CD4018BD3 - 5-Bit Divide-by-N CMOS Counter | Harris
N.º da peça: CD4018BD3 ✓ AtivoCD4018BD3 Visão geral
A CMOS counter is a digital logic IC that advances its internal count when it receives a triggering edge. Divide-by-N counters extend that function by producing an output transition only after a selected number of input events. In the broader semiconductor hierarchy, the CD4018BD3 belongs to the CD4000 CMOS logic series, which sits within the logic IC and digital counter categories. Its counter structure is particularly appropriate when the required division ratio can be established with external logic rather than implemented solely as a fixed binary sequence.
The key defining characteristics are the 5-bit counting capacity, positive-edge operation, programmable divide-by-N architecture, and 16-lead ceramic dual-in-line package. Positive-edge operation means the counter changes state in response to the designated transition on its clock input, which simplifies timing relationships when the part is combined with other edge-triggered CMOS logic. The 16-CDIP construction also provides a through-hole footprint suited to legacy industrial, control, and laboratory equipment.
CD4018B-family devices are produced in multiple package configurations, including 16-lead hermetic ceramic dual-in-line, 16-lead plastic dual-in-line, small-outline, and thin shrink small-outline formats. Package selection therefore depends on the PCB footprint, soldering process, environmental requirements, and mechanical constraints of the target assembly. The D3 designation identifies the CD4018BD3 configuration offered in the 16-CDIP format, while the underlying CD4018B function remains a CMOS presettable divide-by-N counter.
Typical uses include programmable pulse and timing generators, frequency dividers, delay counters, event-counting modules, and control logic for industrial or laboratory equipment. In these applications, the positive-edge input establishes a deterministic count boundary, while the preset and divide functions help align an output event with a chosen count interval. Cascading more than one counter stage can support additional division ranges when the system must produce a slower output from a higher-frequency clock.
PCB integration requires attention to the through-hole footprint and decoupling. Place the device so that no traces pass beneath the package unless the mechanical drawing explicitly permits it, route clock and preset/reset signals away from sensitive analog or high-speed nodes, and connect the supply and ground pins according to the manufacturer pin description. Because the exact electrical limits and pin functions are not reproduced in the retrieved catalog excerpt, use the manufacturer datasheet before finalizing supply voltage, clock timing, and logic-level constraints.
This page consolidates the verified package, counter configuration, sourcing references, and practical selection considerations for CD4018BD3. It also distinguishes the genuine same-footprint alternatives that can support design migration from options that may require a different footprint or package. For an exact electrical and mechanical release, verify the ordering suffix, pin assignment, and operating limits against the current manufacturer documentation before committing a production BOM.
Alternativas drop-in para CD4018BD3 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com CD4018BD3 (mesmo formato e footprint) — diferindo em Package, Counter Type, Logic Family.
CD4018BF3A
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
CD4018BE
✅ Drop-InConsulte o preço
Ver ficha técnica →CD4018BD
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
CD4018BE
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →CD4018BF
✅ Drop-InConsulte o preço
Ver ficha técnica →CD4018BD3 Classificações máximas e características elétricas
| Counter Type | Presettable divide-by-N counter |
| Number of Counting Elements | 1 element |
| Counting Capacity | 5 bits |
| Clock Edge | Positive edge |
| Logic Family | CD4000 CMOS |
| Encapsulamento | 16-CDIP |
| Package Width | 0.300 inch (7.62 mm) |
| Estilo de montagem | Through-hole |
| Lead Count | 16 leads |
Guia de Configuração de Pinos do CD4018BD3 0.300 inch (7.62 mm)
Configuração de pinos para CD4018BD3 (pacote 0.300 inch (7.62 mm)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para CD4018BD3.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
CD4018BD3 é adequado para 6 aplicaçãos: Programmable Frequency Divider, Retriggerable Timing and Delay Circuit, Event and Pulse Counting Module, Industrial Control Sequence Generator, Laboratory Pulse Generator and Divider, Legacy Instrumentation Retrofit.
Programmable Frequency Divider
The CD4018BD3 is suited to dividing a repetitive input signal when an established 16-lead through-hole counter is required. Its 5-bit, single-element divide-by-N architecture lets surrounding CMOS logic determine the division interval rather than relying on a fixed binary modulus alone. The positive-edge input establishes a clear timing boundary between counted events. In an existing control board, the 16-CDIP footprint allows the counter to be replaced without moving to a surface-mount footprint. Before implementation, verify the exact maximum clock frequency, propagation delay, and output timing from the manufacturer datasheet, because those limits determine the highest usable input repetition rate.
Recomendado
Retriggerable Timing and Delay Circuit
CD4018BD3 can form the counting element of a retriggerable timer because it advances on the positive clock edge and supports preset behavior within the CD4018B family. External preset and reset logic determines how many events must occur before the counter output changes state. This arrangement is useful in industrial control modules, laboratory instruments, and legacy timing boards that need an adjustable interval rather than a fixed monostable delay. The through-hole 16-CDIP package also supports repair and retrofit applications. Verify setup, hold, reset-release, and output-transition requirements in the manufacturer timing diagrams before using the counter close to its maximum operating frequency.
