BCM5481A2IFBG - 1GbE RGMII PHY | Broadcom
N.º da peça: BCM5481A2IFBG ✓ AtivoBCM5481A2IFBG Visão geral
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts parallel digital data into signals suitable for transmission over twisted-pair copper cabling. The BCM5481A2IFBG belongs to the Gigabit Ethernet interface hierarchy: Ethernet controller or switch MAC, RGMII interface, Ethernet PHY, network interface, and semiconductor. Its 100-terminal package provides the mixed-signal and digital interface connections required by a complete single-port Gigabit Ethernet copper interface.
The BCM5481A2IFBG is identified as a 1-port Gigabit Ethernet PHY using RGMII and copper media technology. A nominal 1000 Mbps line rate supports full-duplex Gigabit Ethernet designs, while the RGMII interface provides a conventional parallel connection to an Ethernet MAC or switching fabric. These characteristics make the device relevant to designs that require a dedicated copper PHY rather than a PHY integrated into a larger Ethernet controller.
The device uses CMOS technology and is supplied in a square, 100-terminal ball-grid-style package identified in the component record as BCM5481A2IFBG. The component is listed as a Broadcom interface IC and is categorized among drivers, receivers, and transceivers. Its manufacturer-package quantity is 1, while the listed moisture-sensitivity classification is MSL1, indicating unlimited floor-life handling after the package has been subjected to the applicable moisture exposure conditions.
Typical BCM5481A2IFBG applications include 10/100/1000BASE-T network switches, industrial routers, telecommunications access equipment, set-top and home-gateway platforms, and embedded systems requiring an RGMII copper PHY. In these systems, the RGMII signals connect the PHY to a network MAC, while magnetics and the physical cable interface complete the copper path. The exact media-side implementation and magnetics selection should follow the Broadcom reference design and current datasheet.
Designers should confirm RGMII voltage levels, clocking mode, timing margins, decoupling, thermal performance, and the exposed-ball or land-pattern requirements before layout release. Because this package contains 100 terminals and mixes high-speed digital interfaces with analog Ethernet functions, short ground-return paths, clean supply distribution, controlled clock routing, and careful ball-pattern alignment are essential. Use the manufacturer pin-description table and layout guidance when assigning every ball and planning the PCB footprint.
This product page combines the verified BCM5481A2IFBG identity, package and interface details with practical Ethernet PHY design guidance, sourcing questions, and a structured framework for comparing replacement choices. It is intended to help engineers confirm fit, assess the RGMII copper-PHY application, and identify the documentation needed before committing a board to production.
Alternativas drop-in para BCM5481A2IFBG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasBCM5481A2IFBG Classificações máximas e características elétricas
| Taxa de dados | 1000 Mbps |
| Port Count | 1 port |
| Interface | RGMII |
| Media Type | Copper |
| Device Type | 1-port Gigabit Ethernet PHY |
| Technology | CMOS |
| Terminal Count | 100 terminals |
| Package Shape | Square |
| Tipo de montagem | Ball |
| Introduction Date | January 1, 2000 |
| Manufacturer Pack Quantity | 1 unit |
| Moisture Sensitivity Level | MSL1 (unlimited floor life) |
| ECCN | 5A991.b.1 |
| Country of Origin | China |
| Halogen-Free Status | Not compliant |
| Supply and Demand Status | Balanced |
| Maximum Link Rate | 1000 Mbps |
Guia de Configuração de Pinos do BCM5481A2IFBG square
Configuração de pinos para BCM5481A2IFBG (pacote square). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para BCM5481A2IFBG.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
BCM5481A2IFBG é adequado para 6 aplicaçãos: Gigabit Ethernet Network Switch, Industrial Router Ethernet Port, Telecommunications Access Equipment, Network Gateway, Embedded Communications Platform, Set-Top and Home Gateway.
Gigabit Ethernet Network Switch
BCM5481A2IFBG fits a copper Gigabit Ethernet switch port because it combines one 1000 Mbps PHY channel with an RGMII host interface and CMOS implementation. The RGMII connection can carry the parallel MAC-side data and control signals needed by a switching fabric, while the PHY performs the physical-layer function for twisted-pair copper media. A practical implementation must preserve RGMII timing, use an approved magnetics path, and follow the manufacturer layout for the 100-terminal ball package. The PHY should be validated together with the switch ASIC because reset timing, clocking, reference design, and link-equalization requirements can determine whether the interface works reliably at 1000 Mbps.
