Renesas Electronics

MK2308S-2ILFT - 133.3MHz 8-Output Zero-Delay Buffer | Renesas

N.º da peça: MK2308S-2ILFT ✓ Ativo
3 V to 3.6 V Vdss 16-pin SOIC Package 133.3 MHz Speed
MOQ: 1 |

MK2308S-2ILFT Visão geral

Renesas Electronics MK2308S-2ILFT is a PLL-based, low-jitter, low-skew zero-delay clock buffer operating up to 133.3 MHz at 3.3 V, with eight CMOS outputs in a 16-pin SOIC package. The device provides four 1X outputs and four 1/2X outputs, allowing simultaneous propagation and divided clock distribution from one source.

A zero-delay buffer is a clock-integrity device that uses a phase-locked loop to reproduce and distribute a clock while compensating for internal propagation delay. In system terms, it belongs to the clock buffer and driver class within clock and timing integrated circuits, where multiple low-skew copies of a high-speed clock are required for processors, memory interfaces, communication links, and test equipment. The MK2308S-2ILFT combines clock generation, frequency division, and output buffering in one integrated circuit.

Key features include operation from a 3 V to 3.6 V supply, a maximum operating frequency of 133.3 MHz, and output-to-output skew below 250 ps in zero-delay mode. Its eight outputs are organized as four 1X channels and four 1/2X channels. The PLL-based architecture aligns the rising edge of the input clock with the rising edges of the outputs, helping minimize accumulated timing displacement between destinations.

The low phase-noise and low-jitter characteristics are important in systems that transfer synchronous data at high clock rates. By producing several outputs from a common PLL reference, the device reduces the cumulative skew that can develop when one clock source drives multiple loads through separate buffers. The CMOS interface also supports integration with 3.3 V digital logic, while the available test and bypass behavior aids board-level validation.

Typical uses include CPU and DSP clock distribution, network-interface clock fanout, memory-controller clock distribution, communications equipment, and industrial control systems. The four divided outputs are particularly useful when a subsystem requires a reference at half the fundamental clock frequency. The same package also supports compact implementations where multiple clock domains must originate from one low-frequency reference.

Designers should preserve a continuous supply path and route clock outputs according to the package guidance in the manufacturer datasheet. PCB return paths, ground-plane continuity, and matched trace characteristics help control edge degradation and coupling. The datasheet must be consulted for the exact pin assignment, output-disable truth table, bypass configuration, and recommended external component values before layout is released.

This page combines the verified device characteristics, a practical application guide, pin and documentation guidance, and a disciplined comparison framework. It also distinguishes true same-footprint alternatives from functional clock-buffer options that would require different routing or a redesigned land pattern.

Alternativas drop-in para MK2308S-2ILFT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com MK2308S-2ILFT (mesmo formato e footprint) — diferindo em Device Type, Supply Voltage.

Renesas Electronics
Device Type: Zero-delay, low-skew clock buffer
Supply Voltage: 3.3 V
Comparar com MK2308S-2ILFT →

MK2308S-2ILF

✅ Drop-In
Renesas Electronics
📦 16-SOIC
Zero-delay, low-skew clock buffer · 3.3 V · 133.3 MHz

Consulte o preço

Ver ficha técnica →

MK2308S-1HLFTR

✅ Drop-In
📦 16-SOIC
Same Renesas eight-output, 133 MHz-class zero-delay-buffer family and 16-SOIC package, but the -1 versus -2 family designator can change supported operating configurations; no verified key-parameter difference was published.

📋 Alternativa de referência (fora do catálogo)

MK2308S-2ILFT Especificações

Device Type PLL-based zero-delay clock buffer
Bus Interface CMOS
Tensão de alimentação 3 V to 3.6 V
Maximum Frequency 133.3 MHz
Número de saídas 8 outputs
1X Output Count 4 outputs
1/2X Output Count 4 outputs
Output Skew Below 250 ps in zero-delay mode
Listed Skew 200 ps
Phase Noise Low phase noise
Jitter Low jitter
Delay Architecture PLL-based zero input-to-output delay
Package Type 16-pin SOIC
Package Width 3.90 mm
Tipo de montagem Surface Mount

Guia de Configuração de Pinos do MK2308S-2ILFT 3.90 mm

Configuração de pinos para MK2308S-2ILFT (pacote 3.90 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 3.90 mm para MK2308S-2ILFT

Nenhum dado detalhado de pinagem disponível para MK2308S-2ILFT.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

MK2308S-2ILFT é adequado para 6 aplicaçãos: CPU and DSP Clock Fanout, Network and Communication Equipment, Memory Interface Clock Distribution, Industrial Control and Instrumentation, Audio and Video Clock Distribution, Test and Measurement Equipment.

