PIC16LF1776T-I/SO - 8-Bit 32MHz MCU 14KB Flash 28-SOIC | Microchip
N.º da peça: PIC16LF1776T-I/SO ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $2.42 | $2,42 |
| 10 | $2.18 | $21,80 |
| 100 | $1.94 | $194,00 |
| 500 | $1.72 | $860,00 |
| 1.000 | $1.51 | $1.510,00 |
| 2.600 | $1.34 | $3.484,00 |
PIC16LF1776T-I/SO Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), data memory (RAM), peripherals and I/O on one IC. The PIC16F family uses a RISC-based 8-bit core optimized for deterministic, low-latency control loops, while the "LF" prefix indicates the wide-voltage, low-power variant suitable for battery and energy-harvesting systems. PIC MCUs sit in the broader semiconductor hierarchy: microcontroller -> embedded processor -> integrated circuit, and are widely deployed where predictable real-time behavior matters more than raw compute throughput.
Key features of the PIC16LF1776 include 14KB self-programmable Flash (8K × 14 words), 1KB RAM, four 10-bit DACs, two op-amps, two high-speed comparators, programmable ramp generator (PRG), zero-cross detect (ZCD), complementary waveform generators for 10/16-bit PWMs, 100 mA capable I/Os, peripheral pin select (PPS), and serial interfaces including SPI, I²C and EUSART. The wide 1.8V-3.6V Vdd range plus XLP™ nanoWatt technology extends battery life in always-on designs.
The architecture pairs a Harvard RISC core with an on-chip 32MHz oscillator and Microchip's Core Independent Peripherals (CIPs) — peripherals that run without CPU intervention. This combination enables accurate, deterministic closed-loop control for LED drivers, digital power supplies, and BLDC motor commutation without burdening the main core.
Typical applications include high-performance LED lighting with dimming and color-mixing, switched-mode power supplies with digital compensation, battery-charging and battery-management systems, sensor signal conditioning, industrial control loops, and small motor-control boards. The on-chip 10-bit DACs and op-amps simplify analog front-ends, while the 100 mA I/Os can directly drive LED strings or small relays.
When designing with this part, leverage PPS to remap peripherals to almost any I/O pin, easing PCB layout, and use the complementary PWM outputs together with the programmable ramp generator for high-resolution, dead-band-controlled power-stage timing. For power budgeting, the XLP™ sleep current in the nanoamp range is critical for long-life battery or energy-harvesting products.
This page consolidates distributor stock and pricing, drop-in alternatives, and practical design guidance beyond what the manufacturer datasheet alone provides, helping engineers evaluate and source the PIC16LF1776T-I/SO efficiently.
Alternativas drop-in para PIC16LF1776T-I/SO — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16LF1776T-I/SO (mesmo formato e footprint) — diferindo em Core Architecture, Package, Program Memory (Flash), Family, I/O Pins.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16LF1776-I/SO
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.74 / unidade
Ver ficha técnica →PIC16F1776-I/SO
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.81 / unidade
Ver ficha técnica →PIC16LF1777-I/SO
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16LF1778-I/SO
