MC9S08RC32FJ - 8-Bit 8MHz 32KB Flash MCU | NXP
N.º da peça: MC9S08RC32FJ ✓ AtivoMC9S08RC32FJ Visão geral
A microcontroller is a programmable semiconductor that integrates a processor core, program memory, data memory, and peripherals into one device. The S08 architecture belongs to the broader category of 8-bit embedded microcontrollers, which are commonly used for control, sensing, and actuator-management tasks. At 8 MHz, the MC9S08RC32FJ provides deterministic processing capability for products where a low-cost, low-power controller is preferable to a more complex application processor.
The MC9S08RC32FJ combines 32 KB of flash memory with an 8 MHz operating frequency in a 32-LQFP package. The 1.8 V to 3.6 V operating range supports direct operation from common low-voltage rails, while the 7 mm by 7 mm package provides a surface-mount solution for compact assemblies. Its 32-terminal gull-wing package also exposes more interface connections than a smaller 20-pin controller package, supporting practical external sensing, communications, and control connections.
This commercial-temperature S08 microcontroller is positioned for embedded control designs that require an established 8-bit architecture and an adequate balance of flash memory, processing speed, and package size. The 32 KB program-memory capacity can hold application firmware, configuration logic, and control routines. Because the device is identified as an 8-bit MCU, software timing and interrupt handling should be evaluated against the workload rather than compared directly with 16-bit or 32-bit processors.
Typical uses include small motor and relay controllers, building-control interfaces, appliance control panels, industrial sensing nodes, and compact consumer products. Its 8 MHz operating speed is appropriate for supervisory control loops, button and sensor management, status indication, and communications handling. Designs that require substantially more code space, higher processing throughput, or a different pin count should evaluate another MCU in the S08 family or a device from another embedded-controller architecture.
The principal design consideration is ensuring that the LQFP footprint, pin assignment, flash requirement, voltage range, and peripheral configuration match the intended PCB. Use the pin-description table in the manufacturer datasheet when assigning tracks, and confirm the board's exposed thermal and manufacturing requirements before release. Firmware development should also account for the S08 peripheral configuration and memory map used by the selected software toolchain.
This page organizes the available specifications, package information, practical application guidance, and confirmed family alternatives into one engineering reference. It also identifies unsupported electrical, timing, peripheral, and environmental details for verification against the manufacturer datasheet before a production design is released.
Alternativas drop-in para MC9S08RC32FJ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
MC9S08RC32FJE
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MC9S08RC32FJA
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MC9S08RC32FJM
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MC9S08RC32FJ Classificações máximas e características elétricas
| Product Type | 8-bit S08 Flash Microcontroller |
| Frequência máxima de clock | 8 MHz |
| Flash Memory Size | 32 KB |
| Flash Organization | 32K x 8 bits |
| Tensão de alimentação de operação | 1.8 V to 3.6 V |
| Processor Architecture | 8-bit |
| Encapsulamento | 32-LQFP (7 mm x 7 mm) |
| Number of Terminals | 32 |
| Terminal Form | Gull wing |
| Package Shape | Square |
| Package Code | LQFP |
| Temperature Grade | Commercial |
| Tipo de montagem | Surface mount |
| Status RoHS | Compliant |
Guia de Configuração de Pinos do MC9S08RC32FJ lqfp
Configuração de pinos para MC9S08RC32FJ (pacote lqfp). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para MC9S08RC32FJ.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MC9S08RC32FJ é adequado para 6 aplicaçãos: Industrial Sensing and Control Nodes, Appliance and Equipment Controllers, Small Motor and Relay Control, Building Control and Access Interfaces, Portable Consumer Accessories, Communication and Protocol Bridges.
Industrial Sensing and Control Nodes
The MC9S08RC32FJ fits compact sensing nodes that need local acquisition, decision logic, and actuator control without the overhead of a high-performance processor. Its 8-bit S08 core operates at 8 MHz, while 32 KB of flash provides room for firmware that samples sensors, evaluates thresholds, manages status indicators, and controls discrete outputs. The 1.8 V to 3.6 V operating range supports low-voltage designs, and the 32-LQFP package offers ample connections for sensors and I/O. Select the ordering variant whose temperature grade covers the installation environment, and verify all peripheral assignments and timing requirements in the manufacturer datasheet.
Appliance and Equipment Controllers
The MC9S08RC32FJ is appropriate for appliance control boards that coordinate buttons, displays, relays, and safety-related monitoring functions. An 8 MHz S08 processor can manage a real-time control state machine, while 32 KB of flash accommodates application logic and configuration. Its 1.8 V to 3.6 V supply range can simplify integration with 3.3 V system rails, and the 32-LQFP footprint provides enough pins for multiple peripheral functions. Engineers should confirm the selected variant's temperature range, required timers and communication interfaces, reset behavior, and pin multiplexing in the manufacturer documentation.
