MP1740EC-LF-P - 3W Mono Class-D Amplifier | MPS
N.º da peça: MP1740EC-LF-P ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $0 | $0,00 |
| 10 | $0 | $0,00 |
| 100 | $0 | $0,00 |
| 500 | $0 | $0,00 |
| 1.000 | $0 | $0,00 |
MP1740EC-LF-P Visão geral
A Class-D audio amplifier is a switching power amplifier that uses a full-bridge H-bridge output to deliver energy to a speaker. Compared with a linear Class-AB amplifier, its Class-D topology can reduce amplifier power loss and improve operating efficiency. The MP1740 combines that efficiency with the audio fidelity associated with Class-AB operation, while its 2 V/V default gain can be changed by selecting different input resistors.
The principal verified features include 3 W output into a 4-ohm speaker, 91% efficiency, mono Class-D operation, a full-bridge output, and a 1.55 mm by 1.55 mm WLCSP package. The manufacturer page identifies the MP1740 as a low-power mono BTL Class-D audio amplifier and identifies EV1740EC-00A as its evaluation board. These characteristics make the device suitable for portable speakers, compact consumer audio, and embedded audio products.
Because the MP1740 uses a BTL output, the speaker connections are not referenced to ground in the same way as a conventional single-ended amplifier. PCB layout, speaker impedance, input filtering, supply decoupling, and thermal performance must be reviewed against the manufacturer documentation. The 1.55 mm by 1.55 mm WLCSP also requires assembly capability and careful land-pattern design.
Typical designs place the amplifier near the speaker connector, connect the differential Class-D outputs to the speaker, and bypass the supply close to the device. The amplifier's 91% efficiency means less power is dissipated internally than with a comparable linear amplifier at the same stated operating point, but speaker loading and supply conditions still determine actual thermal and acoustic performance. The MP1740 is therefore most appropriate when a compact, efficient, mono speaker drive solution is required.
This page combines the verified manufacturer and distributor descriptions with practical design guidance, comparison fields, procurement context, and application-oriented engineering information. It does not infer unverified electrical limits, pin names, pricing values, lifecycle claims, or compliance declarations.
Alternativas drop-in para MP1740EC-LF-P — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MP1740EC-LF-P (mesmo formato e footprint).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MP1740EC-LF-Z
✅ Drop-In✓ Em estoque
Consulte o preço
Ver ficha técnica →MP1740EC-LF-P Classificações máximas e características elétricas
| Amplifier Type | Class-D audio amplifier |
| Channel Configuration | 1-channel mono |
| Output Power | 3 W into 4 ohm speaker |
| Eficiência | 91% |
| Output Topology | Full-bridge H-bridge BTL |
| Gain | 2 V/V |
| Input Configuration | Differential audio input |
| Encapsulamento | 9-WLCSP, 1.55 mm x 1.55 mm |
| Tipo de montagem | Surface mount |
| Nominal Speaker Load | 4 ohm |
| Application Category | Low-power audio amplification |
| Manufacturer Evaluation Board | EV1740EC-00A |
| Manufacturer Product Classification | Low-power mono BTL Class-D audio amplifier |
| Output Mode | Bridge-tied load |
| Nominal Power Rating | 3 W |
| Package Pin Count | 9 pins |
Guia de Configuração de Pinos do MP1740EC-LF-P 9 pins
Configuração de pinos para MP1740EC-LF-P (pacote 9 pins). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para MP1740EC-LF-P.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MP1740EC-LF-P é adequado para 6 aplicaçãos: Portable Bluetooth Speaker, Compact Consumer Audio Product, Battery-Powered Sound Module, USB-Powered Speaker, IoT Audio Notification Device, Embedded Audio Control Board.
Portable Bluetooth Speaker
The MP1740EC-LF-P fits a compact portable speaker because it combines 3 W output into a 4-ohm load with 91% efficiency in a 1.55 mm by 1.55 mm WLCSP package. Its BTL Class-D output can reduce amplifier losses compared with a linear design, helping preserve battery life during moderate listening levels. The system designer should place the amplifier close to the speaker connector, use the manufacturer-recommended supply bypass and output filtering, and verify that the audio source and speaker load match the verified operating point.
