PIC16F15356-E/SS - 8-bit 32MHz 28KB Flash MCU | Microchip
N.º da peça: PIC16F15356-E/SS ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.18 | $2,18 |
| 10 | $1.96 | $19,60 |
| 100 | $1.74 | $174,00 |
| 500 | $1.45 | $725,00 |
| 1.000 | $1.22 | $1.220,00 |
PIC16F15356-E/SS Visão geral
An 8-bit microcontroller (MCU) is a small computer-on-a-chip built around an 8-bit data path. Within the semiconductor taxonomy, an MCU sits under microcontroller -> embedded processor -> digital IC. PIC16 parts use a Harvard RISC architecture with a 14-bit instruction word optimized for deterministic, low-power control. The CIPs approach lets peripherals (CLC, CWG, NCO, PWM) operate without CPU intervention, lowering active power and freeing the core for application logic.
Key differentiating features include four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two 10-bit DACs, two 10-bit ADCs up to 43 channels, a Numerically Controlled Oscillator (NCO), four 10-bit PWMs, two analog comparators, and 2x EUSART plus 2x MSSP (SPI/I2C) serial interfaces. The XLP idle/doze currents enable battery lifetimes measured in years on coin cells.
The PIC16F15356-E/SS is pin-compatible with much of the PIC16F153xx family (e.g., PIC16F15355-E/SS with 14 KB Flash and PIC16F15354-E/SS with 7 KB Flash), enabling firmware migration across memory tiers without PCB rework. Memory is partitioned for bootloader-over-the-air updates and field firmware upgrades, a common requirement in connected sensor nodes.
Typical applications include IoT sensor nodes, battery-powered instrumentation, LED lighting controllers, low-cost motor control (small fans, solenoids), home appliance user-interface boards, and automotive body electronics (with the -VAO automotive grade variant). Designers choose this device when they need ample Flash for protocol stacks (BLE through external radio, LoRa, Modbus) plus rich analog peripherals for sensor fusion.
When designing with this part, keep in mind that SSOP-28 has limited thermal dissipation at high ambient temperatures. Place a 0.1 uF decoupling capacitor within 2 mm of VDD with a 10 uF bulk capacitor on the supply rail, and route MCLR through a 10 k pull-up. Programming/debug uses ICSP via the PGC/PGD pins, which should be reserved for test access.
This page synthesizes distributor pricing, drop-in same-package alternatives, design notes, and datasheet pinout data into a single engineering reference for the PIC16F15356-E/SS.
Alternativas drop-in para PIC16F15356-E/SS — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16F15356-E/SS (mesmo formato e footprint) — diferindo em DAC, Package, ADC, Comparators, Program Memory (Flash).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F15355-E/SS
✅ Drop-In✓ Em estoque
$1.18 / unidade
Ver ficha técnica →PIC16F15354-E/SS
✅ Drop-In✓ Em estoque
$0.84 / unidade
Ver ficha técnica →PIC16F15356-I/SS
✅ Drop-In✓ Em estoque
$1.45 / unidade
Ver ficha técnica →PIC16F15356-E/SSVAO
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC18F27K40-E/SS
✅ Drop-In✓ Em estoque
$1.65 / unidade
Ver ficha técnica →PIC18F24K22-I/SSVAO
✅ Drop-In✓ Em estoque
$2.18 / unidade
Ver ficha técnica →PIC16F15356-E/SS Classificações máximas e características elétricas
| Core Architecture | PIC16 8-bit Harvard RISC |
| CPU Bit Width | 8-bit |
| Maximum CPU Clock | 32 MHz |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| Data SRAM | 2 KB |
| Operating Voltage Range | 1.8 V to 5.5 V |
| Faixa de temperatura de operação | -40C to +125C (Extended, -E suffix) |
| Encapsulamento | 28-pin SSOP (SS, 5.30 mm body) |
| Tipo de montagem | Surface Mount |
| ADC | 2x 10-bit ADC, up to 43 channels |
| DAC | 2x 10-bit DAC |
| Analog Comparators | 2 |
| PWM Outputs | 4x 10-bit PWM |
| Configurable Logic Cells (CLC) | 4 |
| Complementary Waveform Generator (CWG) | Yes |
| Numerically Controlled Oscillator (NCO) | Yes |
| Timers | 3 |
| EUSART | 2 |
| MSSP (SPI / I2C) | 2 |
| Low-Power Technology | eXtreme Low-Power (XLP) |
| Memory Access Partition (MAP) | Yes |
| Device Information Area (DIA) | Yes |
| ICSP Programming | PGC/PGD (In-Circuit Serial Programming) |
| Status RoHS | Compliant |
Configuração de pinos do PIC16F15356-E/SS
| Pino 1 | RA2 — General-purpose I/O / analog input |
| Pino 2 | RA3 — General-purpose I/O / analog input |
| Pino 3 | RA4 — General-purpose I/O |
| Pino 4 | RA5 — General-purpose I/O |
