ISD8104RYI - 2W Class AB Audio Amplifier | Nuvoton
N.º da peça: ISD8104RYI ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0.62 | $0,62 |
| 10 | $0.56 | $5,60 |
| 100 | $0.48 | $48,00 |
| 500 | $0.42 | $210,00 |
| 1.000 | $0.37 | $370,00 |
ISD8104RYI Visão geral
A Class AB audio amplifier is a linear power amplifier topology in which output transistors conduct continuously through the signal cycle, combining the low distortion of Class A designs with the improved efficiency of Class B. Within the power management and audio signal chain hierarchy, it sits downstream of DACs or codec outputs and upstream of the loudspeaker, converting line-level analog signals into speaker-drive-capable power. The ISD8104 belongs to Nuvoton's ISD audio amplifier product line, alongside the ISD8102, which differs by offering an earphone-sense input (SE/Diff) instead of a dedicated differential input pair.
Key features include 2W output power at mono Class AB operation, a true differential input pair that rejects common-mode noise picked up on the PCB, and a chip enable (CE) pin that allows the system controller to shut the amplifier down and minimize standby current draw in battery-powered products. The differential input architecture is significant for designs where the amplifier sits far from the signal source, such as alarm panels or appliance panels.
The Class AB output stage provides low crossover distortion, important for voice-band announcement and alerting audio where intelligibility matters more than maximum efficiency. Typical applications include doorbell and intercom systems, industrial alarm sounders, small appliance voice prompts, toys, and battery-powered notification devices.
When designing with the ISD8104RYI, consult the manufacturer datasheet for gain-setting resistor values, supply voltage limits, and the thermal pad soldering requirements, since power dissipation in a 2W Class AB stage depends strongly on supply voltage and load impedance.
This page synthesizes distributor listings, same-family drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para ISD8104RYI — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
ISD8104SYI
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
ISD8102SYI
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
ISD8104RYI Classificações máximas e características elétricas
| Amplifier Type | Class AB Audio Power Amplifier |
| Output Power | 2 W |
| Canais | 1 (Mono) |
| Input Type | Differential Input Pair |
| Control Feature | Chip Enable |
| Encapsulamento | 8-SOP with thermal pad (RYI) |
| Tipo de montagem | Surface Mount |
| Manufacturer | Nuvoton Technology Corporation |
| Product Family | ISD Audio Amplifiers (ISD8102/ISD8104) |
Guia de Configuração de Pinos do ISD8104RYI 8-sop with thermal pad (ryi)
Configuração de pinos para ISD8104RYI (pacote 8-sop with thermal pad (ryi)). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para ISD8104RYI.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
ISD8104RYI é adequado para 6 aplicaçãos: Doorbell and Intercom Systems, Industrial Alarm Sounders, Appliance Voice Prompt Systems, Toys and Battery-Powered Novelties, Security and Surveillance Audio Alerting, Test and Measurement Audio Indicators.
Doorbell and Intercom Systems
The ISD8104RYI fits doorbell and intercom products because its 2W mono Class AB output is sufficient to drive a small loudspeaker at clear voice-announcement levels in a typical home or office entryway, while its differential input pair rejects hum and noise picked up along wiring runs from the voice IC or microphone front end. In a typical topology, a voice playback IC or codec line output drives the differential inputs, the chip enable pin is driven by the doorbell controller MCU so the amplifier draws minimal current between events, and the speaker connects directly to the output. Because the Class AB stage introduces no switching noise, voice intelligibility remains high even with the amplifier mounted near RF receivers or wireless doorbell receivers.
Recomendado
Industrial Alarm Sounders
In industrial alarm and annunciator panels, the ISD8104RYI provides a robust 2W mono output for warning tones and spoken alerts. The differential input pair is valuable in factory environments where long traces or cable assemblies pick up switching noise from motor drives and relays; common-mode rejection keeps the audio path clean. The chip enable pin allows the panel controller to silence the amplifier during idle periods and re-arm it instantly when an alarm condition occurs. Compared with Class D alternatives, the Class AB output generates no EMI that could disturb nearby PLC analog inputs or radio modules, simplifying EMC compliance of the panel. Designers should budget thermal dissipation via the exposed thermal pad and copper pour when the alarm operates continuously at high volume.
Recomendado
Appliance Voice Prompt Systems
White goods and small appliances increasingly use spoken prompts for cycle status and fault reporting. The ISD8104RYI suits these designs because its 2W output fills a typical kitchen-level acoustic environment, and its low component count - gain-setting resistors plus input/output coupling - keeps BOM cost low in consumer products. The chip enable input ties naturally into appliance MCU GPIO, muting the amplifier outside prompt events to eliminate residual hiss through the speaker grille. The differential input configuration also helps when the audio source is a low-cost DAC output subject to ground bounce from motor and heater switching. Place the amplifier close to the speaker connector and keep the differential input traces short and routed together for best common-mode rejection.
