PIC16C72-10/SS - 8-Bit CMOS MCU, 3.5KB EPROM, 22 I/O, SSOP-28
N.º da peça: PIC16C72-10/SS ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $9.85 | $9,85 |
| 10 | $8.92 | $89,20 |
| 100 | $7.74 | $774,00 |
| 500 | $6.55 | $3.275,00 |
| 1.000 | $5.62 | $5.620,00 |
PIC16C72-10/SS Visão geral
What is a PIC16C72 microcontroller? The PIC16C72 belongs to Microchip's PIC16CXX mid-range architecture family, which sits within the broader PIC microcontroller hierarchy (PIC10/12/14/16/18/24/32) and the 8-bit MCU category. Mid-range PICs implement a RISC instruction set (35 single-word instructions), Harvard memory architecture (separate program and data buses), and integrated peripherals such as A/D converters, timers, and synchronous/asynchronous serial ports - making them suitable for embedded control applications where deterministic instruction timing and low BOM cost are priorities. The "C" in PIC16C72 indicates the EPROM program memory technology (as opposed to "F" for Flash or "LF" for low-voltage Flash).
Key features include three I/O ports (PORTA, PORTB, PORTC), two 8-bit timer/counters (Timer0, Timer2) plus one 16-bit timer (Timer1), a Synchronous Serial Port (SSP) supporting SPI and I2C, 22 general-purpose digital I/O lines with individual direction control, an analog comparator, and a 5-channel 8-bit A/D converter with selectable reference. The Harvard bus architecture and 14-bit instruction word allow most instructions to execute in a single 200 ns instruction cycle at 20 MHz, or 400 ns at 10 MHz (the -10 grade), supporting predictable interrupt latency in real-time control loops.
Typical applications include motor control (low-side PWM driving via Timer2), sensor interfacing with on-chip A/D conversion, simple SMPS control loops, automotive body electronics in pre-CAN architectures, white goods user-interface controllers, and industrial instrumentation. The 22 I/O pins provide ample headroom for keypad scanning, LED matrix driving, and LCD segment control. The integrated A/D converter eliminates the need for an external ADC in cost-sensitive designs.
When designing with the PIC16C72-10/SS, note that this is a One-Time-Programmable EPROM part - firmware is committed during production programming and cannot be field-updated. For prototyping or field-updateable designs, prefer the PIC16F72 (Flash) drop-in. Always place a 0.1 uF decoupling capacitor within 5 mm of the VDD pin and connect the MCLR pin through a 10 kohm pull-up to VDD for reliable reset behavior.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas drop-in para PIC16C72-10/SS — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16C72-10/SS (mesmo formato e footprint) — diferindo em Package, Core Architecture, Operating Temperature, ADC, Timers.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F72-I/SS
✅ Drop-In✓ Em estoque
$2.19 / unidade
Ver ficha técnica →PIC16C72-10I/SS
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16C72-10E/SS
✅ Drop-In✓ Em estoque
$3.3 / unidade
Ver ficha técnica →PIC16C72-10/SP
✅ Drop-In✓ Em estoque
$4.42 / unidade
Ver ficha técnica →PIC16F716-I/SO
✅ Drop-In✓ Em estoque
$1.13 / unidade
Ver ficha técnica →PIC16C72-10/SS Classificações máximas e características elétricas
| Core Architecture | PIC16CXX mid-range 8-bit RISC |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 3.5 KB |
| RAM | 128 bytes |
| Data EEPROM | Not present |
| Frequência máxima de clock | 10 MHz |
| Instruction Cycle Time | 400 ns at 10 MHz |
| Supply Voltage (VDD) | 2.0 V to 6.0 V |
| I/O Pins | 22 |
| A/D Converter | 5-channel, 8-bit |
| Timers | Timer0 (8-bit), Timer1 (16-bit), Timer2 (8-bit) |
| Serial Interfaces | SSP (SPI / I2C) |
| Encapsulamento | SSOP-28 |
| Temperatura de operação | 0 C to +70 C (Commercial) |
| Tipo de montagem | Surface Mount |
| Pin/Package Code | SS / GULL WING, 28 terminals |
| Tube Packaging | Yes |
| Status RoHS | Compliant (lead-free SS suffix) |
Configuração de pinos do PIC16C72-10/SS
| Pino 1 | MCLR/VPP — Master Clear (reset) input / programming voltage input |
| Pino 2 | RA0/AN0 — PORTA bit 0 / Analog input channel 0 |
| Pino 3 | RA1/AN1 — PORTA bit 1 / Analog input channel 1 |
| Pino 4 | RA2/AN2 — PORTA bit 2 / Analog input channel 2 |
| Pino 5 | RA3/AN3/VREF — PORTA bit 3 / Analog input 3 / ADC reference |
| Pino 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pino 7 | RA5/SS/AN4 — PORTA bit 5 / SPI Slave Select / Analog input 4 |
| Pino 8 | VSS — Ground |
