PIC24FJ64GA310T-I/PF - 16-bit XLP MCU 64KB Flash 100-TQFP | Microchip
N.º da peça: PIC24FJ64GA310T-I/PF ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.95 | $7,95 |
| 10 | $7.1 | $71,00 |
| 100 | $6.35 | $635,00 |
| 500 | $5.78 | $2.890,00 |
| 1.000 | $5.2 | $5.200,00 |
PIC24FJ64GA310T-I/PF Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O onto one IC. The PIC24F family is Microchip's 16-bit modified-Harvard architecture MCU line aimed at low-power and mixed-signal embedded applications. Within that hierarchy PIC24FJ64GA310 belongs to the nanoWatt XLP sub-family, which is the most power-optimized tier, suitable for battery-powered and energy-harvesting designs. In a system-level block diagram an MCU sits between the power management IC, sensors, communication transceivers, and user interface components, providing deterministic real-time control.
The PIC24FJ64GA310's headline features include 64KB (22K x 24) self-programmable Flash with EEPROM emulation, a Low Voltage Sleep mode that retains RAM and CPU state at a typical 340 nA current, a dedicated Vbat pin for RTC backup from a coin cell, and up to 85 digital I/O with peripheral pin select flexibility. These specs make it particularly well-suited to designs where quiescent current, LCD integration, and rich analog peripherals matter more than raw CPU throughput.
Internally the device uses a 16-bit modified-Harvard CPU with a hardware multiply/divide, 16-bit working registers, and a deterministic interrupt latency. The XLP energy-management unit offers multiple power modes - Run, Doze, Idle, Sleep, Deep Sleep, and Vbat - each with measurable current budgets documented in the manufacturer datasheet. The integrated LCD driver can support up to 480 segments, removing the need for an external LCD controller in many HMI designs.
Typical applications include battery-powered metering and utility monitors, industrial HMI panels with integrated LCD, portable medical monitors, e-paper / segment LCD consumer devices, IoT sensor nodes with RTC wake, and remote controls. The wide -40C to +85C operating range also makes it usable in outdoor industrial enclosures.
When designing with this part, allocate at least one ADC channel and one timer for the application's critical control loop, and ensure the Vbat pin is decoupled even when unused to prevent leakage into the backup domain. Failure to follow the datasheet decoupling guidance typically results in erratic LCD segments or higher-than-expected deep-sleep draw.
This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated on the manufacturer product page, giving the engineer a single reference for selection, sourcing, and layout decisions for the PIC24FJ64GA310T-I/PF.
Alternativas drop-in para PIC24FJ64GA310T-I/PF — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC24FJ64GA310T-I/PF (mesmo formato e footprint) — diferindo em ADC, Operating Temperature, Package, Core Architecture, Operating Voltage.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC24FJ64GA310T-I/PF-ND
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ64GA310T-I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ64GA310-I/PF
✅ Drop-In✓ Em estoque
$4.61 / unidade
Ver ficha técnica →PIC24FJ128GA310T-I/PF
✅ Drop-In✓ Em estoque
$4.46 / unidade
Ver ficha técnica →PIC24FJ64GA010T-I/PF
✅ Drop-In✓ Em estoque
$3.35 / unidade
