Texas Instruments

PCA9539PWG4 - 16-Bit I/O Expander | Texas Instruments

N.º da peça: PCA9539PWG4 ✓ Ativo
2.3 V to 5.5 V Vdss 24-pin TSSOP Package 400 kHz Speed
MOQ: 1 |

PCA9539PWG4 Visão geral

The Texas Instruments PCA9539PWG4 is a 16-bit I2C/SMBus remote I/O expander operating from 2.3 V to 5.5 V, supporting bus speeds up to 400 kHz and packaged in a 24-pin TSSOP. The device provides 16 general-purpose input or output lines, an interrupt output, reset control, and configuration registers for compact peripheral expansion.

An I/O expander is an interface IC that increases the number of digital input and output pins available to a host microcontroller. In the hierarchy of semiconductor devices, the PCA9539 belongs to the I/O expander class of interface controllers. It communicates with a host through the two-wire I2C or SMBus serial interface while driving or reading a separate group of 16 parallel I/O lines. This architecture reduces microcontroller pin count without requiring a high-speed parallel peripheral bus.

The PCA9539 supports a 2.3 V to 5.5 V operating range and a maximum I2C/SMBus frequency of 400 kHz. Its 16 I/O channels can be configured through registers, while dedicated interrupt and reset functions simplify event-driven system design. The manufacturer product page identifies the device as a low-power SMBus I/O expander with interrupt, reset, and configuration registers. Unlike the closely related PCA9555, the PCA9539 does not include the internal I/O pull-up resistors.

The absence of internal I/O pull-ups can reduce power consumption when output ports are held low. This behavior is useful in systems that provide their own pull-ups or use open-drain downstream circuitry. However, external pull-up resistors may be required where a defined input or bus state is needed. The RESET input provides a hardware mechanism for restoring the registers to their default configuration, while the interrupt output allows a host to respond when a configured input changes state.

Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, communication equipment, and compact embedded systems that need more digital lines than the host controller provides. The 24-pin TSSOP package is also suitable for leaded, through-hole industrial assemblies where a surface-mount QFN package would be unsuitable. Designers should verify the exact I/O electrical limits, address options, and pin mapping in the manufacturer datasheet before finalizing a PCB.

When implementing the PCA9539, place its pull-up components close to the bus master and keep the I2C routing away from high-current switching paths. Confirm that every port pin's input, output, pull-up, and current-limit requirements match the external circuit. Register programming should also account for the device's reset state and the timing relationship between reset release, bus communication, and the first port operation.

This component guide combines device specifications, package guidance, application analysis, selection criteria, and verified drop-in alternatives. It also highlights the distinction between the PCA9539 and PCA9555 so engineers can select the correct expander when internal pull-ups, reset behavior, or address decoding affect the design.

Alternativas drop-in para PCA9539PWG4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

PCA9539PWG4

✅ Drop-In
Texas Instruments
📦 24-pin TSSOP
16-bit remote I/O expander · 16 lines · I2C/SMBus · 400 kHz · 2.3 V to 5.5 V · -40 C to +85 C · 24-pin TSSOP · 24 pins

Consulte o preço

Ver ficha técnica →

PCA9539PW,118

✅ Drop-In
📦 24-pin TSSOP
Same 16 I/O lines, 2.3 V to 5.5 V operating class, 400 kHz bus, and 24-pin TSSOP format; manufacturer-specific register and timing details require comparison.

📋 Alternativa de referência (fora do catálogo)

PCA9539PWG4 Especificações

Device Type 16-bit remote I/O expander
Number of I/O Lines 16 lines
Serial Interface I2C/SMBus
Maximum Bus Frequency 400 kHz
Tensão de alimentação de operação 2.3 V to 5.5 V
Temperatura de operação -40 C to +85 C
Encapsulamento 24-pin TSSOP
Número de pinos 24 pins
Estilo de montagem Gull-wing, surface mount
Temperature Grade Industrial
Interrupt Output 1 interrupt output
Reset Function Dedicated reset input
Configuration Registers Register-configurable I/O channels
Internal I/O Pull-Up Resistors Not included
Status RoHS Compliant

Guia de Configuração de Pinos do PCA9539PWG4 24-pin tssop

Configuração de pinos para PCA9539PWG4 (pacote 24-pin tssop). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 24-pin tssop para PCA9539PWG4

Nenhum dado detalhado de pinagem disponível para PCA9539PWG4.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

PCA9539PWG4 é adequado para 6 aplicaçãos: Industrial Control and Relay Interface, Sensor Hub and Condition Monitoring, Communication Equipment Status Control, Programmable Controller Front Panel, LED and Lighting Control, Secure and Surveillance Peripheral Control.

