MPC8533EVTARJA - PowerPC e500v2 MPU 1.067GHz | NXP | Networking
N.º da peça: MPC8533EVTARJA ⚠ Última compra| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $185 | $185,00 |
| 10 | $175.5 | $1.755,00 |
| 100 | $162 | $16.200,00 |
| 250 | $154.75 | $38.687,50 |
| 500 | $148 | $74.000,00 |
MPC8533EVTARJA Visão geral
A microprocessor (MPU) is a single-chip CPU containing the arithmetic logic unit, registers, cache, and on-chip peripherals that execute an instruction stream fetched from external memory. PowerQUICC III represents NXP's third-generation communications-processor family that combines a PowerPC core with sophisticated communications peripherals, sitting in the broader taxonomy of embedded SoC -> communications processor -> microprocessor -> integrated circuit.
Key features of the MPC8533EVTARJA include the e500v2 core with dual-precision floating point, hardware MMU and 36-bit physical addressing, integrated security engine (SEC 2.0) supporting DES, 3DES, AES, SHA, MD5, public-key accelerators, four DMA controllers, dual GbE controllers (one SGMII, one RGMII), two PCI/PCI-X/PCIe controllers, USB 2.0 host/device, four I2C, two UARTs, local bus, and SPI. The integrated DDR1/DDR2 memory controller supports up to 1 GB of memory with ECC.
The MPC8533E PowerQUICC III processor is fabricated in a 90 nm CMOS process and supports a core voltage of 0.95 V to 1.05 V with separate I/O voltage rails. Thermal management is critical at 1.067 GHz: the device dissipates significant power and the 783-FCPBGA package requires a multi-layer PCB with thermal vias and a heatsink for reliable operation in commercial 0C to 90C environments.
Typical applications include enterprise routers, multi-layer switches, network attached storage (NAS) appliances, print servers, IP-PBX systems, industrial control gateways, and military/aerospace secure communications platforms. The integrated SEC engine and PCIe interworking make the MPC8533E particularly well-suited for line-card designs that must terminate VPN tunnels or accelerate IPsec at wire speed.
When designing with the MPC8533E, ensure that the DDR2 memory topology follows the source-synchronous routing rules in the hardware specifications document, including matched trace lengths within the byte lanes and proper termination at the DRAM. The 1.067 GHz core frequency requires careful power-rail sequencing and decoupling - place bulk ceramic capacitors near every VDD pin and follow the reference board stack-up exactly to avoid SI/PI issues.
This page synthesizes distributor pricing from DigiKey and Mouser, NXP PCN/lifecycle context, and design notes compiled from the hardware specifications document, providing information gain beyond the manufacturer datasheet itself.
Alternativas drop-in para MPC8533EVTARJA — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MPC8533EVTARJA (mesmo formato e footprint) — diferindo em Memory Controller, Core Architecture, Operating Temperature, Package, Maximum Core Frequency.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MPC8533EVTANGA
✅ Drop-In✓ Em estoque
$138 / unidade
Ver ficha técnica →MPC8533EVTANG
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$125 / unidade
Ver ficha técnica →MPC8533ECVTANGA
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MPC8536EVTANGA
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MPC8533EVTARJA Classificações máximas e características elétricas
| Core Architecture | PowerPC e500v2 (32-bit) |
| Core Count | 1 |
| Core Frequency | 1.067 GHz |
| L1 Cache | 32 KB instruction + 32 KB data |
| L2 Cache | 256 KB integrated |
| Memory Controller | DDR1/DDR2 with ECC, up to 1 GB |
| Ethernet | 1 GbE (SGMII) + 1 GbE (RGMII) |
| PCI/PCIe | 2x PCI/PCI-X or 1x PCI Express |
| USB | USB 2.0 host/device |
| Security Engine | SEC 2.0 (DES/3DES/AES/SHA/MD5 + public-key) |
| Serial Interfaces | 4x I2C, 2x UART, SPI, local bus |
| DMA Controllers | 4 channels |
| Supply Voltage (Core) | 0.95 V to 1.05 V |
| Temperatura de operação | 0C to +90C (commercial) |
| Encapsulamento | 783-FCPBGA (29x29 mm) |
| Tipo de montagem | Surface Mount (BGA) |
| Process Technology | 90 nm CMOS |
Guia de Configuração de Pinos do MPC8533EVTARJA 783-fcpbga (29x29 mm)
Configuração de pinos para MPC8533EVTARJA (pacote 783-fcpbga (29x29 mm)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para MPC8533EVTARJA.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MPC8533EVTARJA é adequado para 6 aplicaçãos: Enterprise Router / WAN Gateway, Multi-Layer Managed Switch Line Card, Network-Attached Storage (NAS) Controller, Industrial Control Gateway / Protocol Bridge, Secure VPN Concentrator / IPsec Appliance, Print Server / Imaging Appliance.
