MAX3243EEAI+TG1Z - 3.0V RS-232 Transceiver | Analog Devices
N.º da peça: MAX3243EEAI+TG1Z ✓ AtivoMAX3243EEAI+TG1Z Visão geral
An RS-232 transceiver is an interface IC that converts logic-level signals into RS-232 voltage levels and converts received RS-232 signals back into logic-level signals. The MAX3243E family combines multiple driver and receiver channels with low-power management features, allowing a system to reduce current consumption when the communication port is inactive. Its automatic shutdown and wake-up behavior helps simplify firmware and power-management design in portable and industrial equipment.
Key features of the MAX3243EEAI+TG1Z include 250 kbps maximum data rate, 3.0V to 5.5V supply operation, ±15 kV ESD protection on the RS-232 lines, and a low-power shutdown mode with a typical shutdown supply current of 1 uA as identified by the distributor product listing. The 28-SSOP package provides a conventional surface-mount footprint for RS-232 ports in instruments, computers, industrial controllers, and communication equipment.
The MAX3243EEAI+TG1Z is appropriate when a system needs multiple RS-232 channels but does not require the newer MAX3243EEUI+T variant's alternative package or temperature/qualification positioning. The transmitter outputs include slew-rate control for reduced electromagnetic interference, while the receivers are designed to tolerate RS-232 signal levels encountered in industrial environments. Designers should confirm the exact pin arrangement and signal names in the manufacturer datasheet before finalizing a PCB footprint.
Common applications include industrial serial-port equipment, test and measurement instruments, data-collection systems, point-of-sale terminals, and embedded serial controllers. In each case, the device can operate directly from a 3.3V or 5V system rail while maintaining compatibility with external RS-232 equipment. The ±15 kV ESD rating adds useful protection for exposed connector paths, although external protection and layout practices remain important.
For new layouts, place the transceiver close to the RS-232 connector, route each signal to its intended driver or receiver pin, and keep high-voltage RS-232 traces away from sensitive analog and high-speed digital circuitry. Decoupling capacitors should be placed near the supply pins, and the unused input pins should be tied to a defined logic level according to the datasheet. This page combines manufacturer product information, distributor listings, package guidance, replacement options, and design-focused selection criteria for engineers evaluating this RS-232 interface device.
Alternativas drop-in para MAX3243EEAI+TG1Z — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX3243EEAI+TG1Z (mesmo formato e footprint) — diferindo em ESD Protection, Product Type, Supply Voltage Range, Package, Communication Standard.
MAX3243EEUI+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3243CAI+TG1Z
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3243EEAI
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX3243EEUI+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3243CAI+TG1Z
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3243EEAI+TG1Z Especificações
| Product Type | 3/5 RS-232 transceiver |
| Driver Count | 3 drivers |
| Receiver Count | 5 receivers |
| Supply Voltage Range | 3.0 V to 5.5 V |
| Maximum Data Rate | 250 kbps |
| ESD Protection | +/-15 kV |
| Shutdown Supply Current | 1 uA typical |
| Communication Standard | EIA/TIA-232, V.28, V.24 |
| Automatic Shutdown | Supported |
| Automatic Wake-Up | Supported |
| Encapsulamento | 28-pin SSOP |
| Tipo de montagem | Surface Mount |
| Transmitter Output Protection | Enhanced electrostatic-discharge protection |
| Receiver Configuration | 5 receivers |
Guia de Configuração de Pinos do MAX3243EEAI+TG1Z 28-pin ssop
Configuração de pinos para MAX3243EEAI+TG1Z (pacote 28-pin ssop). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX3243EEAI+TG1Z.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX3243EEAI+TG1Z é adequado para 6 aplicaçãos: Industrial Serial-Control Equipment, Test and Measurement Instruments, Data-Collection and Gateway Systems, Point-of-Sale and Peripheral Interfaces, Embedded Serial Controllers, Communications and Service Equipment.
Industrial Serial-Control Equipment
The MAX3243EEAI+TG1Z fits industrial controllers that need several RS-232 ports for service consoles, sensors, and legacy machinery. Its three drivers and five receivers provide flexible channel allocation, while 3.0V to 5.5V operation supports common industrial logic rails. The 250 kbps maximum data rate accommodates configuration and status traffic. Automatic shutdown helps reduce power when a port is unused, and ±15 kV ESD protection adds margin around exposed connector circuits, although site-specific EMC and surge requirements still need verification.
