PIC18LF6680-I/L - 64KB Flash, 40MHz 8-bit MCU, 68-PLCC | Microchip
N.º da peça: PIC18LF6680-I/L ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.09 | $7,09 |
| 10 | $6.52 | $65,20 |
| 100 | $5.95 | $595,00 |
| 500 | $5.37 | $2.685,00 |
| 1.000 | $4.78 | $4.780,00 |
PIC18LF6680-I/L Visão geral
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory, working RAM, and a configurable set of digital and analog peripherals. Within Microchip's taxonomy, the PIC18F sits above the baseline PIC16F and below the 16-bit PIC24/dsPIC families, making it the highest-performance 8-bit core. Its Harvard architecture with separate program and data buses, 16-bit instructions, and an 8-level hardware stack delivers deterministic interrupt latency - a key reason the PIC18 platform remains entrenched in industrial, automotive, and CAN-node designs.
Key features of the PIC18LF6680-I/L include an integrated CAN 2.0B controller with hardware acceptance filtering, a 10-bit Analog-to-Digital Converter (ADC) with up to 12 input channels, multiple USART, SPI, and I²C serial engines, up to five 16-bit timers, and 52 digital I/O lines. The instruction set is backward-compatible with earlier PIC16 devices, simplifying migration from legacy code while adding Multiply, hardware divide, and Direct Addressing modes.
Architecturally, the PIC18LF6680 uses an enhanced Harvard core with a 16-bit instruction word and 8-bit data path, plus a 31-level hardware stack for high-level language support (C18 / XC8). Its Enhanced CAN module offloads the entire CAN 2.0B frame handling - including acceptance masks, filters, and prioritization - from the CPU, freeing cycles for application logic. The Flash program memory supports self-programming and In-Circuit Serial Programming (ICSP), enabling field firmware updates without external boot memory.
Typical applications include CAN-enabled industrial sensor nodes, automotive body and chassis controllers, building-automation gateway modules, HVAC control boards, and CAN-to-UART bridges. The wide operating voltage and industrial temperature range (-40 °C to +85 °C for the -I grade) make it well suited to harsh environments where 3.3 V or 5 V rails are present and CAN bus isolation is required.
When designing with this device, place the ICSP/ICD pins (PGC/PGD, MCLR/VPP) on accessible test points so MPLAB ICD programmers can attach without rework. The CAN TX/RX pins must be paired with a transceiver (e.g., MCP2551 or MCP2561) - the PIC18LF6680 cannot drive a CAN bus directly. Decouple VDD/VSS with 100 nF X7R capacitors placed within 5 mm of every supply pin, and bulk-decouple the AVdd rail to keep ADC noise low.
This page synthesizes distributor stock and pricing snapshots, drop-in same-package alternatives, comparison parameters, and practical design notes not consolidated on any single manufacturer or distributor page.
Alternativas drop-in para PIC18LF6680-I/L — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC18LF6680-I/L (mesmo formato e footprint) — diferindo em Core Architecture, Mounting Type, Operating Temperature, Package, Timers.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC18F6680-I/L
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC18LF6680T-I/L
✅ Drop-In✓ Em estoque
$6.05 / unidade
Ver ficha técnica →PIC18LF6682-I/L
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC18LF6585-I/L
✅ Drop-In✓ Em estoque
$5.1 / unidade
Ver ficha técnica →PIC18LF6680-I/L Classificações máximas e características elétricas
| Product Family | PIC® 18F |
| Core Architecture | 8-bit Enhanced Harvard |
| Core Size | 8-bit |
| Program Memory Type | Flash |
| Program Memory Size | 64 KB (32K x 16) |
| RAM Size | 3,328 bytes |
| EEPROM Size | 1,024 bytes |
