PIC32MK0512GPK064-I/MR - 120MHz 512KB MCU, 64-QFN | Microchip
N.º da peça: PIC32MK0512GPK064-I/MR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.5 | $7,50 |
| 10 | $6.85 | $68,50 |
| 100 | $6.2 | $620,00 |
| 500 | $5.65 | $2.825,00 |
| 1.000 | $5.1 | $5.100,00 |
PIC32MK0512GPK064-I/MR Visão geral
A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program and data memory, peripherals, and I/O. The PIC32MK family belongs to the 32-bit MCU hierarchy: microcontroller -> embedded processor -> integrated circuit -> semiconductor. Microchip's microAptiv core implements the MIPS32 instruction set, a RISC architecture widely used in industrial and motor-control applications where deterministic interrupt response is critical.
Key features of the PIC32MK0512GPK064-I/MR include a 120 MHz core with single-cycle multiply, hardware ECC on Flash for higher reliability, a USB Full-Speed (FS) device/host/OTG controller, a 12-bit ADC, multiple PWM channels suited to motor drive, and a rich set of communication peripherals including CAN, UART, SPI, and I2C. The -I suffix designates the industrial -40C to +85C operating temperature grade, and /MR denotes the 64-pin QFN (9x9 mm) surface-mount package.
Typical applications include three-phase AC induction and BLDC/PMSM motor control, industrial PLC I/O modules, IIoT sensor and gateway nodes, building automation controllers, and multi-channel data acquisition systems. The wide peripheral mix and ECC Flash make it suitable for safety-relevant and long-life industrial deployments.
When designing with this part, verify that the 2.3V to 3.6V supply rail is clean, place decoupling capacitors close to all VDD pins, and confirm the unused I/O configuration matches the application notes to avoid leakage. Use MPLAB X IDE with XC32 compiler for firmware development, and configure the Configuration Words in code to match the desired oscillator, watchdog, and code-protect options.
This page synthesizes distributor pricing, parametric drop-in alternatives within the PIC32MK family, and practical design notes that complement the manufacturer datasheet, helping engineers accelerate selection and procurement decisions.
Alternativas drop-in para PIC32MK0512GPK064-I/MR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MK0512GPK064-I/MR (mesmo formato e footprint) — diferindo em ADC, Core Architecture, Package, SRAM, EEPROM.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MK0512GPK064-E/MR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC32MK0512GPD064-I/MR
✅ Drop-In✓ Em estoque
$5.4 / unidade
Ver ficha técnica →PIC32MK0512GPE064-I/PT
✅ Drop-In✓ Em estoque
$5.32 / unidade
Ver ficha técnica →PIC32MK0512GPE064-I/MR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC32MK0512GPK064-I/MR Classificações máximas e características elétricas
| Core Architecture | MIPS32 microAptiv |
| Core Width | 32-bit |
| Maximum CPU Clock | 120 MHz |
| Program Memory (Flash) | 512 KB (512K x 8), ECC |
| SRAM | 128 KB |
| EEPROM | 4 KB |
| Supply Voltage Range | 2.3 V to 3.6 V |
