PIC16LCE623-04E/SO - 4MHz 8-bit OTP MCU 896B | Microchip
N.º da peça: PIC16LCE623-04E/SO ⚠ Última compra| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $3.05 | $30,50 |
| 100 | $2.71 | $271,00 |
| 500 | $2.42 | $1.210,00 |
| 1.000 | $2.15 | $2.150,00 |
PIC16LCE623-04E/SO Visão geral
An 8-bit OTP microcontroller is a single-chip computer built around a Harvard-architecture CPU with non-volatile one-time-programmable program memory, distinct from flash-based MCUs that allow multiple erase/write cycles. OTP parts ship blank and are programmed once by the user, which reduces unit cost versus flash parts and makes them suited to mature production runs where firmware is finalized and code protection is enforced by the inability to read back the program. In the broader taxonomy, this device belongs to microcontrollers -> embedded controllers -> ICs, and within the PIC16 family it represents an early-generation low-cost general-purpose MCU optimized for simple control loops, user-interface scanning, and appliance logic.
Key features include a 4 MHz maximum clock, 200 ns single-cycle instruction execution (except 2-cycle branches), 35 single-word RISC-style instructions, an analog comparator module, a watchdog timer with on-chip RC oscillator, in-circuit serial programming (ICSP) via two pins, and power-saving SLEEP mode with wake-up on pin change. The PIC16LCE623-04E/SO also supports power-on reset, brown-out reset, and code-protection fuses.
The architecture uses a 14-bit instruction word with separate program and data buses (Harvard), enabling simultaneous instruction fetch and operand access. The internal oscillator reference for the watchdog is RC-based and independent of the system clock, which simplifies BOM by removing an external watchdog resistor.
Typical applications include white-goods and appliance control panels, remote-keyless-entry keyfobs, simple sensor interfaces, low-power battery indicator circuits, and replacement of discrete logic in cost-sensitive industrial equipment.
When designing with this device, ensure the VDD supply is decoupled with 100 nF ceramic close to the pin pair, route the ICSP clock/data lines to a 5-pin header for in-system programming, and reserve the MCLR pin configuration carefully because enabling internal weak pull-up eliminates the need for an external reset RC network.
This page synthesizes distributor stock, parametric depth, and drop-in alternatives beyond what is shown in the manufacturer datasheet, helping procurement and design engineers validate a replacement or finalize a long-life BOM.
Alternativas drop-in para PIC16LCE623-04E/SO — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16LCE623-04E/SO (mesmo formato e footprint) — diferindo em Internal Oscillator, Package, Instruction Set, Operating Temperature, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F628-04/SO
✅ Drop-In✓ Em estoque
$1.05 / unidade
Ver ficha técnica →PIC16F627-04/SO
✅ Drop-In✓ Em estoque
$1.85 / unidade
Ver ficha técnica →PIC16F628A-I/SO
✅ Drop-In✓ Em estoque
$2.32 / unidade
Ver ficha técnica →PIC16F630-I/SO
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F648A-I/SO
✅ Drop-In✓ Em estoque
$2.1 / unidade
Ver ficha técnica →PIC16LCE621-04E/SO
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16LCE623-04E/SO Classificações máximas e características elétricas
| Product Type | 8-bit OTP Microcontroller |
| Family | PIC16C (PIC16LCE62x series) |
| Core Architecture | RISC Harvard, 14-bit instruction word |
| Program Memory Size | 896 bytes (512 x 14 words), OTP |
| Data RAM Size | 96 bytes |
| Number of I/O Pins | 13 |
| Frequência máxima de clock | 4 MHz |
| Instruction Cycle Time | 200 ns (single-cycle) |
| Instruction Set Size | 35 instructions |
| Supply Voltage (VDD) | 3.0 V to 3.6 V (LC low-voltage family) |
| Temperatura de operação | -40 C to +125 C (extended grade, 'E' suffix) |
