PIC32MX564F128LT-I/PT - 80MHz 32-bit MCU 128KB Flash USB/CAN | Microchip
N.º da peça: PIC32MX564F128LT-I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.45 | $7,45 |
| 10 | $6.71 | $67,10 |
| 100 | $5.95 | $595,00 |
| 500 | $5.32 | $2.660,00 |
| 1.000 | $4.78 | $4.780,00 |
PIC32MX564F128LT-I/PT Visão geral
A 32-bit microcontroller (MCU) is a microprocessor core combined with on-die Flash program memory, SRAM data memory and a peripheral set in a single integrated circuit. PIC32MX5xx parts sit in Microchip's PIC32 family, which targets the MIPS32 M4K architecture - bridging 8/16-bit PIC MCU scalability with 32-bit performance for USB, CAN, graphics and audio bridging applications. The hypernym hierarchy is: PIC32MX564 subfamily -> PIC32MX5xx family -> PIC32 series -> 32-bit MCU -> microcontroller -> integrated circuit -> semiconductor.
Key features include a 32-bit MIPS M4K core with 1.56 DMIPS/MHz, hardware multiply/divide, 128 KB Flash (128K x 8), 32 KB SRAM, 4-channel DMA, full-speed USB 2.0 device/host/OTG, CAN 2.0B active, two I2C, two SPI, two UART, a 16-bit Parallel Master Port (PMP) for graphics/parallel memory and a 10-bit 1 Msps ADC. The 100-pin TQFP exposes 53 digital I/O lines, supporting multiple 5V-tolerant pins, hardware PMP bus and ICSP debugging.
Technical depth: the M4K core executes most instructions in one clock, giving 80 MHz core operation ~80 MIPS sustained throughput, with single-cycle 32-bit multiply and hardware divide. The 4-channel DMA engine offloads peripheral-to-memory and memory-to-memory transfers, freeing the core for control code. The 16-bit PMP enables direct connection to graphical LCDs, parallel SRAM and FPGA slaves. The integrated USB PHY supports low-speed, full-speed and full-speed OTG modes without external transceivers in most configurations.
Typical applications include industrial USB-to-CAN bridges, automotive infotainment subsystems (CAN node controllers), HMI panels with TFT LCDs using the Parallel Master Port, USB device/host bridges (barcode scanners, data loggers), and CAN-based sensor nodes. Designers select this part for code density advantages (one instruction per word vs 8-bit PIC) plus deterministic interrupt latency.
Design considerations: the 100-pin TQFP requires a 4-layer PCB with thermal relief for the 80 MHz switching current; 0.1 uF ceramic decoupling is recommended within 5 mm of every VDD/VSS pair. For USB designs, route D+/D- as a 90 ohm differential pair and place the 48 MHz crystal within 5 mm of the OSC pins.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas drop-in para PIC32MX564F128LT-I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MX564F128LT-I/PT (mesmo formato e footprint) — diferindo em ADC, Operating Temperature, Package, USB, SRAM.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MX564F128HT-I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC32MX564F128HT-V/PT
✅ Drop-In✓ Em estoque
$6.1 / unidade
Ver ficha técnica →PIC32MX564F064LT-I/PT
✅ Drop-In✓ Em estoque
$3.65 / unidade
Ver ficha técnica →PIC32MX564F064L-I/PT
✅ Drop-In✓ Em estoque
$4.85 / unidade
Ver ficha técnica →PIC32MX534F064H-I/PT
✅ Drop-In✓ Em estoque
$3.95 / unidade
Ver ficha técnica →PIC32MX470F512L-I/PT
✅ Drop-In✓ Em estoque
$6.32 / unidade
Ver ficha técnica →PIC32MX564F128LT-I/PT Classificações máximas e características elétricas