Recomendado
Toys and Battery-Powered Novelties
Battery-operated toys and novelty products need loud, clear audio from a low-cost, low-parts-count amplifier. The ISD8104RYI's 2W mono Class AB stage drives small 8-ohm speakers with low distortion at voice and music levels, and the chip enable pin ensures the amplifier does not drain batteries between playbacks - critical for shelf life. The Class AB topology avoids the cost and board area of the LC output filter that a Class D stage would require in EMI-sensitive toys containing radios or IR links. Its 8-SOP footprint is hand-solderable for low-volume toy production and reflow-compatible for volume lines. Verify supply voltage range against the battery chemistry in the Nuvoton datasheet electrical characteristics table.
Recomendado
Security and Surveillance Audio Alerting
Security panels, cameras with siren functions, and video doorphones use the ISD8104RYI to produce 2W of mono alarm or two-way audio output. The differential input pair helps when the audio source sits on the same board as switching power supplies and digital processors, suppressing common-mode interference. The chip enable control lets the security MCU keep the amplifier silent during armed-standby, avoiding any audible giveaway of the device's presence, then enable it instantly on siren activation. Because Class AB operation creates no switching spurs, it will not interfere with 2.4 GHz wireless links commonly integrated in security devices. Thermal pad soldering to a ground pour is recommended for sustained siren operation.
Recomendado
Test and Measurement Audio Indicators
Bench instruments, handheld meters, and diagnostic tools use short audio prompts or alarm tones, and the ISD8104RYI provides a simple 2W mono path from a controller DAC or tone generator to an internal speaker. The differential input pair rejects digital ground noise from the instrument's processor section, keeping prompts free of clock-hash artifacts that single-ended inputs can pick up. The chip enable input allows firmware to mute audio during measurement capture, preventing acoustic feedback into sensitive transducers. The low external component count and 8-SOP footprint fit compact handheld enclosures, and Class AB linearity preserves waveform fidelity for instruments that must reproduce specific alert tone signatures defined by safety standards.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para ISD8104RYI — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | ISD8104SYI | ISD8102SYI |
|---|---|---|---|
| Package | 8-SOP with thermal pad (RYI) | 8-SOP (with thermal pad) | 8-SOP (with thermal pad) |
| Brand | Nuvoton Technology | Nuvoton Technology | Nuvoton Technology |
| Output Power | 2 W | 2 W | 2 W |
| Amplifier Class | Class AB | Class AB | Class AB |
| Input Configuration | Differential input pair | Differential input pair | Earphone-sense SE/Diff input |
| Channels | 1 (Mono) | 1 (Mono) | 1 (Mono) |
| Chip Enable | Yes | Yes | Yes |
Principais diferenciais
- Dedicated differential input pair for superior noise rejection (vs ISD8102SYI)
- Identical die available as widely-stocked SYI variant (vs ISD8104SYI)
- Class AB linearity with no output filter requirement (vs Generic Class D amplifiers)
Notas de projeto
The ISD8104RYI is a Class AB amplifier, so power dissipation scales with output level and supply voltage; at full 2W output a meaningful fraction of the supply power is dissipated as heat in the die. Solder the exposed thermal pad to a continuous ground copper pour with multiple thermal vias to spread heat into inner layers. For continuous-tone alarm applications, verify junction temperature against the datasheet theta-JA using your enclosure's ambient conditions. Estimated: dissipation must be calculated from actual VIN, load impedance, and duty cycle per the datasheet formulas - do not assume worst case continuously at 2W.
Route the differential input traces as a tightly coupled pair (equal length, close spacing) from the source to the IN+ and IN- pins; the common-mode rejection advantage of the ISD8104's differential pair is only realized when both traces pick up equal noise. Keep gain-setting resistors close to the input pins and use precision values to control gain accuracy. Place the input coupling and supply decoupling capacitors near the IC, and keep the high-current speaker output loop away from the input traces to prevent feedback oscillation.
Do not confuse the ISD8104 with the ISD8102: the 8104 has a dedicated differential input pair while the 8102 has an earphone-sense SE/Diff input, and their input pin functions differ even though both share 2W Class AB output stages and 8-SOP packages. Substituting one for the other without checking the pinout in the Nuvoton combined datasheet can result in a silent or distorted channel. Also confirm enable-pin logic level and startup pop behavior with your MCU drive circuit before locking the design.
Informações de conformidade
Compliance status not stated in the provided web data; confirm RoHS/REACH status on the official Nuvoton product page before procurement.
