EFM32ZG108F16-B-QFN24 - 24MHz Cortex-M0+ MCU | Silicon Labs
N.º da peça: EFM32ZG108F16-B-QFN24 ✓ AtivoEFM32ZG108F16-B-QFN24 Visão geral
A microcontroller is a programmable semiconductor that integrates a processor core, memory, digital I/O, timers, and peripherals on one integrated circuit. In the power-management hierarchy, this ARM Cortex-M0+ MCU belongs to the embedded-controller class and combines general-purpose 32-bit processing with energy-conscious peripherals. The EFM32 Zero Gecko family is particularly suited to battery-operated systems, smart meters, sensors, and industrial devices that spend substantial time in low-power states.
Key features include 24 MHz processing performance, 16 kB of embedded Flash, 4 kB of SRAM, 17 GPIO pins, and 2 x 16-bit timers. Silicon Labs emphasizes low-power operation, including Stop-mode consumption as low as 0.5 uA and Run-mode consumption of 114 uA/MHz. The 1.98 V to 3.8 V operating range supports low-voltage systems, while the compact 24-QFN package helps reduce board area in wearable, metering, and embedded-control products.
The EFM32ZG108 architecture combines an ARM Cortex-M0+ core with configurable peripheral locations and energy-saving hardware. Its 17 I/O pins can be assigned flexibly through the device configuration mechanism, reducing the need for external multiplexing in compact designs. Two 16-bit timers support periodic events, timing measurements, and motor or waveform control. The manufacturer documentation also identifies autonomous peripheral operation as a family-level feature that can reduce CPU involvement during selected low-energy tasks.
Typical applications include smart energy meters, water and gas meters, industrial sensor nodes, portable medical accessories, compact environmental monitors, and low-power IoT devices. In these systems, the MCU can manage sensor acquisition, scheduled measurements, communications, and local status indication while retaining state through multiple energy-saving states. The 24 MHz Cortex-M0+ core provides sufficient performance for protocol handling and modest control tasks without requiring a higher-complexity processor.
PCB implementation requires careful attention to the exposed pad, analog and digital supply connections, and high-frequency decoupling. The EFM32ZG family documentation states that AVDD_x, VDD_DREG, and IOVDD_x pins must be connected together at the PCB level, optionally with filtering. Follow the manufacturer pin-description table and hardware-design guidance before assigning tracks, and place decoupling capacitors close to their associated supply pins.
This product page combines the manufacturer specifications with engineering-focused application guidance, pin and footprint considerations, drop-in alternatives, and parameter-by-parameter comparison. These details help engineers assess fit before committing the EFM32ZG108F16-B-QFN24 to a low-power embedded design.
Alternativas drop-in para EFM32ZG108F16-B-QFN24 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com EFM32ZG108F16-B-QFN24 (mesmo formato e footprint) — diferindo em Flash Memory, Package, Timers, Low-Power Features, Digital I/O Pins.
EFM32ZG108F16-QFN24
✅ Drop-InConsulte o preço
Ver ficha técnica →EFM32ZG108F16-QFN24T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EFM32ZG108F32-B-QFN24
✅ Drop-InConsulte o preço
Ver ficha técnica →EFM32ZG108F32-QFN24
✅ Drop-InConsulte o preço
Ver ficha técnica →EFM32ZG108F4-QFN24
✅ Drop-InConsulte o preço
Ver ficha técnica →EFM32ZG108F16-B-QFN24 Classificações máximas e características elétricas
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Maximum CPU Frequency | 24 MHz |
| Core Architecture | ARM Cortex-M0+ |
| Flash Memory | 16 kB |
| RAM Memory | 4 kB |
| Digital I/O Pins | 17 pins |
| Timers | 2 x 16-bit timers |
| Supply Voltage Range | 1.98 V to 3.8 V |
| Run Mode Current | 114 uA/MHz |
| Stop Mode Current | 0.5 uA |
| Encapsulamento | 24-QFN (5 x 5 mm) |
| Tipo de montagem | Surface mount |
| Processor Word Size | 32-bit |
| Flash Organization | 16 kB (16K x 8) |
| RAM Organization | 4 kB |
| Single-Core Configuration | 1 core |
| Low-Power Modes | Stop mode and additional energy-saving modes |
Guia de Configuração de Pinos do EFM32ZG108F16-B-QFN24 24-qfn (5 x 5 mm)
Configuração de pinos para EFM32ZG108F16-B-QFN24 (pacote 24-qfn (5 x 5 mm)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para EFM32ZG108F16-B-QFN24.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
EFM32ZG108F16-B-QFN24 é adequado para 6 aplicaçãos: Battery-Powered Smart Meter, Industrial Sensor Node, Portable Health Monitor, Smart Metering Communication Module, Environmental Monitoring Device, Low-Power IoT Controller.
