NXP Semiconductors

PCF8574P - 8-Bit 100kHz I2C I/O Expander | NXP

N.º da peça: PCF8574P ✓ Ativo
2.5 V to 6 V Vdss 16-pin DIP Package 100 kHz Speed
MOQ: 1 |

PCF8574P Visão geral

The NXP Semiconductors PCF8574P is an 8-bit remote I/O expander for the two-wire bidirectional I2C-bus, with a 100 kHz bus interface, three hardware address inputs, eight quasi-bidirectional ports, and an interrupt output in a 16-pin DIP package. It operates from a 2.5 V to 6 V supply.

An I/O expander is an interface IC that increases the number of general-purpose input and output pins available to a host microcontroller. The PCF8574P uses serial clock and serial data lines to transfer port data over I2C, while the eight parallel port pins connect directly to switches, LEDs, indicators, keypads, or other external circuitry. Its place in the component hierarchy is interface IC, then I/O expander, then peripheral expansion device.

The PCF8574P provides 8-bit port control, 100 kHz I2C operation, three address-selection inputs, and an active-low open-drain interrupt output. The three address inputs allow multiple expanders to share the same SDA and SCL bus. The interrupt output lets a controller identify a change on an input port without continuously polling every expander. These features suit systems that need additional GPIO but have limited direct pins on the host controller.

The device consists of an 8-bit quasi-bidirectional port and an I2C interface. Each quasi-bidirectional port can be configured as an input or output, although outputs have a limited drive capability compared with general-purpose push-pull microcontroller pins. Pull-up resistors are required for open-drain I2C lines, and the external bus design must account for capacitance, pull-up strength, voltage compatibility, and the number of connected devices.

Typical applications include Arduino-compatible control boards, ESP32-based IoT controllers, LED and key-matrix interfaces, relay-control modules, industrial automation equipment, and embedded products requiring eight additional GPIO lines. The PCF8574P is especially useful when adding a modest number of pins is preferable to selecting a host microcontroller with a larger pin count or redesigning the main board.

For reliable operation, connect SDA and SCL to their required pull-ups and do not exceed the 2.5 V to 6 V operating range. Quasi-bidirectional inputs are internally pulled high, so external circuitry must actively sink the relevant port low to register a logic-low state. Confirm output-current requirements and bus timing before driving heavier loads.

This page combines manufacturer specifications, interface behavior, pin-level guidance, practical design notes, and same-package alternatives to support device selection, PCB layout, firmware planning, and sourcing decisions.

Alternativas drop-in para PCF8574P — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com PCF8574P (mesmo formato e footprint) — diferindo em Package, Supply Voltage Range, Device Type, I2C Bus Frequency, Interface.

Texas Instruments
Package: 16-pin PDIP
Supply Voltage Range: 2.5V to 6V
I2C Bus Frequency: 100kHz
Comparar com PCF8574P →
Texas Instruments
Package: 16-DIP (0.300 inch, 7.62 mm)
Device Type: 8-bit I/O expander
Interface: I2C
Comparar com PCF8574P →

PCF8574P,112

✅ Drop-In
📦 DIP-16
Electrical ratings are 0% different at 8 ports, 2.5 V to 6 V, and 100 kHz; the ,112 ordering suffix identifies the exact NXP catalog form.

📋 Alternativa de referência (fora do catálogo)

PCF8574N

✅ Drop-In
Texas Instruments
📦 DIP-16
8-bit I2C I/O expander · 2.5V to 6V · 100kHz · 8 · I2C two-line bidirectional bus · Interrupt output · 16-pin PDIP · Through-hole

Consulte o preço

Ver ficha técnica →

PCF8574PN

✅ Drop-In
📦 DIP-16
Core specifications are 0% different at 8 ports, 2.5 V to 6 V, and 100 kHz; confirm the exact suffix and address mapping before substitution.

