ATSAML21G16B-MNT - 48MHz ARM Cortex-M0+ MCU, 64KB Flash | Microchip
N.º da peça: ATSAML21G16B-MNT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $4.4374 | $4,44 |
| 10 | $3.95 | $39,50 |
| 100 | $3.42 | $342,00 |
| 500 | $2.98 | $1.490,00 |
| 1.000 | $2.65 | $2.650,00 |
ATSAML21G16B-MNT Visão geral
What is an ARM Cortex-M0+ microcontroller? An ARM Cortex-M0+ microcontroller is a 32-bit RISC processor core designed for embedded systems that need deterministic real-time performance at very low power consumption. The Cortex-M0+ sits at the low-power end of the ARM Cortex-M family, using the Armv6-M architecture and the Thumb-2 instruction set, and integrates a Nested Vectored Interrupt Controller (NVIC) and Wake-up Interrupt Controller (WIC). MCUs based on this core (microcontroller -> RISC processor -> embedded processor -> semiconductor) are widely used in IoT, sensor hubs, wearables, and battery-powered industrial nodes.
Key features of the ATSAML21G16B-MNT include the Cortex-M0+ core at 48 MHz, 64 KB Flash, 8 KB SRAM, multiple low-power modes (Sleep at 200 nA, Standby, Backup, and Off), 14 SERCOM channels (which can be configured as I2C, SPI, or UART), a 12-bit ADC with up to 20 channels, and built-in touch-support peripherals. The 48-pin QFN (7x7 mm) package provides a compact footprint with an exposed thermal pad for improved thermal dissipation in space-constrained designs.
Technically, the SAM L21 family is built on an ultra-low-power process and integrates a sophisticated power management unit (PMU) that selects among active, idle, sleep, standby, backup, and off modes on a per-peripheral basis. The on-chip voltage regulator supports operation from 1.6 V to 3.6 V, and the device includes up to 5 SERCOM, 1 TC, 1 TCC, and various analog peripherals depending on pin count. The -MNT suffix denotes the 48-QFN package operating from -40°C to 85°C industrial range.
Typical applications include IoT sensor nodes, wearable health and fitness devices, smart home sensors, low-power wireless modules, industrial battery-powered meters, and Human-Machine Interface (HMI) control with touch. The combination of 200 nA Sleep current and fast wake-up makes it ideal for systems that spend most of their time in deep sleep and only wake briefly to take measurements.
When designing with the ATSAML21G16B-MNT, ensure that firmware implements proper Sleep mode entry via the ARM Wait-For-Interrupt (WFI) or Wait-For-Event (WFE) instructions, and that unused peripherals are clock-gated. The 48-QFN exposed pad must be soldered to the PCB ground plane for electrical and thermal performance.
This page synthesizes distributor pricing, same-family alternatives, cross-references, and design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para ATSAML21G16B-MNT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com ATSAML21G16B-MNT (mesmo formato e footprint) — diferindo em Package, Active Mode Current, Family, SRAM, Core Architecture.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ATSAML21G17B-MUT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$2.25 / unidade
Ver ficha técnica →ATSAML21G16B-AUT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATSAML21E16B-MUT
✅ Drop-In✓ Em estoque
$2.3 / unidade
Ver ficha técnica →ATSAML21G15B-MUT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ATSAML21J16B-MUT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$2.18 / unidade
Ver ficha técnica →STM32L031G8U6
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ATSAML21G16B-MNT Classificações máximas e características elétricas
| Core | ARM Cortex-M0+ (32-bit) |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 64 KB (64K x 8) |
| SRAM | 8 KB |
