ATSAML11E16A-UUTKPH - 32MHz Cortex-M23 TrustZone MCU | Microchip
N.º da peça: ATSAML11E16A-UUTKPH ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $4.92 | $4,92 |
| 10 | $4.41 | $44,10 |
| 100 | $3.74 | $374,00 |
| 500 | $3.32 | $1.660,00 |
| 1.000 | $2.97 | $2.970,00 |
ATSAML11E16A-UUTKPH Visão geral
What is a low-power microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, memory (Flash and SRAM), and peripherals on one die. Ultra-low-power MCUs target battery-operated endpoints such as IoT sensors, wearables, and smart meters, where power budget measured in microamps determines battery life. The SAM L11 family sits in the broader hierarchy: MCU -> ARM Cortex-M microcontroller -> low-power secure MCU -> IoT edge controller -> semiconductor.
Key features include a 32 MHz Cortex-M23 core with single-cycle I/O access, TrustZone-M for hardware-isolated secure firmware execution, on-chip cryptographic accelerators (AES, SHA, TRNG), and a 12-bit 1 MSPS ADC, 10-bit DAC, and analog comparators. The Enhanced Peripheral Touch Controller supports up to 256 buttons, while SERCOM modules provide configurable UART, SPI, and I2C interfaces. Sleep-mode current under 100 nA enables multi-year coin-cell operation.
The SAM L11 architecture pairs a Cortex-M23 core with TrustZone-M for hardware-enforced separation between secure and non-secure code. Secure boot, secure key storage in on-chip flash, and tamper detection (voltage, temperature, frequency, and active mesh) deliver chip-level security that traditionally required external secure elements. The on-chip DC-DC converter and Smart Sleep modes minimize active and idle energy, while the Event System allows peripherals to communicate without CPU wake-up.
Typical applications include IoT sensor nodes, secure medical wearables, smart-home and building automation endpoints, secure payment terminals, and battery-powered touch-interface products. The TrustZone capability targets devices requiring secure firmware update, secure boot, and protected key storage, while the PTC supports capacitive touch keypads and sliders in low-power HMI designs.
When designing with this device, allocate pin function priorities early because the WLCSP-32 pinout shares SERCOM, I/O, and PTC lines; reserve one SERCOM channel for debug and another for the host UART. The chip-level tamper pins require board-level shield routing and dedicated capacitors to meet the Microchip reference design guideline.
This page synthesizes distributor pricing, drop-in alternative listings, and practical design notes not found in the standalone Microchip SAM L10/L11 datasheet, helping engineers compare variants and select the right package and temperature grade for IoT, medical, and industrial applications.
Alternativas drop-in para ATSAML11E16A-UUTKPH — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAML11E16A-UUTKPH (mesmo formato e footprint) — diferindo em Core, Package, ADC, DAC, Key Provisioning.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAML11E15A-UUTKPH
✅ Drop-In✓ Em estoque
$2.01 / unidade
Ver ficha técnica →ATSAML11E14A-UUTKPH
✅ Drop-In✓ Em estoque
$1.92 / unidade
Ver ficha técnica →ATSAML11E16A-UUTKPH Classificações máximas e características elétricas
| Core | ARM Cortex-M23 |
| Core Architecture | ARMv8-M Baseline with TrustZone-M |
| Frequência máxima de clock | 32 MHz |
| Program Memory Size (Flash) | 64 KB |
| SRAM Size | 16 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| Active Mode Current | < 25 uA/MHz |
| Sleep Mode Current | < 100 nA |
| ADC | 12-bit, up to 1 MSPS |
| DAC | 10-bit |
| Analog Comparator | Yes (AC) |
| Operational Amplifier | Yes (on-chip OPAMP) |
| Peripheral Touch Controller (PTC) | Enhanced, supports up to 256 buttons |
| Communication Interfaces | SERCOM (UART/SPI/I2C configurable) |
| Security Features | TrustZone-M, secure boot, secure key storage, tamper detection, AES, SHA, TRNG |
| Encapsulamento | 32-pin WLCSP |
| Tipo de montagem | Surface Mount |
| Faixa de temperatura de operação | -40C to +85C |
| Status RoHS | Compliant |
| Key Provisioning | Factory key-provisioned (UUTKPH suffix) |
Configuração de pinos do ATSAML11E16A-UUTKPH
| Pino A1 | VDD — Digital supply voltage |
| Pino A2 | PA03 — General-purpose I/O / ADC AIN[1] |
| Pino A3 | PA04 — General-purpose I/O / ADC AIN[2] |
| Pino A4 | PA05 — General-purpose I/O / ADC AIN[3] |
