PIC16C77-10E/PT - 8-Bit 10MHz OTP MCU 14KB Flash 44-TQFP | Microchip
N.º da peça: PIC16C77-10E/PT ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $16.34 | $16,34 |
| 10 | $14.71 | $147,10 |
| 100 | $13.07 | $1.307,00 |
| 500 | $11.44 | $5.720,00 |
| 1.000 | $9.8 | $9.800,00 |
PIC16C77-10E/PT Visão geral
An MCU (microcontroller unit) is a single-chip computer containing a CPU core, non-volatile program memory, working RAM, peripherals, and I/O - essentially a complete compute subsystem on one IC. The 8-bit PIC16C family targets low-cost, deterministic, low-power embedded applications where simple register-level programming, predictable interrupt latency, and small footprint outweigh the throughput advantages of 16/32-bit cores. The PIC16C77 is the upper-memory sibling of the PIC16C76 within the mid-range PIC16C6X/7X family, adding 8K words of code space and an extended instruction set.
Key features of the PIC16C77-10E/PT include a wide operating voltage range of 2.5V to 6.0V, 25 mA source/sink current per I/O to directly drive LEDs or small relays, low-power consumption (typical <2 mA active at 5V/4MHz), and three temperature grades. The "-10E" suffix indicates 10MHz maximum frequency and the Extended (-40C to +125C) temperature range. The 44-TQFP (PT) package variant also offers 40-pin PDIP (P) and 44-pin PLCC (L) options for through-hole and socketed designs.
Architecturally, the PIC16C77 uses a Harvard RISC core with separate program and data buses, allowing simultaneous instruction fetch and data access. The 14-bit wide instruction word supports single-word single-cycle instructions with 200 ns minimum cycle time at 10MHz. The on-chip peripherals are mapped into a 368-byte register file and 8-level hardware stack, and an integrated power-on reset / brown-out detector / watchdog timer trio provides unsupervised operation. The synchronous serial port can be configured as SPI master/slave or I2C, while the AUSART delivers asynchronous or synchronous serial communication.
Typical applications include industrial automation controllers, sensor signal conditioning with on-chip ADC, motor and lighting control with PWM, HVAC user-interface panels, automotive body and accessory ECUs, and consumer appliance controllers. Its 33 I/O lines comfortably support mid-sized user interfaces with keypads, displays, and indicator LEDs.
When designing with the PIC16C77-10E/PT, the OTP memory constraint is critical: program code must be fully verified before production programming because OTP cannot be erased. For prototype or field-updatable designs, use the flash-based PIC16F77 drop-in successor. Always include decoupling capacitors within 10 mm of the VDD/VSS pins, and respect the 6.0V absolute-maximum supply.
This page synthesizes distributor pricing, drop-in alternatives, application notes, and design considerations not consolidated in the manufacturer datasheet.
Alternativas drop-in para PIC16C77-10E/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16C77-10E/PT (mesmo formato e footprint) — diferindo em Timers, Core Architecture, Serial Interfaces, Package, Program Memory Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16C77-10/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.7 / unidade
Ver ficha técnica →PIC16C77-04I/PT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16F77-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.4 / unidade
Ver ficha técnica →PIC16F877A-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$4.95 / unidade
Ver ficha técnica →PIC16C77-20E/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$8.75 / unidade
Ver ficha técnica →PIC16C77-10E/PT Classificações máximas e características elétricas
| Core Architecture | PIC 8-bit Harvard RISC |
| Series | PIC® 16C |
| Program Memory Type | OTP (One-Time Programmable) |
| Program Memory Size | 14 KB (8K x 14) |
| RAM Size | 368 B |
| EEPROM Data Memory | None |
| Maximum CPU Frequency | 10 MHz |
| Instruction Cycle Time | 200 ns |
| Operating Voltage Range | 2.5 V to 6.0 V |
| I/O Pins | 33 |
| ADC | 8 channels, 8-bit |
| Timers | 2 x 8-bit, 1 x 16-bit (CCP) |
| Communication Interfaces | AUSART, SPI, I2C (SSP) |
| I/O Sink/Source Current | 25 mA / 25 mA |
| Temperatura de operação | -40 C to +125 C (Extended, "E" suffix) |
| Encapsulamento | 44-TQFP (10x10 mm), "PT" suffix |
| Tipo de montagem | Surface Mount |
| Packaging | Tube |
Configuração de pinos do PIC16C77-10E/PT
