PIC16LCE624-04I/P - 1.75KB OTP 8-bit MCU, 4MHz | Microchip
N.º da peça: PIC16LCE624-04I/P ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.63 | $2,63 |
| 10 | $2.41 | $24,10 |
| 100 | $2.19 | $219,00 |
| 500 | $1.99 | $995,00 |
| 1.000 | $1.85 | $1.850,00 |
PIC16LCE624-04I/P Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripherals. The PIC16LCE624 belongs to Microchip's mid-range PIC16 family, which uses a 14-bit instruction set and Harvard architecture to deliver deterministic interrupt latency and predictable execution timing, while the 'L' suffix denotes the low-voltage (2.5V-5.5V) operation characteristic of this product line. This positions the device within the hierarchy of MCU -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor.
Key features include a 4MHz maximum operating clock frequency, 1.75KB (1K x 14) One-Time-Programmable (OTP) program memory, 96 bytes of data RAM, 128 bytes of EEPROM data memory, an internal analog comparator, capture/compare/PWM (CCP) module, and a 10-bit ADC that distinguishes this MCU from the smaller PIC16CE62x siblings.
The architecture combines a RISC instruction set with Harvard bus separation, allowing simultaneous instruction fetch and data access. The wide 2.5V-5.5V operating range supports both 3.3V and 5V designs, while the OTP memory allows rapid prototyping and low-volume production without the cost of windowed or flash devices. Built-in peripherals minimize external component count, lowering BOM cost for cost-sensitive embedded designs.
Typical applications include low-power industrial control loops, sensor interface front-ends, consumer appliance controllers, and legacy product maintenance systems where original PIC16CE624 sockets need a low-voltage drop-in replacement. The 18-pin DIP package simplifies prototyping on breadboards and through-hole PCB assemblies.
When designing with this part, note that OTP memory cannot be reprogrammed; if in-field updates are required, choose a flash-based sibling such as PIC16F62x. Always include a 0.1uF decoupling capacitor on VDD adjacent to the pin, and respect the absolute maximum VDD of 6.5V to avoid latch-up.
This page synthesizes current distributor pricing for the PIC16LCE624-04I/P, an 8-MHz-limited 4MHz drop-in alternatives list, and practical design notes that complement the manufacturer datasheet rather than duplicate it.
Alternativas drop-in para PIC16LCE624-04I/P — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16LCE624-04I/P (mesmo formato e footprint) — diferindo em Package, Instruction Cycle Time, Timers, Core Architecture, Mounting Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16LCE624-04E/P
✅ Drop-In✓ Em estoque
$4.05 / unidade
Ver ficha técnica →PIC16CE624-04I/P
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.94 / unidade
Ver ficha técnica →PIC16LCE623-04/P
✅ Drop-In✓ Em estoque
$1.45 / unidade
Ver ficha técnica →PIC16LC711-04I/P
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16F628A-I/P
✅ Drop-In✓ Em estoque
$1.62 / unidade
Ver ficha técnica →PIC16LCE624-04I/P Classificações máximas e características elétricas
| Core Architecture | 8-bit PIC RISC (Harvard) |
| Instruction Set | 14-bit (mid-range) |
| Program Memory | 1.75 KB (1K x 14) OTP |
| Data RAM | 96 bytes |
| EEPROM Data Memory | 128 bytes |
| I/O Pins | 13 |
| Frequência máxima de clock | 4 MHz |
| Operating Voltage (VDD) | 2.5 V to 5.5 V |
| ADC | 10-bit (single channel) |
| Analog Comparator | Yes (internal) |
| Capture/Compare/PWM (CCP) | 1 module |
| Timers | Timer0, Timer1, Timer2 |
| Encapsulamento | 18-pin DIP (0.300 inch, 7.62mm) |
| Tipo de montagem | Through-Hole |
| Temperature Grade | Industrial (-40C to +85C) |
| Contagem de pinos | 18 |
| Nível MSL | Not applicable (non-SMD) |
| Status RoHS | Compliant |
Configuração de pinos do PIC16LCE624-04I/P
| Pino 1 | RA2/AN2 — GPIO / analog input channel 2 |
| Pino 2 | RA3/AN3 — GPIO / analog input channel 3 |
| Pino 3 | RA4/T0CKI — GPIO / Timer0 clock input |
| Pino 4 | RA5/MCLR/VPP — GPIO / Master Clear (reset) / programming voltage |
| Pino 5 | VSS — Ground reference |
| Pino 6 | RB0/INT — GPIO / external interrupt input |
| Pino 7 | RB1 — GPIO port B bit 1 |
| Pino 8 | RB2 — GPIO port B bit 2 |
| Pino 9 | RB3/PGM — GPIO / low-voltage programming input |
| Pino 10 | RB4 — GPIO port B bit 4 |
| Pino 11 | RB5 — GPIO port B bit 5 |
| Pino 12 | RB6/PGC — GPIO / ICSP clock input |
| Pino 13 | RB7/PGD — GPIO / ICSP data input/output |
| Pino 14 | VDD — Positive supply voltage (2.5V-5.5V) |
| Pino 15 | OSC2/CLKOUT — Oscillator output / clock output |
| Pino 16 | OSC1/CLKIN — Oscillator input / external clock input |
| Pino 17 | RC0 — GPIO port C bit 0 |
| Pino 18 | RC1 — GPIO port C bit 1 |
Aplicações típicas
PIC16LCE624-04I/P é adequado para 6 aplicaçãos: Low-Power Industrial Control, Consumer Appliance Controllers, Legacy Equipment Maintenance, Sensor Interface Front-Ends, Battery-Powered Embedded Nodes, Educational and Hobbyist Prototyping.
