
| Pino 3 | GND — Ground |
| Pino 4 | VCC — Digital supply voltage |
| Pino 5 | GND — Ground |
| Pino 6 | VCC — Digital supply voltage |
| Pino 7 | PB6 (PCINT6/XTAL1/TOSC1) — Port B, bit 6 / crystal oscillator input / timer oscillator input |
| Pino 8 | PB7 (PCINT7/XTAL2/TOSC2) — Port B, bit 7 / crystal oscillator output / timer oscillator output |
| Pino 9 | PD5 (PCINT21/OC0B/T1) — Port D, bit 5 / pin-change interrupt / Timer0 output compare B / Timer1 clock input |
| Pino 10 | PD6 (PCINT22/OC0A/AIN0) — Port D, bit 6 / pin-change interrupt / Timer0 output compare A / analog comparator positive input |
| Pino 11 | PD7 (PCINT23/AIN1) — Port D, bit 7 / pin-change interrupt / analog comparator negative input |
| Pino 12 | PB0 (PCINT0/CLKO/ICP1) — Port B, bit 0 / pin-change interrupt / system clock output / Timer1 input capture |
| Pino 13 | PB1 (PCINT1/OC1A) — Port B, bit 1 / pin-change interrupt / Timer1 output compare A |
| Pino 14 | PB2 (PCINT2/SS/OC1B) — Port B, bit 2 / pin-change interrupt / SPI slave select / Timer1 output compare B |
| Pino 15 | PB3 (PCINT3/MOSI/OC2A) — Port B, bit 3 / pin-change interrupt / SPI master output / Timer2 output compare A |
| Pino 16 | PB4 (PCINT4/MISO) — Port B, bit 4 / pin-change interrupt / SPI master input |
| Pino 17 | PB5 (PCINT5/SCK) — Port B, bit 5 / pin-change interrupt / SPI serial clock |
| Pino 18 | AVCC — ADC supply voltage |
| Pino 19 | ADC6 — ADC input channel 6 |
| Pino 20 | AREF — Analog reference voltage for ADC |
| Pino 21 | GND — Ground |
| Pino 22 | ADC7 — ADC input channel 7 |
| Pino 23 | PC0 (PCINT8/ADC0) — Port C, bit 0 / pin-change interrupt / ADC input channel 0 |
| Pino 24 | PC1 (PCINT9/ADC1) — Port C, bit 1 / pin-change interrupt / ADC input channel 1 |
| Pino 25 | PC2 (PCINT10/ADC2) — Port C, bit 2 / pin-change interrupt / ADC input channel 2 |
| Pino 26 | PC3 (PCINT11/ADC3) — Port C, bit 3 / pin-change interrupt / ADC input channel 3 |
| Pino 27 | PC4 (PCINT12/SDA/ADC4) — Port C, bit 4 / pin-change interrupt / TWI data / ADC input channel 4 |
| Pino 28 | PC5 (PCINT13/SCL/ADC5) — Port C, bit 5 / pin-change interrupt / TWI clock / ADC input channel 5 |
| Pino 29 | PC6 (PCINT14/RESET) — Port C, bit 6 / pin-change interrupt / Reset (active low); also debugWIRE interface |
| Pino 30 | PD0 (PCINT16/RXD) — Port D, bit 0 / pin-change interrupt / USART receiver input |
| Pino 31 | PD1 (PCINT17/TXD) — Port D, bit 1 / pin-change interrupt / USART transmitter output |
| Pino 32 | PD2 (PCINT18/INT0) — Port D, bit 2 / pin-change interrupt / external interrupt 0 |
Aplicações típicas
ATMEGA168V-10AUR é adequado para 6 aplicaçãos: Battery-Powered Sensor Nodes, Industrial Control Panels, Consumer Appliance Interfaces, Handheld Low-Voltage Instruments, RC Hobby and Servo Control, Arduino-Compatible Prototyping.
Battery-Powered Sensor Nodes
The ATMEGA168V-10AUR fits battery-powered sensor nodes because its 1.8V to 5.5V supply range matches two-cell alkaline and lithium coin-cell discharge curves, eliminating a regulator stage and its quiescent drain. In these nodes the MCU periodically wakes from power-down mode, samples an external sensor through the 8-channel 10-bit ADC, and transmits results over SPI or TWI before returning to sleep. Unlike fixed-3.3V MCUs, the V-grade continues operating down to 1.8V at 10MHz, extracting the full cell capacity. The trade-off is the 10MHz ceiling, which is ample for periodic sensing but not for heavy signal processing.
Recomendado
Industrial Control Panels
In industrial control panels the ATMEGA168V-10AUR serves as a compact logic controller driving relays, reading switches, and sequencing outputs. Its 23 programmable I/O lines, three timer/counters with PWM, and watchdog timer cover typical panel tasks such as motor start sequencing, lamp indication, and fault latching. The 5.5V maximum allows direct connection to buffered 5V industrial logic levels, while the industrial temperature packaging variant supports panel environments. Because ISP Flash supports read-while-write updates, firmware can be revised in installed panels through a bootloader on the USART without desoldering the device, reducing field service cost.