| Pino 5 | RA6 — General-purpose I/O |
| Pino 6 | RA7 — General-purpose I/O / oscillator |
| Pino 7 | VSS — Ground reference |
| Pino 8 | RA1 — General-purpose I/O / analog input |
| Pino 9 | RA0 — General-purpose I/O / analog input |
| Pino 10 | RA1 — General-purpose I/O / analog input |
| Pino 11 | RB7 — General-purpose I/O |
| Pino 12 | RB6 — General-purpose I/O / ICSP PGC |
| Pino 13 | RB5 — General-purpose I/O / analog input |
| Pino 14 | RB4 — General-purpose I/O / analog input |
| Pino 15 | RB3 — General-purpose I/O / analog input |
| Pino 16 | RB2 — General-purpose I/O / analog input |
| Pino 17 | RB1 — General-purpose I/O / analog input |
| Pino 18 | RB0 — General-purpose I/O / ICSP PGD |
| Pino 19 | VDD — Positive supply voltage (1.8 V to 5.5 V) |
| Pino 20 | VSS — Ground reference |
| Pino 21 | RC7 — General-purpose I/O |
| Pino 22 | RC6 — General-purpose I/O |
| Pino 23 | RC5 — General-purpose I/O |
| Pino 24 | RC4 — General-purpose I/O |
| Pino 25 | RC3 — General-purpose I/O / SCL |
| Pino 26 | RC2 — General-purpose I/O / SDA |
| Pino 27 | RC1 — General-purpose I/O / analog input |
| Pino 28 | RC0 — General-purpose I/O / analog input |
Aplicações típicas
PIC16F15356-E/SS é adequado para 6 aplicaçãos: Battery-Powered IoT Sensor Node, LED Lighting Controller, Small Motor and Fan Control, Home Appliance User Interface Board, Automotive Body Electronics (with VAO variant), Industrial Sensor Transmitter (4-20 mA Loop Powered).
Battery-Powered IoT Sensor Node
The PIC16F15356-E/SS is an excellent fit for battery-powered IoT sensor nodes where the XLP (eXtreme Low-Power) idle/doze currents in the nanoamp range directly determine battery lifetime. Its 28 KB Flash accommodates protocol stacks for external radios (BLE via RN4871, LoRa, Sub-GHz proprietary), while the 4x CLC and CWG can generate wake-up waveforms autonomously without waking the core. The 2x 10-bit ADC with up to 43 channels handles multi-sensor fusion (temperature, humidity, light, battery monitor) on a single SSOP-28 footprint. Compared to a switching regulator-driven MCU, the PIC16F15356's deterministic interrupt latency and zero-noise core simplifies EMI compliance for sensitive sensor signal chains.
Recomendado
LED Lighting Controller
The PIC16F15356-E/SS suits LED lighting controllers thanks to its 4x 10-bit PWM channels and Complementary Waveform Generator (CWG), which together can drive RGB+W LED strings or half-bridge FET drivers with programmable dead-band and emergency shutoff. The 2x 10-bit DAC provides smooth dimming curves while the 4x CLC cells handle fault detection (over-current, thermal, short circuit) without CPU intervention, keeping the response deterministic. Operating from 1.8 V to 5.5 V the part adapts to both 3.3 V logic LED drivers and 5 V analog control loops. The same SSOP-28 package is shared across the PIC16F153xx family, allowing easy upgrade to higher-memory variants for DMX or DALI protocol firmware without PCB redesign.
Recomendado
Small Motor and Fan Control
For small motor and fan control, the PIC16F15356-E/SS delivers the precise PWM and complementary waveform generation required for BLDC, brushed DC, or stepper motor commutation. The Complementary Waveform Generator (CWG) creates hardware dead-band timing, freeing the CPU from interrupt-heavy switching logic, while the Numerically Controlled Oscillator (NCO) provides fine frequency synthesis for variable-speed drives. The 2 analog comparators enable over-current protection by directly triggering PWM shutdown without software latency. Operating across -40C to +125C the part handles industrial motor enclosures, and its 2 KB SRAM is sufficient for field-oriented control loops in sub-100 W motor designs.
Recomendado
Home Appliance User Interface Board
The PIC16F15356-E/SS is well matched to home appliance user-interface boards where capacitive touch, LED feedback, and serial communication with the main appliance controller coexist. The 2x EUSART and 2x MSSP (SPI/I2C) interfaces can simultaneously drive a main control board link, an LCD, and a sensor front-end, while the 2x 10-bit ADC handles potentiometers and analog front panels. The CIPs (CLC, CWG, NCO) can run autonomous timing sequences for status indicators without burdening the main loop, reducing firmware complexity. The wide 1.8-5.5 V operating range matches both 3.3 V and 5 V appliance rails without external level shifters.