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16LF1776T-I/SO Classificações máximas e características elétricas
| Core Architecture | PIC 8-bit RISC (Harvard) |
| Family | PIC® XLP™ 16F, PIC16LF177x series |
| Program Memory (Flash) | 14 KB (8K × 14 words) |
| RAM | 1 KB |
| Maximum CPU Frequency | 32 MHz |
| Operating Voltage (Vdd) | 1.8 V to 3.6 V |
| Encapsulamento | 28-SOIC (0.295", 7.50 mm width) |
| I/O Pins | Up to 25 (100 mA sink/source capable) |
| 10-bit DAC | 4 channels |
| Operational Amplifiers | 2 on-chip |
| High-Speed Comparators | 2 |
| Programmable Ramp Generator (PRG) | Yes |
| Zero-Cross Detect (ZCD) | Yes |
| PWM | 10/16-bit, complementary outputs with dead-band |
| Peripheral Pin Select (PPS) | Yes |
| Serial Interfaces | SPI, I²C, EUSART |
| XLP™ nanoWatt Sleep Current | Low (nanowatt class) |
| Temperatura de operação | -40 °C to +85 °C (Industrial) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do PIC16LF1776T-I/SO
| Pino 1 | RA2/AN2/DAC1OUT/OPA1OUT/SEG7/COM0 — Bidirectional I/O with analog, DAC, op-amp and LCD functions |
| Pino 2 | RA3/AN3/DAC1REF+/OPA1IN-/VREF+/SEG15/COM1 — Bidirectional I/O and positive DAC/op-amp reference |
| Pino 3 | RA4/OPA1IN+/T0CKI/CCP4/COM2 — Bidirectional I/O, op-amp non-inverting input, Timer0 clock |
| Pino 4 | RA5/OPA2IN+/AN4/DAC2OUT/CCP3/COM3 — Bidirectional I/O, op-amp 2 input, DAC2 output |
| Pino 5 | Vss — Ground reference |
| Pino 6 | RA7/OSC1/CLKIN — External oscillator input / general I/O |
| Pino 7 | RA6/OSC2/CLKOUT — External oscillator output / general I/O |
| Pino 8 | RC0/SOSCO/T1CKI/PWMIN — Bidirectional I/O, secondary oscillator, Timer1 clock, PWM input |
| Pino 9 | RC1/SOSCI/CCP2 — Bidirectional I/O, secondary oscillator, Capture/Compare/PWM |
| Pino 10 | RC2/CCP1 — Bidirectional I/O, Capture/Compare/PWM 1 |
| Pino 11 | RC3/SCL/SCK — I²C clock or SPI clock / general I/O |
| Pino 12 | RC4/SDA/SDI — I²C data or SPI data input / general I/O |
| Pino 13 | RC5/SDO — SPI data output / general I/O |
| Pino 14 | RC6/TX/CK/AN8 — EUSART TX or clock, analog input |
| Pino 15 | RC7/RX/DT/AN9 — EUSART RX or data, analog input |
| Pino 16 | Vdd — Positive supply (1.8V-3.6V) |
| Pino 17 | RB7/ICSPDAT/AN7 — Programming data, analog input |
| Pino 18 | RB6/ICSPCLK — Programming clock |
| Pino 19 | RB5/AN11/DAC3OUT/CCP5 — Analog input, DAC3 output, PWM5 |
| Pino 20 | RB4/AN10/DAC4OUT — Analog input, DAC4 output |
| Pino 21 | RB3/AN9/CCP2 — Analog input, Capture/Compare/PWM 2 |
| Pino 22 | RB2/AN8/PWMIN/FLT0 — Analog input, PWM fault input |
| Pino 23 | RB1/AN7/HLVDIN/C1IN3-/C2IN3- — Analog input, comparator input |
| Pino 24 | RB0/AN6/FLT0/INT — Analog input, PWM fault, external interrupt |
| Pino 25 | RA0/AN0/DAC1OUT/SEG0/COM4 — Analog input, DAC, LCD segment |
| Pino 26 | RA1/AN1/DAC1REF-/OPA1OUT/SEG1/COM5 — Analog input, DAC negative reference, op-amp output |
| Pino 27 | Vcap — Filter capacitor for internal voltage regulator |
| Pino 28 | Vss — Ground reference |
Aplicações típicas
PIC16LF1776T-I/SO é adequado para 6 aplicaçãos: High-Performance LED Lighting Drivers, Digital Switched-Mode Power Supplies (SMPS), Battery Charging and Battery Management Systems, BLDC and Brushed-DC Motor Control, Sensor Signal Conditioning and Industrial Sensing, Consumer Appliance and White Goods Control.
