PIC16F18875-E/MV - 8-Bit MCU 32MHz 14KB Flash 40-UQFN | Microchip
N.º da peça: PIC16F18875-E/MV ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $1.85 | $1,85 |
| 10 | $1.74 | $17,40 |
| 100 | $1.55 | $155,00 |
| 500 | $1.39 | $695,00 |
| 1.000 | $1.2 | $1.200,00 |
| 3.000 | $1.05 | $3.150,00 |
PIC16F18875-E/MV Visão geral
An 8-bit microcontroller (MCU) is a single-chip processor whose data path is 8 bits wide, optimized for low-cost, low-power, and deterministic control tasks. The 8-bit MCU hierarchy sits beneath the broader semiconductor and embedded processor taxonomy, and the PIC16F18875 belongs to Microchip's enhanced mid-range PIC16 core family, offering richer peripherals than legacy PIC16F parts while preserving the familiar instruction set. This positions the part between simple 8-bit controllers and 32-bit ARM Cortex-M devices, balancing code density, ease of use, and peripheral integration.
Communication peripherals include EUSART with LIN support, SPI, and I2C, while power management features eXtreme Low Power (XLP) technology with IDLE and DOZE modes plus Peripheral Module Disable (PMD) for fine-grained current control. Functional Safety (FuSa) features simplify IEC 60730 Class B compliance for appliance and industrial designs, making this MCU well-suited for safety-critical and regulated end products.
The 40-UQFN package provides 36 I/O pins across multiple ports with PPS remapping, allowing designers to assign digital peripherals to almost any pin for simplified PCB routing. The exposed thermal pad improves power dissipation for sustained MIPS operation. Typical applications include consumer appliances, industrial sensor interfaces, IoT edge nodes, lighting controls, motor control loops, and battery-powered portable devices where low sleep current and rich analog peripherals reduce BOM cost.
When designing with this device, allocate budget for the ICD 3 or PICkit 4 programming/debug header and ensure the 5x5 mm UQFN land pattern uses NSMD pads with via-in-pad for the thermal pad to maximize heat sinking. The PPS system must be configured before peripheral use, so allow extra code space and runtime for the configuration lock.
Alternativas drop-in para PIC16F18875-E/MV — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16F18875-E/MV (mesmo formato e footprint) — diferindo em Package, ADC, Operating Temperature, Program Memory (Flash), DAC.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F18876-E/MV
✅ Drop-In✓ Em estoque
$1.95 / unidade
Ver ficha técnica →PIC16F18874-E/MV
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F18877-E/MV
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F18854-E/MV
✅ Drop-In✓ Em estoque
$0.72 / unidade
Ver ficha técnica →PIC16F18856-E/MV
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F18855-I/MV
✅ Drop-In✓ Em estoque
$1.22 / unidade
Ver ficha técnica →PIC16F18875-E/MV Classificações máximas e características elétricas
| Core Processor | PIC |
| Core Size | 8-Bit |
| Maximum Clock Speed | 32 MHz |
| Program Memory (Flash) | 14 KB (8K x 14) |
| RAM Size | 1 KB |
| EEPROM Size | 256 B |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Encapsulamento | 40-UQFN (5x5 mm) Exposed Pad |
| Number of I/O Pins | 36 |
| ADC | 10-bit ADC2 (Computation) |
| DAC | 5-bit / 8-bit |
| Comparators | Yes |
| PWM Modules | Yes (with CWG) |
| Communication Interfaces | EUSART (LIN), SPI, I2C |