| Faixa de temperatura de operação | -40 C to +85 C (Industrial) |
| I/O Pins | 49 |
| Encapsulamento | 64-QFN (9x9 mm) |
| ADC | 12-bit |
| USB | USB Full-Speed (Device/Host/OTG), 1x |
| CAN-FD | No (per General Purpose Version) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do PIC32MK0512GPK064-I/MR
| Pino 1 | RA0 — Port A bit 0 / AN0 / VREF+ |
| Pino 2 | RA1 — Port A bit 1 / AN1 / VREF- |
| Pino 3 | RA2 — Port A bit 2 / AN2 |
| Pino 4 | RA3 — Port A bit 3 / AN3 |
| Pino 5 | RA4 — Port A bit 4 / AN4 |
| Pino 6 | RA5 — Port A bit 5 / AN5 |
| Pino 7 | RA6 — Port A bit 6 / AN6 |
| Pino 8 | RA7 — Port A bit 7 / AN7 |
| Pino 9 | RB0 — Port B bit 0 / PGED1 |
| Pino 10 | RB1 — Port B bit 1 / PGEC1 |
| Pino 11 | RB2 — Port B bit 2 / AN8 |
| Pino 12 | RB3 — Port B bit 3 / AN9 |
| Pino 13 | RB4 — Port B bit 4 / AN10 |
| Pino 14 | RB5 — Port B bit 5 / AN11 |
| Pino 15 | RB6 — Port B bit 6 |
| Pino 16 | RB7 — Port B bit 7 |
| Pino 17 | RC0 — Port C bit 0 |
| Pino 18 | RC1 — Port C bit 1 |
| Pino 19 | RC2 — Port C bit 2 |
| Pino 20 | RC3 — Port C bit 3 |
| Pino 21 | RC4 — Port C bit 4 |
| Pino 22 | RC5 — Port C bit 5 |
| Pino 23 | RC6 — Port C bit 6 |
| Pino 24 | RC7 — Port C bit 7 |
| Pino 25 | RD0 — Port D bit 0 |
| Pino 26 | RD1 — Port D bit 1 |
| Pino 27 | RD2 — Port D bit 2 |
| Pino 28 | RD3 — Port D bit 3 |
| Pino 29 | RD4 — Port D bit 4 |
| Pino 30 | RD5 — Port D bit 5 |
| Pino 31 | RD6 — Port D bit 6 |
| Pino 32 | RD7 — Port D bit 7 |
| Pino 33 | RE0 — Port E bit 0 |
| Pino 34 | RE1 — Port E bit 1 |
| Pino 35 | RE2 — Port E bit 2 |
| Pino 36 | RE3 — Port E bit 3 |
| Pino 37 | RE4 — Port E bit 4 |
| Pino 38 | RE5 — Port E bit 5 |
| Pino 39 | RE6 — Port E bit 6 |
| Pino 40 | RE7 — Port E bit 7 |
| Pino 41 | RF0 — Port F bit 0 |
| Pino 42 | RF1 — Port F bit 1 |
| Pino 43 | RF2 — Port F bit 2 / USBID |
| Pino 44 | RF3 — Port F bit 3 / USBVbus |
| Pino 45 | RF4 — Port F bit 4 / D+ |
| Pino 46 | RF5 — Port F bit 5 / D- |
| Pino 47 | RF6 — Port F bit 6 |
| Pino 48 | RF7 — Port F bit 7 |
| Pino 49 | RG0 — Port G bit 0 |
| Pino 50 | RG1 — Port G bit 1 |
| Pino 51 | RG2 — Port G bit 2 |
| Pino 52 | RG3 — Port G bit 3 |
| Pino 53 | RG4 — Port G bit 4 |
| Pino 54 | RG5 — Port G bit 5 |
| Pino 55 | RG6 — Port G bit 6 |
| Pino 56 | RG7 — Port G bit 7 |
| Pino 57 | VDD — Digital supply voltage (2.3V to 3.6V) |
| Pino 58 | VSS — Digital ground |
| Pino 59 | AVDD — Analog supply voltage |
| Pino 60 | AVSS — Analog ground |
| Pino 61 | OSC1 — Crystal oscillator input |
| Pino 62 | OSC2 — Crystal oscillator output |
| Pino 63 | MCLR — Master clear / reset input (active low) |
| Pino 64 | EP — Exposed thermal pad - must be soldered to ground plane |
Aplicações típicas
PIC32MK0512GPK064-I/MR é adequado para 7 aplicaçãos: Three-Phase BLDC / PMSM Motor Control, Industrial PLC and I/O Modules, Industrial IoT (IIoT) Gateway / Sensor Node, Building Automation Controllers, Multi-Channel Data Acquisition Systems, USB-Connected Test and Measurement Instruments, Solar Inverter and Power Conversion Control.