Low-Power Industrial Control
The PIC16LCE624-04I/P fits low-power industrial control applications because of its 2.5V-5.5V operating range, 4MHz max clock, and built-in 10-bit ADC plus analog comparator, which eliminate external signal-conditioning parts in a typical sensor-interface loop. The 13 GPIO pins comfortably drive status LEDs, optocouplers, and relay coils directly, each rated to 25mA source/sink per pin, and the 128-byte EEPROM provides non-volatile storage for calibration constants and trip thresholds. Compared with switching to a discrete analog front end, this single-chip integration simplifies regulator cleanup, expand headroom for hysteresis design, and reduces BOM cost in PLC-style input modules, limit-switch interfaces, and process-control sensor nodes that operate from a 24V industrial bus stepped down to 5V.
Recomendado
Consumer Appliance Controllers
The PIC16LCE624-04I/P is a strong fit for cost-sensitive consumer appliance controllers such as coffee machines, washing-machine sub-modules, and HVAC damper actuators. The wide 2.5V-5.5V supply accepts both 3.3V sensor rails and 5V relay-driver rails directly, while the integrated 10-bit ADC reads thermistor and pressure-sensor analog signals without an external converter. OTP memory prevents field firmware tampering, an asset for safety-certified appliance designs, and the 18-pin DIP package simplifies through-hole PCB assembly favored in low-volume appliance production. Compared to a 32-bit MCU, this part delivers just enough MIPS at 4MHz with deterministic interrupts for simple PID loops, while reducing unit cost and regulator thermal stress in compact appliance enclosures.
Recomendado
Legacy Equipment Maintenance
The PIC16LCE624-04I/P supports legacy equipment maintenance by offering a pin-compatible low-voltage replacement for the original PIC16CE624 used in 1990s-2000s-era embedded controllers. Its 18-pin DIP footprint matches the original through-hole PCB pads, eliminating the need for adapter boards or rewiring when a service shop replaces a failed original MCU. The OTP memory is intentional here because the firmware image is already validated, and the low-voltage 2.5V-5.5V range matches modernized 3.3V power rails that have replaced the original 5V supplies. Compared to redesigning the legacy system around a new MCU, this drop-in replacement shortens Mean Time To Repair (MTTR), preserves mechanical fit, and keeps test fixtures valid for industrial controls, elevator sub-boards, and specialty machinery still in service worldwide.
Recomendado
Sensor Interface Front-Ends
The PIC16LCE624-04I/P is well suited to sensor interface front-ends because its on-chip 10-bit ADC, internal analog comparator, and CCP/PWM peripherals cover the typical signal-conditioning and actuator-drive tasks in a single IC. Operating from 2.5V-5.5V, the device can be powered directly from a single-cell Li-ion pack (3.7V nominal) or from a regulated 5V rail in industrial instrumentation. The 96-byte RAM and 1.75KB OTP support small FSMs that scan a sensor, debounce inputs, and drive a PWM output to a fan or heater without an external DSP. Compared with a discrete op-amp + comparator + timer design, this single-chip integration lowers quiescent current, reduces PCB area, and gives the design engineer a software-configurable update rate that is impractical to achieve with hard-wired analog circuits.