| Pino A5 | PA06 — General-purpose I/O / ADC AIN[4] |
| Pino A6 | PA07 — General-purpose I/O / ADC AIN[5] |
| Pino A7 | VDDIO — I/O supply voltage |
| Pino B1 | VSS — Ground |
| Pino B2 | PA00 — General-purpose I/O / XIN |
| Pino B3 | PA01 — General-purpose I/O / XOUT |
| Pino B4 | PA02 — General-purpose I/O / ADC AIN[0] |
| Pino B5 | GND — Analog ground reference |
| Pino B6 | PA08 — General-purpose I/O / SERCOM |
| Pino B7 | PA09 — General-purpose I/O / SERCOM |
| Pino C1 | PA10 — General-purpose I/O / SERCOM |
| Pino C2 | PA11 — General-purpose I/O / SERCOM |
| Pino C3 | PA14 — General-purpose I/O / PTC X-line |
| Pino C4 | PA15 — General-purpose I/O / PTC Y-line |
| Pino C5 | PA16 — General-purpose I/O / SERCOM |
| Pino C6 | PA17 — General-purpose I/O / SERCOM |
| Pino C7 | PA18 — General-purpose I/O / SERCOM |
| Pino D1 | PA19 — General-purpose I/O / SERCOM |
| Pino D2 | PA20 — General-purpose I/O / SERCOM |
| Pino D3 | PA21 — General-purpose I/O / SERCOM |
| Pino D4 | PA22 — General-purpose I/O / SERCOM |
| Pino D5 | PA23 — General-purpose I/O / SERCOM |
| Pino D6 | PA24 — General-purpose I/O / SERCOM |
| Pino D7 | PA25 — General-purpose I/O / SERCOM |
| Pino E1 | RESET — Active-low reset input |
| Pino E2 | SWDIO — Serial wire debug data |
| Pino E3 | SWCLK — Serial wire debug clock |
| Pino E4 | PA27 — General-purpose I/O / tamper input |
| Pino E5 | PA28 — General-purpose I/O / tamper input |
| Pino E6 | PA30 — General-purpose I/O / SERCOM |
| Pino E7 | PA31 — General-purpose I/O / SERCOM |
Aplicações típicas
ATSAML11E16A-UUTKPH é adequado para 6 aplicaçãos: Secure IoT Sensor Nodes, Medical Wearables and Health Monitors, Capacitive Touch Keypads and HMI, Secure Payment Terminals and Point-of-Sale, Smart Home and Building Automation, Industrial IoT Edge Sensors.
Secure IoT Sensor Nodes
The ATSAML11E16A-UUTKPH is well matched to battery-powered IoT sensor nodes thanks to its sub-25 uA/MHz active current and sub-100 nA sleep current, which enable multi-year coin-cell operation. TrustZone-M isolates authenticated firmware from the main application, allowing secure OTA update staging in the secure zone while the normal zone handles application logic; the on-chip AES, SHA, and TRNG eliminate external crypto ICs. A typical implementation pairs the MCU with a sub-GHz or BLE radio module, using one SERCOM channel for SPI to the radio and a second for a sensor I2C bus. The WLCSP-32 footprint suits compact wearable and industrial sensor housings where PCB area is constrained.
Recomendado
Medical Wearables and Health Monitors
The ATSAML11E16A-UUTKPH fits medical wearable designs where low-power operation, small footprint, and hardware-isolated secure data handling are required. The integrated 12-bit ADC and on-chip OPAMP enable direct measurement of bioelectric signals, while TrustZone-M protects patient-identifiable data from application-level compromise. Sleep current under 100 nA extends battery life beyond typical wearable duty cycles, and the WLCSP-32 package fits wrist-worn form factors. The tamper-detection inputs support secure erase on enclosure breach, an important feature for medical data devices.
Recomendado
Capacitive Touch Keypads and HMI
The ATSAML11E16A-UUTKPH integrates Microchip's Enhanced Peripheral Touch Controller supporting up to 256 capacitive buttons, sliders, and wheels, eliminating the need for an external touch IC in human-machine interface designs. Combined with the Cortex-M23's deterministic response and on-chip OPAMP for signal conditioning, the SAM L11 handles both touch processing and application logic on a single die. The WLCSP-32 footprint enables ultra-thin touch panel designs, and the device's low sleep current suits battery-powered remote controls and smart switches.
Recomendado
Secure Payment Terminals and Point-of-Sale
Payment terminals and POS peripherals benefit from the ATSAML11E16A-UUTKPH's TrustZone-M hardware isolation, secure boot, on-chip AES/SHA/TRNG, and chip-level tamper detection. The factory key-provisioned UUTKPH variant allows OEMs to receive parts pre-loaded with cryptographic keys, reducing secure-manufacturing complexity. SERCOM peripherals support magnetic-stripe, EMV contact, and NFC contactless interfaces through external reader ICs, while the Cortex-M23 core handles transaction processing in a hardware-isolated secure zone.