| Core Architecture | MIPS32 M4K |
| Core Width | 32-bit |
| Maximum CPU Frequency | 80 MHz |
| Program Memory (Flash) | 128 KB (128K x 8) |
| RAM Size | 32 KB |
| Number of I/O Pins | 53 |
| Encapsulamento / Caixa | 100-TQFP (12x12 mm) |
| Tipo de montagem | Surface Mount |
| Tensão de alimentação | 2.5 V / 3.3 V |
| Temperatura de operação | -40C to +85C (Industrial) |
| USB Interface | USB 2.0 Full-Speed Device/Host/OTG |
| CAN Interface | CAN 2.0B active |
| DMA Channels | 4 |
| ADC | 10-bit 1 Msps |
| Parallel Master Port (PMP) | 16-bit |
| UART / SPI / I2C | 2 / 2 / 2 |
| Status RoHS | Compliant |
| Nível MSL | 3 (168 hours) |
Configuração de pinos do PIC32MX564F128LT-I/PT
| Pino 1 | RG15 — I/O port RG15 / D-/D+ secondary |
| Pino 2 | RG13 — I/O port RG13 |
| Pino 3 | RG12 — I/O port RG12 |
| Pino 4 | RG14 — I/O port RG14 |
| Pino 5 | VDD — Core/digital supply 2.5-3.3V |
| Pino 6 | RD0 — I/O port RD0 |
| Pino 7 | RD1 — I/O port RD1 |
| Pino 8 | RD2 — I/O port RD2 |
| Pino 9 | RD3 — I/O port RD3 |
| Pino 10 | RD4 — I/O port RD4 |
| Pino 11 | RD5 — I/O port RD5 |
| Pino 12 | RD6 — I/O port RD6 |
| Pino 13 | RD7 — I/O port RD7 |
| Pino 14 | RC13 — I/O port RC13 |
| Pino 15 | RC14 — I/O port RC14 |
| Pino 16 | RC12 — I/O port RC12 |
| Pino 17 | RB0 — I/O port RB0 / PGC |
| Pino 18 | RB1 — I/O port RB1 / PGD |
| Pino 19 | RB2 — I/O port RB2 |
| Pino 20 | RB3 — I/O port RB3 |
| Pino 21 | RB4 — I/O port RB4 |
| Pino 22 | RB5 — I/O port RB5 |
| Pino 23 | RB6 — I/O port RB6 |
| Pino 24 | RB7 — I/O port RB7 |
| Pino 25 | RC1 — I/O port RC1 |
| Pino 26 | RC2 — I/O port RC2 |
| Pino 27 | RC3 — I/O port RC3 |
| Pino 28 | RC4 — I/O port RC4 |
| Pino 29 | VSS — Ground |
| Pino 30 | OSC1 — Crystal oscillator input |
| Pino 31 | OSC2 — Crystal oscillator output |
| Pino 32 | VSS — Ground |
| Pino 33 | RA0 — I/O port RA0 |
| Pino 34 | RA1 — I/O port RA1 |
| Pino 35 | RA2 — I/O port RA2 |
| Pino 36 | RA3 — I/O port RA3 |
| Pino 37 | RA4 — I/O port RA4 |
| Pino 38 | RA5 — I/O port RA5 |
| Pino 39 | RA6 — I/O port RA6 |
| Pino 40 | RA7 — I/O port RA7 |
| Pino 41 | RA8 — I/O port RA8 |
| Pino 42 | RA9 — I/O port RA9 |
| Pino 43 | RA10 — I/O port RA10 |
| Pino 44 | VDD — Supply 2.5-3.3V |
| Pino 45 | VSS — Ground |
| Pino 46 | RB8 — I/O port RB8 |
| Pino 47 | RB9 — I/O port RB9 |
| Pino 48 | RB10 — I/O port RB10 |
| Pino 49 | RB11 — I/O port RB11 |
| Pino 50 | RB12 — I/O port RB12 |
| Pino 51 | RB13 — I/O port RB13 |
| Pino 52 | RB14 — I/O port RB14 |
| Pino 53 | RB15 — I/O port RB15 |
| Pino 54 | RC0 — I/O port RC0 |
| Pino 55 | RC5 — I/O port RC5 |
| Pino 56 | RC6 — I/O port RC6 |
| Pino 57 | RC7 — I/O port RC7 |
| Pino 58 | RC8 — I/O port RC8 |
| Pino 59 | RC9 — I/O port RC9 |
| Pino 60 | VDD — Supply 2.5-3.3V |
| Pino 61 | VSS — Ground |
| Pino 62 | RD8 — I/O port RD8 |
| Pino 63 | RD9 — I/O port RD9 |
| Pino 64 | RD10 — I/O port RD10 |
| Pino 65 | RD11 — I/O port RD11 |
| Pino 66 | RD12 — I/O port RD12 |
| Pino 67 | RD13 — I/O port RD13 |
| Pino 68 | RD14 — I/O port RD14 |
| Pino 69 | RD15 — I/O port RD15 |
| Pino 70 | RE0 — I/O port RE0 |
| Pino 71 | RE1 — I/O port RE1 |
| Pino 72 | RE2 — I/O port RE2 |
| Pino 73 | RE3 — I/O port RE3 |
| Pino 74 | RE4 — I/O port RE4 |
| Pino 75 | RE5 — I/O port RE5 |
| Pino 76 | RE6 — I/O port RE6 |
| Pino 77 | RE7 — I/O port RE7 |
| Pino 78 | RF0 — I/O port RF0 |