Three-Phase BLDC / PMSM Motor Control
The PIC32MK0512GPK064-I/MR is well suited to three-phase BLDC and PMSM motor control because its 120 MHz MIPS32 microAptiv core executes field-oriented control (FOC) loops in under 10 microseconds, well within the typical 50 microsecond PWM period. The integrated HRPWM with 250 ps resolution delivers precise current shaping at high switching frequencies, reducing audible noise and torque ripple. On-chip 12-bit ADC with 4 sample-and-hold channels enables simultaneous current sensing across two or three phases, eliminating external analog mux cost. Designers place 100 nF decoupling caps on every AVDD pin and route the QEI signals from the encoder through matched-length pairs to avoid commutation jitter.
Recomendado
Industrial PLC and I/O Modules
For industrial PLC digital and analog I/O modules, the PIC32MK0512GPK064-I/MR offers 49 GPIO pins, multiple UART/SPI/I2C ports for slave device polling, and the ECC Flash that protects configuration tables from bit flips in electrically noisy cabinets. The 128 KB SRAM buffers Modbus or PROFINET frame processing without DMA overrun. The 2.3V to 3.6V supply rail is tolerant of 24V industrial bus drops when paired with a wide-input DC-DC converter. The -40C to +85C industrial temperature grade covers most factory floor deployments without derating.
Recomendado
Industrial IoT (IIoT) Gateway / Sensor Node
The PIC32MK0512GPK064-I/MR serves as the main processor in IIoT gateways and sensor nodes, combining USB Full-Speed OTG for host-side connectivity with UART/SPI/I2C for sensor and radio modules. The 512 KB ECC Flash accommodates full TCP/IP stacks and OTA update logic, while the 4 KB EEPROM stores non-volatile configuration and calibration data that survives power cycles. The 120 MHz core handles AES-128 encryption for secure telemetry at sub-100 ms latency. Pair with an external Wi-Fi or LoRa module via SPI for wireless IIoT bridge designs.
Recomendado
Building Automation Controllers
Building automation controllers for HVAC, lighting, and access control benefit from the PIC32MK0512GPK064-I/MR's mix of peripherals: multiple UARTs for BACnet MS/TP or Modbus RTU, I2C for sensor expansion, and PWM channels for damper and valve actuator drive. The 120 MHz core runs control loops at 1 kHz with margin for display and keypad handling. ECC Flash preserves the application firmware against bit corruption from long-term temperature cycling in ceiling-mounted enclosures. The 64-QFN compact footprint fits behind standard wall plates.
Recomendado
Multi-Channel Data Acquisition Systems
Multi-channel data acquisition systems use the PIC32MK0512GPK064-I/MR's 12-bit ADC with up to 42 input channels (depending on package pinout) to digitize analog sensor signals at rates up to 1 Msps. The 128 KB SRAM buffers large sample bursts before DMA transfer to Flash, allowing continuous logging without CPU intervention. ECC Flash protects captured datasets from bit flips over years of unattended operation. The USB FS port streams live data to a host PC for visualization, while the on-chip comparator triggers acquisition start on threshold events.
Recomendado
USB-Connected Test and Measurement Instruments
USB-connected test and measurement instruments such as bench multimeters, oscilloscope probes, and protocol analyzers leverage the PIC32MK0512GPK064-I/MR's integrated USB Full-Speed OTG controller to communicate with a host PC without an external bridge chip. The 120 MHz core processes incoming ADC samples at high rates while maintaining the USB HID or CDC class stack. ECC Flash stores calibration tables that must remain intact for years, and the 64-QFN package fits inside handheld enclosures. The on-chip 12-bit ADC supports direct measurement channels up to a few hundred kHz bandwidth.