| Pino 9 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| Pino 10 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| Pino 11 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| Pino 12 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / CCP2 output |
| Pino 13 | RC2/CCP1 — PORTC bit 2 / CCP1 PWM output |
| Pino 14 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pino 15 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pino 16 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pino 17 | RC6 — PORTC bit 6 |
| Pino 18 | RC7 — PORTC bit 7 |
| Pino 19 | VSS — Ground (digital) |
| Pino 20 | VDD — Positive supply voltage |
| Pino 21 | RB0/INT — PORTB bit 0 / External interrupt input |
| Pino 22 | RB1 — PORTB bit 1 |
| Pino 23 | RB2 — PORTB bit 2 |
| Pino 24 | RB3 — PORTB bit 3 |
| Pino 25 | RB4 — PORTB bit 4 (interrupt-on-change) |
| Pino 26 | RB5 — PORTB bit 5 (interrupt-on-change) |
| Pino 27 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pino 28 | RB7/PGD — PORTB bit 7 / ICSP data |
Aplicações típicas
PIC16C72-10/SS é adequado para 6 aplicaçãos: Industrial Sensor Interface Module, Consumer Appliance User Interface, Low-Side DC Motor Control, Battery-Powered Remote Control, Automotive Body Electronics (Pre-CAN), Simple Switch-Mode Power Supply (SMPS) Controller.
Industrial Sensor Interface Module
The PIC16C72-10/SS fits industrial 4-20 mA sensor conditioning boards because its 5-channel 8-bit A/D converter maps directly onto thermocouple, pressure, and flow sensor inputs through a multi-channel analog mux. The 22 I/O pins drive isolated relay outputs, status LEDs, and an SPI-connected LCD controller, while the 128-byte RAM is sufficient for averaging filters and linearization tables. At 10 MHz the 400 ns instruction cycle allows ADC sampling at 5 kHz with simple digital filtering. The part is recommended for cost-sensitive, non-field-upgradeable sensor hubs running stable production firmware.
Recomendado
Consumer Appliance User Interface
The PIC16C72-10/SS is well matched to washing machine, dishwasher, and microwave oven keypads and display controllers where 22 I/O pins are required for a 4x4 matrix keypad plus 7-segment LED drivers. The integrated SSP peripheral supports I2C communication with a separate temperature sensor IC, while Timer2 generates the multiplex refresh for the LED digits. The 2.0-6.0 V supply range tolerates unregulated 5 V rails common in white goods. With its 3.5 KB OTP EPROM, production firmware is committed at the manufacturing line - ideal for high-volume appliance designs with locked bill-of-materials.
Recomendado
Low-Side DC Motor Control
The PIC16C72-10/SS drives small DC motors, solenoids, and stepper motor coils in 12 V systems by using Timer2 PWM output on PORTB and high-current MOSFET gate drivers on PORTC. With a 10 MHz clock, PWM resolution reaches 10 bits at modest frequencies or 8 bits at 39 kHz - suitable for brushed DC motor speed control and bipolar stepper microstepping. The A/D converter samples a current-sense resistor for closed-loop current limiting, while the analog comparator detects overcurrent faults. The OTP EPROM makes this part a good fit for high-volume motor controllers with locked production firmware.
Recomendado
Battery-Powered Remote Control
The PIC16C72-10/SS fits handheld remote controls and small battery-operated devices thanks to its 2.0 V minimum VDD allowing operation from two AA cells down to 2.4 V. The mid-range core supports the SLEEP instruction with wake-on-change interrupts on PORTB, drawing less than 1 uA standby current. The integrated SSP peripheral drives an infrared LED for IR remote transmission using carrier generation via Timer0. With 22 I/O lines, the controller supports 16-button matrix keypads plus status LEDs and LCD segments, all in a compact SSOP-28 footprint.
Recomendado
Automotive Body Electronics (Pre-CAN)
For pre-CAN automotive body modules such as seat controllers, mirror adjusters, and lighting nodes, the PIC16C72-10/SS offers 22 I/O lines, a 5-channel A/D for current sensing, and an SSP for LIN or SPI communication to a master ECU. Operating from the vehicle's 12 V rail regulated to 5 V, the part's 2.0-6.0 V VDD range tolerates cranking transients when paired with appropriate TVS and bulk capacitance. While the part is commercial grade, the PIC16C72-10I/SS industrial variant extends temperature coverage to -40 C to +85 C for under-dash applications.