Recomendado
Industrial Router Ethernet Port
BCM5481A2IFBG can serve as the copper physical layer in an industrial router designed around a separate Ethernet MAC and RGMII fabric. Its single 1000 Mbps port is appropriate for a primary LAN uplink where higher bandwidth is preferred over a 100 Mbps-only interface. Industrial use requires confirmation of the applicable operating-temperature range and qualification status rather than assuming that general catalog availability is sufficient. Board planning should account for controlled impedance, robust magnetics and surge protection, isolated keep-alive power where required, and enough copper and ground-plane area for reliable high-speed and mixed-signal behavior.
Recomendado
Telecommunications Access Equipment
BCM5481A2IFBG is suitable for a 1000 Mbps copper access interface in telecommunications equipment where a dedicated RGMII PHY supports the line-side media function. The PHY can complement an access processor or switching ASIC that handles packet processing, control, and management. In this architecture, signal integrity across the RGMII connection and careful separation from the line-side magnetics are central to reliable operation. Designers should use the approved reference schematic and magnetics interface, define the link and auto-negotiation strategy, and validate the complete design across temperature, cable-length, and worst-case supply conditions.
Recomendado
Network Gateway
BCM5481A2IFBG can provide a high-speed copper Ethernet port in a gateway that connects a processor-based service platform to a local network. The RGMII interface permits a structured separation between the MAC or switch functionality and the physical transceiver, while the single-port configuration supports one Gigabit Ethernet link. Designers should confirm that the host processor can generate the required RGMII clocks and that the board architecture supports the required PHY supply domains. Ethernet magnetics, line-side protection, controlled-impedance routing, and solid grounding are necessary to turn the nominal 1000 Mbps capability into a robust physical interface.
Recomendado
Embedded Communications Platform
BCM5481A2IFBG can be used in an embedded communications platform that requires a dedicated 1000 Mbps copper PHY and a conventional parallel host interface. This arrangement can offload Ethernet physical signaling from an embedded processor while retaining RGMII as the connection to a MAC-capable companion device. The design must be checked carefully for clock-source direction, I/O voltage compatibility, reset timing, and startup sequencing. Because the device includes a dense 100-terminal mixed-signal package, PCB assembly constraints, ball-to-land alignment, via-in-pad policy, and thermal management should be resolved before mass production.
Recomendado
Set-Top and Home Gateway
BCM5481A2IFBG is applicable to a set-top box or home gateway that requires a wired Gigabit Ethernet connection for local media traffic. A single copper PHY can complement an integrated switching or connectivity controller while presenting a defined RGMII boundary to the rest of the design. Consumer-product implementations should verify environmental temperature, package assembly capability, and lifecycle continuity against the product's expected service life. The board should provide the prescribed supplies and decoupling, route RGMII as a short controlled-impedance interface, and use qualified Ethernet magnetics and protection components to withstand normal cable insertion and board-level ESD events.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BCM5481A2IFBG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Notas de projeto
Treat the RGMII interface as a short, controlled-impedance digital interface. Place the PHY close to the MAC or switch ASIC, match trace lengths according to the applicable RGMII clocking mode, and avoid stubs or unnecessary test pads on high-speed nets. Provide a continuous ground reference and use the manufacturer's reference layout to determine the RGMII voltage domain, clock-source direction, and decoupling connections.
The BCM5481A2IFBG uses a 100-terminal square ball package, so land-pattern accuracy, ball alignment, solder-mask and paste design, and assembly capability are central concerns. Do not infer the footprint from the package name alone; use the current manufacturer land pattern and verify pin assignments against the pin-description table. Establish a via strategy for thermal and electrical return paths based on the package construction and assembly process.
Separate the Ethernet media-side magnetics and protection network from RGMII clocks and other switching activity. Use the approved reference schematic and component placement to control common-mode and differential-mode energy around the PHY. Validate radiated and conducted emissions at the product level because a compliant PHY selection does not guarantee system-level EMC performance after PCB layout and enclosure integration.
Confirm clock direction, RGMII I/O voltage, reset polarity, and startup sequencing before connecting the MAC interface. A nominal 1000 Mbps PHY can fail link-up or exhibit timing errors when these details are mismatched. Use the datasheet timing diagrams and reference circuit rather than inferring behavior from generic Ethernet PHY conventions, especially when clocking modes or supply domains differ.
Informações de conformidade
The component record explicitly identifies the part as not halogen compliant and lists ECCN 5A991.b.1, MSL1, and a China country of origin. RoHS, REACH, AEC-Q100, lead-free, and conflict-minerals status require current manufacturer confirmation.