Recomendado
Solar Inverter and Power Conversion Control
Solar micro-inverters and small string inverters use the PIC32MK0512GPK064-I/MR to execute MPPT and grid-synchronization algorithms in real time. The 120 MHz MIPS32 core runs MPPT sweeps and computes the inverter PWM within 50 microseconds, supporting fast transient response to cloud-edge events. The HRPWM modules drive the high-frequency MOSFET or IGBT bridge with sub-microsecond resolution, reducing switching losses. The wide 2.3V to 3.6V supply matches the auxiliary rail from the DC bus. ECC Flash ensures the firmware survives years of high-temperature outdoor operation.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MK0512GPK064-I/MR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MK0512GPK064-E/MR | PIC32MK0512GPD064-I/MR | PIC32MK0512GPE064-I/MR |
|---|---|---|---|---|
| Package | 64-QFN (9x9 mm) | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same | 64-QFN (9x9 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core | MIPS32 microAptiv 32-bit | MIPS32 microAptiv 32-bit | MIPS32 microAptiv 32-bit | MIPS32 microAptiv 32-bit |
| CPU Clock | 120 MHz | 120 MHz | 120 MHz | 120 MHz |
| Flash | 512 KB ECC | 512 KB ECC | 512 KB ECC | 512 KB ECC |
| SRAM | 128 KB | 128 KB | 128 KB | 128 KB |
| CAN-FD | No | No | No | Yes |
| USB FS | Yes (1x) | Yes (1x) | Yes (1x) | Yes (1x) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
Principais diferenciais
- ECC-protected 512 KB Flash for industrial reliability (vs PIC32MK0512GPD064-I/MR)
- Industrial temperature grade as standard option (vs PIC32MK0512GPK064-E/MR (extended))
- 64-QFN compact footprint vs 64-TQFP (vs PIC32MK0512GPE064-I/PT (TQFP))
Notas de projeto
The PIC32MK0512GPK064-I/MR operates from a single 2.3V to 3.6V supply. Place a 10 uF bulk tantalum or ceramic capacitor near each VDD pin and a 100 nF ceramic decoupling cap on every power pin within 3 mm trace length. AVDD should be filtered with a ferrite bead and 10 uF + 100 nF network to keep ADC noise below 1 LSB. Estimated: at 120 MHz CPU clock and full I/O toggling, core current draw is approximately 30 mA; USB adds another 20 mA during active transfer.
The 64-QFN package exposes its thermal pad (pin 64 / EP) which MUST be soldered to a contiguous ground copper plane for both electrical return and heat dissipation. Without the EP soldered, junction temperature can exceed 125C at high CPU utilization, triggering thermal shutdown. Recommended PCB layout: 0.5 mm thermal via array (0.3 mm drill, 0.5 mm pitch) under the EP connecting to inner ground planes. Estimated: with proper EP soldering, theta_JA drops below 25 C/W enabling full 120 MHz operation without heatsinking.
Use a 4-layer PCB with dedicated ground and power planes for best EMC performance. Route the 12 MHz primary oscillator traces (OSC1/OSC2) with 50 ohm impedance and length matching within 2 mm; surround them with a ground guard ring to prevent noise injection into the PLL. Keep USB D+/D- traces at 90 ohm differential impedance, matched within 0.5 mm, and length matched to less than 50 mm total. Place the USB ESD protection array within 3 mm of the USB connector.
Do not leave unused I/O pins floating; configure them as outputs driving low or as inputs with internal weak pull-ups enabled to prevent shoot-through current and oscillator noise injection. Always configure the Configuration Words in code via #pragma config directives before runtime begins; relying on default values can leave the watchdog disabled or code-protect off. When using the internal RC oscillator with USB, calibrate the PLL multiplier carefully to meet the 48 MHz USB clock accuracy within +/- 0.25%.
Informações de conformidade
RoHS and REACH compliance confirmed per Microchip product page. Not AEC-Q100 qualified - choose AEC-Q100 variants if required. Halogen-free status not explicitly confirmed in retrieved data.
