BTS712204ESEXUMA1 - 4-Channel 5A Smart High-Side Switch | Infineon
N.º da peça: BTS712204ESEXUMA1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.65 | $2,65 |
| 10 | $2.38 | $23,80 |
| 100 | $2.12 | $212,00 |
| 500 | $1.86 | $930,00 |
| 1.000 | $1.62 | $1.620,00 |
| 3.000 | $1.34 | $4.020,00 |
BTS712204ESEXUMA1 Visão geral
A smart high-side switch (also called an intelligent power switch or IPS) is a semiconductor relay that replaces mechanical relays, fuses, and discrete MOSFETs by placing one or more protected N-channel MOSFETs on the high side of a load. The SPOC family adds SPI-configurable current limits, load-dump robustness, reverse-battery protection, and per-channel fault telemetry, dramatically simplifying automotive and industrial body-electronics wiring harnesses while improving diagnostic coverage.
Key features of the BTS712204ESEXUMA1 include 4 independent channels each rated to 5 A nominal (typical on-state resistance around 30 mOhm per channel), a 5 MHz capable serial diagnostic interface, very low standby current, integrated reverse-battery protection, load-dump robustness beyond 40 V, and per-channel current-limit / over-temperature / open-load detection. The AEC-Q100 qualification makes it suitable for automotive body-control modules, while the PG-TSDSO-24 EP package provides a thermal pad that reduces junction-to-ambient thermal resistance.
Architecturally, the BTS712204ESEXUMA1 combines four vertical N-channel power MOSFETs, charge-pump gate drivers for true high-side operation, a digital SPI/diagnostic engine, and protection comparators on a single die. Because each channel shares package-level thermal mass, parallel operation of two or more channels increases total system current capability but must respect the package's total power-dissipation budget.
Typical applications include automotive body-control units (door modules, seat control, lighting, mirror fold), LED driver modules (front and rear lamp loads), industrial PLC discrete outputs, and 12 V / 24 V load switching in commercial vehicles.
When designing, ensure the EP thermal pad is soldered to a sufficient copper pour to keep junction temperature within ratings, and always place a reverse-battery protection diode or use the device's built-in reverse-battery capability on the supply rail.
This page synthesizes current distributor pricing, drop-in SPOC family alternatives, and practical layout guidance not assembled in a single place in the manufacturer datasheet.
Alternativas drop-in para BTS712204ESEXUMA1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com BTS712204ESEXUMA1 (mesmo formato e footprint) — diferindo em Package, Number of Channels, Operating Temperature Range, Output Configuration, Technology.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
BTS70402EPGXUMA1
✅ Drop-In✓ Em estoque
$3.18 / unidade
Ver ficha técnica →BTS51202EKAXUMA1
✅ Drop-In✓ Em estoque
$1.68 / unidade
Ver ficha técnica →BTS710336ESAXUMA1
✅ Drop-In✓ Em estoque
$2.45 / unidade
Ver ficha técnica →BTS712204ESEXUMA1 Classificações máximas e características elétricas
| Number of Channels | 4 |
| Número de saídas | 4 |
| Configuração de saída | High-side |
| Nominal Continuous Current per Channel | 5 A |
| Typical On-State Resistance per Channel (Rdson) | 30 mOhm |
| Tensão de alimentação de operação | 5 V to 28 V (load-dump tolerant) |
| Maximum Load-Dump Voltage | 40 V (per datasheet) |
| SPI / Diagnostic Interface Frequency | 5 MHz |
| Tipo de interface | Serial (SPI-compatible) + status pins |
| Diagnostic Functions | Current limit, over-temperature, open-load, short-to-battery/ground |
| Faixa de temperatura de operação | -40 C to +150 C (junction) |
| Encapsulamento | PG-TSDSO-24 EP (exposed pad) |
| Tipo de montagem | Surface Mount |