🖥️

CPU and DSP Clock Fanout

The MK2308S-2ILFT fits processor and DSP clock trees that require several coordinated copies of the same source signal. Its PLL-based architecture provides zero input-to-output delay up to 133.3 MHz at 3.3 V, while output-to-output skew remains below 250 ps in zero-delay mode. Four outputs operate at 1X and four at 1/2X, allowing full-rate logic and a divided reference domain to share one device. This can reduce separate fanout-buffer count while preserving a common PLL reference. The principal trade-off is dependence on careful supply decoupling and output routing, because fast edges make board skew and return-path discontinuities increasingly important.

🌐

Network and Communication Equipment

The MK2308S-2ILFT is appropriate for communication equipment that distributes a 3.3 V clock to multiple serial, fabric, or packet-processing blocks. Eight outputs permit substantial fanout from one reference, and the divided-output bank can serve slower management or reference domains. Its low-jitter PLL architecture helps maintain consistent edge timing across channels, while the 200 ps listed skew value and sub-250 ps zero-delay-mode limit provide useful timing margins. In a communications design, the device should be placed close to the loads it serves to limit trace-induced skew, while clock and data routes should be kept away from high-current switching nodes.

🖥️

Memory Interface Clock Distribution

The MK2308S-2ILFT can distribute a high-speed clock to memory controllers and interface logic that require closely related clock arrivals. At 3.3 V, its operating frequency reaches 133.3 MHz, and the four 1X outputs can feed multiple loads with a stated zero-delay-mode output skew below 250 ps. The 1/2X outputs provide a separate divided clock where the interface architecture needs it. Actual timing closure still depends on input and output capacitance, board delay, and the receiving devices' input thresholds. Place the buffer near the clock-consuming cluster and use continuous reference planes to minimize skew accumulation between the IC and its destinations.

🏭

Industrial Control and Instrumentation

The MK2308S-2ILFT is useful in industrial control and test systems that synchronize sampling, conversion, or communications blocks from a shared clock. Its eight outputs support several destinations, while the 1/2X bank can generate a related lower-rate clock for slower peripheral logic. Low phase noise and low jitter are valuable when measurement timing or control-loop coordination depends on repeatable edges. For reliable industrial implementation, confirm the ordering variant's temperature limits and follow the manufacturer's layout guidance. The clock nets should be routed over a continuous ground reference, with switching regulators and high-current outputs positioned away from sensitive clock traces.

🎧

Audio and Video Clock Distribution

The MK2308S-2ILFT can provide synchronized 3.3 V clock outputs for audio, video, or multimedia subsystems requiring multiple related clock domains. Its low-jitter PLL technique and low-skew output arrangement help maintain consistent sampling relationships across converters, serializers, and digital signal processors. Four 1X outputs support full-rate destinations, while four 1/2X outputs can support related divider domains. The device does not remove the need for careful analog and digital partitioning. Keep the clock buffer away from switching-node currents, preserve a low-impedance ground return, and verify edge-rate-dependent loading with the output configuration recommended in the manufacturer datasheet.

🔧

Test and Measurement Equipment

The MK2308S-2ILFT is appropriate for test and measurement equipment that must fan out a reference clock to multiple acquisition, trigger, or conversion paths. Eight outputs provide flexible routing, and the half-rate bank can support instrumentation blocks that do not require the full 133.3 MHz fundamental. The PLL-based zero-delay operation simplifies timing relationships between instruments, while the specified output skew below 250 ps supports predictable relative phase. In high-performance test systems, use short clock routes, minimize stub loading, and verify the final eye and timing margin at each receiver. The manufacturer datasheet's test and direct-input modes can assist board validation.

