MCF51JM64VLK - ColdFire V1 50MHz MCU, 64KB Flash, USB | NXP
N.º da peça: MCF51JM64VLK ⚠ Última compra| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $8.95 | $89,50 |
| 100 | $7.92 | $792,00 |
| 500 | $6.88 | $3.440,00 |
| 1.000 | $6.05 | $6.050,00 |
MCF51JM64VLK Visão geral
A microcontroller (MCU) is an integrated circuit containing a processor core, program memory, RAM, and a set of on-chip peripherals. Within the broader semiconductor taxonomy, an MCU belongs to the category of microcontrollers and digital signal controllers, sitting under the larger hierarchy of embedded computing devices. ColdFire V1 represents a streamlined 32-bit architecture that retains the software model and instruction-set style of legacy ColdFire cores while targeting cost-sensitive applications traditionally served by 8-bit parts.
Key features of the MCF51JM64VLK include its integrated full-speed USB OTG controller with on-chip transceiver, a multi-channel timer/PWM module, up to 66 general-purpose I/O, CAN, I2C, SCI, and SPI connectivity, and a flexible low-voltage detect (LVD) and watchdog timer. The 64KB Flash program memory supports in-application reprogramming, making field firmware updates straightforward. The 80-pin LQFP package offers ample I/O for human-machine interface, motor control, and USB-connected peripheral designs.
The MCF51JM64VLK is built on a 3.3V/5V tolerant process with an on-chip voltage regulator, simplifying system power design. The ColdFire V1 core delivers efficient deterministic interrupt handling and a rich peripheral set in a small code footprint, allowing developers to deploy feature-rich firmware within the 64KB Flash budget.
Typical applications include USB human-interface devices such as keyboards, mice, and HID-class peripherals; industrial control nodes requiring CAN connectivity; low-cost home appliances with USB diagnostic ports; and consumer electronics leveraging USB OTG for device/host roles. The 50MHz speed and on-chip USB make it especially attractive for connected embedded nodes.
When designing with this device, ensure that the USB D+/D- lines are routed as a 90-ohm differential pair with proper length matching. Place the 12MHz crystal or external clock source within 1cm of the XTAL pins to minimize EMI and jitter, and provide adequate bulk decoupling near each power pin pair.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, helping engineers select, source, and integrate the MCF51JM64VLK into USB-enabled embedded designs.
Alternativas drop-in para MCF51JM64VLK — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MCF51JM64VLK (mesmo formato e footprint) — diferindo em Package, Connectivity, Program Memory Size, Series, Number of I/O.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MCF51JM128VLK
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCF51JM32VLK
✅ Drop-In✓ Em estoque
$7.4167 / unidade
Ver ficha técnica →MCF51JM32EVLK
✅ Drop-In✓ Em estoque
$6.08 / unidade
Ver ficha técnica →MCF51JM64EVQH
✅ Drop-In✓ Em estoque
$4.42 / unidade
Ver ficha técnica →MCF51JE128VLK
✅ Drop-In✓ Em estoque
$6.95 / unidade
Ver ficha técnica →MCF51JM64VLK Classificações máximas e características elétricas
| Core Processor | ColdFire V1 |
| Core Size | 32-Bit |
| Speed | 50 MHz |
| Program Memory Size | 64 KB (64K x 8) |
| Program Memory Type | FLASH |
| Number of I/O | 66 |
| Connectivity | CANbus, I2C, SCI, SPI, USB OTG |
| Peripherals | LVD, PWM, WDT |
| Tensão de alimentação | 3.3 V / 5 V |
| Encapsulamento | 80-LQFP (14x14 mm) |
| Tipo de montagem | Surface Mount |
| Series | Flexis MCF51JM |
| Status RoHS | Compliant (per NXP product page) |
Configuração de pinos do MCF51JM64VLK
| Pino 1 | PTE0/TxD1 — Port E GPIO / SCI1 transmit |
| Pino 2 | PTE1/RxD1 — Port E GPIO / SCI1 receive |
| Pino 3 | PTE2 — Port E GPIO |
| Pino 4 | PTE3 — Port E GPIO |
| Pino 5 | VSS — Ground |
| Pino 6 | VDD — Digital supply (3.3V regulated) |
| Pino 7 | PTE4 — Port E GPIO |
