MCP4342-503E/ST - 50kΩ Quad 7-Bit SPI Digital Potentiometer | Microchip
N.º da peça: MCP4342-503E/ST ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.95 | $2,95 |
| 10 | $2.65 | $26,50 |
| 100 | $2.2 | $220,00 |
| 500 | $1.85 | $925,00 |
| 1.000 | $1.6 | $1.600,00 |
MCP4342-503E/ST Visão geral
A digital potentiometer (often abbreviated "digiPOT") is a digitally controlled variable resistor that emulates the behavior of a mechanical potentiometer or trim pot. In the broader component taxonomy, a digital potentiometer belongs to the data-conversion / signal-conditioning family and serves as a programmable resistor network used for gain control, offset trimming, LCD contrast adjustment, and sensor calibration. Unlike mechanical pots, it is set through a serial command and retains its wiper position across power cycles when non-volatile memory is present, as in the MCP4342 family.
Key features include a wide operating supply range of 1.8 V to 5.5 V, low typical quiescent current of around 1 µA at 5 V, ±20 % end-to-end resistance tolerance, SPI serial interface (modes 0,0 and 1,1) up to 10 MHz, and wiper settings stored in non-volatile EEPROM so the part powers up in its last programmed state. Each channel supports both potentiometer and rheostat modes, and a software-controlled wiper lock register is available to prevent unintended changes.
The MCP4342-503E/ST uses a chain of 128 polysilicon resistive elements with CMOS analog switches steered by a 7-bit decoder. The wiper switches between taps with break-before-make action, the EEPROM cell uses the same charge-pump architecture as Microchip's PIC microcontrollers, and the SPI peripheral supports both byte and sequential commands including read, write, increment, and decrement of the wiper position without rewriting the EEPROM.
Typical applications include audio equipment volume and tone control, LCD display contrast and brightness trimming, sensor calibration in industrial and instrumentation systems, programmable gain amplifiers, and any general-purpose mechanical-trim-pot replacement where software-driven or remote adjustment is desired.
When laying out this part, place the 0.1 µF VDD bypass capacitor as close as possible to pin 14, keep analog signal traces short, and avoid running digital lines directly beneath the resistor network. For rheostat-mode operation, connect the unused terminal to the wiper to minimize parasitic capacitance effects.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers shorten the selection cycle and reduce BOM risk.
Alternativas drop-in para MCP4342-503E/ST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MCP4342-503E/ST (mesmo formato e footprint) — diferindo em Package, Resistance Tolerance, Interface, MSL Level, Number of Channels.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MCP4342T-503E/ST
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP4342-104E/ST
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP4342-103E/ST
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP4342-502E/ST
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP4342-503E/ST Classificações máximas e características elétricas
| Product Type | Digital Potentiometer (Quad, Non-volatile) |
| Number of Channels | 4 |
| Number of Taps | 129 (7-bit) |
| End-to-End Resistance | 50 kΩ |
| Resistance Tolerance | ±20 % (typical) |
| Interface | SPI (Modes 0,0 and 1,1), up to 10 MHz |
| Supply Voltage (VDD) | 1.8 V to 5.5 V |
| Supply Current (IDD) | 1 µA typical at 5 V |
| Temperatura de operação | -40 °C to +125 °C (extended) |
| Memory | Non-volatile EEPROM (wiper position retained) |
| Configuration | Potentiometer or Rheostat per channel |
| Encapsulamento | 14-pin TSSOP (ST) |
| Tipo de montagem | Surface Mount |
| Nível MSL | 1 |
| Status RoHS | Compliant |
Configuração de pinos do MCP4342-503E/ST
| Pino 1 | P1A — Channel 1 terminal A (resistor network end) |
| Pino 2 | P1W — Channel 1 wiper terminal |
| Pino 3 | P1B — Channel 1 terminal B (resistor network end) |
| Pino 4 | VSS — Ground reference for analog signals |
| Pino 5 | P2A — Channel 2 terminal A |
| Pino 6 | P2W — Channel 2 wiper terminal |
| Pino 7 | P2B — Channel 2 terminal B |
| Pino 8 | CS — SPI chip select (active low) |
| Pino 9 | SCK — SPI serial clock input |
| Pino 10 | SI — SPI serial data input |
| Pino 11 | SO — SPI serial data output |
| Pino 12 | P3A/P4A — Channel 3/4 terminal A (shared pin in quad mode) |
| Pino 13 | P3W/P4W — Channel 3/4 wiper terminal (shared pin in quad mode) |
| Pino 14 | VDD — Positive supply voltage (1.8 V to 5.5 V) |
Aplicações típicas
MCP4342-503E/ST é adequado para 6 aplicaçãos: Audio Volume and Tone Control, LCD Display Contrast and Brightness Trimming, Sensor Calibration in Industrial Instrumentation, Programmable Gain Amplifier (PGA), Mechanical Trim-Pot Replacement, Power-Supply Voltage Margining and Adjustment.