| Encapsulamento / Caixa | 18-SOIC (0.295 in / 7.50 mm body width) |
| Tipo de montagem | Surface Mount |
| Oscillator Type | External RC/HS/XT (datasheet external clock input) |
| Peripherals | Analog comparator, 8-bit timer/counter, watchdog timer, ICSP |
Configuração de pinos do PIC16LCE623-04E/SO
| Pino 1 | RA2/AN2/VREF — PORTA bit 2 / analog input / voltage reference |
| Pino 2 | RA3/AN3/CMP1 — PORTA bit 3 / analog input / comparator-1 output |
| Pino 3 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pino 4 | RA5/MCLR/VPP — PORTA bit 5 / Master Clear (reset) input / programming voltage |
| Pino 5 | VSS — Ground reference |
| Pino 6 | RB0/INT — PORTB bit 0 / external interrupt input |
| Pino 7 | RB1 — PORTB bit 1 |
| Pino 8 | RB2 — PORTB bit 2 |
| Pino 9 | RB3 — PORTB bit 3 |
| Pino 10 | RB4 — PORTB bit 4 |
| Pino 11 | RB5 — PORTB bit 5 |
| Pino 12 | RB6 — PORTB bit 6 / ICSP clock |
| Pino 13 | RB7 — PORTB bit 7 / ICSP data |
| Pino 14 | VDD — Positive supply (3.0 V - 3.6 V) |
| Pino 15 | OSC2/CLKOUT — Oscillator crystal output / clock-out |
| Pino 16 | OSC1/CLKIN — Oscillator crystal input / external clock in |
| Pino 17 | RA0/AN0 — PORTA bit 0 / analog input 0 |
| Pino 18 | RA1/AN1 — PORTA bit 1 / analog input 1 |
Aplicações típicas
PIC16LCE623-04E/SO é adequado para 6 aplicaçãos: White-Goods Appliance Control, Remote Keyless Entry Keyfobs, Industrial Sensor Interface Modules, Battery-Powered Indicator Circuits, Low-Cost Replacement of Discrete Logic, Automotive Cabin Accessories.
White-Goods Appliance Control
The PIC16LCE623-04E/SO suits washing machine, dishwasher and refrigerator control boards because its 13 I/O pins drive relays, triac optos and 7-segment displays directly without external logic. The 4 MHz clock and 35-instruction RISC core handle timing, sensor polling and user-input debouncing in a single-chip design. The OTP program memory prevents firmware reverse-engineering and the LC 3.3 V rail aligns with modern switch-mode supplies that already produce 3.3 V for digital logic, eliminating a regulator.
Recomendado
Remote Keyless Entry Keyfobs
Battery-powered keyfobs benefit from the PIC16LCE623-04E/SO's 3.0-3.6 V LC supply and low SLEEP-mode current. The 8-bit timer/counter and on-chip analog comparator support debounced button input and RF enable pulses, while the 13 I/O pins accommodate multi-button matrices and LED indicators. OTP memory ensures the rolling-code firmware cannot be read back, raising security in a cost-sensitive consumer product.
Recomendado
Industrial Sensor Interface Modules
In industrial 4-20 mA loop detectors and proximity-sensor interfaces the PIC16LCE623-04E/SO provides the on-chip analog comparator needed to threshold sensor signals, freeing the 13 I/O for indicator LEDs, H-bridge enable lines and isolated UART outputs. The extended -40 C to +125 C temperature grade suits factory-floor cabinets, and OTP memory locks the calibration constants against field tampering once the design is qualified.
Recomendado
Battery-Powered Indicator Circuits
Battery-powered fuel-gauges, low-battery alerts and self-powered safety sensors use the PIC16LCE623-04E/SO in SLEEP mode most of the time, waking on a comparator edge to drive an LED or piezo buzzer. The LC 3.3 V supply matches single-cell LiFePO4 or two-alkaline topologies directly, reducing quiescent losses and BOM cost. OTP memory protects the trip thresholds from external observation.
Recomendado
Low-Cost Replacement of Discrete Logic
Replacing 74HC00-series glue logic with a PIC16LCE623-04E/SO delivers up to 13 programmable I/O at lower PCB area and unit cost once volumes exceed a few thousand. Engineers can encode sequential state machines, timing patterns and conditional outputs in firmware rather than gates, accelerating design changes. The 18-SOIC footprint is also breadboard-friendly and easy to hand-prototype before committing to PCB layout.
