PCA9535HFHP - 16-Bit I2C GPIO Expander | NXP
N.º da peça: PCA9535HFHP ✓ AtivoPCA9535HFHP Visão geral
An I/O expander is an interface IC that translates serial I2C commands into parallel digital input and output signals. It sits between a microcontroller or application processor and external peripherals, reducing the number of GPIO pins required on the host. The PCA9535HFHP supports the same fixed I2C address as the PCA9555, allowing up to eight PCA9535 and PCA9555 devices to share one bus in any combination.
The device provides 16 general-purpose I/O lines, an active-low interrupt output, and separate input/output configuration registers. Its principal electrical identifiers are a 16-bit port width, I2C/SMBus compatibility, 400 kHz bus operation, and a 24-pin HWQFN package. The PCA9535HFHP is a low-power version of the PCA9555 and is intended for designs that need more digital I/O without adding another high-pin-count host controller.
Internally, the expander uses a serial-to-parallel control architecture: the host writes configuration, output, and polarity-control data over I2C, while the interrupt output indicates a change on an input port. Register-based operation allows pins to be configured individually as inputs or outputs. Because the device uses a fixed address, multiple expanders can coexist on the same bus without I2C address straps, provided address strapping is not required by the host design.
Typical applications include control-panel GPIO expansion, relay and LED interface boards, sensor and switch aggregation, keyboard or keypad scanning, industrial automation modules, and compact consumer peripherals. The interrupt output reduces polling overhead when a large number of expander inputs must be monitored by the host processor.
PCB layout should preserve short, clean traces for I2C, provide adequate ground return paths, and place pull-up resistors near the bus master when bus capacitance is high. The exposed-pad version requires a thermal and electrical land pattern consistent with its manufacturer package drawing, including solder mask and paste design that meet the package assembly rules.
This page combines package, interface, application, and replacement guidance with a structured comparison of pin-compatible options, helping engineers shorten component-selection and board-layout work before committing to a production design.
Alternativas drop-in para PCA9535HFHP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
PCA9555AHF,128
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCA9535BS
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCA9535HFHP Especificações
| Função | 16-bit I2C-bus/SMBus I/O expander with interrupt |
| Number of I/O Ports | 16 bits |
| I2C Maximum Bus Frequency | 400 kHz |
| Interface Compatibility | I2C-bus and SMBus |
| Encapsulamento | 24-HWQFN (4 x 4 mm) |
| Number of Terminals | 24 |
| Tipo de montagem | Surface mount |
| Faixa de temperatura de operação | -40 C to +85 C |
| Interrupt Output | Yes |
| Device Type | Low-power I/O port expander |
| I2C Address | Fixed address, same as PCA9555 |
| Maximum Devices per I2C Bus | Up to 8 PCA9535/PCA9555 devices in any combination |
Guia de Configuração de Pinos do PCA9535HFHP 24-hwqfn (4 x 4 mm)
Configuração de pinos para PCA9535HFHP (pacote 24-hwqfn (4 x 4 mm)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para PCA9535HFHP.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PCA9535HFHP é adequado para 6 aplicaçãos: Industrial Control Panel GPIO Expansion, LED and Relay Interface Board, Sensor and Switch Aggregation, Keypad and Human Interface Expansion, Remote Sensor Hub, Consumer Peripheral and Appliance Interface.
Industrial Control Panel GPIO Expansion
The PCA9535HFHP fits an industrial control panel that needs more switch inputs and indicator outputs than the host controller provides. Its 16 configurable ports operate through one I2C or SMBus connection at up to 400 kHz, while the interrupt output lets the controller respond to a changed input instead of polling every line continuously. The 24-HWQFN 4 x 4 mm package saves board area in densely populated controller assemblies, and the -40 C to +85 C operating range covers typical industrial environments. Use a suitable driver stage for relays or high-current loads rather than driving them directly from the expander.
Recomendado
LED and Relay Interface Board
Use the PCA9535HFHP as the output controller on a separate LED or relay interface board connected to a main processor. Its 16 ports provide a compact way to control status LEDs, latches, or driver-enable signals while keeping the high-current switching devices away from the host board. Because I2C updates can refresh multiple output bits with one register write, repetitive display or relay-state changes become efficient. Verify each port's output-drive capability in the NXP data sheet and use transistors, MOSFETs, or suitable drivers whenever the load exceeds the GPIO limits.