Battery-Powered Smart Meter
The EFM32ZG108F16-B-QFN24 fits smart energy meters because it combines a 24 MHz ARM Cortex-M0+ processor with 16 kB Flash and 4 kB RAM for measurement control, data processing, and communications support. Its 17 digital I/O pins can support pulse inputs, status indicators, and control signals, while two 16-bit timers support periodic sampling. The low-power platform reaches as little as 0.5 uA in Stop mode, helping conserve battery energy during long idle periods. The 24-QFN 5 x 5 mm package also reduces board area compared with a larger leaded package, although the exposed pad requires careful layout and soldering.
Recomendado
Industrial Sensor Node
The EFM32ZG108F16-B-QFN24 is appropriate for distributed industrial sensor nodes that periodically measure a physical quantity, check thresholds, and report status over a low-power link. Its 24 MHz Cortex-M0+ core can execute protocol and control tasks, while the 16 kB Flash and 4 kB RAM provide space for application code, configuration data, and short measurement buffers. Configurable peripheral locations help reduce I/O conflicts in compact designs, and the 1.98 V to 3.8 V supply range supports regulated low-voltage rails. For reliable industrial deployment, verify the exact peripheral set, watchdog behavior, and environmental requirements against the manufacturer documentation.
Recomendado
Portable Health Monitor
The EFM32ZG108F16-B-QFN24 can serve as the control MCU in a portable health monitor that samples sensors, drives a small display, records events, and manages a rechargeable power source. The 24 MHz ARM Cortex-M0+ processor is suitable for the modest computation required by typical sensing and user-interface routines, while 4 kB RAM supports short-lived data handling. Stop-mode current as low as 0.5 uA is useful when the monitor spends most of its operating life between measurements. Medical classification and regulatory requirements depend on the complete product, so this MCU should not be treated as automatically qualified for every medical application.
Recomendado
Smart Metering Communication Module
The EFM32ZG108F16-B-QFN24 is well suited to metering communication modules that authenticate messages, exchange short data frames, and supervise an RF or wired transceiver. Its 24 MHz Cortex-M0+ core provides adequate throughput for lightweight protocol processing, and 16 kB Flash accommodates a compact protocol stack and configuration. Two 16-bit timers can support communication timing, sensor sampling, or watchdog-related tasks. Keep the radio burst-current profile separate from the MCU specification, and validate the regulator, antenna, and transceiver path against the complete RF design rather than assuming the controller's low-power figures determine system consumption.
Recomendado
Environmental Monitoring Device
The EFM32ZG108F16-B-QFN24 fits compact environmental monitors that periodically sample temperature, humidity, air quality, or light data and transmit occasional readings. The 17 GPIO pins provide flexible interfaces to sensors and indicators, while configurable peripheral assignments help reduce external multiplexing. Low-power operation is central to this use case: the family is specified at 114 uA/MHz in Run mode and as little as 0.5 uA in Stop mode. The 5 x 5 mm QFN package helps achieve a small enclosure, but exposed-pad soldering, supply filtering, and sensor-heater power demands should be included in the complete thermal and power budget.