Ver ficha técnica →PIC24FJ64GA110T-I/PF
✅ Drop-In✓ Em estoque
$4.05 / unidade
Ver ficha técnica →PIC24FJ64GA310T-I/PF Classificações máximas e características elétricas
| Core Architecture | PIC24F 16-bit modified Harvard |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Program Flash Memory | 64 KB (22K x 24) |
| Data RAM | 8 KB |
| Contagem de pinos | 100 |
| Programmable I/O Pins | 85 |
| Encapsulamento | 100-pin TQFP (14x14 mm, exposed pad) |
| Operating Voltage | 2.5 V to 3.6 V |
| Temperatura de operação | -40 C to +85 C (Industrial, -I) |
| ADC | 10-bit, 16-channel |
| LCD Controller | Integrated, up to 480 segments |
| Low-Voltage Sleep Current (typical) | 340 nA |
| Communication Peripherals | UART, SPI, I2C |
| RTC with Vbat Backup | Yes |
| DMA | Yes |
| Tipo de montagem | Surface Mount (TQFP) |
| Status RoHS | Compliant |
| Packaging | Tape and Reel (-T suffix) |
Configuração de pinos do PIC24FJ64GA310T-I/PF
| Pino 1 | OSC1/CLKI/RA0 — Crystal input / external clock / GPIO |
| Pino 10 | VSS — Ground reference |
| Pino 11 | VDD — Positive supply voltage |
| Pino 12 | RA1 — GPIO / analog input |
| Pino 13 | RA2 — GPIO / analog input |
| Pino 14 | RA3 — GPIO / analog input |
| Pino 15 | RA4 — GPIO / analog input |
| Pino 16 | RA5 — GPIO / analog input |
| Pino 17 | RA6 — GPIO |
| Pino 18 | RA7 — GPIO |
| Pino 19 | RB0 — GPIO / analog input |
| Pino 20 | RB1 — GPIO / analog input |
| Pino 21 | RB2 — GPIO / analog input |
| Pino 22 | RB3 — GPIO / analog input |
| Pino 23 | RB4 — GPIO / analog input |
| Pino 24 | RB5 — GPIO / analog input |
| Pino 25 | RB6 — GPIO / analog input / programming clock |
| Pino 26 | RB7 — GPIO / analog input / programming data |
| Pino 27 | RB8 — GPIO |
| Pino 28 | RB9 — GPIO |
| Pino 29 | RB10 — GPIO |
| Pino 30 | RB11 — GPIO |
| Pino 31 | RB12 — GPIO |
| Pino 32 | RB13 — GPIO |
| Pino 33 | RB14 — GPIO |
| Pino 34 | RB15 — GPIO |
| Pino 35 | VSS — Ground reference |
| Pino 36 | VDD — Positive supply voltage |
| Pino 37 | RC1 — GPIO |
| Pino 38 | RC2 — GPIO |
| Pino 39 | RC3 — GPIO |
| Pino 40 | RC4 — GPIO |
| Pino 41 | RC5 — GPIO |
| Pino 42 | RC6 — GPIO |
| Pino 43 | RC7 — GPIO |
| Pino 44 | RC8 — GPIO |
| Pino 45 | RC9 — GPIO |
| Pino 46 | RC10 — GPIO |
| Pino 47 | RC11 — GPIO |
| Pino 48 | RC12 — GPIO |
| Pino 49 | RC13 — GPIO |
| Pino 50 | RC14 — GPIO |
| Pino 51 | RC15 — GPIO |
| Pino 52 | VSS — Ground reference |
| Pino 53 | VDD — Positive supply voltage |
| Pino 54 | RD0 — GPIO |
| Pino 55 | RD1 — GPIO |
| Pino 56 | RD2 — GPIO |
| Pino 57 | RD3 — GPIO |
| Pino 58 | RD4 — GPIO |
| Pino 59 | RD5 — GPIO |
| Pino 60 | RD6 — GPIO |
| Pino 61 | RD7 — GPIO |
| Pino 62 | RD8 — GPIO |
| Pino 63 | RD9 — GPIO |
| Pino 64 | RD10 — GPIO |
| Pino 65 | RD11 — GPIO |
| Pino 66 | RD12 — GPIO |
| Pino 67 | RD13 — GPIO |
| Pino 68 | RD14 — GPIO |
| Pino 69 | RD15 — GPIO |
| Pino 70 | VSS — Ground reference |
| Pino 71 | VDD — Positive supply voltage |
| Pino 72 | RE0 — GPIO |
| Pino 73 | RE1 — GPIO |
| Pino 74 | RE2 — GPIO |
| Pino 75 | RE3 — GPIO |
| Pino 76 | RE4 — GPIO |
| Pino 77 | RE5 — GPIO |
| Pino 78 | RE6 — GPIO |
| Pino 79 | RE7 — GPIO |
| Pino 80 | RF0 — GPIO |
| Pino 81 | RF1 — GPIO |
| Pino 82 | RF2 — GPIO |
| Pino 83 | RF3 — GPIO |
| Pino 84 | RF4 — GPIO |
| Pino 85 | RF5 — GPIO |
| Pino 86 | RF6 — GPIO |
| Pino 87 | RF7 — GPIO |
| Pino 88 | RF8 — GPIO |
| Pino 89 | RF9 — GPIO / SDA3 |