Recomendado
Battery-Powered Embedded Nodes
The PIC16LCE624-04I/P works in battery-powered embedded nodes thanks to its low-voltage 2.5V-5.5V operation and the inherent low power of the 8-bit PIC core at 4MHz. Sleep current at 3.0V is in the microamp range, allowing duty-cycled wake-up schedules for remote sensors that spend most of their life in standby, waking only to take a measurement and transmit. The 128-byte EEPROM retains calibration data across sleep cycles without external non-volatile memory, and the 13 GPIO pins provide enough channels for a UART bit-banged interface to a low-power RF module. Compared to higher-MIPS 32-bit MCUs, this part trades processing speed for far lower active and sleep current, which is the deciding factor for solar or coin-cell powered sensor nodes where energy budget dominates BOM choice.
Recomendado
Educational and Hobbyist Prototyping
The PIC16LCE624-04I/P is a strong match for educational and hobbyist prototyping because the 18-pin DIP package drops directly into a solderless breadboard, allowing students to build and test circuits without a custom PCB. The 4MHz clock limit is intentional, ensuring students can calculate timing by hand and verify instruction cycles on an oscilloscope or logic analyzer. The OTP memory teaches the practical engineering trade-off between one-time-programmable cost and flash reprogrammability, while the 13 GPIO pins cover classic projects such as LED chasers, servo drivers, and serial-monitored thermometers. Compared with modern 32-bit dev boards, this part constrains the design to fundamentals - I/O, timers, and ADC - building the foundation engineers need before adopting more complex microcontrollers.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16LCE624-04I/P — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16LCE624-04E/P | PIC16CE624-04I/P | PIC16LCE623-04/P | PIC16LC711-04I/P | PIC16F628A-I/P |
|---|---|---|---|---|---|---|
| Package | 18-pin DIP | 18-pin DIP - same | 18-pin DIP - same | 18-pin DIP - same | 18-pin DIP - same | 18-pin DIP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 1.75 KB OTP | 1.75 KB OTP | 1.75 KB EPROM (windowed) | 896 B (0.875 KB) OTP | 1.75 KB OTP | 3.5 KB Flash |
| Max Clock | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 4 MHz | 20 MHz |
| Operating Voltage | 2.5 V to 5.5 V | 2.5 V to 5.5 V | 4.0 V to 6.0 V | 2.5 V to 5.5 V | 2.5 V to 6.0 V | 2.0 V to 5.5 V |
| ADC | 10-bit, multi-channel | 10-bit, multi-channel | 10-bit, multi-channel | No ADC | 8-bit, multi-channel | No ADC (comparator only) |
| Memory Type | OTP | OTP | EPROM (windowed) | OTP | OTP | Flash |
| Lifecycle | NRND | Active | Obsolete | NRND | Obsolete | Active |
Principais diferenciais
- Low-voltage 2.5V-5.5V operation with integrated 10-bit ADC (vs PIC16CE624-04I/P)
- One-Time-Programmable memory prevents firmware tampering (vs PIC16F628A-I/P)
- Built-in 10-bit ADC eliminates external converter in sensor nodes (vs PIC16LCE623-04/P)
Notas de projeto
Place a 0.1uF ceramic decoupling capacitor as close as possible to the VDD pin (pin 14) of the PIC16LCE624-04I/P, with a 10uF bulk capacitor on the same supply rail to handle inrush during oscillator startup. For battery-powered designs, switch the MCU into SLEEP mode between sensor reads and rely on the internal analog comparator as a wake-up source; according to the manufacturer datasheet, sleep current is in the microamp range at 3.0V.
Never assume OTP memory can be re-written; the PIC16LCE624-04I/P is one-time-programmable and rejected code commits will require a new part. Always validate firmware on a flash-based sibling (e.g. PIC16F628A-I/P) or an emulator before committing code to the OTP MCU. Also respect the absolute maximum VDD of 6.5V - the 'L' suffix guarantees only 5.5V normal operation, and exceeding the absolute max causes latch-up.
Keep the trace between the OSC1/OSC2 pins (16/15) and the crystal short (<10mm) and guard them with a ground pour to reduce EMI pickup. The MCLR/VPP pin (pin 4) must rise to VPP during ICSP programming; provide either a dedicated programming header or a 10k pull-up plus a manual reset button. Tie unused GPIO pins to defined logic levels (VDD or VSS) to minimize supply-current creep during SLEEP.
Informações de conformidade
RoHS and REACH compliance confirmed on Microchip product page. Not AEC-Q100 qualified - this part targets industrial and consumer markets, not automotive.