📋 Alternativa de referência (fora do catálogo)

PCF8574NG4

✅ Drop-In
Texas Instruments
📦 DIP-16
8-bit I/O expander · I2C · 100 kHz · 2.5 V to 6 V · 8 lines · 8-bit quasi-bidirectional · Two-line bidirectional · 16-DIP (0.300 inch, 7.62 mm)

Consulte o preço

Ver ficha técnica →

PCF8574N

✅ Drop-In
Texas Instruments
📦 DIP-16
8-bit I2C I/O expander · 2.5V to 6V · 100kHz · 8 · I2C two-line bidirectional bus · Interrupt output · 16-pin PDIP · Through-hole

Consulte o preço

Ver ficha técnica →

PCF8574P Especificações

Device Type Remote 8-bit I2C I/O expander with interrupt
Number of I/O Ports 8 ports
Port Width 8 bits
Supply Voltage Range 2.5 V to 6 V
I2C Bus Frequency 100 kHz
Bus Interface Two-wire bidirectional I2C-bus
Serial Clock Pin SCL
Serial Data Pin SDA
Hardware Address Inputs 3 inputs
Interrupt Output 1 open-drain interrupt output
Port Type 8 quasi-bidirectional I/O ports
Encapsulamento 16-pin DIP
Tipo de montagem Through-hole
I2C Pull-Up Requirement External pull-up resistors required

Configuração de pinos do PCF8574P

DIP-16 Package Pinout Diagram DIP-16 16-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 DIP-16
Pino 1 A0 — Hardware address input A0
Pino 2 A1 — Hardware address input A1
Pino 3 A2 — Hardware address input A2
Pino 4 P0 — Quasi-bidirectional I/O port P0
Pino 5 P1 — Quasi-bidirectional I/O port P1
Pino 6 P2 — Quasi-bidirectional I/O port P2
Pino 7 P3 — Quasi-bidirectional I/O port P3
Pino 8 GND — Ground connection
Pino 9 P4 — Quasi-bidirectional I/O port P4
Pino 10 P5 — Quasi-bidirectional I/O port P5
Pino 11 P6 — Quasi-bidirectional I/O port P6
Pino 12 P7 — Quasi-bidirectional I/O port P7
Pino 13 INT — Open-drain interrupt output
Pino 14 SDA — Serial data input and output
Pino 15 SCL — Serial clock input
Pino 16 VDD — Positive supply voltage

Aplicações típicas

PCF8574P é adequado para 6 aplicaçãos: Arduino GPIO Expansion, ESP32 IoT Control Interface, LED and Human-Interface Control, Industrial Relay and Discrete Control, Automation Data Acquisition, Embedded Access and Security Panels.

🔧

Arduino GPIO Expansion

The PCF8574P adds eight quasi-bidirectional ports to an Arduino-compatible controller without consuming direct digital pins for every accessory. It communicates through SDA and SCL at up to 100 kHz, while three hardware address inputs permit additional expanders on the same bus. The 16-pin DIP package is useful for through-hole prototype boards and industrially wired control panels. Use suitable I2C pull-ups and confirm the board's logic voltage. The ports are better suited to indicator LEDs, push buttons, and relay-control inputs than to high-speed or high-current outputs.

🧩

ESP32 IoT Control Interface

The PCF8574P is useful in ESP32-based IoT devices when the wireless module needs additional lines for status indicators, sensors, or control inputs. Its 100 kHz I2C-bus remains compatible with common embedded I2C implementations, and the 2.5 V to 6 V operating range supports typical 3.3 V and 5 V systems when the I2C pull-ups are correctly referenced. Three address inputs simplify multi-expander addressing. Keep the wiring short, place pull-ups at the bus master, and avoid relying on the quasi-bidirectional ports for signals that require fast edge rates.

💡

LED and Human-Interface Control

The PCF8574P can consolidate LED indicators, push buttons, and selector inputs in a human-interface panel. Eight quasi-bidirectional ports provide enough parallel lines for a compact keypad or mixed indicator and switch board, while the interrupt output allows the host controller to react when an input changes. The I2C transfer rate of 100 kHz is adequate for ordinary panel updates. Verify each port's source and sink-current limits, use current-limiting resistors for LEDs, and account for the port pull-up behavior when designing debounce and input-conditioning circuits.