| Pino 1 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Pino 2 | RA1/AN1 — PORTA bit 1 / analog input 1 |
| Pino 3 | RA2/AN2 — PORTA bit 2 / analog input 2 |
| Pino 4 | RA3/AN3/VREF — PORTA bit 3 / analog input 3 / VREF+ |
| Pino 5 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pino 6 | RA5/AN4/SS — PORTA bit 5 / analog input 4 / SPI slave select |
| Pino 7 | RE0/RD — PORTE bit 0 / parallel slave port read |
| Pino 8 | RE1/WR — PORTE bit 1 / parallel slave port write |
| Pino 9 | RE2/CS — PORTE bit 2 / parallel slave port chip select |
| Pino 10 | VDD — Positive digital supply (2.5-6.0 V) |
| Pino 11 | VSS — Digital ground |
| Pino 12 | OSC1/CLKIN — Crystal oscillator input / external clock in |
| Pino 13 | OSC2/CLKOUT — Crystal oscillator output / clock out |
| Pino 14 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator out / Timer1 clock in |
| Pino 15 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator in / CCP2 |
| Pino 16 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Pino 17 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pino 18 | RD0/PSP0 — PORTD bit 0 / parallel slave port bit 0 |
| Pino 19 | RD1/PSP1 — PORTD bit 1 / parallel slave port bit 1 |
| Pino 20 | RD2/PSP2 — PORTD bit 2 / parallel slave port bit 2 |
| Pino 21 | RD3/PSP3 — PORTD bit 3 / parallel slave port bit 3 |
| Pino 22 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pino 23 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pino 24 | RC6/TX/CK — PORTC bit 6 / AUSART TX / clock |
| Pino 25 | RC7/RX/DT — PORTC bit 7 / AUSART RX / data |
| Pino 26 | RD4/PSP4 — PORTD bit 4 / parallel slave port bit 4 |
| Pino 27 | RD5/PSP5 — PORTD bit 5 / parallel slave port bit 5 |
| Pino 28 | RD6/PSP6 — PORTD bit 6 / parallel slave port bit 6 |
| Pino 29 | RD7/PSP7 — PORTD bit 7 / parallel slave port bit 7 |
| Pino 30 | AVSS — Analog ground |
| Pino 31 | AVDD — Analog positive supply |
| Pino 32 | VSS — Digital ground |
| Pino 33 | VDD — Positive digital supply (2.5-6.0 V) |
| Pino 34 | RB0/INT — PORTB bit 0 / external interrupt |
| Pino 35 | RB1 — PORTB bit 1 |
| Pino 36 | RB2 — PORTB bit 2 |
| Pino 37 | RB3 — PORTB bit 3 |
| Pino 38 | RB4 — PORTB bit 4 |
| Pino 39 | RB5 — PORTB bit 5 |
| Pino 40 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pino 41 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pino 42 | RC0 — PORTC bit 0 (alternate location, dup) |
| Pino 43 | MCLR/VPP — Master clear reset (active low) / programming voltage |
| Pino 44 | VSS — Digital ground |
Aplicações típicas
PIC16C77-10E/PT é adequado para 6 aplicaçãos: Industrial Automation Controllers, Automotive Body and Accessory ECUs, HVAC Control Panels, Sensor Signal Conditioning and Data Acquisition, Motor Control (PWM and Stepper Drivers), Consumer Appliance Controllers.
Industrial Automation Controllers
The PIC16C77-10E/PT's 33 I/O lines, 8-channel 8-bit ADC, three timers, and 25 mA source/sink drive make it well suited to industrial PLCs, sensor-interface modules, and discrete control boards. Its 14 KB OTP program memory accommodates ladder-style logic and serial-protocol stacks, while the wide 2.5-6.0 V supply and -40C to +125C extended temperature range let it survive 24 V-conditioned industrial rails and factory-floor thermal stress. Place 100 nF decoupling caps within 10 mm of VDD/VSS, and use the AUSART for Modbus RTU over RS-485 transceivers.
Recomendado
Automotive Body and Accessory ECUs
Automotive body controllers, lighting modules, and accessory ECUs benefit from the PIC16C77-10E/PT's 25 mA I/O drive (enough to switch small relays and LED arrays directly), 8-channel ADC for battery-voltage and switch-state monitoring, and extended -40C to +125C operating range. The PWM-capable 16-bit CCP timer drives LED dimming and motor speed control without additional driver ICs, while the SSP supports SPI/I2C for sensor peripherals. For new automotive designs, prefer the AEC-Q100-qualified PIC16F877A-I/PT instead.
Recomendado
HVAC Control Panels
HVAC user-interface panels and thermostat controllers use the PIC16C77-10E/PT to scan keypads, drive LCD/LED displays, and read temperature/humidity sensors via the on-chip 8-channel 8-bit ADC. The 14 KB OTP memory holds UI state machines and PID control loops, while three timers handle PWM fan-speed outputs, scheduling, and debounce. The AUSART links the panel to a central HVAC controller for zone coordination, and the wide 2.5-6.0 V supply tolerance simplifies 5 V and 3.3 V mixed-rail designs.
