GRM188R60J106ME47D - 10µF 6.3V X5R 0603 MLCC | Murata
N.º da peça: GRM188R60J106ME47D ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0.1 | $0,10 |
| 10 | $0.07 | $0,70 |
| 100 | $0.038 | $3,80 |
| 500 | $0.028 | $14,00 |
| 1.000 | $0.022 | $22,00 |
| 4.000 | $0.016 | $64,00 |
GRM188R60J106ME47D Visão geral
What is an MLCC? A multilayer ceramic capacitor is a passive surface-mount component formed by alternating thin dielectric ceramic layers and metal electrode layers, sintered into a monolithic block with termination caps on each end. The 0603 imperial code corresponds to 1.6 mm × 0.8 mm (1608 Metric). The X5R dielectric class (EIA standard) specifies ±15% capacitance variation over -55 °C to +85 °C and a maximum rated temperature of 85 °C, which suits virtually all commercial decoupling rails. MLCCs sit in the taxonomy: capacitor → ceramic capacitor → multilayer ceramic capacitor (MLCC) → SMD passive component.
Key features include 10 µF nominal capacitance in the 0603 footprint, 6.3 V DC rated voltage, ±20% capacitance tolerance at 25 °C, X5R temperature characteristic, 1 mm max thickness, and Ni-barrier + Sn plating on copper terminations for lead-free reflow compatibility. Compared with electrolytic alternatives the part offers far lower ESR, zero polarity risk, no dry-out, and RoHS-compliant materials.
Technically, the GRM series uses a base-metal-electrode (BME) Ni inner-electrode construction with X5R barium-titanate-based dielectric. BME technology enables the high capacitance per unit volume that defines the GRM Hi-Cap family (1 µF and above). The 6.3 V rating indicates that DC bias derating must be observed: at rated voltage a 10 µF X5R part typically retains 50-70% of nominal capacitance due to the dielectric's voltage coefficient.
Typical applications include bulk decoupling on 3.3 V and 5 V logic rails, point-of-load filtering for microcontrollers and SoCs, smartphone and wearable power management, audio codec reference rails, USB/HDMI interface line filtering, and bypass for low-dropout (LDO) regulators and DC-DC converter outputs. The 0603 footprint is the most common land pattern in modern PCB design libraries, ensuring drop-in compatibility with the widest range of reference designs.
Design consideration: confirm that the actual DC bias on the rail does not exceed 6.3 V and account for AC ripple; X5R exhibits significant capacitance loss versus DC bias and temperature. For tighter stability, an X7R or C0G alternative at the same 0603 footprint may be preferable on sensitive analog nodes.
This page synthesises distributor pricing, drop-in cross-brand equivalents, and practical bypass-layout guidance not found in the bare manufacturer datasheet, supporting faster component selection and BOM risk reduction.
Alternativas drop-in para GRM188R60J106ME47D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com GRM188R60J106ME47D (mesmo formato e footprint) — diferindo em Capacitance, Mounting Type, Rated Voltage (DC).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
GRM188R60J106KE47D
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
GRM188R60J106ME47J
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
GRM188R60G106ME47D
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
CL10A106KP8NNNC
✅ Drop-In✓ Em estoque
$0.009 / unidade
Ver ficha técnica →C1608X5R0J106K080AB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
CC0603KRX5R6BB106
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
EMK107BBJ106MA8T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
GRM188R60J106ME47D Classificações máximas e características elétricas
| Capacitance | 10 µF |
| Capacitance Tolerance | ±20% |
| Rated Voltage (DC) | 6.3 V |
| Dielectric Characteristic | X5R (EIA) |
| Encapsulamento / Caixa | 0603 (1608 Metric) |
| Length | 1.6 mm |
| Width | 0.8 mm |
| Thickness (max) | 1.0 mm |
| Faixa de temperatura de operação | -55 °C to +85 °C |
| Termination Style | SMD / Solder Pad |
| Termination Plating | Ni barrier + Sn (lead-free) |
| Tipo de montagem | Surface Mount |
| Packaging | Tape & Reel (paper carrier, 7-inch) |
| Nível MSL | MSL 1 (JEDEC J-STD-020) |
| Status RoHS | Compliant |
| Capacitor Family | GRM Series / Hi-Cap (≥1 µF) |
| Construction | Multilayer Ceramic (BME Ni inner electrodes) |
Guia de Configuração de Pinos do GRM188R60J106ME47D 0603 (1608 metric)
Configuração de pinos para GRM188R60J106ME47D (pacote 0603 (1608 metric)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para GRM188R60J106ME47D.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
GRM188R60J106ME47D é adequado para 6 aplicaçãos: Bulk Decoupling for Microcontroller / SoC Rails, LDO and DC-DC Converter Output Filtering, Smartphone and Wearable Power Management, USB / HDMI / DisplayPort Interface Bypass, Audio Codec Power Rail Bypass, Industrial Sensor and IoT Node Power Decoupling.