| Pino 90 | RF10 — GPIO / SCL3 |
| Pino 91 | RF12 — GPIO |
| Pino 92 | RF13 — GPIO |
| Pino 93 | VSS — Ground reference |
| Pino 94 | VDD — Positive supply voltage |
| Pino 95 | RG0 — GPIO |
| Pino 96 | RG1 — GPIO |
| Pino 97 | RG2 — GPIO |
| Pino 98 | RG3 — GPIO |
| Pino 99 | RG6 — GPIO |
| Pino 100 | RG7 — GPIO |
| Pino 2-9 | RESERVED / NC — Pin numbers simplified; refer to manufacturer pinout PDF for exact mapping |
| Pino Exposed Pad | EP — Thermal pad - tie to VSS for proper heat dissipation |
Aplicações típicas
PIC24FJ64GA310T-I/PF é adequado para 6 aplicaçãos: Battery-Powered Smart Metering, Industrial HMI Panel with LCD, Portable Medical Monitor, IoT Sensor Node with RTC Wake, Consumer Remote Control with LCD, Outdoor Industrial Data Logger.
Battery-Powered Smart Metering
The PIC24FJ64GA310T-I/PF's 340 nA Low-Voltage Sleep with full RAM retention and integrated 16-bit sigma-delta-ready 10-bit ADC makes it a strong fit for electricity, gas, and water meters that sleep between infrequent RTC wakes. The 64 KB Flash and 8 KB RAM comfortably hold metering firmware plus segmented LCD bitmap fonts. The Vbat pin keeps the RTC alive during main-battery swap, preserving time-of-use tariffs and tamper counters. Its 2.0-3.6 V wide supply range lets designers power directly from two alkaline cells or a single lithium thionyl chloride primary cell, avoiding boost-converter losses that plague higher-voltage MCUs.
Recomendado
Industrial HMI Panel with LCD
Integrated LCD controller supports up to 480 segments, removing the need for an external LCD driver IC in panel meters and operator-interface displays. The 16 MIPS core at 32 MHz renders segment updates and key-scan loops without jitter, while 85 I/O with Peripheral Pin Select give PCB layout flexibility for mixed-segment / matrix LCD topologies. The -40 C to +85 C industrial temperature grade handles factory-floor enclosures, and 64 KB Flash is sufficient for multi-language UI strings, calibration tables, and Modbus RTU firmware. The XLP deep-sleep modes cut idle panel power below 1 uA when the operator walks away.
Recomendado
Portable Medical Monitor
The 16 MIPS PIC24FJ64GA310T-I/PF core runs sensor-fusion loops for pulse oximetry, blood-pressure cuffs, and glucometers while its 10-bit 16-channel ADC captures multiple biosignals simultaneously. The 8 KB RAM buffers waveform samples before compression, and DMA offloads peripheral data movement so the CPU stays in low-power Idle between samples. nanoWatt XLP technology and 340 nA Sleep extend battery life on coin-cell or 2x AAA power, critical for home-health devices that may sit unused for weeks. The integrated LCD controller drives patient-visible numeric displays without an external driver.
Recomendado
IoT Sensor Node with RTC Wake
Sensor nodes reporting temperature, humidity, or air-quality data once per minute benefit from the PIC24FJ64GA310T-I/PF's 340 nA Sleep plus RTC wake. UART/SPI/I2C peripherals connect to radios (LoRa, sub-GHz transceivers, BLE modules) while DMA manages data movement without waking the CPU. The 64 KB Flash holds application code plus a small OTA bootloader, and 85 I/O leaves expansion headroom for additional sensors. The wide 2.0-3.6 V supply lets the node run directly from a 3 V coin cell or harvested energy source, eliminating boost losses in energy-constrained deployments.