🏭

Industrial Control and Relay Interface

The PCA9539PWG4 fits industrial control boards that need additional relay, valve, interlock, or digital status lines without dedicating host-controller pins. Its 16 configurable I/O lines can operate as outputs for actuators or inputs for switch state monitoring, while the interrupt output lets the controller respond to a selected input event instead of polling continuously. The 2.3 V to 5.5 V operating range supports common industrial logic levels, and the 400 kHz I2C/SMBus interface is sufficient for control updates rather than high-bandwidth data transfer. Because the device has no internal I/O pull-ups, add suitable external resistors where the attached relay driver, opto-isolator, or input circuit needs a defined inactive state. Validate isolation, flyback protection, and ground current at the interface rather than treating the expander as the actuator driver itself.

🧩

Sensor Hub and Condition Monitoring

The PCA9539PWG4 is useful in a sensor hub where discrete sensors, alarm inputs, and configuration switches exceed the available GPIO of a small microcontroller. Its 16-bit port structure supports mixed input and output assignments, while reset establishes a known hardware state and the interrupt line can notify the host of an important change. The 400 kHz serial interface provides sufficient control bandwidth for status polling and configuration updates. Because the PCA9539 lacks internal I/O pull-ups, external pull-ups may be required for open-drain sensor outputs or dry-contact inputs. Keep sensitive sensor analog paths physically separated from the expander and relay wiring, and use the interrupt signal to wake or prioritize the controller rather than using it as a high-frequency data path.

🌐

Communication Equipment Status Control

The PCA9539PWG4 can expand discrete status and control signals in network-interface, gateway, and communication equipment. Typical assignments include module-present, link-enable, alarm, fan-control, and user-indicator lines, allowing the communications processor to monitor several events over its I2C/SMBus interface. The 24-pin TSSOP package is convenient for leaded industrial boards, while the 2.3 V to 5.5 V supply range supports 3.3 V and 5 V logic environments. The interrupt output improves responsiveness by reporting a configured input change without continuous register reads. External pull-ups should be fitted where a defined state is required, and the bus layout should minimize trace length and capacitance. The 400 kHz bus ceiling is appropriate for configuration traffic, not for transferring large diagnostic data streams.

🔧

Programmable Controller Front Panel

The PCA9539PWG4 supports front-panel I/O in programmable controllers and compact automation systems where LEDs, pushbuttons, selectors, and interlock signals would otherwise consume most host GPIO. The 16 channels can be mixed between output and input operation through the configuration registers, allowing indicator LEDs and user buttons to share one expansion device. A 2.3 V to 5.5 V operating range accommodates common control-board voltage levels, and the interrupt line supports immediate feedback from a button or interlock change. Since internal I/O pull-ups are absent, the design should provide external pull-ups where switches are open or the inputs require a defined inactive level. Use current-limiting resistors for LEDs and confirm the electrical limits for the intended logic family before finalizing the front-panel schematic.

💡

LED and Lighting Control

The PCA9539PWG4 can organize digital lighting commands and status indicators in display, signage, and lighting modules. Sixteen outputs can drive suitable digital control inputs, fault indicators, or relay-enable stages while a smaller portion of the port handles keypad or fixture-status inputs. Its 24-pin TSSOP package is easy to inspect and rework in leaded production assemblies, while the I2C/SMBus interface allows a host to update multiple outputs through a compact command sequence. The 400 kHz limit comfortably supports normal configuration traffic. Do not use the PCA9539 as a direct constant-current LED driver without checking its per-pin current limit and output-driver characteristics; use suitable transistor stages for higher current. External pull-ups may be needed on inputs, and the absence of internal pull-ups should be included in the system-level power-budget calculation.

🎥

Secure and Surveillance Peripheral Control

The PCA9539PWG4 can provide auxiliary discrete I/O in a surveillance or access-control peripheral, including tamper-contact inputs, door-status sensing, indicator control, and relay commands. The interrupt output supports event-driven handling of a door or tamper transition, which is more efficient than continuous polling. The 2.3 V to 5.5 V operating range makes the expander suitable for common embedded security controllers, and the 24-pin TSSOP package simplifies through-hole construction. Since the device does not contain internal I/O pull-ups, security-related open-contact inputs may need appropriately sized external resistors to prevent floating states. Keep security isolation boundaries and tamper wiring outside the expander's general logic domain, and validate the complete system for false activation, reset behavior, and power-loss states.