Recomendado
Compact Consumer Audio Product
For a small speaker-enabled consumer product, the MP1740EC-LF-P provides mono Class-D amplification in a compact surface-mount package. The verified 3 W into 4 ohms capability is appropriate for applications that do not require stereo or high-power amplification, while the 91% efficiency helps limit wasted power in a thermally constrained enclosure. The designer should evaluate acoustic output, speaker excursion, supply noise, and thermal rise at the highest sustained volume rather than relying only on the nominal power rating.
Recomendado
Battery-Powered Sound Module
The MP1740EC-LF-P is a candidate for a battery-powered sound module where amplifier efficiency contributes directly to usable runtime. Its verified 91% efficiency and full-bridge Class-D output reduce power loss relative to a comparable linear amplifier, although average consumption still depends on audio content and output level. The power system should be sized for the amplifier's verified 3 W into 4-ohm condition and should include the required local decoupling, speaker protection strategy, and shutdown behavior specified by the manufacturer.
Recomendado
USB-Powered Speaker
A USB-powered speaker can use the MP1740EC-LF-P when the power budget supports the verified 3 W output into a 4-ohm speaker. The device's 91% efficiency is useful in USB-powered systems because it limits amplifier conversion loss, while the small WLCSP package leaves board area for USB power management, controls, and connectors. The designer must verify the USB source's current capability, startup behavior, supply ripple, and the required speaker impedance before using the nominal 3 W rating.
Recomendado
IoT Audio Notification Device
The MP1740EC-LF-P can provide audible notification or alert output in an IoT device when mono Class-D drive is sufficient. Its 3 W capability and 91% efficiency allow a compact speaker amplifier to coexist with control and connectivity circuitry, while the 2 V/V default gain provides a starting point for external input-resistor selection. Firmware-controlled gain, volume limiting, mute behavior, and EMI control should be designed around the manufacturer's application circuit and verified acoustic requirements.
Recomendado
Embedded Audio Control Board
The MP1740EC-LF-P is suitable for an embedded audio control board that needs a small, efficient mono speaker driver rather than a high-power external amplifier. The WLCSP package helps minimize footprint, while the full-bridge output simplifies differential speaker routing when the PCB is designed correctly. Because the supplied data does not include detailed pinout, supply limits, protection features, or filtering values, the board should be validated against the official MP1740 datasheet and the EV1740EC-00A evaluation board.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MP1740EC-LF-P — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MP1740EC-LF-Z |
|---|---|---|
| Package | 9-WLCSP, 1.55 mm x 1.55 mm | 9-WLCSP |
| Brand | Monolithic Power Systems | Monolithic Power Systems |
Principais diferenciais
- High verified efficiency for a compact mono audio amplifier (vs MP1740EC-LF-Z)
- Compact 1.55 mm by 1.55 mm WLCSP implementation (vs MP1740EC-LF-Z)
- Manufacturer-defined 3 W into 4-ohm operating point (vs MP1740EC-LF-Z)
Notas de projeto
Treat the Class-D outputs as a high-current differential pair and route them as a controlled pair from the amplifier to the speaker connection. Keep the BTL return path separate from sensitive input and ground-return paths, and follow the manufacturer evaluation-board layout for WLCSP assembly. The provided data confirms BTL operation but does not provide exact output-filter or trace-width values, so those details must come from the official MP1740 documentation.
Design the supply path around the verified 3 W output into a 4-ohm speaker and 91% efficiency figure, while separately checking the amplifier's actual supply-voltage limits and current consumption from the datasheet. Place local decoupling close to the device and validate startup, mute, and shutdown behavior with the intended speaker and source impedance. Do not estimate battery runtime from peak output power alone; audio duty cycle and average signal level strongly affect the result.
Do not connect a speaker as if MP1740EC-LF-P were a ground-referenced single-ended amplifier. The verified BTL full-bridge output requires a differential speaker connection, and incorrect wiring can damage the amplifier, speaker, or system ground. Also avoid assuming that the -P and -Z suffixes are electrically identical without checking the manufacturer ordering information, pinout, lifecycle status, and exposed-pad requirements.
Informações de conformidade
The supplied verified data does not state RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification status. AEC-Q100 is not applicable based on the supplied product description, which identifies the part as an audio amplifier rather than an automotive-qualified device.