Recomendado
Automotive Body Electronics (with VAO variant)
The PIC16F15356-E/SSVAO variant is AEC-Q100 qualified and designed into automotive body electronics such as interior lighting controllers, seat control modules, and HVAC user-interface panels. The CIPs enable hardware-only LIN message handling, freeing the core for application logic, while the XLP technology supports key-fob proximity detection with multi-year coin-cell battery life. The -40C to +125C operating range covers under-dash and cabin modules. With 28 KB Flash the device fits typical body-control firmware including bootloader and diagnostics, and the SSOP-28 footprint supports dense PCB layouts in space-constrained automotive enclosures.
Recomendado
Industrial Sensor Transmitter (4-20 mA Loop Powered)
The PIC16F15356-E/SS is suitable for loop-powered 4-20 mA industrial sensor transmitters where its nanoamp XLP sleep current keeps total consumption below the 3.5 mA budget required for zero-output current and headroom for the sensor bridge excitation. Its 10-bit ADC paired with an external precision op-amp delivers 16-bit effective resolution for pressure, flow, or level transmitters after oversampling. The 2x DACs can drive 4-20 mA current loops directly via a current-setting op-amp stage. The wide 1.8-5.5 V operating range adapts to 24 V loop supply through low-dropout regulation, and the -E suffix ensures operation from -40C to +125C for outdoor process instrumentation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16F15356-E/SS — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F15355-E/SS | PIC16F15354-E/SS | PIC16F15356-I/SS | PIC16F15356-E/SSVAO | PIC18F27K40-E/SS |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | SSOP-28 | SSOP-28 | SSOP-28 | SSOP-28 | SSOP-28 | SSOP-28 |
| Core Architecture | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC16 8-bit | PIC18 16-bit |
| Max CPU Clock | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 64 MHz |
| Flash Memory | 28 KB | 14 KB | 7 KB | 28 KB | 28 KB | 128 KB |
| SRAM | 2 KB | 1 KB | 512 B | 2 KB | 2 KB | 4 KB |
| Operating Voltage | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V | 1.8 V to 5.5 V |
| Operating Temperature | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +125C (Automotive) | -40C to +125C (Extended) |
| Automotive Grade | No | No | No | No | Yes (AEC-Q100) | No |
Principais diferenciais
- Highest-density Flash in the SSOP-28 PIC16F153xx family (vs PIC16F15355-E/SS)
- Extended industrial temperature grade for harsh environments (vs PIC16F15356-I/SS)
- Automotive-grade option within the same drop-in SSOP-28 footprint (vs PIC16F15356-E/SSVAO)
- Core Independent Peripherals (CIPs) - 4x CLC + CWG + NCO autonomous operation (vs PIC18F27K40-E/SS)
Notas de projeto
Place a 0.1 uF decoupling capacitor within 2 mm of the VDD pin (pin 19) and add a 10 uF bulk capacitor on the supply rail to suppress transient currents during ADC sampling and PWM switching events. The XLP feature keeps nanoamp-range idle currents, but the ADC can draw additional bias current during conversion; route the analog supply through a ferrite bead from VDD if the application requires very low ADC noise.
Reserve the ICSP pins (PGC = RB6, PGD = RB0) for programming/debug access - do not assign them to user functions that would block in-circuit programming. Place a 10 k pull-up resistor on MCLR to allow normal operation; in production the MCLR can be driven by the programmer. Keep the ICSP connector or test pads at the board edge for fixture access during manufacturing test.
The PIC16F15356-E/SS SSOP-28 variant does not bring out all peripheral pins available on larger QFN-44/48 packages. Verify pinout against the datasheet before assuming a peripheral (especially the 43-channel ADC maximum) is available - the 28-pin variant typically exposes fewer GPIO and analog channels. Also ensure that firmware using the MAP (Memory Access Partition) feature is configured before enabling write-protected regions, as a misconfigured MAP can lock out the bootloader.
The SSOP-28 package has limited thermal dissipation (approximately 100 C/W theta_JA on a 1-oz 2-layer board). At maximum 32 MHz CPU clock and full peripheral activity, the core current is approximately 6-8 mA at 5 V, which is thermally negligible. However in hot industrial environments above 85C ambient, ensure the SSOP-28 has at least 50 mm2 of copper pour for thermal relief.
Informações de conformidade
RoHS compliant per Microchip product page. The standard PIC16F15356-E/SS is not AEC-Q100 qualified - choose the PIC16F15356-E/SSVAO suffix variant for AEC-Q100 automotive applications.
