MKL24Z32VLK4 - 48MHz Cortex-M0+ USB MCU | NXP
N.º da peça: MKL24Z32VLK4 ✓ AtivoMKL24Z32VLK4 Visão geral
An ARM Cortex-M0+ microcontroller is a low-complexity, 32-bit embedded processor designed for cost-sensitive control systems. Within the product hierarchy, it belongs to the ARM Cortex-M family, then embedded processors, then microcontrollers and semiconductors. The Kinetis KL2 family adds USB connectivity to the ultra-low-power Kinetis KL1 architecture. This combination supports compact designs that need efficient control processing without a higher-performance Cortex-M4 core.
The MKL24Z32VLK4 operates at 48 MHz and includes 32 KB of flash plus 4 KB of SRAM. Its USB 2.0 controller can operate as a full-speed USB device or as a USB On-The-Go host and device, depending on the selected family member and configuration. A 12-bit ADC, flexible GPIO, serial interfaces, timers, and low-power operating modes broaden its usefulness for embedded measurement, communication, and control tasks.
The Kinetis architecture provides an efficient balance between processing performance, memory, and power consumption for battery-powered and space-constrained systems. Its Cortex-M0+ instruction set supports compact control code, while the dedicated USB controller handles protocol traffic without requiring a separate USB interface device. The 80-LQFP package also exposes a broad set of peripherals and debug functions for prototype development and production integration.
Typical uses include USB-connected sensors, portable test equipment, industrial data loggers, low-power control panels, and USB-to-digital-interface adapters. In these systems, the MCU can acquire analog measurements, manage operator inputs, execute control logic, and communicate with a host computer over full-speed USB. The combination of 48 MHz processing and integrated USB simplifies the bill of materials compared with a discrete processor and USB bridge.
PCB design should preserve short, controlled USB data paths and provide appropriate decoupling close to the power and ground pins. Follow the manufacturer pin-connection and layout guidance when assigning the 80-pin LQFP footprint, programming signals, clock sources, and analog inputs. Firmware must also account for USB enumeration, bus-power behavior, and the transition between active and low-power operating modes.
This page consolidates the core device characteristics, same-package Kinetis alternatives, comparison parameters, and practical design guidance for engineers evaluating the MKL24Z32VLK4 in USB-enabled embedded systems. It also distinguishes the target from functional alternatives that require different packages, firmware changes, or PCB redesign.
Alternativas drop-in para MKL24Z32VLK4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MKL24Z32VLK4 (mesmo formato e footprint) — diferindo em Architecture, Flash Memory, Package, Product Type, SRAM.
MKL24Z16VLK4
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MKL24Z64VLK4
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MKL24Z128VLK4
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MKL24Z256VLK4
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MKL24Z32VLK4 Classificações máximas e características elétricas
| Product Type | ARM Cortex-M0+ Kinetis KL2 Microcontroller |
| CPU Core | ARM Cortex-M0+ |
| Architecture | 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 4 KB |
| USB Version | USB 2.0 full-speed |
| USB Controller | Full-speed USB device or USB On-The-Go controller |
| ADC Resolution | 12 bit |
| Faixa de temperatura de operação | -40 °C to +105 °C |
| Encapsulamento | 80-LQFP, 12 x 12 mm |
| Terminal Count | 80 terminals |
| Terminal Form | Gull wing |
| Package Shape | Square |
| Temperature Grade | Industrial |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do MKL24Z32VLK4 square
Configuração de pinos para MKL24Z32VLK4 (pacote square). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para MKL24Z32VLK4.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MKL24Z32VLK4 é adequado para 6 aplicaçãos: USB Data Logger, Portable Measurement Instrument, Industrial Control Interface, USB Security and Access Peripheral, Connected Environmental Sensor, Battery-Powered USB Dongle.
USB Data Logger
The MKL24Z32VLK4 fits a compact USB data logger because it combines a 48 MHz ARM Cortex-M0+ core, 32 KB of flash, 4 KB of SRAM, and a full-speed USB 2.0 controller in one device. The MCU can collect sensor readings through its 12-bit ADC, apply local filtering, store recent records, and transmit them to a host computer over USB. Integrating the USB controller reduces board area and component count compared with a discrete USB bridge. The main design constraint is the 32 KB code limit, so buffering and firmware should avoid unnecessary duplication. For continuous logging, use DMA-capable peripherals where appropriate and size the USB descriptor and transfer buffers against the available 4 KB SRAM.
Recomendado
Portable Measurement Instrument
A portable measurement instrument benefits from the MKL24Z32VLK4's integration of control processing, 12-bit conversion, and full-speed USB communication. The 48 MHz Cortex-M0+ core can coordinate sampling, calibration, user commands, and display or keypad updates while USB provides a simple connection to a laptop or service computer. The 80-LQFP package exposes a broad peripheral set without requiring a very small board, while the -40 °C to +105 °C rating supports industrial environments when the complete assembly is also qualified. Design the analog front end separately from noisy digital paths, provide filtering at the ADC input, and verify that the 4 KB SRAM is sufficient for acquisition buffers, USB descriptors, and stack overhead.