Bulk Decoupling for Microcontroller / SoC Rails
The GRM188R60J106ME47D provides 10 µF bulk charge reservoir on 3.3 V and 5 V microcontroller power rails. The 6.3 V rating gives comfortable margin above 3.3 V rails and small headroom on 5 V rails. Why this part fits: the 0603 footprint is the most common land pattern in MCU reference designs, and the X5R dielectric maintains sufficient capacitance at typical 3.3 V bias where derating leaves roughly 6-7 µF effective. The 1 mm max thickness fits beneath tight keep-out zones near BGAs. Place the part within 2 mm of the IC VDD pin with a 0.1 µF X7R 0402 in parallel for high-frequency decoupling - the X5R bulk handles low-frequency transient demands up to a few hundred kHz, while the smaller X7R handles switching edges above 1 MHz. Compared with a tantalum or polymer cap, the GRM188R60J106ME47D adds zero ESR variation across temperature and no derating on storage.
Recomendado
LDO and DC-DC Converter Output Filtering
The GRM188R60J106ME47D sits on the output of low-dropout regulators and buck converters to suppress load-transient spikes and reduce output ripple. Why this part fits: with 10 µF effective capacitance at 3.3 V output bias and ESR below 10 mΩ, it absorbs the instantaneous current steps demanded by digital loads during clock edges, preventing the LDO output from sagging. Place within 3 mm of the regulator output pin with the shortest possible trace to ground via the regulator GND pin - the 0603 size allows placement directly adjacent to the LDO without crowding the thermal pad. For 5 V rails, the 6.3 V rating requires that transient overshoot never exceed 6.3 V; otherwise move to a 10 V or 16 V X5R alternative. Performance trade-off versus a tantalum capacitor: lower ESR means better high-frequency transient response but less ESR-zero damping, so adding a small series resistor (10-50 mΩ) or using a polymer tantalum can improve loop stability of the regulator.
Recomendado
Smartphone and Wearable Power Management
The GRM188R60J106ME47D is widely used in smartphone PMIC output rails, wearable battery management, and Bluetooth audio SoC supply pins. Why this part fits: at 1.6 mm × 0.8 mm × 1.0 mm it occupies the smallest standard high-capacitance MLCC land pattern, allowing dense routing on flex PCBs and 4-layer smartphone motherboards. The 10 µF/6.3 V combination covers PMIC buck output filtering where 1-2 V rails drop to <100 mV ripple. Ni-barrier + Sn terminations survive SAC305 lead-free reflow at 260 °C peak per JEDEC J-STD-020 and remain stable across -20 °C to +60 °C wearable operating profiles. Performance consideration: the X5R dielectric loses approximately 30-50% of nominal capacitance under DC bias, so a design that nominally expects 10 µF may only see 5-7 µF at full rated voltage - oversize the cap count rather than rely on a single part for bulk energy storage on critical rails.
Recomendado
USB / HDMI / DisplayPort Interface Bypass
The GRM188R60J106ME47D provides bulk bypass on USB 2.0/3.0 VBUS, HDMI +5 V supply, and DisplayPort AUX power pins where a stable 4.75-5.25 V rail is required. Why this part fits: at 5 V nominal operation the 6.3 V rating gives only 26% voltage headroom, which is acceptable for USB/HDMI compliant supplies but requires careful layout to prevent hot-plug transients from exceeding 6.3 V. Place the cap directly at the connector VBUS pin with a 0.1 µF X7R 0402 in parallel for EMI suppression of high-frequency common-mode noise. The 0603 size allows mounting on the small connector keep-out without exceeding connector shadow. Trade-off versus X7R: X5R offers higher capacitance density for the same 0603 footprint, but X7R maintains more capacitance under DC bias and would be preferable on rails with >5 V continuous voltage.
Recomendado
Audio Codec Power Rail Bypass
The GRM188R60J106ME47D is paired with smaller-value X7R/C0G capacitors on audio codec AVDD/DVDD rails to suppress power-rail noise coupling into the audio signal path. Why this part fits: at 10 µF it absorbs low-frequency supply ripple from upstream DC-DC converters and PMIC LDOs that would otherwise modulate ground reference and inject hum into headphone outputs. The 0603 footprint allows placement adjacent to codec supply pins on densely-routed audio daughter boards. Performance consideration: the X5R dielectric voltage coefficient means that at 3.3 V AVDD, effective capacitance may drop to ~6-7 µF - supplement with a 1 µF or 2.2 µF C0G 0402 in parallel if low-ESR stability below 20 Hz is required for noise-shaping performance. Do not use this part directly in the audio signal path - only on supply rails.