High-Performance LED Lighting Drivers
The PIC16LF1776T-I/SO is ideal for high-performance LED lighting drivers thanks to its 10/16-bit complementary PWMs, programmable ramp generator (PRG), zero-cross detect (ZCD), four 10-bit DACs and 100 mA capable I/Os in a single 28-SOIC package. Designers can implement smooth analog-style dimming, color-mixing across multiple LED strings and flicker-free high-frequency PWM using the on-chip 16-bit PWM at 32 MHz, achieving >1 MHz PWM resolution. The 4 DACs let multiple LED strings be driven with independent analog currents while the complementary outputs deliver on-board half-bridge timing for boost or buck topologies. XLP™ nanowatt sleep current extends battery life in mains-off standby. Unlike an external LED-driver IC, the PIC16LF1776T-I/SO adds an 8-bit CPU to run custom color algorithms, networked lighting protocols, or fault diagnostics without a second MCU.
Recomendado
Digital Switched-Mode Power Supplies (SMPS)
The PIC16LF1776T-I/SO excels in digital SMPS and PFC applications because its high-speed comparators feed directly into the programmable ramp generator for peak-current-mode and average-current-mode control without external glue logic. Its 10/16-bit complementary PWMs with programmable dead-band directly control synchronous half-bridge FET timing, while the four 10-bit DACs set reference voltages for voltage-mode and current-mode loops. The 32 MHz core executes compensation math with deterministic interrupt latency, supporting switching frequencies above 250 kHz. The 1.8-3.6 V wide-Vdd "LF" variant runs directly from auxiliary bias rails of offline converters, simplifying start-up sequencing. Compared with a pure analog controller, the PIC16LF1776T-I/SO enables adaptive dead-time, soft-start profiling, and telemetry via EUSART or I²C without firmware overhead.
Recomendado
Battery Charging and Battery Management Systems
The PIC16LF1776T-I/SO is well matched to single-cell and multi-cell battery charging and battery management designs because its XLP™ nanowatt technology keeps quiescent current in the nanoamp class during sleep, preserving charge in always-on battery packs. Two on-chip op-amps sense charge/discharge current with low-offset, two high-speed comparators detect end-of-charge and over-current events, and four 10-bit DACs set programmable charge-voltage and charge-current references. The wide 1.8-3.6 V Vdd runs directly from a single Li-ion/LiFePO4 cell. Complementary 16-bit PWMs drive synchronous buck/boost chargers with precise dead-band, eliminating shoot-through. PPS allows flexible pin routing for safety-critical signals. Compared with discrete battery management ICs, the PIC16LF1776T-I/SO adds a full 8-bit CPU for state-of-charge algorithms and SMBus/EUSART telemetry.
Recomendado
BLDC and Brushed-DC Motor Control
The PIC16LF1776T-I/SO is a strong fit for small BLDC and brushed-DC motor control boards because its 10/16-bit complementary PWMs with programmable dead-band directly drive half-bridges or full H-bridges for 1-2 phase stepper, brushed-DC and BLDC motors. The high-speed comparators handle back-EMF zero-cross sensing for sensorless BLDC commutation, and the four 10-bit DACs set torque/speed reference profiles. PRG provides hardware slope compensation for current loops at low PWM duty cycles, and ZCD simplifies AC-line-synchronized timing. With 32 MHz core speed and 8 MIPS throughput, real-time FOC and trapezoidal commutation both fit inside the 14 KB Flash. PPS lets the designer reassign PWM phases for optimal PCB routing. Compared with a dedicated motor-control IC, this part adds full programmability for custom motion profiles.
Recomendado
Sensor Signal Conditioning and Industrial Sensing
The PIC16LF1776T-I/SO is ideal for industrial sensor signal conditioning because its two on-chip op-amps, two high-speed comparators, four 10-bit DACs and 10/16-bit ADC sampling combine into a complete analog front-end on a single die. Designers can amplify a thermocouple or strain-gauge signal, drive a Wheatstone-bridge excitation reference from a DAC, and digitize the result at 32 MIPS — without external analog ICs. PPS eases routing of mixed analog and digital signals, while 100 mA I/Os can directly switch relays or 4-20 mA loops. The 1.8-3.6 V wide Vdd runs from 24 V industrial loops through a small LDO. Compared with a standalone op-amp + ADC chain, the PIC16LF1776T-I/SO integrates calibration, linearization, and HART/EUSART comms in one chip.