| Faixa de temperatura de operação | -40C to +125C (Extended, -E suffix) |
| Peripheral Pin Select (PPS) | Yes |
| Watchdog Timer | WWDT (Windowed) |
| Low-Power Modes | XLP, IDLE, DOZE, PMD |
| Functional Safety (FuSa) | Yes (IEC 60730 Class B support) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do PIC16F18875-E/MV
| Pino 1 | RA3/SS1 — I/O / SPI Slave Select |
| Pino 2 | RA4 — I/O / CPP |
| Pino 3 | RA5 — I/O / Vcap |
| Pino 4 | RA6 — I/O |
| Pino 5 | RA7 — I/O |
| Pino 6 | RB0 — I/O / Interrupt-on-change |
| Pino 7 | RB1 — I/O / Interrupt-on-change |
| Pino 8 | RB2 — I/O / Interrupt-on-change |
| Pino 9 | RB3 — I/O / Interrupt-on-change |
| Pino 10 | RB4 — I/O / Interrupt-on-change |
| Pino 11 | RB5 — I/O / Interrupt-on-change |
| Pino 12 | RB6 — I/O / PGC |
| Pino 13 | RB7 — I/O / PGD |
| Pino 14 | VDD — Positive Supply (2.3V-5.5V) |
| Pino 15 | VSS — Ground |
| Pino 16 | RC0 — I/O |
| Pino 17 | RC1 — I/O |
| Pino 18 | RC2 — I/O |
| Pino 19 | RC3 — I/O / SCL |
| Pino 20 | RC4 — I/O / SDA |
| Pino 21 | RC5 — I/O |
| Pino 22 | RC6 — I/O / TX |
| Pino 23 | RC7 — I/O / RX |
| Pino 24 | RE3/MCLR — Reset / Master Clear (input) |
| Pino 25 | RD0 — I/O |
| Pino 26 | RD1 — I/O |
| Pino 27 | RD2 — I/O |
| Pino 28 | RD3 — I/O |
| Pino 29 | RD4 — I/O |
| Pino 30 | RD5 — I/O |
| Pino 31 | RD6 — I/O |
| Pino 32 | RD7 — I/O |
| Pino 33 | RE0 — I/O |
| Pino 34 | RE1 — I/O |
| Pino 35 | RE2 — I/O |
| Pino 36 | RA0 — I/O / AN0 |
| Pino 37 | RA1 — I/O / AN1 |
| Pino 38 | RA2 — I/O / AN2 |
| Pino 39 | NC — Not connected (per datasheet) |
| Pino 40 | NC — Not connected (per datasheet) |
Aplicações típicas
PIC16F18875-E/MV é adequado para 6 aplicaçãos: Consumer Appliance Control, Industrial Sensor Interface Node, IoT Edge Node and Wearable Hub, LED Lighting and Color Control, Automotive Body Electronics (LIN Sub-Nodes), Battery-Operated Handheld Instruments.
Consumer Appliance Control
The PIC16F18875-E/MV suits consumer appliances such as washing machines, dishwashers, and induction cooktops thanks to Functional Safety (FuSa) IEC 60730 Class B support and rich Core Independent Peripherals. The 10-bit ADC2 with Computation captures sensor inputs (temperature, current, water level) without CPU overhead, while the CWG and PWM modules drive motor control loops for pumps and fans. The 36 I/O pins and PPS routing handle multiple HMI keypads, LED indicators, and rotary encoders in a single chip.
Recomendado
Industrial Sensor Interface Node
The PIC16F18875-E/MV is ideal for industrial 4-20 mA loop-powered sensor transmitters and Modbus RTU slave nodes, leveraging its EUSART (LIN/RS-485 capable) and SPI/I2C peripherals. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V analog front-ends, while the on-chip comparators and ZCD enable zero-cross detection for AC line-powered designs. XLP low-power modes with sub-microamp sleep current extend battery life in remote or wireless sensor nodes.
Recomendado
IoT Edge Node and Wearable Hub
The PIC16F18875-E/MV serves as an edge-processing MCU for IoT wearable hubs and Bluetooth/BLE bridge nodes, where the 14 KB Flash can run local decision logic before forwarding to a higher-level radio module. PPS lets the designer route SPI signals to the BLE module on any convenient pin, simplifying small-form-factor PCB layout. With XLP nanoWatt sleep and IDLE/DOZE modes, the device achieves years of battery life on a single coin cell in periodic-sensing applications.
