ATSAMD21J18A-AFT - 32-bit Cortex-M0+ MCU, 256KB Flash, 64-TQFP | Microchip
N.º da peça: ATSAMD21J18A-AFT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $4.2 | $4,20 |
| 10 | $3.78 | $37,80 |
| 100 | $3.4 | $340,00 |
| 500 | $3.05 | $1.525,00 |
| 1.000 | $2.71 | $2.710,00 |
ATSAMD21J18A-AFT Visão geral
A microcontroller (MCU) is a single-chip computer containing a CPU core, program and data memory, peripherals, and I/O. The Cortex-M0+ core from ARM is the smallest and most energy-efficient ARM core, optimized for deterministic embedded control and low active power. The SAM D21J family extends this core with rich peripherals including SERCOM, ADC, DAC, and event system, placing the MCU in the broader hierarchy: microcontroller -> embedded processor -> semiconductor device.
Key features of the ATSAMD21J18A-AFT include 6 SERCOM serial communication interfaces (each configurable as UART/SPI/I2C), a 12-bit 1 MSPS ADC with up to 20 channels, a 10-bit DAC, full-speed USB device/host, and a 2-channel DMAC for low-overhead data movement. The device supports sleepwalking peripherals and idle/standby modes that drop quiescent current to single-digit microamps, enabling years of battery life in sensor applications.
The ATSAMD21J18A-AFT is functionally safety-capable (FuSa) and integrates the ARM Cortex-M0+ core with single-cycle multiplier, hardware divide, and a Nested Vectored Interrupt Controller (NVIC). A 32-channel event system allows peripherals to trigger one another without CPU intervention, reducing wake latency and energy. The device also includes a segmented LCD controller variant in the family, but the -J18A part focuses on connectivity-rich general-purpose applications.
Typical applications include home automation gateways, IoT sensor nodes with USB connectivity, industrial metering, low-end consumer HMI, smart thermostats, and wearable fitness devices. The extended -40C to +125C temperature range supports outdoor and industrial enclosures.
Designers should plan PCB layout carefully: place the 0.1 uF decoupling capacitor within 2 mm of each VDD pin, provide a solid ground pour under the device, and route the D+/D- lines as a 90-ohm differential pair with no stubs. The internal voltage regulator requires both a VDDCORE and VDDIO supply pin to be decoupled.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para ATSAMD21J18A-AFT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAMD21J18A-AFT (mesmo formato e footprint) — diferindo em ADC, Core, DAC, USB, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAMD21J18A-AU
✅ Drop-In✓ Em estoque
$2.69 / unidade
Ver ficha técnica →ATSAMD21J18A-AUT
✅ Drop-In✓ Em estoque
$2.63 / unidade
Ver ficha técnica →ATSAMD21J17A-AUT
✅ Drop-In✓ Em estoque
$3.3 / unidade
Ver ficha técnica →ATSAMD21J16B-AU
✅ Drop-In✓ Em estoque
$2.75 / unidade
Ver ficha técnica →ATSAMD21J18A-AFT Classificações máximas e características elétricas
| Core | ARM Cortex-M0+ (32-bit) |
| Family | SAM D21J |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 256 KB |
| SRAM | 32 KB |
| Supply Voltage (VDD) | 1.62 V to 3.63 V |
| Temperatura de operação | -40C to +125C |
| Encapsulamento | 64-pin TQFP (10x10 mm) |
| Tipo de montagem | Surface Mount (SMD/SMT) |
| I/O Pins | Up to 52 |
| SERCOM | 6 (each configurable as UART/SPI/I2C) |
| ADC | 12-bit, up to 20 channels, 1 MSPS |
| DAC | 10-bit, 1 channel |
| USB | Full-speed USB 2.0 device and host |
| DMAC | 12 channels |
| Functional Safety | FuSa-capable |
| Status RoHS | Compliant (Green) |
Configuração de pinos do ATSAMD21J18A-AFT
| Pino 1 | PA00 — General-purpose I/O / XIN32 |
| Pino 2 | PA01 — General-purpose I/O / XOUT32 |
| Pino 3 | PA02 — General-purpose I/O / AIN0 |
| Pino 4 | PA03 — General-purpose I/O / AIN1 / VREFA |
| Pino 5 | PA04 — General-purpose I/O / AIN2 |
| Pino 6 | PA05 — General-purpose I/O / AIN3 |
| Pino 7 | PA06 — General-purpose I/O / AIN4 |
| Pino 8 | PA07 — General-purpose I/O / AIN5 |
| Pino 9 | VDD — Digital supply voltage |
| Pino 10 | GND — Ground |
| Pino 11 | PA08 — General-purpose I/O / NMI / AIN6 |
| Pino 12 | PA09 — General-purpose I/O / AIN7 |
| Pino 13 | PA10 — General-purpose I/O / AIN8 |