🏭

Industrial Relay and Discrete Control

The PCF8574P can provide a compact low-speed control interface for relay drivers, discrete sensors, and alarm lines in industrial equipment. Its eight ports reduce the number of direct host-controller pins needed, and the 100 kHz I2C-bus is suitable for command and status traffic rather than real-time sampling. The open-drain interrupt output supports event notification from input ports. Separate the low-current logic side from inductive or high-energy loads, use appropriate driver transistors, and add protection networks for long wiring runs and electrically harsh environments.

⚡

Automation Data Acquisition

The PCF8574P can collect several low-speed digital signals in automation and data-acquisition equipment while leaving the main controller available for higher-level tasks. Eight ports can represent switch states, direction commands, interlocks, or equipment-enable signals, and three address inputs allow expansion when another bank is required. The interrupt output reduces unnecessary polling in master/slave arrangements. Use the 100 kHz bus rate only for suitably slow signals, account for contact bounce, and add filtering or isolation where field wiring introduces transients and ground-potential differences.

📱

Embedded Access and Security Panels

The PCF8574P is suitable for low-speed access-control panels, alarm interfaces, and keypad-based security equipment where a small controller needs more discrete lines. The expander can supervise door, tamper, or status inputs and operate indicator or latch-control outputs over I2C. The interrupt output provides a practical way to flag input changes without continuous polling. Security designs should not treat a quasi-bidirectional port as a high-integrity isolated input; use appropriate isolation, debounce, surge protection, and fail-safe power architecture based on the installation hazard and required safety level.

