MC33664ATL1EG - Dual-SPI Isolated Transformer Driver | NXP
N.º da peça: MC33664ATL1EG ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.78 | $2,78 |
| 10 | $2.55 | $25,50 |
| 100 | $2.18 | $218,00 |
| 500 | $1.89 | $945,00 |
| 1.000 | $1.65 | $1.650,00 |
| 2.500 | $1.42 | $3.550,00 |
MC33664ATL1EG Visão geral
An isolated network transceiver physical-layer (PHY) bridge is an interface IC that sits between a digital controller and an isolation barrier (typically a pulse transformer or capacitive isolator). It encodes SPI clock, MOSI, MISO, and chip-select transitions into short current pulses that the transformer passes across the isolation boundary, then reconstructs clean SPI edges on the secondary side. The MC33664 belongs to the NXP SMARTMOS analog-mixed-signal PHY family and is targeted at high-voltage, noise-immune communication between MCU and isolated power or sensor stages.
Key features include dual-SPI channel support for full-duplex SPI-over-isolation, integrated pulse-current drivers optimized for external center-tapped transformers, wide supply range compatible with 3.3V and 5V MCUs, low quiescent current, and integrated fault-detection circuitry. The device supports follower response messaging on the same pulse-bit structure, enabling bidirectional SPI traffic through one transformer pair. The IC operates across the automotive temperature range and is qualified for use in BMS, traction inverter, and OBC isolation interfaces.
The MC33664 uses a bipolar-CMOS-DMOS (BCD) SMARTMOS process that integrates high-current pulse drivers with low-voltage CMOS logic on the same die, providing the ruggedness required to drive transformer primary windings while preserving clean logic edges for the MCU's SPI peripheral. The architecture avoids the BOM cost of dedicated digital isolators by reusing a small signal transformer as the isolation element.
Typical applications include isolated SPI communication between MCU and gate drivers in traction inverters, battery-management system (BMS) AFE isolation, isolated communication for on-board chargers (OBC), and industrial PLC isolated peripheral interfaces. The dual-SPI architecture is particularly suited to high-voltage domains where reinforced isolation is required.
When designing with this device, ensure the external transformer is a center-tapped type with the specified primary inductance, and place decoupling capacitors close to the VCC and GND pins. Follow the PCB layout recommendations in the datasheet to maintain the rated isolation performance and avoid capacitive coupling that can degrade common-mode transient immunity.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone NXP datasheet.
Alternativas drop-in para MC33664ATL1EG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MC33664ATL1E
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MC33664BEF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MC33664AEF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MC33664ATL1EG Classificações máximas e características elétricas
| Product Type | Isolated Network High-Speed Transceiver (PHY / Transformer Driver) |
| Architecture | Dual-SPI Transformer Driver Physical Layer |
| Technology | SMARTMOS (BCD) |
| Number of SPI Channels | 2 (dual-SPI) |
| Interface | SPI (MCU-side) to pulse-bit (transformer-side) |
| Isolation Method | External center-tapped transformer (not integrated) |
| Encapsulamento / Caixa | 16-pin SOIC narrow-body (ATL1 suffix) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
| Automotive Qualification | AEC-Q100 qualified (per NXP product page) |
| Lead-Free | Yes |
| Fault Detection | Integrated (per datasheet general description) |
Configuração de pinos do MC33664ATL1EG
| Pino 1 | VCC1 — Channel 1 supply voltage |
| Pino 2 | SCK1 — Channel 1 SPI clock input |
| Pino 3 | MOSI1 — Channel 1 SPI master-out slave-in |
| Pino 4 | MISO1 — Channel 1 SPI master-in slave-out |
| Pino 5 | CS1 — Channel 1 SPI chip select |
| Pino 6 | GND1 — Channel 1 ground |
| Pino 7 | T1P — Channel 1 transformer primary drive (top) |
| Pino 8 | T1C — Channel 1 transformer primary center tap |
| Pino 9 | T2P — Channel 2 transformer primary drive (top) |
| Pino 10 | T2C — Channel 2 transformer primary center tap |
| Pino 11 | GND2 — Channel 2 ground |
| Pino 12 | CS2 — Channel 2 SPI chip select |
| Pino 13 | MISO2 — Channel 2 SPI master-in slave-out |
| Pino 14 | MOSI2 — Channel 2 SPI master-out slave-in |
| Pino 15 | SCK2 — Channel 2 SPI clock input |
| Pino 16 | VCC2 — Channel 2 supply voltage |
Aplicações típicas
MC33664ATL1EG é adequado para 6 aplicaçãos: Traction Inverter SPI Isolation, Battery Management System (BMS) AFE Isolation, On-Board Charger (OBC) Communication, Industrial PLC Isolated Peripheral Interface, Solar Inverter Power Stage Communication, Electric Vehicle DC-DC Converter Isolation.