What is the Renesas MK2308S-2ILFT?
The Renesas MK2308S-2ILFT is an eight-output, PLL-based zero-delay clock buffer designed to distribute clocks up to 133.3 MHz at 3.3 V. According to the manufacturer datasheet, it provides four 1X outputs and four 1/2X outputs from one input, allowing a single device to serve both full-rate and half-rate clock destinations. The device is packaged in a 16-pin SOIC.
What is the operating voltage of MK2308S-2ILFT?
The MK2308S-2ILFT operates from a 3 V to 3.6 V supply, with 3.3 V as the nominal operating condition described for its high-speed clock outputs. The manufacturer datasheet identifies the device as a low-jitter, low-skew PLL-based zero-delay buffer. Its 16-pin SOIC package and CMOS interface are intended for compatibility with 3.3 V digital systems.
How many clock outputs does MK2308S-2ILFT have?
The MK2308S-2ILFT has eight clock outputs divided into two functional banks. Four outputs reproduce the input clock at 1X, while four outputs operate at 1/2X, as described in the manufacturer datasheet. This arrangement lets one source feed full-rate and divided-clock domains without requiring separate divider and buffer stages.
What is the maximum clock frequency of MK2308S-2ILFT?
The MK2308S-2ILFT supports clock operation up to 133.3 MHz at 3.3 V. The manufacturer datasheet describes zero input-to-output delay at this speed, with the rising edge of the input aligned to the rising edges of the outputs. Actual board operation still depends on supply integrity, output loading, trace topology, and the required timing margin.
What is the output skew of MK2308S-2ILFT?
The manufacturer datasheet specifies output-to-output skew below 250 ps in zero-delay mode, while a component listing identifies a nominal skew value of 200 ps. The distinction matters when evaluating a complete design: the 250 ps figure is the stated upper boundary in zero-delay operation, whereas 200 ps is the listed skew specification. Both values describe the relationship among the eight outputs.
Where can I download the MK2308S-2ILFT datasheet PDF?
The official manufacturer datasheet is available through the Renesas document page at https://www.renesas.com/en/document/dst/mk2308-2-datasheet. It covers the MK2308-2 family, including the MK2308S-2ILFT ordering variant. Use the manufacturer PDF for the authoritative pin-description table, output-control logic, timing characteristics, recommended operating circuit, and package drawing.
Where can I find the MK2308S-2ILFT pinout?
The MK2308S-2ILFT pin assignment is shown in the pin-description and package-drawing sections of the Renesas MK2308-2 datasheet. The component uses a 16-pin SOIC, so the package drawing identifies all 16 terminal positions, including power, ground, input, control, and the eight clock outputs. Assign PCB nets directly from that table rather than inferring connections from similar clock-buffer devices.
What can replace the MK2308S-2ILFT?
The closest documented same-family replacement is the Renesas MK2308S-2ILF, which retains the same 16-pin SOIC architecture but uses a different ordering suffix and temperature-grade code. A second same-family option is the MK2308S-1HLFTR, although its suffix denotes a different device configuration and must be checked against the required output frequencies. No verified cross-brand part was shown to be a pin-for-pin replacement.
Is the MK2308S-1HLFTR a drop-in replacement for MK2308S-2ILFT?
The MK2308S-1HLFTR is a Renesas MK2308-family clock buffer in the same general SOIC family, but it should not be treated as an unconditional substitute. The manufacturer lists both the MK2308 and MK2308-2 families at up to 133 MHz at 3.3 V, while their suffix and family designators can distinguish device configurations. Verify pin functions, output ratios, control inputs, and timing limits against the relevant datasheet before substitution.
When should I choose the MK2308S-2ILFT over another clock buffer?
Choose the MK2308S-2ILFT when one input must feed up to eight coordinated destinations and both 1X and 1/2X clocks are required. Its PLL-based zero-delay architecture, eight outputs, 133.3 MHz maximum operating frequency, and sub-250 ps output-skew specification make it appropriate for compact multi-load clock distribution. Select another part when a fixed-ratio clock generator, source-synchronous clock, or different output architecture is needed instead.
Is MK2308S-2ILFT suitable for CPU and DSP clock distribution?
The MK2308S-2ILFT is suitable for CPU, DSP, network-processor, and memory-interface clock distribution when the system needs several low-skew copies of one clock. Its eight outputs can reduce the number of separate fanout stages, and the four 1/2X outputs can feed lower-rate domains. Timing margins must still be checked across PCB traces, connectors, and receiving devices.
What is the difference between a zero-delay buffer and a regular clock buffer?
A zero-delay buffer uses internal PLL techniques to align output edges with the input edge while distributing the clock, whereas a conventional buffer generally passes the clock with a defined propagation delay. The MK2308S-2ILFT also includes four 1X and four 1/2X outputs, giving it more clock-generation flexibility than a basic fanout-only buffer. The circuit must still include the configuration and bypass components specified by the manufacturer.
Does the MK2308S-2ILFT need any external clock source?
The MK2308S-2ILFT requires an input reference to establish the output clock; it is not an autonomous crystal oscillator. The manufacturer describes it as a PLL-based zero-delay buffer with outputs generated from the PLL or directly from the input for testing. The exact input frequency range, reference configuration, and operating-mode requirements should be taken from the MK2308-2 datasheet before system timing is approved.
Where can I buy MK2308S-2ILFT and check its lead time?
Use the Request a Quote form on this page to ask for MK2308S-2ILFT availability, current lead time, and order quantities. The manufacturer and distributor listings confirm the exact 16-pin SOIC ordering code, but they do not provide a reusable quote for every quantity break. A direct quote request is therefore the appropriate way to confirm current sourcing terms for the required suffix and package configuration.
What is the price and stock status of MK2308S-2ILFT?
Current price and stock should be obtained through the Request a Quote form on this page because market pricing and inventory can change with quantity, date, and supply conditions. The verified distributor records identify the exact MK2308S-2ILFT part and its 133.3 MHz 16-pin SOIC configuration, but they do not expose a complete quantity-break table suitable for fixed published pricing. The quote form can confirm the current commercial terms.
What are the key specifications of MK2308S-2ILFT that engineers should know?
The key specifications are a 3 V to 3.6 V supply, operation up to 133.3 MHz, eight CMOS outputs, four 1X outputs, four 1/2X outputs, and output-to-output skew below 250 ps in zero-delay mode. The Renesas datasheet also identifies low phase noise and low jitter as core performance characteristics. These parameters define its suitability for compact, low-skew clock-fanout designs.