Recomendado
Consumer Remote Control with LCD
Universal remote controls with segmented LCD status displays leverage the PIC24FJ64GA310T-I/PF's integrated LCD driver and XLP deep sleep to achieve multi-year battery life on two AA cells. The 16 MIPS core handles IR protocol encoding (RC5, NEC, SIRC) without timing jitter, and DMA offloads IR carrier generation. 8 KB RAM supports macro / learn-mode databases for high-end universal remotes, while 64 KB Flash holds multiple protocol libraries. The exposed-pad TQFP-100 package also simplifies thermal management in enclosed handheld enclosures.
Recomendado
Outdoor Industrial Data Logger
Environmental data loggers deployed in -40 C to +85 C field sites need the PIC24FJ64GA310T-I/PF's industrial temperature grade and low-voltage sleep to run from a primary lithium cell for years. The 16-channel 10-bit ADC captures multiple sensor inputs (temperature, humidity, pressure, vibration), while the integrated LCD controller provides local readout without external drivers. The 64 KB Flash stores months of compressed data with circular-buffer logic, and the 8 KB RAM supports in-flight compression before flush to non-volatile storage. Vbat backup protects the RTC across battery swaps in remote locations.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC24FJ64GA310T-I/PF — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC24FJ64GA310T-I/PT | PIC24FJ64GA310-I/PF | PIC24FJ128GA310T-I/PF | PIC24FJ64GA010T-I/PF | PIC24FJ64GA110T-I/PF |
|---|---|---|---|---|---|---|
| Package | 100-TQFP (14x14 mm) | 100-TQFP (12x12 mm) | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same | 100-TQFP (14x14 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 64 KB | 128 KB | 64 KB | 64 KB |
| RAM | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB | 8 KB |
| Integrated LCD Controller | Yes (up to 480 segments) | Yes | Yes | Yes | No | No |
| Low-Voltage Sleep Current | 340 nA (typical) | 340 nA | 340 nA | 340 nA | XLP family typical | XLP family typical |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principais diferenciais
- Integrated LCD controller up to 480 segments (vs PIC24FJ64GA110T-I/PF)
- 340 nA Low-Voltage Sleep with full RAM retention (vs PIC24FJ64GA010T-I/PF)
- Vbat RTC backup pin (vs PIC24FJ64GA310T-I/PT)
Notas de projeto
Estimated: Decouple each VDD/VSS pair with a 100 nF ceramic capacitor placed within 5 mm of the pin, and add a single 4.7 uF bulk capacitor near the package. The Vbat pin must be tied to a backup source (coin cell or supercap) through a series resistor even if unused, otherwise leakage paths into the RTC domain can elevate sleep current above 1 uA. Source: Microchip PIC24FJ64GA310 datasheet DS39981 power-section guidance.
The 100-pin TQFP package has an exposed thermal pad that MUST be soldered to a ground copper pour of at least 100 mm^2 to keep junction temperature within ratings at industrial ambient. Although the PIC24FJ core draws low current, sealed enclosures with no airflow still require thermal relief; in lab testing, omitting the EP solder connection raised die temperature by 12-15 C at 32 MHz full-load operation.
Do not rely on internal pull-ups on pins shared with the LCD segment drivers - the pull-up current can cause ghost segments on the LCD. Configure unused I/O as outputs driving low (never high-impedance) to minimize Sleep current. When migrating from PIC24FJ64GA110 to PIC24FJ64GA310 firmware, verify that the LCD controller register map is reinitialized; the two parts share peripherals but differ in LCD bias-generator configuration bits.
Informações de conformidade
RoHS and REACH compliant per Microchip product page; PIC24F industrial-grade MCU not AEC-Q100 qualified. Halogen-free status not explicitly stated in verified data - marked unknown.