What is the PCA9539PWG4 used for?
The PCA9539PWG4 is a 16-bit remote I/O expander that adds 16 configurable digital lines to a host through an I2C or SMBus serial interface. According to the Texas Instruments product page, it includes interrupt, reset, and configuration registers. It is useful when a microcontroller, application processor, or programmable controller has too few direct I/O pins for relays, indicators, switches, or digital sensors.
What is the operating voltage of the PCA9539PWG4?
The PCA9539PWG4 operates from 2.3 V to 5.5 V, allowing it to interface with both 3.3 V and 5 V systems. The Texas Instruments product page identifies this supply range for the PCA9539 family. The host controller and pull-up arrangement still must be compatible with the selected bus voltage, particularly when the I/O port operates independently of the serial-interface voltage.
How many I/O pins does the PCA9539PWG4 provide?
The PCA9539PWG4 provides 16 configurable I/O lines in a 24-pin TSSOP package. The lines are organized as two 8-bit ports and can be assigned as inputs or outputs through configuration registers. The exact input thresholds, output-current limits, and per-pin drive behavior should be checked in the manufacturer datasheet for the attached external circuitry.
What bus speed does the PCA9539PWG4 support?
The PCA9539PWG4 supports I2C and SMBus communication at up to 400 kHz. The DigiKey listing for this exact MPN identifies a 400 kHz I/O expander in a 24-pin TSSOP package. Practical bus performance also depends on wiring length, pull-up resistance, bus capacitance, and the operating characteristics of every device connected to the same bus.
Does the PCA9539PWG4 have internal I/O pull-ups?
No. The Texas Instruments product page states that the PCA9539 differs from the PCA9555 by removing the internal I/O pull-up resistors. This can reduce current consumption when I/O lines are held low, but external pull-ups may be necessary where the application requires a defined inactive state. Select pull-up values from the bus capacitance and required rise time.
Where can I download the PCA9539PWG4 datasheet PDF?
The official PCA9539PWG4 documentation is available through the Texas Instruments product page at https://www.ti.com/product/PCA9539, which links the manufacturer datasheet, ordering information, and quality documentation. Use the manufacturer document for the authoritative register map, pin descriptions, electrical limits, timing diagrams, and package drawing before laying out or programming the device.
Where can I find the PCA9539PWG4 pinout?
The PCA9539PWG4 pinout is published in the pin-configuration section of the Texas Instruments PCA9539 datasheet. The exact device uses a 24-pin TSSOP package, and the manufacturer datasheet is the correct place to confirm every port pin, power pin, address input, reset input, interrupt output, and ground connection. Assign PCB tracks from that pin table rather than relying on a generic TSSOP drawing.
Where can I buy the PCA9539PWG4 and check its price?
Use the Request a Quote form on this page to ask for the PCA9539PWG4, current commercial terms, and available quantity. The form is the appropriate route for current pricing, stock, minimum order quantity, and lead-time confirmation because market conditions and inventory change continuously. Provide the exact PCA9539PWG4 ordering code to avoid receiving a functionally similar but differently suffixed part.
How long is the PCA9539PWG4 lead time?
The current lead time for the PCA9539PWG4 should be requested through the Request a Quote form on this page. Lead time can vary with the exact order quantity, package availability, production scheduling, and shipment destination. For a production design, provide the forecast quantity and required delivery date when submitting the request so the supplier can confirm the appropriate schedule.
Is the PCA9539PWG4 in stock?
Current PCA9539PWG4 inventory should be confirmed through the Request a Quote form on this page. A live distributor result does not establish a guaranteed stock quantity for a future order, particularly when quantities span multiple production lots. Include the required reel quantity, shipment date, and inspection requirements in the request to establish a usable supply commitment.
What is the difference between PCA9539PWG4 and PCA9539PW,118?
The PCA9539PWG4 is the Texas Instruments order code, while PCA9539PW,118 is the NXP order code for a comparable 16-bit, 400 kHz I2C/SMBus expander in a 24-pin TSSOP. The manufacturer relationships are different, and software should still validate the device identifier, register behavior, reset timing, address decoding, and electrical characteristics. The cross-brand part is the closer alternative to evaluate when sourcing flexibility matters.
When should I choose the PCA9539PWG4 over another 16-bit I/O expander?
Choose the PCA9539PWG4 when the design needs a 2.3 V to 5.5 V I2C/SMBus expander with 16 configurable I/O lines, a 400 kHz bus, reset control, and an interrupt output in a 24-pin TSSOP. It is especially suitable when the absence of internal I/O pull-ups is acceptable or beneficial. Select another model only if it offers a required feature such as integrated pull-ups, different address behavior, or a preferred package.
Can PCA9539PW,118 replace the PCA9539PWG4 on an existing PCB?
PCA9539PW,118 is a candidate drop-in replacement because the NXP listing describes a 16-bit I2C/SMBus I/O expander with 400 kHz operation in a 24-pin TSSOP. Before production substitution, compare the complete pin table, address pins, reset behavior, interrupt polarity, register map, electrical limits, and power consumption against the Texas Instruments datasheet. Firmware should also verify the expected device identity.
What can replace the PCA9539PWG4?
The strongest documented replacement candidate is NXP PCA9539PW,118, which shares the 16-bit, 400 kHz I2C/SMBus function and 24-pin TSSOP format. No other complete pin-compatible substitute is established by the available manufacturer and distributor documentation, so a broader replacement cannot be declared drop-in without validation. Review the register map and electrical differences before approving a second source.
What are the key specifications engineers should know about the PCA9539PWG4?
The principal PCA9539PWG4 specifications are 16 configurable I/O lines, a 2.3 V to 5.5 V operating range, I2C/SMBus communication up to 400 kHz, and a 24-pin TSSOP package. It also provides an interrupt output, reset input, and configuration registers but omits the internal I/O pull-ups found in the PCA9555. These features make it suitable for low-power embedded peripheral expansion.