| Pino 14 | PA11 — General-purpose I/O / AIN9 |
| Pino 15 | PA12 — General-purpose I/O |
| Pino 16 | PA13 — General-purpose I/O |
| Pino 17 | PA14 — General-purpose I/O |
| Pino 18 | PA15 — General-purpose I/O |
| Pino 19 | PA16 — General-purpose I/O / I2S_SDI0 |
| Pino 20 | PA17 — General-purpose I/O / I2S_SDO0 |
| Pino 21 | PA18 — General-purpose I/O / I2S_FS0 |
| Pino 22 | PA19 — General-purpose I/O / I2S_SCK0 |
| Pino 23 | PA20 — General-purpose I/O |
| Pino 24 | PA21 — General-purpose I/O / AIN10 |
| Pino 25 | PA22 — General-purpose I/O / AIN11 |
| Pino 26 | PA23 — General-purpose I/O |
| Pino 27 | PA24 — General-purpose I/O / USB_DM |
| Pino 28 | PA25 — General-purpose I/O / USB_DP |
| Pino 29 | PA26 — General-purpose I/O |
| Pino 30 | PA27 — General-purpose I/O |
| Pino 31 | PA28 — General-purpose I/O |
| Pino 32 | PA29 — General-purpose I/O |
| Pino 33 | PA30 — General-purpose I/O / SWCLK |
| Pino 34 | PA31 — General-purpose I/O / SWDIO |
| Pino 35 | PB00 — General-purpose I/O |
| Pino 36 | PB01 — General-purpose I/O |
| Pino 37 | PB02 — General-purpose I/O / AIN12 |
| Pino 38 | PB03 — General-purpose I/O / AIN13 |
| Pino 39 | PB04 — General-purpose I/O / AIN14 |
| Pino 40 | PB05 — General-purpose I/O / AIN15 |
| Pino 41 | PB06 — General-purpose I/O |
| Pino 42 | PB07 — General-purpose I/O |
| Pino 43 | PB08 — General-purpose I/O |
| Pino 44 | PB09 — General-purpose I/O |
| Pino 45 | PB10 — General-purpose I/O |
| Pino 46 | PB11 — General-purpose I/O |
| Pino 47 | PB12 — General-purpose I/O |
| Pino 48 | PB13 — General-purpose I/O |
| Pino 49 | PB14 — General-purpose I/O |
| Pino 50 | PB15 — General-purpose I/O |
| Pino 51 | PB16 — General-purpose I/O |
| Pino 52 | PB17 — General-purpose I/O |
| Pino 53 | PB18 — General-purpose I/O |
| Pino 54 | PB19 — General-purpose I/O |
| Pino 55 | PB20 — General-purpose I/O |
| Pino 56 | PB21 — General-purpose I/O |
| Pino 57 | VDDIO — I/O supply voltage |
| Pino 58 | GND — Ground |
| Pino 59 | VDDCORE — Internal core voltage output (1.2V) |
| Pino 60 | GND — Ground |
| Pino 61 | VDDIN — Voltage regulator input |
| Pino 62 | RESETN — Reset input (active low) |
| Pino 63 | VREFP — ADC reference voltage positive |
| Pino 64 | VREFN — ADC reference voltage negative |
Aplicações típicas
ATSAMD21J18A-AFT é adequado para 6 aplicaçãos: Home Automation Gateway, IoT Sensor Node with USB, Industrial Metering, Consumer HMI with Display, Wearable Fitness Device, Smart Agriculture Sensor.
Home Automation Gateway
The ATSAMD21J18A-AFT fits home automation gateways by combining 256 KB Flash for Zigbee/Wi-Fi stack plus application logic with full-speed USB for dongle connectivity. Its six SERCOM ports drive multiple wireless co-processor UARTs simultaneously while the 12-bit ADC reads analog sensors. The 48 MHz Cortex-M0+ executes protocol stacks with deterministic latency, and the -40C to +125C range supports indoor attic installations. Sleepwalking peripherals and standby current under 5 uA keep always-on power budgets low for AC-powered but energy-rated designs.
Recomendado
IoT Sensor Node with USB
The ATSAMD21J18A-AFT is ideal for USB-connected IoT sensor nodes because its on-chip full-speed USB 2.0 device port eliminates external PHY chips. The 256 KB Flash stores application plus USB stack plus sensor drivers, while 32 KB SRAM buffers high-rate ADC samples. The 12-channel DMAC moves data without CPU wake-up, extending battery life. The 1.62-3.63 V supply range supports direct Li-ion or 2xAA battery operation with internal LDO regulation. Six SERCOM connect I2C sensors, SPI displays, and UART debug simultaneously.
Recomendado
Industrial Metering
Industrial metering designs use the ATSAMD21J18A-AFT because its 12-bit 1 MSPS ADC captures fast current/voltage transients while the Cortex-M0+ runs RMS and power-factor calculations in real time. The extended -40C to +125C temperature range handles outdoor cabinet environments, and the 64-pin TQFP package with 52 I/O drives segmented displays, optocouplers, and isolated serial links. The on-chip event system triggers ADC conversions from timer compare matches without CPU latency, ensuring sample-accurate metering across load variations.