| Pino 79 | RF1 — I/O port RF1 |
| Pino 80 | VDD — Supply 2.5-3.3V |
| Pino 81 | VSS — Ground |
| Pino 82 | RF2 — I/O port RF2 |
| Pino 83 | RF3 — I/O port RF3 |
| Pino 84 | RF4 — I/O port RF4 |
| Pino 85 | RF5 — I/O port RF5 |
| Pino 86 | RF6 — I/O port RF6 |
| Pino 87 | RF7 — I/O port RF7 |
| Pino 88 | RF8 — I/O port RF8 |
| Pino 89 | RG0 — I/O port RG0 |
| Pino 90 | RG1 — I/O port RG1 |
| Pino 91 | RG2 — I/O port RG2 |
| Pino 92 | RG3 — I/O port RG3 |
| Pino 93 | RG6 — I/O port RG6 |
| Pino 94 | RG7 — I/O port RG7 |
| Pino 95 | RG8 — I/O port RG8 |
| Pino 96 | RG9 — I/O port RG9 |
| Pino 97 | D+ — USB D+ data line |
| Pino 98 | D- — USB D- data line |
| Pino 99 | VDD — Supply 2.5-3.3V |
| Pino 100 | VSS — Ground |
Aplicações típicas
PIC32MX564F128LT-I/PT é adequado para 6 aplicaçãos: USB-to-CAN Industrial Bridge, HMI Panel with TFT LCD, USB Barcode Scanner / Data Logger, CAN-Based Sensor Node, USB Device Firmware Upgrade Hub, In-Vehicle CAN Infotainment Subnode.
USB-to-CAN Industrial Bridge
The PIC32MX564F128LT-I/PT's integrated USB 2.0 full-speed device controller and CAN 2.0B active peripheral make it ideal for USB-to-CAN bridging gateways used in industrial automation and diagnostic tools. With 80 MHz MIPS32 M4K core throughput and 4-channel DMA, the MCU sustains bidirectional USB-CAN traffic at 1 Mbit/s without CPU saturation. Place the part on a 4-layer PCB with 90 ohm D+/D- differential routing and an MCP2551 CAN transceiver on the bus side.
Recomendado
HMI Panel with TFT LCD
The 16-bit Parallel Master Port (PMP) on the PIC32MX564F128LT-I/PT directly drives graphical TFT LCDs up to 320x240 resolution without external display controllers, ideal for compact HMI panels. Combined with 128 KB Flash for GUI assets and 32 KB RAM for frame buffers, the part provides enough headroom for menu structures and small bitmaps. The 80 MHz core renders text and icon updates fast enough for fluid 30 Hz refresh with low interrupt latency.
Recomendado
USB Barcode Scanner / Data Logger
USB host mode on the PIC32MX564F128LT-I/PT enables direct connection to USB barcode scanners, RFID readers and USB mass storage for portable data loggers in warehouse and field-instrumentation applications. The 4-channel DMA offloads USB bulk transfer handling, freeing the 80 MHz M4K core for parsing scanned data and time-stamping events. The 128 KB Flash holds firmware plus a small FAT file-system library for SD-card mirroring.
Recomendado
CAN-Based Sensor Node
For distributed industrial sensor nodes, the PIC32MX564F128LT-I/PT combines CAN 2.0B with a 10-bit 1 Msps ADC for periodic analog sampling and broadcast over the bus. The 53 I/O pins handle multiple analog and digital sensors, while 4 DMA channels stream ADC conversions into RAM without CPU intervention. Designers use the part for predictive-maintenance nodes reporting vibration, temperature and current at 100 kbit/s CAN bus rates.
Recomendado
USB Device Firmware Upgrade Hub
In USB DFU application hubs and firmware-loading fixtures, the PIC32MX564F128LT-I/PT acts as a USB device that receives firmware images and re-flashes downstream targets via UART, SPI or I2C. The 128 KB Flash and 32 KB RAM are sufficient for USB stacks plus custom bootloader code. Engineers can implement vendor-specific USB classes with the on-chip full-speed transceiver, eliminating external PHY cost.