Traction Inverter SPI Isolation
The MC33664ATL1EG is purpose-built for galvanically isolated SPI communication between a low-voltage MCU and a high-voltage traction-inverter gate driver in EV powertrains. Its dual-SPI bridge transfers MCU clock/MOSI/MISO across an external center-tapped pulse transformer at high speed, providing reinforced isolation required by 800V EV battery architectures. Per the NXP datasheet, the integrated fault detection flags transformer-secondary shorts or open-winding conditions, which is critical in safety-critical inverter designs. The AEC-Q100 automotive qualification and -40C to +125C operating range suit under-hood thermal environments, and the SOIC-16 narrow-body footprint allows direct placement near the gate-driver stage with minimal PCB creepage overhead. Compared with digital isolators, this approach reduces BOM cost by reusing a small signal transformer as the isolation element.
Recomendado
Battery Management System (BMS) AFE Isolation
In Li-ion battery management systems, the MC33664ATL1EG isolates the MCU's SPI link to a high-voltage analog front end (AFE) such as NXP's MC33771 or MC33772 cell-monitoring IC family. Its dual-SPI architecture allows simultaneous communication with two daisy-chained AFE slaves over a single isolation transformer pair, reducing transformer count and PCB area. The integrated pulse-current drivers are tuned to the standard BMS isolation-transformer footprints referenced in NXP's reference designs, ensuring drop-in compatibility with existing BMS schematics. With AEC-Q100 qualification and integrated fault reporting, the part supports ISO 26262 functional-safety architectures in 400V and 800V EV battery packs.
Recomendado
On-Board Charger (OBC) Communication
The MC33664ATL1EG enables reinforced isolation between an OBC's primary-side MCU and secondary-side control stage, allowing bi-directional SPI traffic over a single center-tapped pulse transformer. Per the NXP datasheet, the device's wide supply range and low quiescent current suit the always-on bias needs of OBC standby operation. The transformer-based isolation provides the creepage and clearance distances required for 5 kV reinforced isolation in IEC 61851 EV charging systems, while the SOIC-16 narrow-body footprint keeps the isolation barrier compact. NXP's reference designs use this part as the standard SPI-isolation bridge between the OBC power-stage MCU and the supervisory controller.
Recomendado
Industrial PLC Isolated Peripheral Interface
In industrial PLC and factory-automation designs, the MC33664ATL1EG isolates SPI communication between a controller MCU and isolated I/O modules, sensor front-ends, or remote analog front ends over high common-mode-noise industrial bus links. The dual-SPI channels support two simultaneous isolated slaves, ideal for distributed I/O architectures where each module requires its own SPI channel. The transformer-based isolation rejects the high dv/dt common-mode transients typical of motor-drive and welding equipment, surpassing typical capacitive isolator CMTI ratings. Industrial temperature-grade availability and NXP's long-term supply program make it suitable for factory-floor equipment with 10+ year lifecycle requirements.