Audio Volume and Tone Control
The MCP4342-503E/ST is well suited for software-controlled audio volume, balance, and tone control stages in consumer and prosumer audio products. Its 50 kΩ end-to-end resistance and 129 taps give a fine 0.78 dB nominal step over a 78 dB control range when used in the feedback network of an op-amp gain stage, and the non-volatile EEPROM allows the user setting to survive power-down without reloading defaults from a host MCU. Each of the four channels can drive an independent audio gain cell - one for left volume, one for right volume, one for bass, one for treble - eliminating up to four mechanical potentiometers. The 1.8 V to 5.5 V supply range supports direct connection to common 3.3 V and 5 V analog rails; the SPI interface allows MCU-driven or pushbutton up/down control via increment and decrement commands.
Recomendado
LCD Display Contrast and Brightness Trimming
The MCP4342-503E/ST replaces mechanical contrast trimmers on character-LCD and TFT bias-rail adjustment circuits. Its 50 kΩ resistance is well matched to the typical 10 kΩ to 100 kΩ contrast-divider range used on COG and TFT display modules, and the 7-bit resolution gives approximately 0.4 % contrast step granularity - finer than the user's eye can resolve, which prevents visible stepping during adjustment. Because the part retains the last wiper position in EEPROM, contrast settings stay calibrated across power cycles, eliminating the production-line contrast-pot tweak step. Channels 3 and 4 can be re-used to trim backlight current using a series resistor or to set the VCOM voltage on a TFT.
Recomendado
Sensor Calibration in Industrial Instrumentation
Industrial pressure, strain-gauge, and temperature sensor front ends frequently need per-unit gain and offset trimming to remove part-to-part tolerance. The MCP4342-503E/ST provides four independent trim channels that can each be placed in a Wheatstone-bridge excitation network or op-amp offset-correction path. With ±20 % resistance tolerance and 129 taps, the calibration step resolution is approximately 0.16 % per LSB at 50 kΩ - adequate to remove typical sensor-offset errors of 1 % to 5 %. The non-volatile memory allows factory calibration data to be written once and then locked, satisfying many ISO 9001 calibration-traceability requirements, while the -40 °C to +125 °C operating range covers outdoor and process-control environments.
Recomendado
Programmable Gain Amplifier (PGA)
Placing the MCP4342-503E/ST in the feedback network of a transimpedance or non-inverting op-amp stage creates a software-programmable gain amplifier with four independently selectable gain settings. The 50 kΩ end-to-end resistance pairs well with typical feedback capacitor values of 10 pF to 100 pF, keeping the -3 dB bandwidth above 1 MHz in most op-amp topologies. Channels 1 and 2 can be cascaded for coarse/fine gain or used as a single-ended-to-differential converter network, while channels 3 and 4 trim the input common-mode and DC offset. The MCP4342's SPI interface makes the part well suited for automatic gain-control (AGC) loops where the host MCU samples the output amplitude and writes a new wiper code each cycle.
Recomendado
Mechanical Trim-Pot Replacement
The MCP4342-503E/ST is the modern direct replacement for four-section mechanical 50 kΩ trim pots found on legacy industrial and test-and-measurement boards. Replacing a mechanical pot eliminates the need for access holes in the enclosure, removes susceptibility to vibration and contamination, and allows remote adjustment over SPI from a front-panel MCU or USB bridge. With a typical wiper resistance of 75 Ω and bandwidth above 1 MHz on each channel, the digital part introduces negligible error versus the mechanical equivalent in most DC and audio applications. The non-volatile EEPROM and software-writable wiper lock register also enable tamper-proof calibration.