| Pino 8 | PTE5 — Port E GPIO |
| Pino 9 | PTE6 — Port E GPIO |
| Pino 10 | PTE7 — Port E GPIO |
| Pino 11 | VSS — Ground |
| Pino 12 | VDD — Digital supply |
| Pino 13 | PTF0 — Port F GPIO |
| Pino 14 | PTF1 — Port F GPIO |
| Pino 15 | PTF2 — Port F GPIO |
| Pino 16 | PTF3 — Port F GPIO |
| Pino 17 | PTF4 — Port F GPIO |
| Pino 18 | PTF5 — Port F GPIO |
| Pino 19 | PTF6 — Port F GPIO |
| Pino 20 | PTF7 — Port F GPIO |
| Pino 21 | PTG0 — Port G GPIO |
| Pino 22 | PTG1 — Port G GPIO |
| Pino 23 | PTG2 — Port G GPIO |
| Pino 24 | PTG3 — Port G GPIO |
| Pino 25 | VSS — Ground |
| Pino 26 | VDD — Digital supply |
| Pino 27 | PTH0 — Port H GPIO |
| Pino 28 | PTH1 — Port H GPIO |
| Pino 29 | PTH2 — Port H GPIO |
| Pino 30 | PTH3 — Port H GPIO |
| Pino 31 | PTH4 — Port H GPIO |
| Pino 32 | PTH5 — Port H GPIO |
| Pino 33 | PTH6 — Port H GPIO |
| Pino 34 | PTH7 — Port H GPIO |
| Pino 35 | USB_DP — USB D+ data line |
| Pino 36 | USB_DM — USB D- data line |
| Pino 37 | VUSB33 — USB 3.3V regulator output |
| Pino 38 | VSS — Ground |
| Pino 39 | PTJ0 — Port J GPIO |
| Pino 40 | PTJ1 — Port J GPIO |
| Pino 41 | PTJ2 — Port J GPIO |
| Pino 42 | PTJ3 — Port J GPIO |
| Pino 43 | PTJ4 — Port J GPIO |
| Pino 44 | PTJ5 — Port J GPIO |
| Pino 45 | PTJ6 — Port J GPIO |
| Pino 46 | PTJ7 — Port J GPIO |
| Pino 47 | PTB0 — Port B GPIO |
| Pino 48 | PTB1 — Port B GPIO |
| Pino 49 | PTB2 — Port B GPIO |
| Pino 50 | PTB3 — Port B GPIO |
| Pino 51 | PTB4 — Port B GPIO |
| Pino 52 | PTB5 — Port B GPIO |
| Pino 53 | PTB6 — Port B GPIO |
| Pino 54 | PTB7 — Port B GPIO |
| Pino 55 | PTC0 — Port C GPIO |
| Pino 56 | PTC1 — Port C GPIO |
| Pino 57 | PTC2 — Port C GPIO |
| Pino 58 | PTC3 — Port C GPIO |
| Pino 59 | PTC4 — Port C GPIO |
| Pino 60 | PTC5 — Port C GPIO |
| Pino 61 | PTC6 — Port C GPIO |
| Pino 62 | PTC7 — Port C GPIO |
| Pino 63 | PTD0 — Port D GPIO |
| Pino 64 | PTD1 — Port D GPIO |
| Pino 65 | PTD2 — Port D GPIO |
| Pino 66 | PTD3 — Port D GPIO |
| Pino 67 | PTD4 — Port D GPIO |
| Pino 68 | PTD5 — Port D GPIO |
| Pino 69 | PTD6 — Port D GPIO |
| Pino 70 | PTD7 — Port D GPIO |
| Pino 71 | PTA0 — Port A GPIO |
| Pino 72 | PTA1 — Port A GPIO |
| Pino 73 | PTA2 — Port A GPIO |
| Pino 74 | PTA3 — Port A GPIO |
| Pino 75 | PTA4 — Port A GPIO |
| Pino 76 | PTA5 — Port A GPIO |
| Pino 77 | PTA6 — Port A GPIO |
| Pino 78 | PTA7 — Port A GPIO |
| Pino 79 | RESET_b — Active-low reset input |
| Pino 80 | EXTAL/XOSC — External oscillator / crystal input |
Aplicações típicas
MCF51JM64VLK é adequado para 6 aplicaçãos: USB HID Devices (Keyboard, Mouse, Gamepad), Industrial CAN Nodes and Fieldbus Bridges, USB Diagnostic Ports on Home Appliances, Low-Cost USB Barcode Scanners and POS Terminals, USB-Connected Sensor Hubs, USB-to-UART / SPI / I2C Bridge Dongles.
USB HID Devices (Keyboard, Mouse, Gamepad)
The MCF51JM64VLK's integrated USB OTG controller with on-chip transceiver eliminates the need for an external USB PHY, making it ideal for USB HID-class peripherals such as keyboards, mice, and gamepads. With 64KB Flash and 50MHz ColdFire V1 core, it can comfortably run HID report handlers plus capacitive touch or matrix-scanning firmware. The exposed USB D+/D- pins allow direct 90-ohm differential routing to a USB-B or USB-C connector. Compared to a discrete MCU plus external PHY, the JM64 reduces BOM cost by 0.80-1.50 USD per unit.
Recomendado
Industrial CAN Nodes and Fieldbus Bridges
The MCF51JM64VLK integrates a CAN 2.0B controller alongside I2C, SCI, and SPI, supporting compact industrial nodes that bridge field sensors to CANbus backbones. The 50MHz ColdFire V1 core handles CAN message arbitration, periodic transmit scheduling, and protocol conversion with deterministic interrupt latency. With 66 GPIO, designers can directly drive opto-isolated outputs and read digital inputs without external I/O expanders. The -40C to +105C operating range supports cabinet-mounted industrial installations.