| Maximum Clock Speed | 40 MHz |
| Supply Voltage Range | 2.0 V to 5.5 V (LF: 4.2 V to 5.5 V per datasheet front page; wider 2.0-5.5 V supported across family) |
| Temperatura de operação | -40 °C to +85 °C (Industrial, "-I" grade) |
| Digital I/O Pins | 52 |
| ADC | 10-bit, up to 12 channels |
| CAN Module | CAN 2.0B with hardware acceptance filtering |
| Serial Interfaces | USART, SPI, I²C |
| Timers | Multiple 16-bit Timer modules (TMR0-TMR5 family) |
| Encapsulamento | 68-pin PLCC (J-lead), 24.23 x 24.23 mm |
| Tipo de montagem | Through-Hole / Socket |
| Nível MSL | 1 (per JEDEC J-STD-020) |
| Lead-Free / RoHS | Lead-free, RoHS compliant |
| ICSP / ICD | Yes (In-Circuit Serial Programming) |
Configuração de pinos do PIC18LF6680-I/L
| Pino 1 | MCLR/VPP — Master Clear / ICSP programming voltage input |
| Pino 2 | RA0/AN0 — PORTA bit 0 / ADC input 0 |
| Pino 3 | RA1/AN1 — PORTA bit 1 / ADC input 1 |
| Pino 4 | RA2/AN2/VREF- — PORTA bit 2 / ADC input 2 / ADC negative reference |
| Pino 5 | RA3/AN3/VREF+ — PORTA bit 3 / ADC input 3 / ADC positive reference |
| Pino 6 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pino 7 | RA5/AN4 — PORTA bit 5 / ADC input 4 |
| Pino 8 | RE0/RD — PORTE bit 0 / read control for PSP |
| Pino 9 | RE1/WR — PORTE bit 1 / write control for PSP |
| Pino 10 | RE2/CS — PORTE bit 2 / chip select for PSP |
| Pino 11 | VDD — Positive supply voltage |
| Pino 12 | VSS — Ground reference |
| Pino 13 | OSC1/CLKI — Crystal oscillator input / external clock input |
| Pino 14 | OSC2/CLKO — Crystal oscillator output / clock output |
| Pino 15 | RC0/T1OSO — PORTC bit 0 / Timer1 oscillator output |
| Pino 16 | RC1/T1OSI — PORTC bit 1 / Timer1 oscillator input |
| Pino 17 | RC2/CCP1 — PORTC bit 2 / Capture/Compare/PWM 1 |
| Pino 18 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I²C clock |
| Pino 19 | RD0/PSP0 — PORTD bit 0 / Parallel Slave Port bit 0 |
| Pino 20 | RD1/PSP1 — PORTD bit 1 / Parallel Slave Port bit 1 |
| Pino 21 | RD2/PSP2 — PORTD bit 2 / Parallel Slave Port bit 2 |
| Pino 22 | RD3/PSP3 — PORTD bit 3 / Parallel Slave Port bit 3 |
| Pino 23 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I²C data |
| Pino 24 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pino 25 | RC6/TX/CK — PORTC bit 6 / USART TX / USART clock |
| Pino 26 | RC7/RX/DT — PORTC bit 7 / USART RX / USART data |
| Pino 27 | RD4/PSP4 — PORTD bit 4 / Parallel Slave Port bit 4 |
| Pino 28 | RD5/PSP5 — PORTD bit 5 / Parallel Slave Port bit 5 |
| Pino 29 | RD6/PSP6 — PORTD bit 6 / Parallel Slave Port bit 6 |
| Pino 30 | RD7/PSP7 — PORTD bit 7 / Parallel Slave Port bit 7 |
| Pino 31 | VSS — Ground reference |
| Pino 32 | VDD — Positive supply voltage |
| Pino 33 | RB0/INT0 — PORTB bit 0 / External interrupt 0 |
| Pino 34 | RB1/INT1 — PORTB bit 1 / External interrupt 1 |
| Pino 35 | RB2/INT2 — PORTB bit 2 / External interrupt 2 |
| Pino 36 | RB3/INT3 — PORTB bit 3 / External interrupt 3 |
| Pino 37 | RB4 — PORTB bit 4 |
| Pino 38 | RB5 — PORTB bit 5 |
| Pino 39 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pino 40 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pino 41 | NC — Not connected (no internal bond) |
| Pino 42 | NC — Not connected (no internal bond) |
| Pino 43 | NC — Not connected (no internal bond) |
| Pino 44 | NC — Not connected (no internal bond) |
| Pino 45 | NC — Not connected (no internal bond) |
| Pino 46 | NC — Not connected (no internal bond) |
| Pino 47 | NC — Not connected (no internal bond) |
| Pino 48 | NC — Not connected (no internal bond) |
| Pino 49 | RA6 — PORTA bit 6 |
| Pino 50 | RA7 — PORTA bit 7 |
| Pino 51 | RF0 — PORTF bit 0 (analog input) |
| Pino 52 | RF1 — PORTF bit 1 (analog input) |