Recomendado
Industrial Control Interface
The MKL24Z32VLK4 is appropriate for an industrial control interface that must connect a host computer to local actuators or sensors. Its 48 MHz ARM Cortex-M0+ core can execute deterministic control and communication routines, while the integrated full-speed USB controller removes the need for a separate USB transceiver and controller. The 80-LQFP package provides sufficient I/O and analog resources for a multi-channel interface, including the 12-bit ADC and general-purpose serial peripherals. Industrial qualification of the finished product remains necessary even though the MCU supports -40 °C to +105 °C operation. Use isolated boundaries where required, protect external lines from transients, and validate timing margin under worst-case bus and peripheral load conditions.
Recomendado
USB Security and Access Peripheral
The MKL24Z32VLK4 can serve as the controller in a USB security key, reader, or access-control peripheral because it provides dedicated full-speed USB connectivity, general-purpose I/O, and enough deterministic processing for protocol handling. A 48 MHz Cortex-M0+ core supports command parsing, state management, and communication with an attached reader or sensor while the 32 KB flash stores firmware and fixed configuration data. Its 4 KB SRAM is suitable for short protocol transactions, although cryptographic buffers and simultaneous communication tasks must be checked carefully. Protect secret keys in hardware where the selected part provides that capability, implement secure update procedures, and use USB filtering in the system design to reduce exposure to unintended host connections.
Recomendado
Connected Environmental Sensor
A connected environmental sensor can use the MKL24Z32VLK4 to combine local sensing, signal conditioning, and USB reporting in a compact assembly. The 12-bit ADC supports moderate-resolution measurements from temperature, light, or gas-sensor interfaces, while the 48 MHz core handles sampling schedules, filtering, calibration, and USB enumeration. Integrated USB makes the product convenient for calibration and maintenance without adding a separate communications processor. The 32 KB flash limit favors compact application code, and the 4 KB SRAM should be allocated explicitly to sensor conversion results and USB transfer buffers. Place analog inputs away from USB and switching-current paths, provide local filtering, and verify the sensor heater or actuator timing against the application's control latency.
Recomendado
Battery-Powered USB Dongle
The MKL24Z32VLK4 is well suited to a battery-powered USB dongle that needs low-power control and direct host connectivity. The Kinetis KL2 architecture integrates a full-speed USB controller with an efficient 48 MHz ARM Cortex-M0+ processor, eliminating a separate USB bridge and allowing the design to sleep between user interactions. Its 32 KB of flash supports compact firmware for identity, configuration, and control functions, while 4 KB of SRAM accommodates short protocol exchanges. Power-budget analysis must include USB attachment, suspended operation, and the load current of any attached sensor or indicator. Firmware should minimize polling and use interrupt-driven transfers, while the PCB should provide controlled routing for USB data and a stable reference and decoupling network for the MCU.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MKL24Z32VLK4 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MKL24Z16VLK4 | MKL24Z64VLK4 | MKL24Z128VLK4 | MKL24Z256VLK4 |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 80-LQFP, 12 x 12 mm | 80-LQFP, 12 x 12 mm | 80-LQFP, 12 x 12 mm | 80-LQFP, 12 x 12 mm | 80-LQFP, 12 x 12 mm |
| CPU Core | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ | ARM Cortex-M0+ |
| Maximum CPU Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 32 KB | 16 KB | 64 KB | 128 KB | 256 KB |
| ADC Resolution | 12 bit | 12 bit | 12 bit | 12 bit | 12 bit |
| USB Interface | Full-speed USB 2.0 | Full-speed USB 2.0 | Full-speed USB 2.0 | Full-speed USB 2.0 | Full-speed USB 2.0 |
Principais diferenciais
- Balanced embedded memory configuration (vs MKL24Z16VLK4)
- Lower flash capacity than larger KL24 options (vs MKL24Z64VLK4)
- Compact single-chip USB implementation (vs MKL24Z256VLK4)
Notas de projeto
Route the USB D+ and D- traces as a controlled impedance pair with continuous reference planes and minimal stubs. Keep the USB transceiver and supporting components close to the relevant MCU pins, and avoid splitting the ground plane beneath the pair. Follow the manufacturer layout guidance for decoupling, VDD pins, and test points. Because the 80-LQFP footprint exposes many signals, use the official pin table when assigning adjacent pins to sensitive analog functions.
Place the required local bypass capacitors at the associated power pins and provide a low-impedance return for every supply connection. USB bus-powered systems must also account for the current available from the host and the additional load created by sensors, indicators, or regulators. Separate analog and digital supply paths where the board permits it. Validate brownout behavior, startup sequencing, and supply ripple during USB enumeration rather than checking only steady-state current.
Do not assume that every 80-LQFP KL24 pin performs the same function in every family member. Before schematic capture, check the alternate-function table for the exact flash-capacity variant, especially for USB, UART, SPI, I2C, timer, and debugging assignments. Moving from MKL24Z32VLK4 to a larger-memory device can preserve the mechanical footprint while changing muxing or peripheral availability. Validate startup, clock, interrupt, and communication assignments after any substitution.
Informações de conformidade
The manufacturer product page identifies the device as active and provides environmental-quality documentation, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was included in the accessed product information.