What is the PCF8574P and what does it do?
The PCF8574P is an 8-bit I2C I/O expander that adds eight quasi-bidirectional GPIO ports to a host microcontroller. It uses the two-wire bidirectional I2C-bus for communication and includes a 100 kHz bus interface. According to the NXP product information, the device also provides three hardware address inputs and an interrupt output, allowing multiple expanders and event-driven input monitoring on one bus.
What is the PCF8574P operating voltage range?
The PCF8574P operates from 2.5 V through 6 V. The NXP product page identifies the device as an 8-bit remote I/O expander with interrupt for the I2C-bus and states that the PCF8574 family works between 2.5 V and 6 V. Keep the I2C pull-up voltages and connected peripheral supplies within this range, and confirm voltage compatibility when the host operates at 5 V.
How many I2C devices can share the PCF8574P bus?
The PCF8574P provides three hardware address inputs, allowing multiple instances to coexist on one I2C-bus. The NXP product page identifies three hardware address inputs on the device. The exact address assigned to each expander depends on how A0, A1, and A2 are connected, so firmware and PCB address strapping must agree. Check the manufacturer address table before assigning fixed addresses in code.
What is the PCF8574P I2C address?
The PCF8574P address is selected by the A0, A1, and A2 hardware inputs. The NXP product page confirms three address-selection inputs, and the manufacturer address table maps their levels to the device address. Because the address can vary with the strapping configuration, read that table directly when creating firmware constants. Several expander modules use the common 0x20 configuration when all three address inputs are tied low.
Where can I download the PCF8574P datasheet PDF?
The PCF8574P datasheet PDF is available from the NXP product page and the linked manufacturer documentation. The NXP PCF8574P product information identifies the device as a remote 8-bit I/O expander for the I2C-bus with interrupt and provides the associated data sheet. Use the pin-description and address tables in the manufacturer datasheet when assigning PCB nets and writing device-level drivers.
Where is the PCF8574P pinout located?
The PCF8574P pinout is documented in the manufacturer datasheet and represented on this page by the 16-pin DIP diagram. Pins include A0, A1, A2, P0 through P7, GND, INT, SDA, SCL, and VDD. Use the pin-description table in the NXP datasheet when assigning tracks, particularly to distinguish the open-drain INT output from the quasi-bidirectional P0-P7 ports.
Can PCF8574P replace a missing Arduino GPIO pin?
Yes, the PCF8574P can provide eight additional I/O lines for an Arduino-compatible design when voltage, timing, and current requirements are satisfied. The PCF8574P supports 2.5 V to 6 V operation and a 100 kHz I2C interface, making it suitable for a 5 V Arduino bus. Because the ports are quasi-bidirectional, they are better suited to LEDs, keys, and moderate loads than to high-current or high-speed outputs.
Can the PCF8574P be used with an ESP32?
The PCF8574P can be used with an ESP32 as an I2C GPIO expander, provided both devices share a compatible logic voltage and the ESP32 supports 100 kHz I2C operation. According to the NXP product information, the PCF8574P supports a 100 kHz I2C-bus and three hardware address inputs. Add suitable SDA and SCL pull-up resistors and confirm the ESP32 board's 3.3 V or 5 V pin tolerance.
What is the difference between PCF8574P and a PCF8574A?
The PCF8574P and PCF8574A share the 8-bit I/O-expander function, but their I2C slave-address assignments are not automatically interchangeable. A software driver written for one variant should not be assumed to work with the other without checking the manufacturer address table. For a drop-in PCB replacement, confirm both the physical pinout and the exact address mapping in firmware before choosing a PCF8574A.
What are the key specifications of PCF8574P that engineers should know?
The key PCF8574P specifications are eight quasi-bidirectional I/O ports, a 2.5 V to 6 V supply range, a 100 kHz I2C-bus interface, three hardware address inputs, and an interrupt output in a 16-pin DIP package. The NXP product page confirms the port count, voltage range, bus rate, address inputs, and interrupt function. These parameters determine bus compatibility, expansion capacity, address planning, and PCB footprint selection.
When should I choose PCF8574P over a TCA9554?
Choose the PCF8574P when your design specifically requires the PCF8574 address arrangement, an open-drain interrupt output, and a 16-pin DIP footprint. According to the NXP product information, it provides eight quasi-bidirectional ports, three address inputs, and a 100 kHz I2C-bus. A TCA9554 may offer different input, output, and address behavior, so compare its logic characteristics and firmware requirements rather than treating package similarity as sufficient.
Is PCF8574P suitable for driving LEDs and reading switches?
The PCF8574P is suitable for typical LED-indicator and switch-input circuits, with the electrical limits checked for each port. Its eight quasi-bidirectional ports can sink or source limited current, while the internal pull-up behavior supports switch-to-ground inputs. The manufacturer identifies the device as an 8-bit remote I/O expander. Add a suitable current-limiting resistor for each LED and verify the required source and sink currents in the datasheet.
What is the best drop-in replacement for PCF8574P?
The closest drop-in replacement is a non-A PCF8574-family device in the same 16-pin DIP package with the same 2.5 V to 6 V supply range, 100 kHz I2C interface, eight ports, three address inputs, and interrupt output. The NXP product page confirms these defining characteristics. Verify the exact ordering suffix, pin orientation, and slave-address table; PCF8574A variants require special attention because their address mapping differs.
Where can I buy PCF8574P and check its current lead time?
Use the Request a Quote form on this page to ask for PCF8574P availability, current lead time, order quantity, and packaging requirements. The NXP product page identifies the device as a remote 8-bit I/O expander for the I2C-bus with interrupt, and distributor catalog pages confirm active sourcing channels for the device. A quotation request is the appropriate way to confirm current commercial terms for the exact ordering code.
How should pull-up resistors be placed for the PCF8574P I2C bus?
Place one pull-up resistor from SDA to the bus supply and one from SCL to the bus supply, keeping both devices electrically compatible with the 2.5 V to 6 V operating range. The I2C interface uses open-drain signaling, so pull-ups are required for valid high levels. Use the manufacturer interface guidance to select resistance and placement that balance rise time, bus capacitance, and sink-current capability.