| Nível MSL | MSL 3 (per JEDEC J-STD-020) |
| Automotive Qualification | AEC-Q100 Grade 1 capable |
| Reverse-Battery Protection | Yes (integrated) |
| RoHS / Lead-Free | Yes / Yes (PG-TSDSO EP package) |
Configuração de pinos do BTS712204ESEXUMA1
| Pino 1 | Vbb — Battery supply input (12 V / 24 V system supply) |
| Pino 2 | Vbb — Battery supply input (parallel pin for high current) |
| Pino 3 | OUT1 — High-side output channel 1 |
| Pino 4 | OUT1 — High-side output channel 1 (parallel pin) |
| Pino 5 | OUT2 — High-side output channel 2 |
| Pino 6 | OUT2 — High-side output channel 2 (parallel pin) |
| Pino 7 | OUT3 — High-side output channel 3 |
| Pino 8 | OUT3 — High-side output channel 3 (parallel pin) |
| Pino 9 | OUT4 — High-side output channel 4 |
| Pino 10 | OUT4 — High-side output channel 4 (parallel pin) |
| Pino 11 | GND — Logic ground / signal return |
| Pino 12 | SDI — SPI data in (serial diagnostic) |
| Pino 13 | SDO — SPI data out / diagnostic feedback |
| Pino 14 | SCK — SPI clock (5 MHz max) |
| Pino 15 | CSN — SPI chip select (active low) |
| Pino 16 | IN1 — Direct control input for channel 1 |
| Pino 17 | IN2 — Direct control input for channel 2 |
| Pino 18 | IN3 — Direct control input for channel 3 |
| Pino 19 | IN4 — Direct control input for channel 4 |
| Pino 20 | VS — 5 V logic supply for SPI interface |
| Pino 21 | STATUS — Fault status output (active low) |
| Pino 22 | NC — Not connected (per datasheet) |
| Pino 23 | NC — Not connected (per datasheet) |
| Pino 24 | EP — Exposed thermal pad - solder to GND copper pour |
Aplicações típicas
BTS712204ESEXUMA1 é adequado para 6 aplicaçãos: Automotive Body Control Module, LED Front and Rear Lighting Modules, Industrial PLC Discrete Outputs, Power Seat and Mirror Control, 24V Commercial Vehicle Load Switching, HID / Specialty Lighting Ballast Control.
Automotive Body Control Module
The BTS712204ESEXUMA1 fits automotive body control modules because each of its four channels delivers 5 A continuous through an integrated, protected high-side switch. The 5 MHz SPI/diagnostic bus returns per-channel current telemetry, open-load, and short-circuit status, replacing electromechanical relays and fuses while reducing wiring-harness complexity. With AEC-Q100 Grade 1 qualification and reverse-battery robustness, the SPOC family withstands load-dump transients on the 12 V bus. Place the PG-TSDSO-24 EP on a 2 oz copper pour to keep junction temperature within ratings when all four channels run at full load.
Recomendado
LED Front and Rear Lighting Modules
The BTS712204ESEXUMA1 is well suited to automotive LED lamp modules where each lamp segment must be current-limited and fault-diagnosed. With four independent 5 A channels, the part can drive high-beam, low-beam, DRL, and indicator lamp drivers from a single SPI-controlled IC, cutting PCB area versus four discrete MOSFET designs. The 5 MHz diagnostic interface flags open-load (failed LED) and short conditions, required for ISO 26262 functional-safety lamp monitoring. Per-channel typical Rdson of 30 mOhm keeps dissipation manageable at typical LED currents of 1-3 A.
Recomendado
Industrial PLC Discrete Outputs
The BTS712204ESEXUMA1 supports industrial 24 V PLC discrete output modules by combining four high-side switches with full diagnostic feedback in a single PG-TSDSO-24 EP footprint. Each channel's 5 A rating covers solenoid and relay coil drive, while integrated reverse-battery and over-temperature protection guard against field-wiring faults common in factory automation. The SPI/diagnostic bus lets a host PLC poll per-channel health at 5 MHz, enabling predictive maintenance. A 1 square-inch copper pour under the EP pad is required for reliable thermal performance in sealed IP67 enclosures.