Recomendado
Sensor and Switch Aggregation
The PCA9535HFHP is suitable for aggregating switches, limit sensors, and digital status lines from a remote panel. Sixteen I/O ports reduce the pin count required on the host and allow the expander to sit close to the sensed devices, which can shorten signal traces. Its interrupt output provides an efficient wake-up mechanism for change-driven systems, and its low-power designation supports battery-operated or energy-conscious equipment. Keep input traces away from switching nodes and use the package's exposed-pad land pattern according to the manufacturer drawing.
Recomendado
Keypad and Human Interface Expansion
The PCA9535HFHP can expand a microcontroller's available lines for keypad scanning, rotary-switch decoding, or additional front-panel buttons. Its 16-bit port structure allows multiple interface functions to share one I2C connection, and the interrupt output can indicate a matrix change when the application uses it that way. The 4 x 4 mm HWQFN package is especially useful where the human-interface board is compact. Validate the input levels and timing for the scanning scheme, and debounce mechanically noisy contacts in firmware or with suitable external components.
Recomendado
Remote Sensor Hub
The PCA9535HFHP works well in a remote sensor hub that must collect several digital enable, alarm, or presence signals while forwarding them to a central controller. Its fixed I2C address supports sharing the bus with up to eight compatible PCA9535 or PCA9555 devices in any combination, which simplifies multi-board expansion without address-strapping requirements. The interrupt output reduces unnecessary serial polling, while low-power operation benefits portable installations. Confirm the supply range and per-pin current in the manufacturer data sheet before deploying the hub in the field.
Recomendado
Consumer Peripheral and Appliance Interface
The PCA9535HFHP is appropriate for consumer peripherals and appliances that need multiple low-speed control lines but have limited host GPIO. It can operate LEDs, mode switches, interlocks, and auxiliary sensors through a compact serial interface, reducing connector count and main-board complexity. Its -40 C to +85 C range covers typical indoor environments, and the interrupt output allows the controller to react promptly to user or system events. Follow the manufacturer layout guidance for the exposed pad and provide the I2C pull-up arrangement appropriate for the complete bus.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PCA9535HFHP — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PCA9555AHF,128 | PCA9535BS |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 24-HWQFN (4x4) | 24-HWQFN (4x4) | 24-HWQFN (4x4) |
| Function | 16-bit I2C/SMBus GPIO expander with interrupt | 16-bit I2C/SMBus GPIO expander with interrupt | 16-bit I2C/SMBus GPIO expander with interrupt |
| Maximum I2C Bus Frequency | 400 kHz | 400 kHz | 400 kHz |
| Power Profile | Low-power version of PCA9555 | Standard PCA9555 power profile | Low-power I/O expander |
| I2C Address | Fixed; same as PCA9555 | Fixed; same as PCA9535 | Fixed; same as PCA9555 |
| Interrupt Output | Yes | Yes | Yes |
| Number of I/O Ports | 16 | 16 | 16 |
Principais diferenciais
- Lower-power positioning within the same NXP expander family (vs PCA9555AHF,128)
- Sixteen configurable ports with interrupt support (vs PCA9535BS)
- Compact surface-mount integration (vs PCA9555AHF,128)
Notas de projeto
Follow the NXP package drawing for the 24-HWQFN 4 x 4 mm land pattern, exposed-pad connection, solder-mask opening, and paste stencil. Do not route high-current or fast-switching return currents beneath the expander. Place the device near the connector or controlled signals it serves so the 16 I/O traces remain short and are not forced to cross unrelated bus or power routes.
Design the I2C bus as a robust shared communication network rather than a point-to-point trace. Route SCL and SDA away from noisy switching nodes, keep both lines reasonably matched in length, and verify pull-up placement against the complete bus capacitance and speed. If several PCA9535 or PCA9555 devices share the fixed address, confirm that no address-strap configuration is required by the host firmware.
Do not assume every alternative is interchangeable at the electrical level. PCA9555AHF,128 is pin-compatible for many I2C-to-GPIO applications, but it is not the low-power version of PCA9535HFHP. Before substitution, compare supply voltage, I/O drive current, timing, and operating current in the manufacturer data sheets. Firmware should also be checked for any device-specific register or initialization behavior.
Use the interrupt output to reduce unnecessary host polling when monitoring multiple inputs, but retain polling as a timeout or fallback if the interrupt line can become disconnected. For battery-powered systems, compare the standby and active current of the selected expander because the PCA9535 low-power designation and the standard PCA9555 behavior may produce different system-level consumption.
Informações de conformidade
The manufacturer and distributor pages identify the device as an active NXP 16-bit I2C/SMBus I/O expander, but no explicit compliance declarations were stated. Confirm RoHS, REACH, AEC-Q100, halogen-free, and conflict-minerals status from the current NXP product documentation before qualification.