| Operating Voltage Range | 1.6 V to 3.6 V |
| Active Mode Current | <35 µA/MHz |
| Sleep Mode Current | 200 nA |
| Faixa de temperatura de operação | -40°C to +85°C |
| Encapsulamento | 48-QFN (7x7 mm) with exposed pad |
| Tipo de montagem | Surface Mount |
| Number of SERCOM Channels | 14 |
| ADC | 12-bit, up to 20 channels |
| Status RoHS | Compliant |
| Lead-Free | Yes |
| Family | SAM L21 |
| Carrier Type | Tape & Reel (per ordering code) |
Configuração de pinos do ATSAML21G16B-MNT
| Pino 1 | VDDIO — Digital I/O supply voltage |
| Pino 2 | PA00 — GPIO / SERCOM / ADC |
| Pino 3 | PA01 — GPIO / SERCOM / ADC |
| Pino 4 | PA02 — GPIO / SERCOM / ADC |
| Pino 5 | PA03 — GPIO / SERCOM / ADC |
| Pino 6 | GND — Ground |
| Pino 7 | PA04 — GPIO / SERCOM / ADC |
| Pino 8 | PA05 — GPIO / SERCOM / ADC |
| Pino 9 | PA06 — GPIO / SERCOM / ADC |
| Pino 10 | PA07 — GPIO / SERCOM / ADC |
| Pino 11 | PA08 — GPIO / SERCOM / ADC |
| Pino 12 | PA09 — GPIO / SERCOM / ADC |
| Pino 13 | PA10 — GPIO / SERCOM / ADC |
| Pino 14 | PA11 — GPIO / SERCOM / ADC |
| Pino 15 | VDD — Core supply voltage |
| Pino 16 | GND — Ground |
| Pino 17 | PA12 — GPIO / SERCOM / ADC |
| Pino 18 | PA13 — GPIO / SERCOM / ADC |
| Pino 19 | PA14 — GPIO / SERCOM |
| Pino 20 | PA15 — GPIO / SERCOM |
| Pino 21 | PA16 — GPIO / SERCOM |
| Pino 22 | PA17 — GPIO / SERCOM |
| Pino 23 | PA18 — GPIO / SERCOM |
| Pino 24 | PA19 — GPIO / SERCOM |
| Pino 25 | PA20 — GPIO / SERCOM |
| Pino 26 | PA21 — GPIO / SERCOM |
| Pino 27 | PA22 — GPIO / SERCOM |
| Pino 28 | PA23 — GPIO / SERCOM |
| Pino 29 | PA24 — GPIO / SERCOM |
| Pino 30 | PA25 — GPIO / SERCOM |
| Pino 31 | PA27 — GPIO |
| Pino 32 | RESET — Reset input (active low) |
| Pino 33 | PA28 — GPIO |
| Pino 34 | PA30 — GPIO |
| Pino 35 | PA31 — GPIO |
| Pino 36 | PB00 — GPIO / SERCOM |
| Pino 37 | PB01 — GPIO / SERCOM |
| Pino 38 | PB02 — GPIO / SERCOM |
| Pino 39 | PB03 — GPIO / SERCOM |
| Pino 40 | PB04 — GPIO / SERCOM |
| Pino 41 | PB05 — GPIO / SERCOM |
| Pino 42 | PB06 — GPIO / SERCOM |
| Pino 43 | PB07 — GPIO / SERCOM |
| Pino 44 | PB08 — GPIO / SERCOM |
| Pino 45 | PB09 — GPIO / SERCOM |
| Pino 46 | PB10 — GPIO / SERCOM |
| Pino 47 | PB11 — GPIO / SERCOM |
| Pino 48 | GND — Ground / exposed pad |
Aplicações típicas
ATSAML21G16B-MNT é adequado para 6 aplicaçãos: Battery-Powered IoT Sensor Nodes, Wearable Health and Fitness Devices, Smart Home Sensor Hubs, Industrial Battery-Powered Meters, Low-Power Wireless Sensor Modules, Touch-Enabled HMI Controls.
Battery-Powered IoT Sensor Nodes
The ATSAML21G16B-MNT's 200 nA Sleep current and <35 µA/MHz Active current make it ideal for IoT sensor nodes that spend most of their life in deep sleep and wake briefly to take measurements. With 64 KB of Flash, designers can run a full LoRaWAN or BLE beacon stack plus application code, while 8 KB of SRAM accommodates modest buffers. The Cortex-M0+ core at 48 MHz executes sensor fusion or edge inference quickly enough to keep wake windows short, preserving battery life. The 1.6-3.6 V supply range allows direct connection to a single Li-ion cell or two AA batteries, and the small 48-QFN (7x7 mm) footprint fits into coin-cell powered PCB designs.
Recomendado
Wearable Health and Fitness Devices
Wearable health monitors demand sub-mA average current consumption to survive on coin cells, and the ATSAML21G16B-MNT delivers with 200 nA Sleep current. The integrated 12-bit ADC with up to 20 channels captures heart-rate, SpO2, and motion sensor data, while 14 SERCOM channels support I2C sensors and SPI displays. The Cortex-M0+ runs at 48 MHz, sufficient for real-time step counting, heart-rate algorithms, and BLE radio coordination. The 7x7 mm QFN enables slim, lightweight wearable form factors.