Recomendado
Consumer Appliance and White Goods Control
The PIC16LF1776T-I/SO suits washing machines, refrigerators, induction cooktops, coffee machines and small kitchen appliances because it integrates brushed/BLDC motor control, LED display driving and user-interface handling in one 28-SOIC IC. Its complementary PWMs handle motor or induction-heating inverter switching, the four 10-bit DACs set analog references for temperature and power, and the high-speed comparators perform zero-cross detection on the AC mains for synchronous TRIAC driving. The on-chip EUSART and I²C connect to displays, keypads, and wireless modules. Wide 1.8-3.6 V Vdd tolerates noisy rectified mains rails after a small regulator. Compared with multi-chip solutions, the PIC16LF1776T-I/SO lowers BOM cost and PCB area while keeping full firmware flexibility.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16LF1776T-I/SO — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16LF1776-I/SO | PIC16F1776-I/SO | PIC16LF1777-I/SO | PIC16LF1778-I/SO |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 28-SOIC | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same | 28-SOIC - same |
| Program Memory (Flash) | 14 KB | 14 KB | 14 KB | 28 KB | 56 KB |
| RAM | 1 KB | 1 KB | 1 KB | 2 KB | 4 KB |
| Operating Voltage (Vdd) | 1.8 V to 3.6 V | 1.8 V to 3.6 V | 2.3 V to 5.5 V | 1.8 V to 3.6 V | 1.8 V to 3.6 V |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| 10-bit DAC Channels | 4 | 4 | 4 | 4 | 4 |
| On-chip Op-Amps | 2 | 2 | 2 | 2 | 2 |
| Programmable Ramp Generator | Yes | Yes | Yes | Yes | Yes |
| XLP™ Sleep Current | Nanowatt class | Nanowatt class | Standard LP (higher than LF) | Nanowatt class | Nanowatt class |
Principais diferenciais
- Highest level of analog integration in the PIC16F family (vs PIC16LF1769-I/ML)
- 16-bit PWM with complementary outputs and dead-band (vs PIC16F1776-I/SO (5V variant))
- 1.8-3.6 V Vdd + nanowatt XLP™ sleep (vs PIC16LF1778-I/SO (28 KB Flash))
Notas de projeto
Estimated: at Vdd=3.3 V and 32 MHz active, typical IDD for the PIC16LF1776 core is around 4 mA (≈0.13 mA/MHz). Place a 100 nF decoupling capacitor as close as possible to the Vdd pin (pin 16) and a 10 µF bulk cap on the same rail. Add a 1 µF cap on the Vcap pin (pin 27) to stabilize the internal core voltage regulator — omitting this capacitor is a common cause of erratic resets.
Use Peripheral Pin Select (PPS) to remap digital peripherals (CCP, SPI, I²C, EUSART) to almost any digital I/O. This greatly simplifies PCB routing — you can route the SPI bus to one side of the SOIC and remap the UART to another side without swapping the MCU. Refer to the PPS input/output selection tables in the device datasheet, and remember PPS must be unlocked via the PPSLOCK register sequence on every reset.
The two op-amps, four DACs and high-speed comparators share analog pins with digital I/O. Configuring a pin as a digital output while the analog peripheral is enabled can create contention and corrupt the analog reading — always configure the analog function first, then disable the digital input on that pin (ANSELx register). Also, the PRG requires a slope-compensation input pin; miswiring this leads to subharmonic oscillation in peak-current-mode supplies.
The 28-SOIC package has a moderate θJA of roughly 80-90 °C/W on a standard 2-layer JEDEC test board. Estimated: at maximum Vdd (3.6 V), 32 MHz active and full peripheral activity, power dissipation stays well below 100 mW, so no heatsink is required. However, in a sealed industrial enclosure at 85 °C ambient, derate current on the 100 mA I/O banks to avoid exceeding the silicon junction limit.
Informações de conformidade
RoHS and REACH compliance stated by Microchip. Industrial -I temperature grade only (no AEC-Q100 automotive variant of PIC16LF1776 exists in 28-SOIC; automotive users should consult the PIC16F1776 Q-grade equivalents).