Recomendado
Test and Measurement Instruments
Use the MAX3243EEAI+TG1Z in instruments that exchange commands and measurement data through RS-232. The 250 kbps data rate supports practical instrument-control traffic, while the three-driver and five-receiver arrangement allows one controller to connect to multiple peripherals or combine separate receive paths. The device can run from 3.3V or 5V logic, reducing power-supply complexity. Place it near the DB9 or equivalent connector and verify grounding, cable length, and ESD layout for bench and field use.
Recomendado
Data-Collection and Gateway Systems
The MAX3243EEAI+TG1Z is appropriate for gateways that collect data from RS-232 meters, barcode systems, or laboratory instruments. Multiple receivers allow the gateway to monitor several device status lines, while three drivers support command and data connections. Automatic shutdown and wake-up are useful for systems that spend substantial time between polling cycles. The device does not provide galvanic isolation, so long cable runs, ground-potential differences, and lightning exposure may require external protection and isolation components.
Recomendado
Point-of-Sale and Peripheral Interfaces
The MAX3243EEAI+TG1Z can interface a controller or embedded system with RS-232 printers, scanners, and payment peripherals that retain legacy serial ports. Its compact 28-SSOP package leaves board space for the rest of the product, and the 3.0V to 5.5V range supports both 3.3V and 5V system architectures. The 1 uA typical shutdown current is useful for reducing idle consumption. Confirm connector signaling, cable length, and peripheral timing because those requirements determine whether the 250 kbps capability is adequate.
Recomendado
Embedded Serial Controllers
The MAX3243EEAI+TG1Z suits embedded controllers that must bridge a processor UART to external RS-232 equipment. It consolidates three transmit and five receive channels into one IC, reducing board area and simplifying firmware resource allocation. Automatic wake-up allows the system to react to incoming serial activity while reducing standby consumption, and the broad 3.0V to 5.5V supply range accommodates common embedded platforms. Firmware should treat automatic wake-up as a hardware aid and still validate framing, timeout, and connector-state conditions.
Recomendado
Communications and Service Equipment
The MAX3243EEAI+TG1Z supports service and communications equipment that maintains legacy RS-232 management ports alongside newer embedded interfaces. Five receivers can monitor multiple incoming lines, while three drivers provide outbound control and data channels. Its 250 kbps rate is sufficient for many management and diagnostic protocols, while ±15 kV ESD protection improves resilience at connector-exposed pins. The design still needs a careful ground-return strategy and appropriate protection for cables leaving the enclosure.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX3243EEAI+TG1Z — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX3243EEUI+T | MAX3243CAI+TG1Z | MAX3243EEAI | MAX3243EEUI+T | MAX3243CAI+TG1Z |
|---|---|---|---|---|---|---|
| Package | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP | 28-pin SSOP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
Principais diferenciais
- Three drivers and five receivers in one 28-SSOP device (vs MAX3243EEAI)
- Automatic shutdown and wake-up support (vs MAX3243CAI+TG1Z)
- 250 kbps operation with ±15 kV ESD protection (vs MAX3243EEUI+T)
Notas de projeto
Place the MAX3243EEAI+TG1Z close to the RS-232 connector and keep the RS-232 traces short. Route the transceiver-side nets according to the manufacturer datasheet pin descriptions, and provide local supply bypassing between the supply and ground pins. Avoid placing the connector, protection devices, and transceiver in separate ground regions when a common chassis or signal-ground strategy is required.
RS-232 driver edges can radiate EMI even when the logic-side clock is slow. Preserve the manufacturer-recommended charge-pump capacitor and output-slew-rate layout, keep the supply and ground connections compact, and avoid long stubs on driver and receiver nets. For cables leaving an enclosure, combine the IC's internal ESD protection with an appropriately rated external protection network.
Do not assume that all MAX3243-family suffixes are automatically interchangeable. Verify the exact ordering code, temperature grade, lead configuration, package drawing, pin names, and qualification requirements before substituting a part. Also confirm that the host system does not expect RS-232 signal polarity or handshake behavior that differs from the selected family member.
Use the manufacturer's recommended charge-pump capacitor values and account for their voltage and tolerance requirements when designing the supply network. The automatic shutdown function can reduce average current, but the data sheet's operating conditions still govern the maximum supply and signal amplitudes. Validate the power budget over startup, active transmission, idle wake-up detection, and shutdown transitions.
Informações de conformidade
The manufacturer page confirms the MAX3243E family and its 3V-powered RS-232 communications-interface role, but the verified product snippets do not provide complete compliance statements for the exact ordering suffix. Confirm RoHS, REACH, lead-free, halogen-free, and conflict-minerals status using the manufacturer product documentation or material declaration before release.