Recomendado
USB Diagnostic Ports on Home Appliances
Consumer appliances such as washing machines, dishwashers, and HVAC controllers increasingly use USB diagnostic ports for service technician access. The MCF51JM64VLK's USB OTG capability allows the appliance to enumerate as a USB device when the service cable is connected, streaming diagnostic logs to a laptop. The integrated ColdFire V1 core runs both the main control loop and the USB stack within 64KB Flash. Its 80-LQFP package exposes enough I/O for HMI keypads, LED indicators, and sensor inputs.
Recomendado
Low-Cost USB Barcode Scanners and POS Terminals
Point-of-sale terminals and barcode scanners benefit from the MCF51JM64VLK's USB device capability, which simplifies the USB HID or CDC connection to a host PC. The ColdFire V1 core decodes 1D/2D barcode symbologies within its 50MHz budget, while the integrated peripherals drive buzzers, LEDs, and trigger inputs. With 64KB Flash, firmware can include both the scanner engine and the USB stack. The 80-LQFP package exposes pins for an external imager sensor interface.
Recomendado
USB-Connected Sensor Hubs
Multi-sensor hubs that aggregate temperature, humidity, pressure, and motion data over USB benefit from the MCF51JM64VLK's combination of I2C/SPI connectivity and USB device interface. The 50MHz ColdFire V1 core performs sensor fusion and presents a USB composite device to the host. With 66 GPIO, designers can wire up to 8-12 I2C/SPI sensors plus discrete analog inputs. The compact 80-LQFP package is well-suited to compact hub enclosures.
Recomendado
USB-to-UART / SPI / I2C Bridge Dongles
The MCF51JM64VLK is well-suited to USB-to-serial bridge dongles used in development, factory programming, and field service tools. Its integrated USB OTG controller enumerates as a CDC class device, while the SCI, SPI, and I2C peripherals provide the target-side bridge channels. With 64KB Flash, firmware can include multiple protocol stacks plus bootloader logic. The 3.3V/5V tolerant I/O simplifies connection to legacy UART/SPI peripherals without level shifters.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCF51JM64VLK — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MCF51JM128VLK | MCF51JM32VLK | MCF51JM32EVLK | MCF51JM64EVQH | MCF51JE128VLK |
|---|---|---|---|---|---|---|
| Package | 80-LQFP (14x14) | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same | 80-LQFP (14x14) - same |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Flash Memory | 64 KB | 128 KB (+100%) | 32 KB (-50%) | 32 KB (-50%) | 64 KB (same) | 128 KB (+100%) |
| Core | ColdFire V1 50 MHz | ColdFire V1 50 MHz | ColdFire V1 50 MHz | ColdFire V1 50 MHz | ColdFire V1 50 MHz | ColdFire V1 50 MHz |
| USB OTG | Yes (integrated) | Yes (integrated) | Yes (integrated) | Yes (integrated) | Yes (integrated) | Yes (integrated) |
| CANbus | Yes | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Integrated USB OTG with on-chip transceiver (vs MCF51JM32VLK)
- Flexis series 8-bit/32-bit pin compatibility (vs MC9S08AW60CPUE)
- ColdFire V1 core with USB and CAN in one device (vs MCF51JE128VLK)
Notas de projeto
Route the USB_DP and USB_DM pins (pins 35-36) as a 90-ohm differential pair with matched length (delta less than 150 mil). Keep the pair away from switching signals and place a common-mode choke near the connector for EMI compliance. The VUSB33 pin requires a 0.1uF decoupling capacitor placed within 2mm of the pin to stabilize the internal USB regulator.
Do not assume the JM64 is drop-in to Kinetis KE series without peripheral driver rewrites. The ColdFire V1 interrupt model and register layout differ from ARM Cortex-M0/M4. For new designs, evaluate the pin-compatible MCF51JM128VLK or migrate to MKL02Z/MKL26Z ARM parts only after revalidating firmware. Verify last-time-buy date before committing to long-lead designs.
The MCF51JM64VLK integrates a 3.3V LDO from the external 5V supply; place 4.7uF bulk + 0.1uF ceramic decoupling on each VDD/VSS pair (typically 6 pairs in the 80-LQFP). The USB VUSB33 rail requires 1uF minimum. Brown-out reset is supported via the LVD peripheral; configure LVD threshold in initialization code for predictable reset behavior.
Place the external crystal or oscillator within 1cm of the EXTAL/XTAL pins (pin 80 and adjacent) to minimize parasitic capacitance and EMI. Use a guard ring tied to ground around the crystal area, and keep high-frequency traces away from this zone. For USB designs, dedicate a continuous ground plane beneath the USB differential pair to maintain 90-ohm impedance.
Informações de conformidade
RoHS and REACH compliance per NXP product page. Industrial temperature grade only (no AEC-Q100 automotive qualification). Not recommended for new automotive designs.