| Pino 53 | RF2 — PORTF bit 2 (analog input) |
| Pino 54 | RF3 — PORTF bit 3 (analog input) |
| Pino 55 | RF4 — PORTF bit 4 (analog input) |
| Pino 56 | RF5 — PORTF bit 5 (analog input) |
| Pino 57 | RF6 — PORTF bit 6 (analog input) |
| Pino 58 | RF7 — PORTF bit 7 (analog input) |
| Pino 59 | CANTX — ECAN transmit output (to external transceiver) |
| Pino 60 | CANRX — ECAN receive input (from external transceiver) |
| Pino 61 | RG0 — PORTG bit 0 |
| Pino 62 | RG1 — PORTG bit 1 |
| Pino 63 | RG2 — PORTG bit 2 |
| Pino 64 | RG3 — PORTG bit 3 |
| Pino 65 | RG4 — PORTG bit 4 |
| Pino 66 | RG5 — PORTG bit 5 |
| Pino 67 | AVDD — Analog positive supply voltage |
| Pino 68 | AVSS — Analog ground reference |
Aplicações típicas
PIC18LF6680-I/L é adequado para 6 aplicaçãos: CAN-Enabled Industrial Sensor Nodes, Automotive Body and Chassis Controllers, Building Automation Gateway Modules, HVAC Control Boards, CAN-to-UART Protocol Bridges, Industrial CAN-Based Motor Drives.
CAN-Enabled Industrial Sensor Nodes
The PIC18LF6680-I/L is a strong fit for industrial CAN sensor nodes because it integrates a hardware CAN 2.0B controller with acceptance filtering, freeing the 40 MHz CPU from bit-level protocol handling. The wide 2.0 V to 5.5 V supply range supports both 24 V-bus-derived 5 V rails and 3.3 V battery-backed nodes, while the 52 I/O pins let you drive multiple sensors, status LEDs, and a local keypad without external I/O expanders. Pair the on-chip ECAN module with an MCP2551 transceiver and isolate the bus with a digital isolator for robust 1 Mbps CAN-FD-ready nodes. The 10-bit ADC and 12 input channels cover analog sensor digitization directly inside the same chip.
Recomendado
Automotive Body and Chassis Controllers
The PIC18LF6680-I/L suits automotive body controllers - window, mirror, seat, and lighting modules - because its 52 I/O pins handle the high pin count of body-control wiring harnesses, while the integrated ECAN module provides a CAN bus interface to the vehicle network. The industrial -40 °C to +85 °C temperature grade and 2.0 V to 5.5 V operating envelope tolerate cold-crank and load-dump transients when paired with an external voltage regulator. The 64 KB Flash supports self-programming for field firmware updates over CAN, eliminating dealer reflashing trips. Use the CCP/ECCP modules for PWM motor control of seat adjusters and mirror actuators.
Recomendado
Building Automation Gateway Modules
Building-automation gateways aggregate multiple fieldbuses (CAN, RS-485, sensor I/O) into a higher-level network, and the PIC18LF6680-I/L fits that role with its hardware CAN 2.0B controller plus USART for RS-485 links via an external transceiver. The 3,328 bytes of RAM handle Modbus or BACnet message buffers without external memory, and the 10-bit ADC monitors internal voltages and analog sensor inputs. Its 2.0 V to 5.5 V supply range lets the same firmware run on 24 VAC-derived 5 V rails or backup-battery 3.3 V rails. The 16-bit instruction word and 31-level hardware stack simplify porting Modbus stacks written in XC8 C.
Recomendado
HVAC Control Boards
HVAC control boards need a mix of analog inputs (temperature, pressure), digital I/O (relays, triac drivers, fan PWM), and a network interface for thermostats and chiller integration. The PIC18LF6680-I/L provides 12 ADC channels for thermistor and pressure transducer readings, multiple CCP/ECCP modules for PWM fan and triac control, and an ECAN module for talking to a chiller or rooftop unit controller. Its 2.0 V to 5.5 V operating envelope tolerates 24 VAC-derived rails, and the 64 KB Flash stores calibration tables and PID firmware. The 52 I/O pins reduce the need for I/O expanders on multi-zone HVAC boards.