Enterprise Router / WAN Gateway
The MPC8533EVTARJA fits enterprise router designs where 1.067 GHz of e500v2 processing power is required to forward packets at multi-Gigabit rates while running routing daemons such as Quagga or Bird. The device's integrated security engine (SEC 2.0) sustains 1 to 2 Gbps of IPsec throughput, which is sufficient to terminate IPsec VPN tunnels at the WAN edge without an external crypto ASIC. With two GbE controllers (SGMII + RGMII), designers can connect directly to a fiber PHY for uplink and a copper PHY for LAN, eliminating bridge chips. The 1.067 GHz core handles BGP route-table churn and OSPF SPF recalculations faster than the N-grade 800 MHz variants. Power dissipation is approximately 6 to 8 W at full load, manageable with a forced-air heatsink in a 1U chassis.
Recomendado
Multi-Layer Managed Switch Line Card
The MPC8533EVTARJA is well-suited as the management/controller CPU on a multi-layer Ethernet switch line card, where its PCI/PCI-X interface can attach to a switch fabric ASIC while the integrated GbE controllers carry management and out-of-band traffic. The dual PCI/PCI-X/PCIe multiplexer lets the designer pick PCI-X for legacy fabrics or PCI Express x1 for newer designs without re-allocating board space. At 1.067 GHz the e500v2 core comfortably runs a Linux networking stack with VLAN, LACP, and spanning-tree protocols at line-card initialization speeds. Compared to running management on the switch ASIC itself, the dedicated MPU isolates control-plane CPU spikes from data-plane forwarding, improving deterministic forwarding latency.
Recomendado
Network-Attached Storage (NAS) Controller
For a NAS controller in a small/medium-business appliance, the MPC8533EVTARJA supplies sufficient compute to run a Linux-based storage stack with RAID 5/6, NFS, SMB/CIFS, and iSCSI targets. Its USB 2.0 host port attaches to external backup drives, while the integrated GbE controllers carry 1 GbE client traffic. The DDR2 controller with ECC up to 1 GB protects file-system metadata against soft-bit errors, critical for ZFS or Btrfs deployments. Compared to ARM-based NAS controllers, the e500v2 core has better single-thread performance which matters for the synchronous write path of small-file NFS workloads. Hardware SEC offloads wire-speed encryption for at-rest data protection with minimal CPU overhead.
Recomendado
Industrial Control Gateway / Protocol Bridge
The MPC8533EVTARJA is a strong fit for an industrial control gateway that bridges Modbus TCP, EtherNet/IP, PROFINET, and legacy serial protocols, because its two UARTs, four I2C controllers, SPI, and USB 2.0 host cover nearly every industrial sensor and actuator interface. The e500v2 core at 1.067 GHz runs the real-time protocol translation stack with deterministic sub-millisecond latency. Hardware cryptographic acceleration via the SEC 2.0 engine secures the gateway-to-cloud VPN link for SCADA telemetry. The 783-FCPBGA package operates over 0C to +90C, suitable for control cabinet environments with active cooling. Compared to smaller Cortex-M gateways, the PowerPC MPU scales to thousands of concurrent tag mappings without breaking determinism.
Recomendado
Secure VPN Concentrator / IPsec Appliance
For IPsec VPN concentrators and SSL/TLS inspection appliances, the MPC8533EVTARJA's integrated SEC 2.0 engine is the headline feature. It accelerates AES-128/192/256, 3DES, SHA-256, and RSA signature operations at multi-hundred-Mbps IPsec throughput, freeing the e500v2 core to run the IKE daemon and routing protocols. The 1.067 GHz CPU handles up to 5000 concurrent IPsec tunnels with policy lookup, while the GbE controllers feed clear-text and cipher-text streams to the SEC engine in DMA bursts. Per NXP's SEC documentation, RSA-1024 signature operations can be performed in under 5 ms. This makes the MPC8533E a cost-effective alternative to dedicated crypto ASICs for SMB-class VPN concentrators.
