MCP6033-E/MS - 1.8V R-R Precision Op Amp | Microchip
N.º da peça: MCP6033-E/MS ✓ AtivoMCP6033-E/MS Visão geral
An operational amplifier is an analog integrated circuit that uses high-gain differential feedback to amplify small voltage differences. The MCP6033 belongs to the precision amplifier hierarchy, combining the functions of an op amp, voltage buffer, instrumentation amplifier stage, and active signal-conditioning element. Its rail-to-rail input and output capability broadens the usable signal and output ranges in low-voltage systems compared with conventional fixed-range amplifiers.
The MCP6033-E/MS supports operation down to 1.8 V, making it suitable for energy-limited systems powered by a single low-voltage cell or a low-voltage regulated rail. Its 14 kHz gain-bandwidth product is appropriate for low-frequency control, monitoring, and sensor-interface circuits rather than high-speed signal processing. The low 150 µV offset helps preserve measurement accuracy when the amplifier is used in gain stages, while the rail-to-rail outputs provide useful output swing near the supply rails.
A distinguishing feature of the MCP6033 is its power-saving Chip Select, or CS, input. In the MCP6031, MCP6032, MCP6033, and MCP6034 family, this feature allows an unselected amplifier to enter a lower-power state. That behavior is valuable in multichannel systems where several amplifiers share limited battery capacity. Designers should still consult the manufacturer datasheet for the exact CS thresholds, output behavior during shutdown, timing, and supply-current limits before using the control pin in a safety-critical state machine.
Typical uses include battery-current monitoring, portable sensor conditioning, low-frequency feedback control, low-voltage buffering, and instrumentation interfaces. Because the MCP6033-E/MS is packaged in 8-MSOP, it supports compact layouts while still exposing power, ground, input, output, and control functions. Its small package makes thermal design and exposed-pad handling less relevant than in large power packages, but stable reference and feedback layouts remain important for offset and noise performance.
The primary design consideration is to operate the inputs and outputs within the device's common-mode and output-swing limits at the selected supply voltage. Place input biasing, feedback, and decoupling components close to the associated pins, and use a quiet ground reference. When CS is not needed, its logic level should be fixed according to the manufacturer datasheet rather than allowed to float.
This page combines manufacturer-family information with practical selection guidance, verified pin-compatible alternatives, comparison criteria, and design notes. It also clarifies package, pricing, sourcing, and replacement considerations so engineers can assess whether the MCP6033-E/MS fits a low-voltage precision-amplifier design before beginning layout work.
Alternativas drop-in para MCP6033-E/MS — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasMCP6033-E/MS Classificações máximas e características elétricas
| Amplifier Type | Single-circuit precision operational amplifier |
| Number of Circuits | 1 circuit |
| Minimum Supply Voltage | 1.8 V |
| Gain-Bandwidth Product | 14 kHz |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Input Offset Voltage | 150 µV |
| Chip Select Function | Power-saving Chip Select input |
| Operating Temperature Grade | E temperature grade |
| Package Type | 8-MSOP |
| Package Width | 3.00 mm |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do MCP6033-E/MS 3.00 mm
Configuração de pinos para MCP6033-E/MS (pacote 3.00 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para MCP6033-E/MS.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MCP6033-E/MS é adequado para 6 aplicaçãos: Battery Current Monitoring, Portable Sensor Conditioning, Low-Voltage Instrumentation, Low-Voltage Feedback Control, Low-Noise Voltage Buffering, Battery-Powered Sensor Interfaces.
Battery Current Monitoring
The MCP6033-E/MS fits low-voltage shunt-current monitoring where the signal may move close to the supply rails. Its rail-to-rail input stage provides useful signal range at low supply voltages, while operation down to 1.8 V supports compact battery-powered instruments. The 14 kHz gain-bandwidth product is suitable for slow current-control feedback and filtered measurements, and the 150 µV input-offset rating helps preserve accuracy near the measurement floor. The power-saving Chip Select input can disable the amplifier during inactive measurement intervals. Designers should scale the shunt signal into the input range, apply an anti-alias filter, and verify settling and common-mode limits from the manufacturer datasheet.
Recomendado
Portable Sensor Conditioning
The MCP6033-E/MS is appropriate for conditioning low-frequency sensor outputs in portable equipment operating from a 1.8 V or higher rail. Rail-to-rail inputs improve utilization of the available signal range, while the 14 kHz gain-bandwidth product supports moderate-frequency amplification without introducing the speed and power cost of a high-bandwidth amplifier. Its low 150 µV input offset is useful when a gain stage must preserve small sensor changes. Use the amplifier in a non-inverting or differential topology, keep feedback resistors close to the device, and place input filtering ahead of the amplifier when the sensor includes meaningful noise.