Recomendado
Consumer Appliance Interfaces
Consumer appliances such as coffee makers, fans, and small heating devices use the ATMEGA168V-10AUR for user-interface control: capacitive or mechanical key scanning, LED or segment display driving, and temperature regulation with the 10-bit ADC reading an NTC sensor. The 16KB Flash accommodates menu logic, display drivers, and control loops, while the 512B EEPROM stores user presets through power cycles. The 10MHz clock is sufficient for scan-and-display workloads at low EMI, an important consideration for appliances near radios. Sleep modes permit compliant standby-power targets when clocked slowly in idle or power-save mode between key presses.
Recomendado
Handheld Low-Voltage Instruments
Handheld measurement instruments benefit from the ATMEGA168V-10AUR's 1.8V operation, which allows direct powering from a single lithium cell with a small boost stage or two cells without regulation. The 8-channel 10-bit ADC digitizes analog front-end outputs, the 16-bit Timer/Counter1 gates frequency measurements, and the USART streams readings to a PC. debugWIRE enables on-chip debugging over the RESET pin during development, reducing prototype iterations. Power-saving modes between measurements extend battery life substantially; an estimated duty cycle of 1 percent active at a few milliamps yields months of runtime from AA cells in typical datalogging instruments.
Recomendado
RC Hobby and Servo Control
The ATMEGA168V-10AUR is widely used in RC hobby electronics for servo timing and receiver tasks because the 16-bit Timer/Counter1 generates precise 1-2ms servo pulses and the hardware USART decodes standard RC receiver frames. The 3.3V-5V operating window matches common LiPo receiver rails through simple regulation, and the 10MHz clock provides resolution adequate for 8-bit servo positioning. ISP Flash with bootloader support lets enthusiasts reflash firmware in the field. Compared to dedicated servo ICs, the MCU adds programmable mixing, failsafe, and telemetry logic in the same footprint, making it a flexible single-chip control solution.
Recomendado
Arduino-Compatible Prototyping
The ATmega168 family is the classic core of early Arduino boards (Arduino NG and Diecimila used ATmega168 variants), so the ATMEGA168V-10AUR drops into Arduino-compatible prototypes using the standard bootloader, AVR-GCC toolchain, and Arduino IDE support. The 16KB Flash minus bootloader space still leaves room for moderate sketches, and the 23 I/O lines, TWI, SPI, and 10-bit ADC mirror the Uno-style peripheral set at the V-grade's 1.8V-5.5V range. For battery-operated prototypes running at 3.3V/8MHz or 1.8V-referenced sensors, the V-grade avoids the undervoltage behavior seen with standard 20MHz parts, ensuring reliable flash writes across the discharge curve.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATMEGA168V-10AUR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATMEGA168PV-10AUR | ATMEGA168A-AUR | ATMEGA168PB-AUR | ATMEGA88V-10AU |
|---|---|---|---|---|---|
| Package | 32-TQFP (7x7 mm) | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same | 32-TQFP (7x7 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 16 KB | 16 KB | 16 KB | 16 KB | 8 KB |
| SRAM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| EEPROM | 512 B | 512 B | 512 B | 1 KB | 512 B |
| Max Clock Frequency | 10 MHz | 10 MHz | 20 MHz | 20 MHz | 10 MHz |
| Supply Voltage Range | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Low-Power Technology | Standard V-grade | picoPower | Standard | Standard (enhanced) | Standard V-grade |
Principais diferenciais
- Lowest-voltage operation in the ATmega168 family (vs ATMEGA168-20AUR)
- Larger program memory than the pin-compatible ATmega88 (vs ATMEGA88V-10AU)
- picoPower successor available in same footprint (vs ATMEGA168PV-10AUR)
Notas de projeto
Verify the clock-versus-VCC operating envelope before finalizing the power architecture. The V-grade permits 1.8V to 5.5V at up to 10MHz, but flash write operations have voltage requirements - below the minimum for programming, EEPROM and Flash writes can corrupt data. If the design writes to EEPROM across the full battery discharge curve, add a brown-out detector (internal BOD fuse setting) or gate writes above a safe threshold, for example 2.7V, in firmware.
Place a 100nF ceramic decoupling capacitor directly across each VCC/GND pin pair (pins 4/3 and 6/5 of the TQFP-32) within 2mm of the pins, plus a bulk 4.7uF-10uF capacitor near the supply entry. Connect AVCC (pin 18) to VCC through an LC filter (10uH + 100nF) when ADC accuracy matters, and tie AREF (pin 20) to ground via 100nF when using the internal reference. Do not route fast digital signals under the crystal traces to PB6/PB7.
The most frequent integration errors are fuse-related: setting a clock fuse for an external crystal that is absent bricks the board into permanent reset. Always program clock fuses with the hardware present and validate via ISP before enabling debugWIRE, since debugWIRE occupies the RESET pin and disables ISP until disabled through the debugger. Also note PC6/RESET is active-low; leaving it floating causes erratic resets - use a 10k pull-up.
Informações de conformidade
RoHS compliance and lead-free status inferred from standard Microchip Tape & Reel commercial-grade product offerings; REACH and halogen-free status not explicitly stated in provided data.