Recomendado
Simple Switch-Mode Power Supply (SMPS) Controller
The PIC16C72-10/SS serves as a low-cost digital SMPS controller for sub-50 W non-isolated DC/DC converters such as buck regulators for distributed POL rails. Timer2 generates the PWM drive, the A/D converter samples output voltage and current for closed-loop regulation, and the analog comparator provides hardware overcurrent protection within one instruction cycle. The 10 MHz maximum clock supports switching frequencies up to 100 kHz with proportional-integral firmware loops. The 3.5 KB OTP EPROM stores the fixed regulation profile for high-volume production.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16C72-10/SS — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F72-I/SS | PIC16C72-10I/SS | PIC16C72-10E/SS | PIC16C72-10/SP | PIC16F716-I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SSOP-28 | SSOP-28 - same | SSOP-28 - same | SSOP-28 - same | PDIP-28 - through-hole | SSOP-28 - same |
| Program Memory | 3.5 KB OTP EPROM | 3.5 KB Flash | 3.5 KB OTP EPROM | 3.5 KB OTP EPROM | 3.5 KB OTP EPROM | 3.5 KB Flash |
| Maximum Clock | 10 MHz | 20 MHz | 10 MHz | 10 MHz | 10 MHz | 20 MHz |
| I/O Pins | 22 | 22 | 22 | 22 | 22 | 13 |
| A/D Converter | 5 ch, 8-bit | 5 ch, 8-bit | 5 ch, 8-bit | 5 ch, 8-bit | 5 ch, 8-bit | 4 ch, 8-bit |
| Operating Temperature | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) |
| Lifecycle Status | Obsolete | Active | Obsolete | Obsolete | Obsolete | Active |
| Unit Price (1 qty, USD) | $9.85 | $4.30 | $10.50 | $12.00 | $9.45 | $2.95 |
Principais diferenciais
- Active production alternative with same footprint (vs PIC16F72-I/SS)
- Industrial temperature upgrade in identical package (vs PIC16C72-10I/SS)
- Extended temperature grade for harsh environments (vs PIC16C72-10E/SS)
Notas de projeto
Place a 0.1 uF ceramic decoupling capacitor within 5 mm of the VDD pin (pin 20) and connect both VSS pins (pins 8 and 19) directly to a low-impedance ground plane. For designs operating above 20 MHz internal bus speed or with high-current switching peripherals, add a 10 uF bulk tantalum or ceramic capacitor near the MCU. Brown-out detection should be enabled (BODEN configuration bit set) for any battery-powered or loosely-regulated supply; this prevents code execution corruption below the 2.0 V VDD minimum.
Keep the oscillator traces (OSC1/OSC2, pins 9-10) short - less than 10 mm - and guard them with a ground pour on both sides of the PCB. Use a four-pin crystal plus two load capacitors matched to the crystal manufacturer's CL specification (typically 15-33 pF for 10 MHz). If using an external CMOS clock, drive OSC1 with a series 10 ohm resistor close to the MCU pin to reduce overshoot. For SSOP-28, allocate at least 0.5 mm clearance between analog (PORTA) traces and switching signals like the CCP1 PWM output on RC2 to minimize ADC crosstalk.
The PIC16C72 uses One-Time-Programmable EPROM - once programmed, the firmware CANNOT be erased or rewritten. This makes the part unsuitable for prototypes requiring iterative firmware updates; choose the PIC16F72 (Flash, ICSP) for development and switch to the PIC16C72 for cost-optimized production only. Also note that configuring the MCLR pin as a digital input (instead of the default reset function) disables the device's ability to recover from code runaway - leave MCLR as a reset pin and drive it through a 10 kohm pull-up to VDD.
Estimated: at 10 MHz clock the PIC16C72 generates edge rates of approximately 4 ns on output pins. Route high-speed output traces (CCP1 PWM, SPI SCK/SDO) over a continuous ground plane and keep trace lengths under 25 mm to avoid ringing. Place the analog VREF decoupling (RA3/VREF) as a 0.1 uF + 10 uF combination within 3 mm of the pin to keep ADC reference noise below 1 LSB at 8-bit resolution. Separate the analog ground island under PORTA from the digital ground island with a single-point connection at the MCU VSS pin.
Informações de conformidade
SS suffix indicates lead-free SSOP package per Microchip packaging conventions. RoHS and REACH compliance verified from Microchip product declarations. Part is not AEC-Q100 qualified; for automotive applications requiring AEC-Q100, choose PIC16F72-I/SS or PIC16C72-10I/SS industrial grade. Halogen-free status not explicitly stated in retrieved data.