Dados de referência de engenharia para PCF8574P — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the NXP PCF8574P when the design requires eight quasi-bidirectional ports, a 2.5 V to 6 V supply, 100 kHz I2C communication, three hardware address inputs, an interrupt output, and a 16-pin DIP footprint. It is a practical fit for through-hole Arduino, ESP32, and embedded control boards where adding a modest amount of GPIO is simpler than changing the host microcontroller. The PCF8574P,112 is the closest ordering option when a full NXP catalog code is needed, while other non-A PCF8574 DIP variants may simplify procurement. The Texas Instruments PCF8574N can be considered when supply-chain standardization makes a second manufacturer's catalog preferable, but its lifecycle and ordering status should be confirmed before schematic release. Do not select a PCF8574A solely by package similarity: verify its slave-address mapping and update firmware accordingly. In every case, validate port current, I2C pull-ups, logic voltage, and interrupt handling.

Comparação com alternativas

Parâmetro Este produto PCF8574P,112 PCF8574N PCF8574PN PCF8574NG4 PCF8574N
Package DIP-16 DIP-16 DIP-16 DIP-16 DIP-16 DIP-16
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors NXP Semiconductors Texas Instruments
I/O Port Count 8 8 8 8 8 8
Supply Voltage Range 2.5 V to 6 V 2.5 V to 6 V 2.5 V to 6 V 2.5 V to 6 V 2.5 V to 6 V 2.5 V to 6 V
I2C Bus Frequency 100 kHz 100 kHz 100 kHz 100 kHz 100 kHz 100 kHz
Hardware Address Inputs 3 3 3 3 3 3
Interrupt Output Yes Yes Yes Yes Yes Yes
Port Architecture Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional Quasi-bidirectional
Interrupt Output Type Open-drain Open-drain Open-drain Open-drain Open-drain Open-drain
Supply Pin Count 1 1 1 1 1 1

Principais diferenciais

  • Provides interrupt-supported input monitoring (vs PCF8574P,112)
  • Offers three address inputs for multi-expander expansion (vs PCF8574N)
  • Supports the same core interface envelope across manufacturers (vs PCF8574N)

Notas de projeto

Place the PCF8574P close to the devices connected to P0-P7, and keep the eight port traces away from high-current switching nodes to minimize coupling. Route SDA and SCL away from relay-coil wiring and other sources of high di/dt transients. For long external leads, place the ESD protection device near the connector and the expander near the logic ground reference so surge current does not flow through sensitive board traces.

Use pull-up resistors on both SDA and SCL, referenced to the same compatible logic voltage as the bus. Select resistance using the bus capacitance, the host controller's sink-current limit, and the required rise time rather than applying one value universally. Verify that every connected device tolerates the selected pull-up voltage. The PCF8574P operates from 2.5 V to 6 V, but the host and peripheral devices must share compatible logic levels.

Do not assume the quasi-bidirectional ports behave like ordinary push-pull GPIO. Their internal pull-ups are relevant when a port is read as an input, and an external driver may be required for reliable low-level input states. A high-impedance external signal can therefore behave unexpectedly. For an input port, actively drive the line high or low within the allowed voltage and current limits, and consult the datasheet for the required output-drive arrangement.

Confirm the slave-address table for every selected family member before finalizing firmware. PCF8574 and PCF8574A naming can suggest interchangeability even though their address mappings differ. Record the A0, A1, and A2 strapping in the schematic and test documentation. Also verify interrupt polarity and clearing behavior in software; INT is an open-drain output and normally requires an external pull-up.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

No definitive RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were identified for the exact ordering code.

Dados verificados em: 2026-11-14 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

pcf8574p datasheet pcf8574p arduino pcf8574p price pcf8574p address pcf8574p datasheet pdf pcf8574p i2c address pcf8574p pdf pcf8574 esp32 PCF8574P pinout PCF8574P replacement PCF8574P equivalent PCF8574P vs PCF8574A NXP PCF8574P

Componentes & termos relacionados

NXP Semiconductors PCF8574P PCF8574P,112 PCF8574N PCF8574PN PCF8574NG4 Texas Instruments I2C-bus SCL SDA I/O expander interface IC peripheral expansion device quasi-bidirectional port 8-bit GPIO 100 kHz I2C 2.5 V to 6 V open-drain interrupt DIP-16 through-hole package hardware address input Arduino ESP32 industrial automation human-machine interface
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