Recomendado
Sensor Signal Conditioning and Data Acquisition
Multi-channel sensor-interface modules use the PIC16C77-10E/PT's 8-channel 8-bit ADC plus 33 I/O to read thermocouples, flow meters, pressure transducers, and switch contacts. The AUSART streams conditioned data to a host PLC or PC, while the SSP interfaces with SPI-based digital sensors. With 368 bytes of RAM and 14 KB of OTP program memory, the device holds calibration tables and linearization routines. Brown-out reset and watchdog timer provide unsupervised field operation.
Recomendado
Motor Control (PWM and Stepper Drivers)
Brushless DC, brushed DC, and small stepper-motor control loops fit within the PIC16C77-10E/PT's PIC16C core, leveraging the 16-bit CCP module for PWM generation and the 8-bit timers for commutation timing. The 25 mA I/O source/sink capability directly drives opto-isolated gate drivers, while the SSP synchronizes with encoder feedback over SPI. With 10 MHz CPU, the 200 ns instruction cycle supports 5-10 kHz commutation rates typical of small appliance and pump motors.
Recomendado
Consumer Appliance Controllers
Washing machines, dishwashers, microwave ovens, and small kitchen appliances integrate the PIC16C77-10E/PT for cycle control, user-interface handling, and safety monitoring. The wide 2.5-6.0 V supply accommodates rectified mains-derived rails, while the 8-channel ADC reads temperature, water level, and motor current sensors. OTP-based code locks in firmware against accidental field changes, and 33 I/O lines drive seven-segment displays, keypads, indicator LEDs, and TRIAC firing circuits through optocouplers.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16C77-10E/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16C77-10/PT | PIC16C77-04I/PT | PIC16F77-I/PT | PIC16F877A-I/PT | PIC16C77-20E/PT |
|---|---|---|---|---|---|---|
| Package | 44-TQFP (PT) | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same | 44-TQFP (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory Type | OTP (14 KB / 8K x 14) | OTP (14 KB) | OTP (14 KB) | Flash (14 KB) | Flash (14 KB) | OTP (14 KB) |
| Maximum CPU Frequency | 10 MHz | 10 MHz | 4 MHz | 10 MHz (20 MHz also offered) | 20 MHz | 20 MHz |
| Operating Temperature | -40 C to +125 C (Extended) | 0 C to +70 C (Commercial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) |
| RAM Size | 368 B | 368 B | 368 B | 368 B | 368 B | 368 B |
| ADC | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 8-bit | 8-ch, 10-bit | 8-ch, 8-bit |
| Communication Interfaces | AUSART, SPI, I2C (SSP) | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C | AUSART, SPI, I2C |
| Recommended for New Design | No (NRND) | No (NRND) | No (NRND) | Yes (recommended replacement) | Yes (active) | No (NRND) |
Principais diferenciais
- Recommended modern flash replacement available (vs PIC16F77-I/PT)
- Higher ADC resolution available in same package (vs PIC16F877A-I/PT)
- Faster CPU option in same package (vs PIC16C77-20E/PT)
- Extended temperature grade coverage (vs PIC16C77-10/PT)
Notas de projeto
Decouple each VDD/VSS pair with a 100 nF ceramic capacitor placed within 10 mm of the IC pins; add a bulk 10 uF electrolytic or tantalum at the board supply entry. The PIC16C77 has separate AVSS/AVDD analog supply pins; route AVSS to the analog ground plane and AVDD through an LC/RC filter to isolate ADC noise from digital switching. The wide 2.5-6.0 V supply range allows operation from a single Li-ion cell or 5 V rail without additional regulation, but never exceed 6.0 V (absolute maximum) - transients above this value destroy the part.
Place the crystal (or ceramic resonator) within 10 mm of OSC1/OSC2 and guard the traces with a grounded ring to reduce EMI pickup. Route MCLR/VPP with a short trace to a 10 kohm pull-up and a 100 nF cap to ground, forming a hardware-reset low-pass filter. For ICSP (in-circuit serial programming), bring PGC/PGD (RB6/RB7) and MCLR/VPP to an in-line 5-pin header accessible without removing the MCU from the board; keep these traces short and free of capacitive loading greater than 50 pF.
OTP memory cannot be erased - verify code with a flash equivalent (PIC16F77, PIC16F877A-I/PT) or a windowed PIC16C77 (with UV-erasable JW package) before programming production units. Brown-out reset must be enabled for field-deployed designs; otherwise a brief VDD sag can cause code corruption or runaway execution. The ADC maximum input must stay within AVSS to AVDD; do not apply negative voltages or voltages above AVDD. The 25 mA I/O drive is per-pin but subject to a package total dissipation limit - check the datasheet thermal characteristics when driving multiple high-current loads simultaneously.
Informações de conformidade
Lifecycle status is NRND (Not Recommended for New Designs). Microchip recommends PIC16F77 as the modern flash replacement. RoHS, REACH, lead-free, and halogen-free status are not explicitly stated in the verified web data and are marked unknown.