Recomendado
Industrial Sensor and IoT Node Power Decoupling
The GRM188R60J106ME47D delivers bulk capacitance on industrial sensor module rails, IoT node power supplies, and 4-20 mA loop transmitter outputs where reliability over -40 °C to +85 °C industrial temperature range is required. Why this part fits: the X5R dielectric specification maintains ±15% capacitance variation across the full industrial temperature window, and the Ni+Sn lead-free termination withstands high-humidity industrial environments. The 0603 footprint is the de-facto standard for industrial sensor PCBs, allowing easy sourcing from multiple distributors and reducing single-source supply risk. Place within 5 mm of each sensor IC supply pin with a 0.1 µF X7R in parallel; the bulk GRM188R60J106ME47D handles transient load steps during sensor activation, while the X7R handles high-frequency switching noise. Trade-off versus tantalum capacitors on long-life industrial designs: the GRM MLCC has no wear-out mechanism from electrolyte dry-out, providing 10+ year reliability in permanently-installed sensor nodes.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para GRM188R60J106ME47D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | GRM188R60J106KE47D | GRM188R60J106ME47J | GRM188R60G106ME47D | CL10A106KP8NNNC | C1608X5R0J106K080AB | CC0603KRX5R6BB106 | EMK107BBJ106MA8T |
|---|---|---|---|---|---|---|---|---|
| Package | 0603 (1608 Metric) | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same | 0603 (1608 Metric) - same |
| Brand | Murata Manufacturing | Murata Manufacturing | Murata Manufacturing | Murata Manufacturing | Samsung Electro-Mechanics | TDK | Yageo | Taiyo Yuden |
| Capacitance | 10 µF | 10 µF | 10 µF | 10 µF | 10 µF | 10 µF | 10 µF | 10 µF |
| Rated Voltage | 6.3 V | 6.3 V | 6.3 V | 6.3 V | 10 V (higher rating) | 6.3 V | 6.3 V | 6.3 V |
| Dielectric | X5R | X5R | X5R | X7R (tighter) | X5R | X5R | X5R | X5R |
| Capacitance Tolerance | ±20% | ±10% | ±20% | ±20% | ±10% | ±10% | ±10% | ±20% |
| Operating Temperature | -55 °C to +85 °C | -55 °C to +85 °C | -55 °C to +85 °C | -55 °C to +125 °C | -55 °C to +85 °C | -55 °C to +85 °C | -55 °C to +85 °C | -55 °C to +85 °C |
| Termination | Ni barrier + Sn | Ni barrier + Sn | Ni barrier + Sn | Ni barrier + Sn | Ni barrier + Sn | Ni barrier + Sn | Ni barrier + Sn (lead-free) | Ni barrier + Sn |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Higher capacitance density than 0805-class parts at the 0603 footprint (vs Generic 10 µF X5R 0805 MLCCs)
- Cross-brand drop-in compatibility with major MLCC suppliers (vs TDK C1608X5R0J106K080AB and Samsung CL10A106KP8NNNC)
- Industry-leading volume pricing at full reel quantities (vs Taiyo Yuden EMK107BBJ106MA8T and Yageo CC0603KRX5R6BB106)
Notas de projeto
DC bias derating is the most common pitfall with X5R 10 µF 6.3 V MLCCs. At the rated 6.3 V DC, the GRM188R60J106ME47D typically retains only 50-70% of nominal capacitance (i.e. 5-7 µF effective out of 10 µF nominal). On 3.3 V rails the loss is smaller (~30%), but on 5 V rails close to the rated voltage the effective capacitance drops sharply. When the design needs a guaranteed minimum capacitance (e.g. for an LDO output), either use multiple GRM188R60J106ME47D caps in parallel or upgrade to a 10 V or 16 V X5R/X7R alternative to reduce voltage derating. Always check the manufacturer's actual DC-bias curve in the GRM series datasheet rather than assuming nominal capacitance holds across the operating voltage range.
Place the GRM188R60J106ME47D within 2-3 mm of the IC supply pin it is decoupling, with the shortest possible trace to the IC's GND pad. Use 0.1 µF and 1 nF X7R 0402 caps in parallel for high-frequency decoupling; the 10 µF X5R bulk handles low-frequency transient loads while the smaller values handle switching edges above 1 MHz. Land pattern per IPC-7351 nominal 0603: rectangular pads 0.9 mm × 0.7 mm with 1.0 mm centre-to-centre spacing. Avoid placing the part under tall components or near board edges where mechanical stress can flex the PCB and crack the ceramic body - this is the leading cause of MLCC failures in the field. Use a symmetric pad layout to avoid polarity-induced stress.
Although MLCCs do not dissipate significant heat under normal operation, the GRM188R60J106ME47D must survive lead-free reflow at peak 260 °C per JEDEC J-STD-020. Pre-heating should ramp at 1-3 °C/s to 150 °C, soak 60-150 s, then ramp to peak 260 °C for 20-40 s above 255 °C. Avoid thermal shock: do not place MLCCs on the bottom side of a double-sided board being reflowed for the second time without confirming the component has cooled below 50 °C. The part is rated MSL 1 (unlimited floor life), so no special moisture-sensitive handling is required, but exposure to high humidity during storage (>30 days at >85% RH) is not recommended by Murata for any MLCC.
Informações de conformidade
RoHS compliant, REACH compliant, lead-free Ni+Sn terminations per Murata GRM series datasheet. AEC-Q100 not applicable (passive component). MSL 1 per JEDEC J-STD-020.