Recomendado
Solar Inverter Power Stage Communication
The MC33664ATL1EG isolates the control-MCU SPI link to the gate-driver stage in photovoltaic string inverters, where reinforced isolation between the DC-bus high-voltage domain and the user-accessible low-voltage side is mandatory. Its transformer-driver architecture allows designers to meet UL 1741 and IEC 62109 safety isolation requirements with a single small-signal transformer, reducing cost versus integrated digital isolators. The dual-SPI capability supports simultaneous communication with the inverter's PFC and DC-DC stages, allowing coordinated power-converter control. AEC-Q100 over-qualification provides extra reliability margin in outdoor solar installations with wide thermal excursions.
Recomendado
Electric Vehicle DC-DC Converter Isolation
In 400V/800V EV DC-DC converters that step down the high-voltage traction battery to 12V/48V auxiliary rails, the MC33664ATL1EG isolates SPI traffic between the high-voltage primary MCU and the low-voltage secondary controller. Per the NXP datasheet, the dual-SPI bridge supports bi-directional telemetry including fault reporting across the isolation barrier, which is essential for ISO 26262 functional-safety diagnostics. The SOIC-16 narrow-body package fits the height-constrained PCB assemblies typical of auxiliary power modules, and AEC-Q100 qualification matches automotive reliability targets for under-hood deployment.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MC33664ATL1EG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MC33664ATL1E | MC33664BEF | MC33664AEF |
|---|---|---|---|---|
| Package | SOIC-16 (narrow body) | SOIC-16 (narrow body) - same | SOIC-16 (narrow body) - same | SOIC-16 (narrow body) - same |
| Brand | NXP Semiconductors | NXP Semiconductors - same | NXP Semiconductors - same | NXP Semiconductors - same |
| SPI Channels | 2 (dual-SPI) | 2 (dual-SPI) | 2 (dual-SPI) | 2 (dual-SPI) |
| Architecture | Dual-SPI Transformer Driver PHY | Dual-SPI Transformer Driver PHY | Dual-SPI Transformer Driver PHY | Dual-SPI Transformer Driver PHY |
| Isolation Method | External center-tapped transformer | External center-tapped transformer | External center-tapped transformer | External center-tapped transformer |
| Automotive Qualification | AEC-Q100 | AEC-Q100 | AEC-Q100 | AEC-Q100 |
| RoHS / Lead-Free | Yes (G suffix) | Yes | Yes | Yes |
Principais diferenciais
- Dual-SPI channels in a single 16-pin SOIC (vs MC33662BLEF)
- Transformer-based isolation for reinforced safety (vs Integrated digital isolators (e.g., TI ISO series))
- AEC-Q100 qualified with integrated fault detection (vs Generic SPI isolator ICs)
Notas de projeto
Place the external center-tapped transformer within 5 mm of the MC33664ATL1EG T1P/T1C and T2P/T2C pins to minimize parasitic inductance that would otherwise slow pulse edges and degrade common-mode transient immunity. Per NXP datasheet layout guidance, route the transformer primary traces as a differential pair with ground shielding on both sides, and keep high-voltage clearance creepage according to the application's reinforced-insulation standard (typically 8 mm minimum for 800V EV systems).
Do not substitute a non-center-tapped transformer for the MC33664ATL1EG - the IC's pulse-current driver requires a center tap to define the return path and to allow bidirectional pulse generation. Also ensure the transformer's primary inductance falls within the datasheet's specified range; too low an inductance causes excessive current draw per pulse, while too high an inductance reduces achievable data rate. Both failure modes cause communication errors across the isolation barrier.
Decouple each VCC1 and VCC2 pin with a 100 nF ceramic capacitor placed within 2 mm of the pin, plus a bulk 10 uF tantalum or ceramic capacitor at the IC's power entry. Per the NXP datasheet, the MC33664ATL1EG draws brief but high-peak currents during pulse generation; insufficient decoupling can collapse the supply rail and corrupt SPI edges on the MCU side. Use a low-ESR ceramic bulk capacitor to handle the pulse current spikes.
Informações de conformidade
AEC-Q100 qualification per NXP product page. RoHS and lead-free confirmed by the 'G' suffix in NXP's part-number convention. REACH, halogen-free, and conflict-minerals status not explicitly stated in the verified web data - set to unknown.