Recomendado
Low-Power IoT Controller
The EFM32ZG108F16-B-QFN24 is appropriate for a low-power IoT controller that gathers local sensor data, applies control logic, and activates a communication module only when necessary. Its 24 MHz Cortex-M0+ core, 16 kB Flash, and 4 kB RAM are suitable for compact firmware, while the 1.98 V to 3.8 V operating range simplifies integration with low-voltage power systems. The MCU's Stop mode can reduce consumption between events to as little as 0.5 uA. Actual IoT battery life also depends on wireless transmit energy, sensor duty cycle, leakage, and regulator efficiency, so validate the complete power tree under field-like conditions.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para EFM32ZG108F16-B-QFN24 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | EFM32ZG108F16-QFN24 | EFM32ZG108F16-QFN24T | EFM32ZG108F32-B-QFN24 | EFM32ZG108F32-QFN24 | EFM32ZG108F4-QFN24 |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 24-QFN (5 x 5 mm) | 24-QFN (5 x 5 mm) - same | 24-QFN (5 x 5 mm) - same | 24-QFN (5 x 5 mm) - same | 24-QFN (5 x 5 mm) - same | 24-QFN (5 x 5 mm) - same |
| CPU Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Frequency | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz | 24 MHz |
| Flash Memory | 16 kB | 16 kB | 16 kB | 32 kB | 32 kB | 4 kB |
| RAM Memory | 4 kB | 4 kB | 4 kB | 4 kB | 4 kB | 4 kB |
| Digital I/O Pins | 17 pins | 17 pins | 17 pins | 17 pins | 17 pins | 17 pins |
Principais diferenciais
- Balances embedded memory and low-power operation (vs EFM32ZG108F32-B-QFN24)
- Offers substantially more program memory than the minimum-memory family option (vs EFM32ZG108F4-QFN24)
- Exact electrical configuration with same-family order-code options (vs EFM32ZG108F16-QFN24)
- Combines compact packaging with dedicated timer resources (vs EFM32ZG108F32-QFN24)
Notas de projeto
Implement the manufacturer recommended land pattern for the 24-QFN 5 x 5 mm package and its exposed pad. The exposed pad is an electrical and thermal connection, not an unused center pin. Place each decoupling capacitor directly beside its associated supply pin and provide a low-impedance ground return. Avoid routing sensitive analog signals beneath the MCU, power-regulator output, or high-speed switching nodes where coupling could disturb sensitive measurements.
The EFM32ZG documentation requires AVDD_x, VDD_DREG, and IOVDD_x to be connected together at the PCB level, optionally with filtering. Follow that arrangement exactly rather than treating each label as an independent power domain. Select the supply range and regulator for the complete board, then place bulk and high-frequency decoupling close to the package. Validate startup, brownout behavior, and voltage margins under worst-case temperature and load conditions.
The 5 x 5 mm QFN relies heavily on its exposed pad and PCB copper for heat dissipation. Use the manufacturer thermal information and land pattern to estimate junction temperature, and add thermal vias only where the recommended footprint permits them. Keep the MCU away from heat sources such as an LCD regulator, radio power amplifier, or switching converter. For battery systems, calculate average energy separately from peak current because short radio or sensor bursts can dominate the power budget.
Do not substitute a different Flash-density device without checking firmware capacity, linker assumptions, and boot behavior. The EFM32ZG108F32 variants provide 32 kB rather than 16 kB, while the F4 variant provides 4 kB rather than 16 kB; both changes can affect production configuration even though the package remains the same. Also confirm whether the original order code requires a tray, cut tape, or reel because the electrical match does not determine the correct packing format.
Plan the pin assignment before routing because the EFM32 Zero Gecko platform uses configurable peripheral locations. Assign high-speed or timing-sensitive functions according to the manufacturer peripheral-location guidance, and reserve programming and reset access for manufacturing or recovery. Keep oscillator and sensitive analog paths away from switching traces and the exposed-pad region. Review the pin-description table for alternate functions, because a signal connected to the wrong peripheral instance may appear electrically correct but operate at a different performance level.
Informações de conformidade
Confirm environmental, automotive, and material compliance with Silicon Labs for the exact EFM32ZG108F16-B-QFN24 order code before production release.