LM201ADG - Single 10 V/us Op Amp in 8-SOIC | onsemi
N.º da peça: LM201ADG ✓ AtivoLM201ADG Visão geral
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its inverting and non-inverting inputs. The LM201 belongs to the broader operational-amplifier, linear-amplifier, analog-IC, and semiconductor hierarchies. Unlike a unity-gain-stable op amp, the LM201 is non-compensated, so its closed-loop behavior depends on the external compensation network, feedback topology, load, and desired gain.
Principal features include a 10 V/us slew rate, a Class AB output stage, external frequency compensation, and low input bias and offset current. These characteristics make the device useful when conventional internally compensated amplifiers do not provide enough speed or flexibility. Users can tailor the compensation capacitor to optimize stability and bandwidth for a particular amplifier gain.
The LM201ADG operates from 5 V to 20 V, allowing use with conventional single supplies or dual supplies derived from split rails. Its non-inverting and inverting inputs support standard feedback arrangements, while the output stage drives external compensation networks and downstream analog stages. Because stability is intentionally user-configured, the selected compensation value and closed-loop gain must be evaluated together rather than treated as an independent component choice.
Typical applications include instrumentation signal conditioning, active filtering, summing and difference amplifiers, analog control loops, sensor interfaces, and general-purpose laboratory electronics. The device is especially suitable for designs where adjustable compensation provides a better bandwidth-versus-stability balance than a fixed-compensation amplifier.
The primary design consideration is stability. Check the required gain, load capacitance, output current, supply voltage, and recommended compensation value before finalizing the feedback network. Keep the compensation and feedback components close to the amplifier pins, provide adequate supply bypassing, and avoid long PCB traces that can add parasitic capacitance and alter closed-loop response.
This product page combines the LM201ADG electrical identity with practical compensation guidance, pin information, verified source links, and a selection-focused comparison against documented substitute parts. It is intended to help engineers identify the correct package, confirm replacement compatibility, and plan a stable implementation before placing the component into production.
Alternativas drop-in para LM201ADG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM201ADG (mesmo formato e footprint) — diferindo em Slew Rate, Supply Voltage Range, Package, Number of Amplifiers, Gain-Bandwidth Product.
LM201ADT
✅ Drop-InConsulte o preço
Ver ficha técnica →LM201AVDR2G
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM318MX/NOPB
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
AD548JRZ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
INA154UA
✅ Drop-InConsulte o preço
Ver ficha técnica →LM201ADG Classificações máximas e características elétricas
| Amplifier Type | Single general-purpose operational amplifier |
| Number of Amplifiers | 1 amplifier |
| Compensation Type | Non-compensated with external frequency compensation |
| Supply Voltage Range | 5 V to 20 V |
| Maximum Supply Voltage | 20 V |
| Slew Rate | 10 V/us with proper compensation |
| Output Stage | Class AB |
| Faixa de temperatura de operação | -25 C to +85 C |
| Encapsulamento | 8-SOIC |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Surface mount |
| Status RoHS | unknown |
| REACH Status | unknown |
| Automotive Qualification | unknown |
Configuração de pinos do LM201ADG
| Pino 1 | OFFSET NULL — Offset-voltage adjustment terminal |
| Pino 2 | IN- — Inverting input |
| Pino 3 | IN+ — Non-inverting input |
| Pino 4 | V- — Negative supply connection |
| Pino 5 | OFFSET NULL — Offset-voltage adjustment terminal |
| Pino 6 | OUTPUT — Amplifier output |
| Pino 7 | V+ — Positive supply connection |
| Pino 8 | COMPENSATION — External frequency-compensation connection |
Aplicações típicas
LM201ADG é adequado para 6 aplicaçãos: Active Filtering, Instrumentation Signal Conditioning, Analog Control Loops, Summing and Difference Amplifiers, Laboratory and Test Signal Sources, Sensors and Industrial Controls.
Active Filtering
The onsemi LM201ADG is useful in active-filter stages where the closed-loop gain and compensation can be selected together. Its non-compensated architecture lets the designer choose an external compensation capacitor for the desired stability and bandwidth, while its 10 V/us slew-rate capability supports signals that change rapidly within the filter. In a low-pass or high-pass stage, route the feedback network and compensation capacitor close to the 8-SOIC pins, verify the noise gain at every frequency, and check output loading against the Class AB output stage before fixing the component values.