Recomendado
Low-Voltage Instrumentation
The MCP6033-E/MS can serve as the input stage or buffer in compact low-voltage instrumentation. Its 1.8 V minimum supply supports portable measurement systems, while rail-to-rail inputs and outputs allow more of the available signal span to reach downstream converters or control circuitry. The 150 µV offset specification is particularly relevant when small transducer outputs are amplified, and the 14 kHz bandwidth is well matched to low-frequency measurement channels. For instrumentation layouts, use a quiet analog ground, route sensor inputs away from switching nodes, and verify resistor tolerance because practical accuracy also depends on the gain network and reference source.
Recomendado
Low-Voltage Feedback Control
The MCP6033-E/MS is suitable for slow, low-voltage feedback loops in portable or compact control systems. Its 14 kHz gain-bandwidth product provides useful loop bandwidth for temperature, level, or current regulation, while operation down to 1.8 V matches single-cell and low-voltage regulated systems. Rail-to-rail output operation improves actuator drive range when the output remains within the loaded output-swing limits. Designers should compensate the amplifier for the intended capacitive load, place compensation near the relevant pins, and use the Chip Select function only when shutdown timing is compatible with the controlled system.
Recomendado
Low-Noise Voltage Buffering
The MCP6033-E/MS can buffer a low-frequency voltage source when its output must present a higher impedance to the next circuit. Rail-to-rail input and output stages are helpful when the source voltage occupies much of the 1.8 V supply range, and the 150 µV input-offset specification helps limit errors introduced by the buffer stage. The amplifier's 14 kHz bandwidth is adequate for slow analog signals but not for wideband data lines. Confirm the source impedance, capacitive load, output-current requirement, and settling time in the manufacturer datasheet, then place the buffer close to the receiving circuit to minimize trace pickup.
Recomendado
Battery-Powered Sensor Interfaces
The MCP6033-E/MS supports compact battery-powered sensor interfaces by combining 1.8 V operation with a dedicated power-saving Chip Select input. A system can place the amplifier into its lower-power state during long idle periods and enable it for measurements, reducing the time that the amplifier contributes to the overall power budget. The rail-to-rail input stage accommodates sensor signals near either supply rail, and the 14 kHz bandwidth supports filtered sensor measurements rather than high-speed acquisition. Validate the Chip Select logic and unselected output behavior in the manufacturer datasheet, and ensure external feedback and sensor nodes cannot back-power the amplifier while it is deselected.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCP6033-E/MS — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto |
|---|---|
| Brand | Microchip Technology |
| Package | 8-MSOP |
| Minimum Supply Voltage | 1.8 V |
| Number of Circuits | 1 circuit |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Gain-Bandwidth Product | 14 kHz |
| Input Offset Voltage | 150 µV |
| Power-Saving Control | Chip Select input |
| Temperature Grade | E grade |
Principais diferenciais
- Adds a dedicated power-saving Chip Select input within the MCP6033 family (vs MCP6031)
- Supports low-voltage rail-to-rail signal conditioning (vs MCP6033-E/SN)
- Uses an 8-MSOP package for compact portable layouts (vs MCP6033-E/MC)
Notas de projeto
Use the Chip Select input to reduce power consumption only after confirming its active and inactive logic levels, transition timing, and output behavior in the manufacturer datasheet. Pull the control pin to a defined state when the host can lose power; do not allow it to float. Also check every feedback-connected node during shutdown so the amplifier cannot be reverse-biased through its inputs or output. The 1.8 V minimum supply provides useful low-voltage flexibility, but the complete supply-current and shutdown-current values must be taken from the datasheet.
Place the amplifier, feedback components, and decoupling capacitor close together, with the shortest practical input routes and a direct return path to the analog ground reference. Connect the decoupling capacitor at the device supply pins with minimal loop area. For a differential sensor input, route both signal lines together and maintain symmetry to reduce conversion of common-mode noise into differential error. The 150 µV offset specification does not remove errors caused by asymmetric layout, ground movement, or resistor tolerance.
Do not treat the rail-to-rail designation as proof that the output can swing exactly to either supply rail. Check loaded output-voltage limits, output-current capability, input common-mode limits, and stability with the intended capacitive load. The 14 kHz gain-bandwidth product is suitable for low-frequency sensor and control paths, but attempting wideband signal amplification can create excessive gain-bandwidth error. Confirm noise, offset, bias-current, and shutdown specifications at the actual supply voltage and temperature.
Informações de conformidade
The E temperature-grade designation does not establish automotive qualification. Request lot-specific environmental and material compliance documentation through the Request a Quote form.