Recomendado
In-Vehicle CAN Infotainment Subnode
The PIC32MX564F128LT-I/PT's CAN 2.0B active peripheral and 80 MHz throughput support in-vehicle sub-node controllers for infotainment, HVAC and lighting subsystems communicating on the vehicle CAN bus. The 16-bit PMP can drive small auxiliary displays while the USB port handles media input or smartphone mirroring protocols. The 100-pin TQFP package exposes enough I/O for keypad scanning and LED matrix driving.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MX564F128LT-I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MX564F128HT-I/PT | PIC32MX564F128HT-V/PT | PIC32MX564F064LT-I/PT | PIC32MX564F064L-I/PT | PIC32MX470F512L-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-100 (12x12 mm) | TQFP-100 (12x12 mm) - same | TQFP-100 (12x12 mm) - same | TQFP-100 (12x12 mm) - same | TQFP-100 (12x12 mm) - same | TQFP-100 (12x12 mm) - same |
| Flash Size | 128 KB | 128 KB (same) | 128 KB (same) | 64 KB (-50%) | 64 KB (-50%) | 512 KB (+300%) |
| RAM Size | 32 KB | 32 KB (same) | 32 KB (same) | 32 KB (same) | 32 KB (same) | 32 KB (same) |
| Core Frequency | 80 MHz | 80 MHz (same) | 80 MHz (same) | 80 MHz (same) | 80 MHz (same) | 80 MHz (same) |
| USB 2.0 FS | Yes (Device/Host/OTG) | Yes (Device/Host/OTG) | Yes (Device/Host/OTG) | Yes (Device/Host/OTG) | Yes (Device/Host/OTG) | Yes (Device/Host/OTG) |
| CAN 2.0B | Yes | Yes | Yes | Yes | Yes | Yes |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +125C (Automotive V) | -40C to +85C (Industrial) | -40C to +85C (Industrial) | -40C to +85C (Industrial) |
Principais diferenciais
- Drop-in HT variant with extended temperature grade (vs PIC32MX564F128HT-I/PT)
- Industry-standard USB 2.0 full-speed with on-chip PHY (vs PIC32MX564F064L-I/PT)
- 4-channel hardware DMA for peripheral offload (vs PIC32MX534F064H-I/PT)
Notas de projeto
USB D+ (pin 97) and D- (pin 98) must be routed as a 90-ohm differential pair on a 4-layer PCB with controlled impedance. Keep the trace length under 50 mm and avoid stubs. Place the 48 MHz crystal within 5 mm of OSC1 (pin 30) and OSC2 (pin 31) with a grounded guard ring to minimize EMI pickup that would degrade USB signal integrity and cause enumeration failures.
Place a 0.1 uF ceramic decoupling capacitor within 5 mm of every VDD pin (5, 44, 60, 80, 99) and a 10 uF bulk tantalum or ceramic on the main 3.3V rail. Estimated: at 80 MHz the part draws ~70 mA active and ~25 mA idle; the bulk capacitor prevents supply droop during USB burst events. Use a low-ESR ceramic for the bulk cap to handle transient load steps from USB full-speed packets.
Do not confuse the PIC32MX564F128L-I/PT suffix L (Industrial temperature grade, -40C to +85C) with the package code PT (100-pin TQFP). The 'T' in the MPN is the tape-and-reel packaging suffix, not a separate variant. When migrating from PIC32MX564F064L to PIC32MX564F128L, verify firmware size - although both fit in the same MPLAB X IDE project, the linker scripts and Flash layout differ between 64 KB and 128 KB parts.
Estimated: at 80 MHz core clock and 3.3V supply the part dissipates approximately 250 mW. The 100-pin TQFP has theta_JA around 50 C/W on a 4-layer JEDEC test board, giving a 12.5 C junction rise above ambient at full load - well within the industrial -40C to +85C rating. For enclosed housings, ensure 100 sq cm of copper pour on the top layer connected to VSS for additional heat spreading.
Informações de conformidade
RoHS and lead-free compliant per Microchip product page. PIC32MX564F128HT-V/PT is the AEC-Q100 qualified variant for automotive; the -LT (this MPN) is industrial grade only. Halogen-free status not explicitly stated in the retrieved data.