Recomendado
LED Lighting and Color Control
The PIC16F18875-E/MV drives multi-channel LED lighting controllers and DMX512-compatible fixtures using its PWM, CWG, and 10-bit ADC2 peripherals. The 5/8-bit DAC and comparators enable smooth dimming curves and analog current feedback loops for constant-current LED drivers. With up to 36 I/O pins and PPS flexibility, the MCU easily handles RGBW strips, addressable LED protocols, and capacitive touch UI for smart lighting applications.
Recomendado
Automotive Body Electronics (LIN Sub-Nodes)
The PIC16F18875-E/MV fits automotive body-electronics sub-nodes such as window lift, seat control, and mirror adjustment modules thanks to on-chip EUSART with LIN 1.3/2.0/2.1 host and client support. The CRC/SCAN and Windowed Watchdog Timer (WWDT) provide the safety primitives required for ISO 26262-ready subsystems. The 32 MHz core runs LIN scheduling and actuator PWM loops in a single deterministic thread.
Recomendado
Battery-Operated Handheld Instruments
The PIC16F18875-E/MV is well-suited for portable test instruments, handheld scanners, and medical point-of-care devices where its XLP low-power modes minimize battery drain. The 32 MHz performance runs user-interface graphics, ADC2-based sensor reads, and USB-to-UART bridges through EUSART, while the 1 KB SRAM buffers measurement data. The wide 2.3 V to 5.5 V supply range supports direct Li-Ion battery operation without external regulation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16F18875-E/MV — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F18876-E/MV | PIC16F18874-E/MV | PIC16F18854-E/MV | PIC16F18856-E/MV | PIC16F18855-I/MV |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 40-UQFN (5x5) | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same | 40-UQFN (5x5) - same |
| Flash Memory | 14 KB | 28 KB | 7 KB | 7 KB | 28 KB | 14 KB |
| RAM | 1 KB | 2 KB | 512 B | 512 B | 2 KB | 1 KB |
| Clock Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| I/O Pins | 36 | 36 | 36 | 36 | 36 | 36 |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Temperature Grade | -40C to +125C (Extended) | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +125C | -40C to +85C (Industrial) |
| Peripheral Pin Select (PPS) | Yes | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Functional Safety (FuSa) IEC 60730 Class B support (vs PIC16F18854-E/MV)
- 40-UQFN (5x5) package option preserves more I/O than 28-pin siblings (vs PIC16F18855-I/MV)
- Peripheral Pin Select (PPS) on all digital peripherals (vs Legacy PIC16F877A)
Notas de projeto
The 40-UQFN (5x5) package has an exposed thermal pad that must be soldered to a 5x5 mm copper pad with via-in-pad stitching to maximize heat dissipation. Use Non-Solder Mask Defined (NSMD) land patterns with 0.2 mm pad pitch and 0.4 mm via diameter. Place decoupling capacitors (100 nF + 1 uF) within 2 mm of VDD/VSS pins to minimize switching noise on 32 MHz core transitions.
Enable the on-board Voltage Regulator (VCAP) and place a 1 uF ceramic capacitor at the VCAP pin (RA5) when using the device without an external regulator. For battery applications, leverage the XLP sleep mode with Watchdog Timer (WDT) wake-up for currents below 1 uA typical. Always ramp VDD monotonically and respect the minimum rise-time specification to avoid malfunction during power-on.
Always configure Peripheral Pin Select (PPS) before enabling peripherals; PPS registers are unlocked after a reset and must be written with the unlock sequence (PPSLOCKED bit). Unused I/O pins should be configured as outputs low or inputs with internal pull-ups to minimize power consumption and avoid floating inputs. The ICD 3 / PICkit 4 debugger must connect to RB6 (PGC) and RB7 (PGD) - reserve these pins or remap debug via PPS only with caution.
Informações de conformidade
RoHS compliant per Microchip product page. AEC-Q100 not qualified - use PIC16F15356 or PIC18F K-series for automotive-grade. Functional Safety IEC 60730 Class B supported but requires firmware library (AN2744).