Recomendado
Smart Home Sensor Hubs
The ATSAML21G16B-MNT powers smart-home sensors for temperature, occupancy, leak detection, and air quality with its low-power Cortex-M0+ core. The 14 SERCOM channels let designers connect multiple I2C/SPI sensors without an external multiplexer, while the 48 MHz performance handles on-device thresholding before reporting to a central hub. The 1.6-3.6 V supply range suits battery, energy-harvesting, or USB-powered installations. The industrial -40 to +85°C operating range handles attics, basements, and outdoor enclosures.
Recomendado
Industrial Battery-Powered Meters
For utility meters and remote industrial sensors, the ATSAML21G16B-MNT provides the long-term reliability and low-power operation required for 10+ year battery life. Sleep current at 200 nA dominates total energy budget, while the Cortex-M0+ executes measurement cycles quickly. The 64 KB Flash supports meter calibration tables, encryption keys, and communication stacks; 8 KB SRAM handles measurement buffers. The industrial temperature grade (-40 to +85°C) and wide supply range (1.6-3.6 V) tolerate harsh meter environments.
Recomendado
Low-Power Wireless Sensor Modules
The ATSAML21G16B-MNT serves as the host MCU in low-power wireless sensor modules pairing with sub-GHz or BLE transceivers. Its 48 MHz core handles radio stack tasks, sensor I/O, and edge processing while the SERCOM channels provide UART/SPI interfaces to popular transceivers. The 200 nA Sleep current keeps quiescent draw negligible when the radio is idle, and the 48-QFN's exposed pad provides thermal margin for higher transmit-duty-cycle applications. The same firmware image scales across the SAM L21 family for SKU consolidation.
Recomendado
Touch-Enabled HMI Controls
The ATSAML21G16B-MNT integrates Microchip's Peripheral Touch Controller (PTC) supporting capacitive touch buttons, sliders, and wheels, making it well suited for white-good, appliance, and industrial HMI panels. The 12-bit ADC supports up to 20 channels for additional sensor inputs, and 14 SERCOM channels handle display drivers or external peripherals. The 64 KB Flash accommodates touch firmware plus graphical UI logic, while the 48-QFN package is compact enough for appliance front panels.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ATSAML21G16B-MNT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ATSAML21G17B-MUT | ATSAML21E16B-MUT | ATSAML21G15B-MUT | STM32L031G8U6 |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | STMicroelectronics |
| Package | 48-QFN (7x7) | 48-QFN (7x7) - same | 48-QFN - same | 48-QFN - same | 48-QFN - same |
| Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 32 MHz |
| Flash Memory | 64 KB | 128 KB | 64 KB | 32 KB | 64 KB |
| SRAM | 8 KB | 16 KB | 8 KB | 4 KB | 8 KB |
| Operating Voltage | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.6 V to 3.6 V | 1.65 V to 3.6 V |
| Operating Temperature | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +85°C | -40°C to +125°C |
Principais diferenciais
- Ultra-low-power Sleep current at 200 nA (vs STM32L031G8U6)
- Higher core frequency than competing Cortex-M0+ parts (vs STM32L031G8U6)
- 14 SERCOM channels for flexible peripheral mapping (vs ATSAML10E16A-MUT)
Notas de projeto
Use the ARM Wait-For-Event (WFE) or Wait-For-Interrupt (WFI) instructions to enter Sleep mode; the SAM L21 PMU will then drop to ~200 nA while retaining SRAM and register state. Gate the clocks of all unused peripherals via the PMU's SLEEPCFG register before sleep, and prefer the on-chip RTC (running from a 32.768 kHz crystal) to wake the core on a periodic schedule. Estimated: at 0.1% active duty cycle and 35 µA/MHz active current, average system current is approximately 17 µA on a 3 V supply - well within coin-cell capabilities.
The 48-QFN (7x7 mm) exposed pad must be soldered to a ground plane that is at least 25 mm² of 1 oz copper for thermal and electrical performance. Place decoupling capacitors (100 nF X7R + 4.7 µF X5R) within 3 mm of the VDD and VDDIO pins. Route the 32.768 kHz crystal traces short, guard them with a ground ring, and keep them away from switching signal lines to minimize jitter on the RTC and low-power timer.
Do not leave unused SERCOM pins floating; configure them as outputs driven low or enable the internal pull-downs to avoid parasitic current paths. The brown-out detector (BOD) should be enabled to prevent undefined behavior below 1.6 V. When migrating from SAM L21E to L21G, double-check the SERCOM instance count and PTC channel availability - the E variant trims some peripherals.
Informações de conformidade
RoHS and lead-free compliance confirmed per Microchip product page; AEC-Q100 not applicable for industrial-grade -40°C to +85°C parts.