Recomendado
Consumer HMI with Display
The ATSAMD21J18A-AFT drives consumer human-machine interfaces such as smart thermostats and appliance front panels using its six SERCOM channels to run SPI TFT displays plus I2C touch controllers plus UART wireless modules. The DAC outputs audio cues while the 32 KB SRAM buffers frame updates. The 256 KB Flash holds a full graphics library plus wireless stack. The 48 MHz Cortex-M0+ delivers responsive UI animations and the extended temperature grade tolerates kitchen or bathroom installations where humidity and heat stress components.
Recomendado
Wearable Fitness Device
Wearable fitness devices leverage the ATSAMD21J18A-AFT low-power standby modes that drop current below 5 uA while retaining RTC and RAM. The 12-bit ADC reads heart-rate and SpO2 photodiode signals, six SERCOM connect BLE modules, IMUs, and flash storage. The 48 MHz core handles Bluetooth Low Energy link-layer encryption while event-system wake-ups minimize active time. The 1.62 V minimum supply supports single-cell Li-ion or coin-cell designs, and the -40C to +125C rating covers skin contact and outdoor exercise conditions.
Recomendado
Smart Agriculture Sensor
The ATSAMD21J18A-AFT supports smart agriculture sensor endpoints with its extended -40C to +125C temperature range for outdoor field installations exposed to direct sun and frost. The 12-bit ADC reads soil moisture, temperature, and pH probes; SERCOM interfaces drive LoRa or Sub-GHz radio modules. Sleepwalking SERCOM and event system allow years of battery life on a single Li-SOCl2 cell. The 256 KB Flash stores sensor fusion algorithms and over-the-air update bootloaders. The 64-pin TQFP package simplifies hand-rework for prototyping.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAMD21J18A-AFT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAMD21J18A-AU | ATSAMD21J18A-AUT | ATSAMD21J17A-AU | ATSAMD21J16B-AU |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (10x10 mm) | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same | 64-pin TQFP (10x10 mm) - same |
| Flash Memory | 256 KB | 256 KB (same) | 256 KB (same) | 128 KB (-50%) | 64 KB (-75%) |
| SRAM | 32 KB | 32 KB (same) | 32 KB (same) | 16 KB (-50%) | 8 KB (-75%) |
| Operating Temperature | -40C to +125C | -40C to +85C | -40C to +125C (same) | -40C to +85C | -40C to +85C |
| CPU Frequency | 48 MHz | 48 MHz (same) | 48 MHz (same) | 48 MHz (same) | 48 MHz (same) |
| USB | Full-speed USB 2.0 | Full-speed USB 2.0 (same) | Full-speed USB 2.0 (same) | Full-speed USB 2.0 (same) | Full-speed USB 2.0 (same) |
| SERCOM | 6 | 6 (same) | 6 (same) | 6 (same) | 6 (same) |
Principais diferenciais
- Extended industrial temperature grade -40C to +125C (vs ATSAMD21J18A-AU)
- Full 256 KB Flash vs reduced variants in same family (vs ATSAMD21J16B-AU)
- Functional Safety (FuSa) capability (vs ATSAMC21J18A)
- Six SERCOM channels vs fewer in smaller packages (vs ATSAMD21E18A-AFT)
Notas de projeto
The ATSAMD21J18A-AFT requires both VDDIN (regulator input) and VDDIO (I/O supply) to be tied together through ferrite beads or directly bridged, with a 1 uF + 0.1 uF decoupling pair within 2 mm of each pin. According to the SAM D21 datasheet, VDDIN is the source for the internal 1.2 V LDO that supplies VDDCORE; bypassing VDDIN with at least 4.7 uF bulk capacitance prevents LDO dropout during ADC bursts. Estimated: a 100 mA peak ADC + core load at 3.3 V implies 330 mW peak dissipation inside the chip.
Route the USB D+ and D- pins (PA24/PA25) as a 90-ohm differential pair with no stubs and no vias within 5 mm of the device. According to the SAM D21 datasheet, the USB full-speed transceiver is integrated and does not require an external PHY, but PCB trace impedance must match the USB 2.0 spec. Place a 10 uF + 0.1 uF cap on VBUS if the design is bus-powered. Maintain a continuous ground reference plane under the pair to control common-mode impedance.
Do not configure the BOOTPROT fuse to lock the device without first programming a valid application - a misconfigured lockbit can brick the part and require a 12V high-voltage programmer to recover. According to Microchip errata documents, early SAM D21 silicon revisions had a known USB suspend behavior requiring a firmware workaround in revision A and B; verify silicon revision via the DSU DID register before production. Always set the NVMCTRL fuse to map the bootloader at 0x00000000 BEFORE enabling protected boot.
Place the 32.768 kHz crystal as close as possible to pins XIN32/XOUT32 (PA00/PA01) with short, symmetric traces and a guard ring tied to analog ground. According to the SAM D21 datasheet, stray capacitance above 5 pF on these pins detunes the crystal load and degrades RTC accuracy below 20 ppm. Estimated: a 4 mm trace plus a 2 pF pad capacitance gives 1.5 pF total stray, well within margin for an external load capacitor of 12.5 pF. Shield the crystal from digital signals crossing nearby.
Informações de conformidade
Green / lead-free / RoHS compliant per Microchip ordering information. Not AEC-Q100 qualified; for automotive designs, look at SAM DA1 family.