Recomendado
Automotive Cabin Accessories
Although not AEC-Q100 qualified, the PIC16LCE623-04E/SO extended -40 C to +125 C grade fits non-safety cabin accessories such as ambient lighting controllers, vanity-mirror logic, and seat-position memory switches. The OTP memory and 3.3 V LC supply keep quiescent draw low on accessory rails, and the 13 I/O drive LED arrays and switch matrices without external muxing.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16LCE623-04E/SO — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F628-04/SO | PIC16F627-04/SO | PIC16F628A-I/SO | PIC16F630-I/SO | PIC16F648A-I/SO |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 18-SOIC (7.50 mm) | 18-SOIC (7.50 mm) - same | 18-SOIC (7.50 mm) - same | 18-SOIC (7.50 mm) - same | 18-SOIC (7.50 mm) - same | 18-SOIC (7.50 mm) - same |
| Program Memory | 896 B (512 x 14) OTP | 2K x 14 Flash | 1K x 14 Flash | 2K x 14 Flash | 1K x 14 Flash | 4K x 14 Flash |
| Data RAM | 96 B | 224 B | 128 B | 224 B | 64 B | 256 B |
| Max Clock Frequency | 4 MHz | 4 MHz | 4 MHz | 20 MHz | 20 MHz | 20 MHz |
| Supply Voltage | 3.0 - 3.6 V (LC) | 3.0 - 5.5 V | 3.0 - 5.5 V | 2.0 - 5.5 V | 2.0 - 5.5 V | 2.0 - 5.5 V |
| Memory Type | OTP | Flash | Flash | Flash | Flash | Flash |
| I/O Pins | 13 | 16 | 16 | 16 | 12 | 16 |
| Operating Temperature | -40 C to +125 C | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) | -40 C to +85 C (industrial) |
Principais diferenciais
- Lowest-cost 18-SOIC OTP mid-range PIC16 in 3.3 V LC family (vs PIC16F628-04/SO)
- Pin-compatible with full PIC16F62x flash family (vs PIC16F628A-I/SO)
- Includes on-chip analog comparator in 18-pin budget (vs PIC16F630-I/SO)
Notas de projeto
Decouple the VDD pin (14) with a 100 nF ceramic capacitor placed within 5 mm of the package and tie the VSS pin (5) to a low-impedance ground pour. The PIC16LCE623-04E/SO LC variant requires 3.0 V to 3.6 V on VDD; running below 3.0 V risks brown-out reset, while exceeding 3.6 V violates the absolute-maximum rating. For battery applications add a bulk 10 uF tantalum or polymer capacitor to absorb regulator sag during RF bursts.
OTP program memory cannot be erased, so any firmware bug that ships to production becomes permanent. Develop and qualify the firmware on a flash-based PIC16F628 or PIC16F627 in the same 18-SOIC footprint, then commit to the OTP PIC16LCE623-04E/SO only after code-freeze. Always enable code-protection fuses (CP) before sealing the part to prevent optical or electrical read-back of firmware.
Route ICSP clock (RB6) and ICSP data (RB7) to a 5-pin header (VPP, VDD, VSS, RB6, RB7) using short, parallel traces. Keep the MCLR/VPP line free of large capacitance so the programmer can pull VPP above VDD quickly during programming. Place the crystal or resonator within 5 mm of OSC1/OSC2 with the load capacitors grounded to a quiet analog-style ground pour.
When using the on-chip analog comparator, isolate the analog input pins (RA0-RA3) from switching digital lines and add a small RC low-pass filter (1 kohm + 100 nF) on noisy sensor lines. The comparator can be a source of supply-current spikes that couple back into VDD; a 100 nF decoupling cap directly on VDD prevents this from triggering brown-out events.
Informações de conformidade
RoHS / REACH / lead-free / halogen status not stated in the verified web data; specific lots may comply but confirmation from Microchip-direct or DigiKey product record is recommended. The part is not AEC-Q100 qualified; for safety-critical automotive systems select an AEC-Q100-qualified PIC16 variant. Last-time-buy lifecycle status implies future RoHS exemption via EOL is unlikely - confirm with Microchip.