Recomendado
Power-Supply Voltage Margining and Adjustment
The MCP4342-503E/ST can be inserted into the feedback divider of a switching or linear regulator to allow software-controlled output-voltage margining for production test or dynamic voltage scaling. Each of the four channels can independently set a different tap on the resistor divider, allowing the host to step the regulator output through 129 voltage levels for margining tests or to implement a closed-loop dynamic voltage scaling (DVS) profile that tracks the processor's load current. The 1.8 V to 5.5 V analog range is compatible with most point-of-load regulator feedback nodes, and the high-impedance CMOS wiper draws negligible current from the divider, minimizing accuracy loss.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCP4342-503E/ST — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MCP4342T-503E/ST | MCP4342-104E/ST | MCP4342-103E/ST | MCP4342-502E/ST |
|---|---|---|---|---|---|
| Package | 14-TSSOP (ST) | 14-TSSOP (ST) - same | 14-TSSOP (ST) - same | 14-TSSOP (ST) - same | 14-TSSOP (ST) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| End-to-End Resistance | 50 kΩ | 50 kΩ (identical) | 100 kΩ (+100 %) | 10 kΩ (-80 %) | 5 kΩ (-90 %) |
| Number of Channels | 4 | 4 | 4 | 4 | 4 |
| Number of Taps | 129 (7-bit) | 129 (7-bit) | 129 (7-bit) | 129 (7-bit) | 129 (7-bit) |
| Interface | SPI | SPI | SPI | SPI | SPI |
| Supply Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Non-volatile Memory | Yes (EEPROM) | Yes (EEPROM) | Yes (EEPROM) | Yes (EEPROM) | Yes (EEPROM) |
| Packaging Format | Tube | Tape & Reel | Tube | Tube | Tube |
Principais diferenciais
- Non-volatile wiper memory retains settings across power cycles (vs MCP4132 (volatile, single-channel))
- Quad-channel integration replaces four trim pots (vs Mechanical 50 kΩ trim pots)
- Wide 1.8 V to 5.5 V supply range supports both 3.3 V and 5 V rails (vs AD5280 (single-channel, ±15 V capable))
Notas de projeto
Place a 0.1 µF low-ESR ceramic bypass capacitor as close as possible to the VDD pin (pin 14) and a 10 µF bulk capacitor on the same rail within 10 mm. The MCP4342 contains an internal charge pump for EEPROM writes that can inject 1 mA to 5 mA pulses on VDD for periods of up to 5 ms; insufficient bulk capacitance causes VDD to droop and may corrupt EEPROM writes. Add a ferrite bead in series with VDD if the part shares a rail with a noisy switching regulator.
Route the analog wiper traces (P1W/P2W/P3W/P4W) away from digital SPI lines and from high-frequency switching nodes; cross only at 90° if needed. Keep terminal A, terminal B, and wiper traces on the same layer and as short as practical to minimize parasitic capacitance (typically 5 pF to 15 pF) that would otherwise cap the usable bandwidth above 1 MHz. Connect the exposed thermal pad (if present) to a quiet ground pour - on the 14-TSSOP package the pad is on the underside and improves thermal dissipation during EEPROM writes.
The wiper switch resistance is typically 75 Ω and varies with tap position; for high-impedance (>1 MΩ) sensor inputs, connect the unused terminal (A or B) to the wiper to convert the potentiometer to a true rheostat configuration and minimize the impact of the RWA/RWB parasitic resistance. When operating above 100 kHz, include a small series resistor (10 Ω to 100 Ω) at the wiper to dampen the resonant LC formed with the parasitic capacitance and prevent ringing on fast transients.
Do not apply analog voltages outside GND to VDD on the resistor terminals - the internal ESD diodes will forward-bias and inject current into the substrate, corrupting EEPROM and potentially latching the part. Always issue a software wiper-lock before field deployment to prevent accidental EEPROM wear; the MCP4342 EEPROM is rated for approximately 1 million write cycles per channel. Avoid issuing back-to-back increment/decrement commands faster than 2 µs apart, as the internal wiper-switch charge pump needs settling time.
Informações de conformidade
RoHS compliant per Microchip product page. Halogen-free per Microchip environmental certification. Not AEC-Q100 qualified - the automotive-grade equivalent is the MCP4342T-503E/STVAO (separate ordering code).