Small Motor and Relay Control
The MC9S08RC32FJ can serve as the supervisory controller in compact relay, solenoid, or small-motor products. Its 8-bit S08 architecture at 8 MHz is suitable for deterministic command sequencing, input debouncing, current-limit monitoring, and fault-state handling. The 32 KB flash capacity provides space for firmware tables and application logic, while the 32-LQFP package supports external drivers and sensing connections. The device is not a replacement for a power MOSFET or gate driver, so it should operate through the appropriate power stage. Validate timing, pin multiplexing, and environmental grade before production.
Building Control and Access Interfaces
The MC9S08RC32FJ is well suited to compact building-control endpoints that monitor inputs and report status through a low-speed serial interface. The 32 KB flash memory can retain protocol handlers, device identification, event logic, and configuration routines, while the 8 MHz core supports responsive supervisory control. Its low 1.8 V to 3.6 V operating range is compatible with carefully designed 3.3 V power systems, and the 32-LQFP package offers a practical surface-mount footprint. Because environmental requirements vary between installations, confirm the commercial MC9S08RC32FJ or the appropriate broader temperature-grade variant against the product specification.
Portable Consumer Accessories
The MC9S08RC32FJ can support portable accessories that combine a few sensors, LEDs, buttons, and a low-rate communications link. Its 8-bit processing core is appropriate for coordinating simple user interactions rather than intensive graphics or high-bandwidth data processing, while 32 KB flash provides useful application capacity. The 1.8 V to 3.6 V range enables operation from low-voltage energy sources after appropriate regulation, and the 7 mm by 7 mm 32-LQFP package supports compact board construction. Verify average and peak current requirements, clock accuracy, low-power behavior, and all exposed-pin functions before finalizing a battery-powered design.
Communication and Protocol Bridges
The MC9S08RC32FJ is suitable for simple protocol-conversion or embedded interface modules where deterministic 8-bit processing is sufficient. At 8 MHz, the S08 core can manage framing, command parsing, state tracking, and acknowledgments while 32 KB of flash holds application firmware. The 32-LQFP package provides a generous connection count for a communications transceiver, logic interface, status controls, and power supervision. The 1.8 V to 3.6 V operating range must be reconciled with the voltage levels required by the external transceiver. Confirm timer, serial-interface, and port-mapping options in the manufacturer pin-description table.
Dados de referência de engenharia para MC9S08RC32FJ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MC9S08RC32FJE | MC9S08RC32FJA | MC9S08RC32FJM |
|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 32-LQFP (7 mm x 7 mm) | 32-LQFP (7 mm x 7 mm) - same | 32-LQFP (7 mm x 7 mm) - same | 32-LQFP (7 mm x 7 mm) - same |
| Processor Architecture | 8-bit S08 | 8-bit S08 | 8-bit S08 | 8-bit S08 |
| Maximum Clock Frequency | 8 MHz | 8 MHz | 8 MHz | 8 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 32 KB |
| Operating Supply Voltage | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Number of Terminals | 32 | 32 | 32 | 32 |
Principais diferenciais
- Commercial-grade ordering option (vs MC9S08RC32FJE)
- Same core performance across the compared ordering options (vs MC9S08RC32FJA)
- Consistent package and memory architecture (vs MC9S08RC32FJM)
Notas de projeto
Assign the PCB footprint from the 32-LQFP 7 mm by 7 mm package drawing rather than from a generic LQFP library. Confirm pad dimensions, pin-1 orientation, courtyard clearance, solder-mask definition, and the package terminal arrangement against the manufacturer drawing. Maintain unobstructed access around the perimeter for visual inspection and assembly while avoiding nearby tall components that could interfere with reflow or rework.
Design the supply network for the stated 1.8 V to 3.6 V operating range and verify startup, transient response, and brownout behavior in the manufacturer datasheet. Place the local supply and ground bypass capacitors at the device power terminals using the layout and capacitance values recommended by the manufacturer. Avoid routing noisy switching-current paths through the MCU supply branch, and check regulator headroom across temperature and load.
Do not assume that every suffix in the MC9S08RC32 family is interchangeable. Compare the ordering code, temperature grade, memory configuration, clock rating, package, and pin function before substituting one variant for another. Also verify the active reset and programming connections and all multiplexed peripheral assignments in the pin-description table; a shared package does not guarantee identical software configuration.
Keep clock, programming-interface, and sensitive analog or sensing connections away from high-current switching nodes. Use a compact ground return beneath the device and route return currents without creating narrow loops through the MCU area. Where communication or sensor signals leave the board, provide protection and impedance control appropriate to the interface rather than relying only on the MCU's internal protection features.
Informações de conformidade
RoHS compliance is stated by the LCSC product listing. No additional environmental or material-compliance claims are confirmed.