Recomendado
Instrumentation Signal Conditioning
The LM201ADG can condition low-level sensor signals when its input bias current, offset behavior, and external compensation meet the source requirements. The single-amplifier 8-SOIC configuration saves board area compared with a multi-amplifier package, while the 5 V to 20 V supply range supports several common analog rails. Use the LM201ADG around medium-impedance sensors, amplifiers, or transducers and evaluate source impedance, input common-mode range, output swing, and stability for the selected gain before releasing the schematic.
Recomendado
Analog Control Loops
The LM201ADG fits analog control and feedback paths that benefit from user-selected frequency compensation. Its externally compensated architecture allows the design to trade bandwidth for stability according to the loop gain, while the 10 V/us rated slew rate with proper compensation can respond to control-loop corrections without excessive delay. Place the compensation and feedback parts adjacent to the SOIC pins, decouple the supply rails locally, and verify loop phase margin across temperature, load, and component tolerance rather than relying on nominal gain alone.
Recomendado
Summing and Difference Amplifiers
A non-inverting summing amplifier or differential amplifier can use the LM201ADG when its external compensation is designed for the closed-loop gain and load. The single amplifier in an 8-SOIC package is particularly useful when multiple independent channels are distributed across a board, because each channel can occupy one compact package. Balance the resistor network to preserve common-mode rejection, keep sensitive summing nodes short, and test stability with the actual source impedance and load because parasitic capacitance can change the compensation requirement.
Recomendado
Laboratory and Test Signal Sources
The LM201ADG is appropriate for laboratory signal-conditioning and test circuits where an engineer wants compensation flexibility rather than fixed unity-gain behavior. Its 10 V/us slew rate with proper compensation and 5 V to 20 V supply range allow it to process low-frequency and moderately fast test signals without using a large multi-amplifier package. Validate output swing into the intended load, include local supply bypassing, and reproduce the compensation calculation in simulation before adjusting the capacitor value on the bench.
Recomendado
Sensors and Industrial Controls
The LM201ADG can serve as the gain stage in industrial sensing and control electronics when its operating temperature and compensation requirements suit the installation. The single-amplifier 8-SOIC package supports compact analog boards, and the wide 5 V to 20 V supply range accommodates many legacy control voltages. For industrial use, check temperature-grade markings, transient exposure, noise behavior, and failure-mode expectations. Keep high-impedance sensor traces short and shield them from switching nodes to prevent additional errors from appearing at the amplifier input.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM201ADG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM201ADT | LM201AVDR2G | LM318MX/NOPB | AD548JRZ | INA154UA |
|---|---|---|---|---|---|---|
| Package | 8-SOIC | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same | 8-SOIC - same |
| Brand | onsemi | onsemi | onsemi | onsemi | Analog Devices | Texas Instruments |
| Amplifier Count | 1 amplifier | 1 amplifier | 1 amplifier | 1 amplifier | 1 amplifier | 1 instrumentation amplifier |
| Primary Function | General-purpose non-compensated operational amplifier | General-purpose non-compensated operational amplifier | General-purpose non-compensated operational amplifier | General-purpose single operational amplifier | Precision operational amplifier | Instrumentation amplifier |
Principais diferenciais
- User-selectable frequency compensation (vs AD548JRZ)
- Wider industrial temperature option in the same family (vs LM201ADG)
- Close architectural match for replacements (vs LM318MX/NOPB)
Notas de projeto
Do not treat LM201ADG as a unity-gain-stable amplifier. Select the external compensation capacitor using the intended closed-loop gain, load, supply, and desired bandwidth, then verify stability across component tolerance. A compensation value that works at one gain may not be optimal at another, and excessive compensation can unnecessarily reduce usable bandwidth.
Place the compensation capacitor and feedback components immediately beside the LM201ADG pins, and keep the non-inverting input and sensitive summing-node routes short. Extra PCB capacitance can change the effective compensation value and closed-loop response. Maintain a compact ground return around the analog section and connect the bypass capacitor directly to the relevant supply pins.
Decouple the LM201ADG supply rails with local ceramic capacitance and follow the manufacturer recommendation for bulk or additional bypass capacitance. Keep switching-regulator outputs and high-current return paths away from the input and compensation nodes. Because the amplifier accepts 5 V to 20 V, verify rail startup, transients, and output headroom across the full operating range.
Check output swing, load current, source impedance, and input common-mode limits before using the full supply range. The offset-null terminals are for adjustment and should not be used as signal inputs. When replacing LM201ADG, verify the compensation terminal, offset-null arrangement, gain stability, and operating-temperature grade rather than relying on the 8-SOIC outline alone.
Informações de conformidade
No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement was identified for LM201ADG in the cited product information.