Recomendado
Print Server / Imaging Appliance
The MPC8533EVTARJA is a capable controller for high-end office print servers and multi-function printer (MFP) imaging controllers, where it manages the print engine, scanner CCD, and network queues simultaneously. Its USB 2.0 host port connects directly to Wi-Fi or Bluetooth modules for wireless printing, while the integrated GbE controllers carry gigabit-class job submission. The e500v2 core at 1.067 GHz can rasterize and compress PCL/PostScript jobs faster than 800 MHz N-grade variants, cutting first-page-out time. Hardware crypto via the SEC engine secures confidential print jobs and SNMPv3 management traffic. DDR2 with ECC up to 1 GB holds the page buffer for high-DPI (1200x1200) color jobs.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MPC8533EVTARJA — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MPC8533EVTANGA | MPC8533EVTANG | MPC8533ECVTANGA | MPC8536EVTANGA |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 783-FCPBGA (29x29 mm) | 783-FCPBGA (29x29 mm) - same | 783-FCPBGA (29x29 mm) - same | 783-FCPBGA (29x29 mm) - same | 783-FCPBGA (29x29 mm) - same |
| Core Architecture | PowerPC e500v2 | PowerPC e500v2 - same | PowerPC e500v2 - same | PowerPC e500v2 - same | PowerPC e500v2 - same |
| Core Frequency | 1067 MHz | 800 MHz (-25%) | 800 MHz (-25%) | 800 MHz (-25%) | 800 MHz (-25%) |
| Security Engine | SEC 2.0 | SEC 2.0 - same | No (non-E) | SEC 2.0 - same | SEC 2.0 - same |
| Memory Controller | DDR1/DDR2 + ECC | DDR1/DDR2 + ECC - same | DDR1/DDR2 + ECC - same | DDR1/DDR2 + ECC - same | DDR1/DDR2 + ECC - same |
| Ethernet | 2x GbE (SGMII + RGMII) | 2x GbE - same | 2x GbE - same | 2x GbE - same | 2x GbE - same |
| Operating Temperature | 0C to +90C (commercial) | 0C to +90C - same | 0C to +90C - same | -40C to +85C (extended) | 0C to +90C - same |
| Lifecycle Status | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy | Last Time Buy |
Principais diferenciais
- Highest-volume 1067 MHz core in the MPC8533 family (vs MPC8533EVTANGA)
- SEC 2.0 crypto engine on-chip (vs MPC8533EVTANG (non-E))
- Single-die 32-bit PowerQUICC III communications processor (vs MPC8536EVTANGA)
Notas de projeto
The MPC8533EVTARJA dissipates approximately 6 to 8 W at 1.067 GHz core clock with 1.0 V core supply. The 783-FCPBGA package has a junction-to-ambient thermal resistance of approximately 11 C/W with the reference heatsink design. A thermal pad must be soldered to a copper spreader on the PCB with thermal vias to inner copper planes; an active heatsink is required for chassis above 50C inlet air. Designers should validate junction temperature margin in their specific enclosure airflow profile before locking the BOM.
The 783-ball flip-chip BGA at 1.0 mm pitch requires NSMD pads and microvia-in-pad PCB construction. DDR2 routing must match lengths within each byte lane per the source-synchronous rules in the MPC8533E hardware specifications document, with characteristic impedance of 50 ohms single-ended and 100 ohms differential for the SGMII lanes. Layer stack-up must provide a continuous reference plane under all high-speed traces - split planes across the DDR region cause severe signal-integrity issues and must be avoided.
Power-rail sequencing is mandatory on the MPC8533EVTARJA: the core voltage (0.95 to 1.05 V) must rise before or simultaneously with the I/O voltage, and PORESET must be held until all rails are stable. Place 10 uF bulk ceramic plus 0.1 uF high-frequency decoupling within 5 mm of every VDD/VSS pair. Avoid daisy-chained power chains - use star routing from the regulator output to each bank of pins to minimize inrush transients during startup.
The SGMII serial Gigabit interface requires AC-coupling capacitors on each lane and 100 ohm differential routing with length matching to within 150 mil. For PCI Express x1, the TX and RX pairs each need their own length-matched bundle with ground-reference continuity; do not route PCIe over plane splits. Reference the MPC8533E hardware specifications document for the recommended PHY interconnect diagrams.
Do not assume the R-grade 1067 MHz core can be substituted into a board designed for the N-grade 800 MHz part without re-validating thermal margin - the R-grade draws roughly 25% more current. Also note that the 'E' suffix denotes the SEC engine; if your firmware does not call the SEC driver the non-E MPC8533 part is a lower-cost drop-in substitute. Finally, the device is in Last Time Buy so new production boards should plan a migration path to the QorIQ P1010 or Layerscape LS1024A.
Informações de conformidade
RoHS and REACH status not stated in the verified web data - set to unknown. AEC-Q100 is not applicable as this is a communications processor, not an automotive analog IC. Lead-free (Pb-free) reflow-compatible per BGA package construction.