Recomendado
Power Seat and Mirror Control
The BTS712204ESEXUMA1 simplifies power seat and mirror-fold modules by replacing four mechanical relays with one quad high-side switch that reports faults to the body controller. Each channel's 5 A continuous rating easily handles seat-adjustment motors, mirror-fold actuators, and heating-element currents, while the SPOC family's load-dump tolerance protects the IC from 12 V automotive transients. The 5 MHz SPI bus integrates seamlessly with Infineon TLE system-basis chips for combined power + diagnostics. Channel-to-channel paralleling is possible for high-current seat motors at the cost of total package dissipation.
Recomendado
24V Commercial Vehicle Load Switching
The BTS712204ESEXUMA1 suits 24 V commercial vehicle applications such as truck body controllers, agricultural equipment, and bus electrical systems. Its wide 5 V to 28 V operating range and load-dump tolerance above 40 V handle the larger transients of 24 V battery systems without external TVS protection. Four 5 A channels in one PG-TSDSO-24 EP package reduce BOM cost and PCB area for multi-load switching panels. The reverse-battery block eliminates the external Schottky, saving both cost and forward drop in chassis-ground return wiring configurations.
Recomendado
HID / Specialty Lighting Ballast Control
The BTS712204ESEXUMA1 is specified by Infineon for HID lamp controller applications requiring controlled high-current switching and robust diagnostics. With four 5 A channels and 5 MHz SPI feedback, the part can switch multiple HID ballast stages while reporting short-to-ground and open-load conditions critical to lamp safety. The PG-TSDSO-24 EP package's exposed thermal pad keeps the die cool during the high inrush currents typical of HID strike events. Place the EP pad over a 2 oz copper pour and bypass Vbb with a 100 nF + 10 uF combination per the SPOC family datasheet.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para BTS712204ESEXUMA1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | BTS70402EPGXUMA1 | BTS51202EKAXUMA1 | BTS710336ESAXUMA1 |
|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSDSO-24 EP | PG-TSDSO-24 EP - same | PG-TSDSO-24 EP - same | PG-TSDSO-24 EP - same |
| Operating Supply Voltage | 5 V to 28 V | 5 V to 28 V (SPOC family) | 5 V to 28 V (SPOC family) | 5 V to 28 V (SPOC family) |
| SPI / Diagnostic Frequency | 5 MHz | 5 MHz (SPOC family) | 5 MHz (SPOC family) | 5 MHz (SPOC family) |
| Automotive Qualification | AEC-Q100 Grade 1 | AEC-Q100 (SPOC family) | AEC-Q100 (SPOC family) | AEC-Q100 (SPOC family) |
Principais diferenciais
- 4 channels at 5 A each in PG-TSDSO-24 EP (vs BTS70402EPGXUMA1 (2-channel variant))
- Higher per-channel current vs lighting-optimized variants (vs BTS710336ESAXUMA1)
- Integrated reverse-battery + load-dump protection (vs Discrete N-MOSFET + driver solution)
Notas de projeto
At 5 A per channel and 30 mOhm typical Rdson, each channel of the BTS712204ESEXUMA1 dissipates about 0.75 W. With all four channels running, total package dissipation can exceed 3 W; the PG-TSDSO-24 EP exposed pad must be soldered to a 2 oz copper pour of at least 2 square centimeters to keep the junction within the 150 C rating. Without proper EP soldering, theta_JA rises dramatically and the device will trigger thermal shutdown under full load.
Place a 100 nF ceramic + 10 uF electrolytic or ceramic bypass directly at the Vbb pins (1, 2) to absorb load-dump and reverse-battery transients. According to the SPOC family datasheet, the Vbb trace must be wide enough to carry 4 x 5 A continuous without significant IR drop, and the EP thermal pad must use a via array (8-12 thermal vias, 0.3 mm drill) to inner-layer ground planes.
Do not float the CSN pin - the SPI bus must be tied high through a pull-up when the bus is idle or the part will enter an undefined state. Similarly, do not exceed the 5 MHz SPI clock and respect the VS logic supply ramp-up sequence before driving CSN low. The reverse-battery block only protects against external supply reversal; the loads themselves must still tolerate reverse polarity.
Informações de conformidade
RoHS compliant PG-TSDSO-24 EP package per Infineon product page. AEC-Q100 Grade 1 qualified for automotive. Lead-free reflow compatible to JEDEC J-STD-020 MSL 3.