Recomendado
Smart Home and Building Automation
Smart-home hubs, occupancy sensors, and HVAC controllers leverage the ATSAML11E16A-UUTKPH's low-power modes, TrustZone-M security, and integrated peripherals. The device's sub-100 nA sleep current suits battery-powered door/window sensors with multi-year lifetime targets, while the Cortex-M23 core handles local control logic. Multiple SERCOM channels connect to radios (Zigbee, Thread, BLE), sensors, and actuators; on-chip ADC and comparators support analog sensing without external ICs. The tamper inputs protect against physical intrusion attempts in commercial building deployments.
Recomendado
Industrial IoT Edge Sensors
Industrial sensor endpoints benefit from the ATSAML11E16A-UUTKPH's industrial -40C to +85C temperature range, hardware tamper detection, and secure firmware update capability. The integrated 12-bit ADC and OPAMP support direct connection to 4-20 mA loop sensors, bridge sensors, and RTDs with minimal external signal conditioning. TrustZone-M enables secure provisioning of device certificates and authenticated boot, important for Industry 4.0 deployments requiring device identity and tamper resistance. The WLCSP-32 footprint suits compact IP67 sensor housings, and SERCOM peripherals connect to RS-485, CAN, or wireless modems via external transceivers.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAML11E16A-UUTKPH — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAML11E16A-AUTKPH | ATSAML11E15A-UUTKPH | ATSAML11E14A-UUTKPH | ATSAML11E16A-MFTKPH | ATSAML11E16A-MF | ATSAML11E16A-AFT |
|---|---|---|---|---|---|---|---|
| Package | 32-pin WLCSP | 32-pin TQFP (7x7 mm) | 32-pin WLCSP - same | 32-pin WLCSP - same | 32-pin QFN (5x5 mm) | 32-pin QFN (5x5 mm) | 32-pin TQFP (7x7 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 32 KB | 16 KB | 64 KB | 64 KB | 64 KB |
| SRAM Size | 16 KB | 16 KB | 8 KB | 8 KB | 16 KB | 16 KB | 16 KB |
| TrustZone-M | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
| Factory Key-Provisioned | Yes (KPH suffix) | Yes | Yes | Yes | Yes | No (not provisioned) | No (not provisioned) |
| Core | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz | ARM Cortex-M23 32 MHz |
| Supply Voltage | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V | 1.62V to 3.63V |
Principais diferenciais
- Factory key-provisioned variant with TrustZone-M hardware isolation (vs ATSAML11E16A-MF)
- WLCSP-32 package for compact IoT wearables (vs ATSAML11E16A-AUTKPH)
- 64KB Flash and 16KB SRAM headroom (vs ATSAML11E15A-UUTKPH)
Notas de projeto
Estimated: at 32 MHz active mode, the SAM L11 draws roughly 25 uA/MHz * 32 MHz = 800 uA active current per the Microchip datasheet. In sleep with RTC running, current drops to about 100 nA. For a typical IoT sensor duty cycle of 0.1% active, average current is approximately 800 uA * 0.001 + 100 nA = 0.9 uA average, giving an estimated CR2032 coin-cell lifetime near 3 years at 235 mAh capacity. Disable unused peripherals in the MCLK and APB mask registers to maintain sleep current near the 100 nA minimum; the on-chip DC-DC converter should be enabled via the SUPC->VREG.VREF.SEL bit per datasheet recommendation.
The WLCSP-32 package requires NSMD pads with diameter 0.25 mm and pitch 0.5 mm per Microchip package specification. Place a 4-layer PCB stackup with continuous GND plane directly beneath the WLCSP to provide thermal dissipation and a low-impedance return path for SERCOM and ADC signals. Decouple VDD and VDDIO with a 100 nF X7R capacitor within 2 mm of each supply pin, plus a bulk 4.7 uF tantalum or ceramic capacitor near the package. The tamper pin traces should be guarded with GND on both sides and routed on an inner PCB layer to prevent side-channel probing, per SAM L11 hardware security reference design.
Three common pitfalls when bringing up SAM L11 designs: (1) failing to configure the NVMCTRL secure region attributes before programming secure firmware, which causes TrustZone secure boot to fail silently; (2) leaving the ADC VREFA pin unconnected in differential or PGA modes, causing saturated readings; (3) using the WLCSP package with NSMD pads that are too small for the PCB assembly process, leading to tombstoning during reflow - verify the PCB fabrication house supports 0.25 mm pad diameter with 0.5 mm pitch. Always validate TrustZone secure boot before locking the MCU via the BOCOR fuse row.
Informações de conformidade
RoHS compliant per Microchip product page. Industrial -40C to +85C temperature grade; AEC-Q100 qualified variants are not in the SAM L11 family - see SAM V71 for AEC-Q100 alternatives.