Dados de referência de engenharia para MK2308S-2ILFT — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the MK2308S-2ILFT when a 3.3 V system needs one reference distributed to as many as eight destinations and requires both full-rate and half-rate clocks. Its PLL-based zero-delay operation, four 1X outputs, four 1/2X outputs, 133.3 MHz maximum frequency, and low-skew specification make it especially useful for compact processor, communications, industrial, and test clock trees. Consider MK2308S-2ILF when its temperature-grade suffix better matches the production environment after confirming the exact electrical specifications. Evaluate MK2308S-1HLFTR only after comparing its output configuration, control inputs, timing limits, and temperature rating against the -2ILFT requirements. For designs needing more than eight outputs, different voltage levels, source-synchronous edge-rate requirements, or independent clocks, use a clock-tree IC designed around those functions rather than treating a functional equivalent as a drop-in replacement.

Comparação com alternativas

Parâmetro Este produto MK2308S-2ILF MK2308S-1HLFTR
Package 16-SOIC 16-SOIC 16-SOIC
Brand Renesas Electronics Renesas Electronics Renesas Electronics
Device Type PLL-based zero-delay clock buffer PLL-based zero-delay clock buffer PLL-based zero-delay clock buffer
Maximum Frequency 133.3 MHz 133.3 MHz 133 MHz
Number of Outputs 8 outputs 8 outputs 8 outputs
Architecture Low-jitter PLL-based Low-jitter PLL-based Low-jitter PLL-based

Principais diferenciais

  • Eight-output clock distribution with dual output ratios (vs MK2308S-1HLFTR)
  • Pin-compatible ordering option for temperature-sensitive procurement (vs MK2308S-2ILF)
  • Documented low-skew zero-delay operation (vs MK2308S-1HLFTR)

Notas de projeto

Route each clock output over a continuous reference plane with a short, direct path from the SOIC. Avoid test pads, long stubs, and abrupt changes in reference geometry on clock nets because they can degrade edge quality and add uncorrected delay. Use the manufacturer pin-description table and package drawing when assigning output nets, and confirm all unused outputs are disabled in the configuration selected for the design.

Place the 3.3 V decoupling capacitor close to the supply and ground terminals, with the shortest possible ground return and no plane splits beneath the clock routes. The PLL-based architecture requires clean supply delivery for predictable jitter and phase alignment, particularly when eight outputs are active. Use only the capacitance and ESR recommendations stated in the manufacturer datasheet and verify startup behavior across the intended supply range.

Treat the 1X and 1/2X outputs as separate timing groups and include their edge relationship in system timing analysis. Account for trace delay, receiver threshold variation, load capacitance, and any output-disable or bypass configuration in the worst-case budget. Because published skew is below 250 ps in zero-delay mode, board-level delay differences can become significant relative to the available margin.

Do not assume that similar MK2308 ordering suffixes are automatically interchangeable. The target uses the -2ILFT suffix, while MK2308S-2ILF changes the temperature-grade code and MK2308S-1HLFTR belongs to a differently designated family configuration. Before substitution, compare supply range, output ratios, control logic, temperature rating, pin names, and timing characteristics using the manufacturer datasheets for both exact orderable parts.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

No specific RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified in the product pages or technical records for this orderable variant.

Dados verificados em: 2026-11-10 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

MK2308S-2ILFT datasheet MK2308S-2ILFT pinout MK2308S-2ILFT datasheet pdf MK2308S-2ILFT equivalent MK2308S-2ILFT replacement MK2308S-2ILFT cross reference MK2308S-2ILFT 16-SOIC footprint MK2308S-2ILFT zero delay buffer MK2308S-2ILFT 133.3MHz MK2308S-2ILFT clock distribution MK2308S-2ILFT price MK2308S-2ILFT stock Renesas MK2308S-2ILFT MK2308S-2ILFT vs MK2308S-1HLFTR MK2308S-2ILFT application circuit

Componentes & termos relacionados

Renesas Electronics MK2308S-2ILFT MK2308S-2ILF MK2308S-1HLFTR MK2308-2 zero-delay buffer clock buffer clock driver clock and timing integrated circuit phase-locked loop PLL low jitter low phase noise output-to-output skew zero input-to-output delay CMOS 1X output 1/2X output 133.3 MHz 3.3 V 16-pin SOIC SOIC family surface-mount package industrial electronics communications equipment
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