Recomendado
Event and Pulse Counting Module
The CD4018BD3 provides a compact event-counting function for machinery, test equipment, and control panels that must accumulate pulses and generate a state change after a selected count. Its single counting element and 5-bit architecture are appropriate when one counter stage is sufficient and additional division can be implemented with external logic. Positive-edge triggering helps separate the count boundary from other asynchronous activity when the source signal is properly conditioned. For retrofit work, the 0.300-inch, 7.62-mm 16-CDIP footprint matches the established through-hole layout. Confirm debounce or conditioning requirements at the source, then check the counter's maximum clock rate and output timing before connecting it to a higher-frequency sensor signal.
Recomendado
Industrial Control Sequence Generator
A CD4018BD3 can generate stepped control intervals in older industrial equipment by counting a periodic machine or controller signal. The divide-by-N architecture is useful when a production sequence must advance after a defined number of events, while preset and reset paths allow the sequence to be restarted or synchronized with another process stage. Using the 16-CDIP package helps maintain compatibility with hand-soldered repair assemblies and through-hole backplanes. The design should include a defined clock source, appropriate logic levels, and a reset strategy that cannot leave the counter in an intermediate state. Confirm propagation delays and electrical ratings against the manufacturer documentation before cascading counters or driving long control lines.
Recomendado
Laboratory Pulse Generator and Divider
CD4018BD3 is applicable in laboratory instruments that need to reduce a stable oscillator frequency to a lower inspection or trigger rate. The 5-bit counter and programmable division behavior support simple divide-by-N networks, while the positive-edge input provides a deterministic sampling point for the output state. A 16-CDIP package is practical for instrument prototypes, educational hardware, and repair boards that use through-hole construction. To obtain useful timing accuracy, use a clean clock source and compare the counter's propagation delay with the target output period. The manufacturer timing characteristics and recommended operating conditions must be reviewed before selecting a supply voltage or operating frequency for the counter stage.
Recomendado
Legacy Instrumentation Retrofit
CD4018BD3 is useful when servicing an older instrument whose original counting section used a 16-CDIP presettable divide-by-N counter. The ceramic dual-in-line format and through-hole construction make it practical for repair boards populated manually or with through-hole assembly equipment. Its 5-bit single-element structure matches the catalog description of the original function, while positive-edge operation must be reconciled with the timing relationships of the surrounding gates and flip-flops. Before fitting the device, compare the complete ordering code, pinout, supply requirements, and qualification level with the removed component. The exact electrical operating envelope and environmental ratings should come directly from the applicable manufacturer datasheet.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para CD4018BD3 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | CD4018BF3A | CD4018BE | CD4018BD | CD4018BE | CD4018B |
|---|---|---|---|---|---|---|
| Brand | Harris Corporation | Texas Instruments | Texas Instruments | Harris Corporation | Harris Corporation | Texas Instruments |
| Package | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP (0.300 inch, 7.62 mm) | 16-CDIP family configuration |
| Counter Function | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter | Presettable divide-by-N counter |
| Counting Capacity | 5 bits | 5 bits | 5 bits | 5 bits | 5 bits | 5 bits |
| Counting Elements | 1 element | 1 element | 1 element | 1 element | 1 element | 1 element |
| Clock Edge | Positive edge | Positive edge | Positive edge | Positive edge | Positive edge | Positive edge |
| Logic Technology | CD4000 CMOS | CD4000 CMOS | CD4000 CMOS | CD4000 CMOS | CD4000 CMOS | CD4000 CMOS |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole | Through-hole | Package-dependent; 16-lead dual-in-line option |
Principais diferenciais
- Exact Harris Corporation CD4018BD3 configuration (vs CD4018B)
- Hermetic ceramic dual-in-line family option (vs CD4018BE)
- Same 5-bit divide-by-N core architecture (vs CD4018BF3A)
- Positive-edge timing compatibility (vs CD4018BD)
Notas de projeto
Treat CD4018BD3 as a through-hole 16-CDIP component with a 0.300-inch, 7.62-mm body width. Confirm hole diameter, row spacing, and lead length against the package drawing before releasing artwork. Place it away from board edges and heavy connectors where insertion or rework could stress the ceramic package. If replacing an existing design, compare the complete numbered pin orientation rather than relying on the family name alone.
Route the clock as the principal timing signal and keep it short and isolated from noisy switching nodes. Because CD4018BD3 is a positive-edge counter, source timing and recovery relationships can determine whether a given clock transition is accepted. Use the manufacturer timing diagram to establish setup, hold, pulse-width, and preset/reset constraints, and terminate or condition external sensor signals before they enter the clock input.
Connect supply and ground pins directly to a low-impedance plane and place the manufacturer's recommended bypassing capacitor close to the device. Do not infer the permissible supply voltage from the CD4000 family name alone because the exact CD4018B grade can differ. Use the ordering-code and operating-limit sections of the manufacturer datasheet before connecting the counter to an existing 5 V or 10 V logic rail.
Avoid substituting by function name alone. A CD4018B variant in a small-outline or thin shrink small-outline package does not fit a 16-CDIP footprint, and a suffix change may also alter temperature grade, qualification, or package material. For a true drop-in decision, compare the full ordering code, pinout, electrical limits, timing characteristics, and lifecycle status. Do not use the base CD4018B family designation as a production order code without selecting a complete suffix.
Informações de conformidade
The retrieved catalog and family documentation do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for the exact CD4018BD3 ordering code.