Recomendado
CAN-to-UART Protocol Bridges
The PIC18LF6680-I/L is an efficient CAN-to-UART bridge because its hardware ECAN module handles all 11-bit and 29-bit CAN arbitration autonomously, while the dedicated USART engine independently streams the serial side at up to several hundred kbps. The 64 KB Flash supports a full bridging application plus diagnostic logging, and 3,328 bytes of RAM is sufficient to buffer full CAN frames during UART backpressure. Industrial temperature grading and 2.0 V to 5.5 V operation let the bridge sit inline on either bus side. The PIC18 core's deterministic interrupt response ensures no CAN frame is dropped under heavy UART load.
Recomendado
Industrial CAN-Based Motor Drives
The PIC18LF6680-I/L drives small CAN-controlled motor stages by combining its hardware ECAN module with multiple 16-bit CCP/ECCP channels for PWM generation up to 40 MHz timebase resolution. The 52 I/O pins interface to Hall sensors, encoders, brake relays, and fault lines, while the 12-channel 10-bit ADC monitors motor current and bus voltage. The 64 KB Flash stores sensorless BLDC or FOC commutation tables, and 3,328 bytes of RAM keeps a running torque/velocity estimator. Industrial -40 °C to +85 °C operation lets the same firmware deploy in factory-floor servo nodes without derating.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC18LF6680-I/L — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC18F6680-I/L | PIC18LF6680T-I/L | PIC18LF6682-I/L | PIC18LF6585-I/L |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-PLCC | 68-PLCC - same | 68-PLCC - same | 68-PLCC - same | 68-PLCC - same |
| Program Memory | 64 KB Flash | 64 KB Flash | 64 KB Flash | 64 KB Flash | 48 KB Flash |
| RAM | 3,328 bytes | 3,328 bytes | 3,328 bytes | 3,328 bytes | 3,328 bytes |
| Clock Speed | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Supply Voltage | 2.0 V to 5.5 V | 4.2 V to 5.5 V (F variant) | 2.0 V to 5.5 V | 2.0 V to 5.5 V | 2.0 V to 5.5 V |
| CAN Module | CAN 2.0B (ECAN) | CAN 2.0B (ECAN) | CAN 2.0B (ECAN) | CAN 2.0B (ECAN, enhanced buffers) | CAN 2.0B (ECAN) |
| I/O Pins | 52 | 52 | 52 | 52 | 52 |
Principais diferenciais
- Wide 2.0 V to 5.5 V operating envelope with full-speed 40 MHz performance (vs PIC18F6680-I/L)
- Same 64 KB Flash and 68-PLCC footprint as PIC18F6680 family with low-voltage extension (vs PIC18LF6585-I/L)
- Integrated hardware CAN 2.0B with acceptance masking and dedicated buffers (vs PIC18LF452-I/L)
Notas de projeto
Estimated: Power dissipation at 40 MHz with all peripherals active is roughly 50-70 mA at 5 V (2.5-3.5 W worst case). Decouple every VDD/AVDD pin with a 100 nF X7R ceramic placed within 5 mm of the pin, and add a 10 µF bulk tantalum or ceramic on the main VDD rail. AVSS must be tied to VSS at a single low-impedance star point near the regulator to keep ADC reference noise below 1 LSB. Brown-out reset (BOR) should be enabled in the configuration bits to prevent Flash corruption during supply droops.
The PIC18LF6680 integrates the CAN 2.0B protocol controller but CANNOT drive a physical CAN bus directly - you must pair it with an external transceiver such as MCP2551 or MCP2561. Connect CANTX to the transceiver TXD and CANRX to the transceiver RXD, and add 120 Ω termination resistors at each end of the bus segment. Leaving the bus unterminated causes reflections that corrupt arbitration. The ICSP pins (RB6/PGC, RB7/PGD, MCLR/VPP) must be brought out to a header or test pad so MPLAB ICD programmers can attach without board rework.
Keep the crystal (or external clock) traces short and symmetric to minimize EMI and jitter on OSC1/OSC2. Route the CANTX/CANRX differential pair as a short, length-matched pair to the transceiver with a ground reference plane underneath. The AVdd rail should be filtered with a ferrite bead and a dedicated 10 µF + 100 nF decoupling network so ADC conversions during CAN packet bursts do not couple switching noise into the analog reference. Place the ICSP header on the board edge for production programming access.
Informações de conformidade
RoHS compliant and lead-free per Microchip product page. Industrial -40 °C to +85 °C grade. Not AEC-Q100 qualified - this is the standard industrial/consumer grade; AEC-Q100 variants are separate -PT/-PTVAO part numbers.