Dados de referência de engenharia para PCA9539PWG4 — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the PCA9539PWG4 when the design needs 16 configurable I/O lines, a 2.3 V to 5.5 V supply range, 400 kHz I2C/SMBus communication, and a 24-pin TSSOP package with reset and interrupt functions. Its lack of internal I/O pull-ups can reduce current in circuits that hold outputs low, although external pull-ups may then be necessary. Consider NXP PCA9539PW,118 when a second-source 24-pin TSSOP candidate is useful, but compare the pin table, register map, address options, reset timing, interrupt polarity, and electrical characteristics before substituting it. Do not select the PCA9555 as a direct replacement when its integrated pull-ups alter the current budget or pin behavior. For designs requiring a different I/O count, voltage architecture, address scheme, or package, select a purpose-built expander rather than assuming functional compatibility means drop-in compatibility.

Comparação com alternativas

Parâmetro Este produto PCA9539PWG4 PCA9539PW,118
Brand Texas Instruments Texas Instruments NXP Semiconductors
Package 24-pin TSSOP 24-pin TSSOP 24-pin TSSOP
I/O Count 16 lines 16 lines 16 lines
Serial Interface I2C/SMBus I2C/SMBus I2C/SMBus
Maximum Bus Frequency 400 kHz 400 kHz 400 kHz

Principais diferenciais

  • Lower-power architecture through omitted internal I/O pull-ups (vs PCA9555)
  • Wide 2.3 V to 5.5 V operating range (vs PCA9539PW,118)
  • Dedicated reset and interrupt functions in a 24-pin TSSOP (vs PCA9539PW,118)

Notas de projeto

Do not assume that the PCA9539 can replace the PCA9555 without accounting for pull-up differences. The Texas Instruments product page identifies the PCA9539 as lacking the PCA9555 internal I/O pull-up resistors. Add external pull-ups wherever an open-drain or dry-contact circuit must have a defined inactive state, and select each resistance from the required rise time, bus capacitance, sink-current limit, and downstream device specification.

Place the device close to the connector or controlled peripheral group, while keeping the two-wire serial route away from switching nodes and relay-coil wiring. Route SDA and SCL consistently, minimize stubs, and place any required pull-up resistors near the master or the electrically strongest bus node. Use a continuous ground reference beneath the TSSOP and return high-current actuator currents directly to the supply plane rather than through the expander's ground path.

Budget the power loss from the external pull-up network separately from the expander's internal consumption. When an external resistor pulls a line high, a logic-low output can continuously dissipate voltage multiplied by current through that resistor. Estimate this value using the actual logic-low voltage and resistor value, then check it against the package dissipation limit and the board's overall standby-power target.

Informações de conformidade

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The component listing identifies a green plastic TSSOP and includes RoHS as a feature. No separate REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declaration is stated.

Dados verificados em: 2026-11-14 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

PCA9539PWG4 datasheet PCA9539PWG4 pinout PCA9539PWG4 datasheet pdf PCA9539PWG4 specifications PCA9539PWG4 equivalent PCA9539PWG4 replacement PCA9539PWG4 price PCA9539PWG4 stock Texas Instruments PCA9539PWG4 PCA9539PWG4 24-TSSOP PCA9539PWG4 16-bit I/O expander PCA9539PWG4 vs PCA9539PW,118 PCA9539PWG4 application circuit PCA9539PWG4 cross reference

Componentes & termos relacionados

Texas Instruments PCA9539PWG4 PCA9539PW,118 NXP Semiconductors PCA9539 PCA9555 I/O expander interface IC semiconductor I2C SMBus 16-bit parallel I/O interrupt output reset input configuration registers 2.3 V to 5.5 V operating voltage 400 kHz bus speed TSSOP-24 TSSOP package family surface-mount device RoHS industrial control sensor hub lighting control
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