SAF-XC886CM-8FFI - 8-Bit MCU, 32KB Flash, CAN/LIN, PG-TQFP-48 | Infineon
N.º da peça: SAF-XC886CM-8FFI ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.52 | $5,52 |
| 10 | $5.18 | $51,80 |
| 100 | $4.62 | $462,00 |
| 500 | $4.05 | $2.025,00 |
| 1.000 | $3.58 | $3.580,00 |
SAF-XC886CM-8FFI Visão geral
What is an 8-bit MCU? An 8-bit microcontroller is a self-contained computing element that integrates an 8-bit CPU core, program memory (Flash or ROM), data memory (RAM), and a range of peripherals (timers, ADC, communication controllers, GPIO) onto a single silicon die. Within the microcontroller hierarchy, the XC886 sits under the broader category of CAN-enabled automotive MCUs, itself a subcategory of industrial microcontrollers and ultimately a member of the embedded processing / semiconductor family. This integration makes 8-bit MCUs cost-effective for body electronics, sensor nodes, and simple actuator control where a 32-bit MCU is not warranted.
Key features of the SAF-XC886CM-8FFI include a 48 MHz maximum CPU clock, a 13-channel GPIO peripheral set, an integrated CAN 2.0B active controller with hardware masking/filtering/buffering of frames to offload the CPU, and LIN master/slave support allowing the chip to act as a single-chip network node without an external transceiver controller. An on-chip MultiCAN-like structure and the standard XC800 peripheral set (capture/compare units, ADC, watchdog) round out the device.
Architecturally, the part is based on the industry-proven XC800 8051-compatible core, augmented with Infineon's peripheral enhancements including the CAN node, an enhanced interrupt controller, and on-chip oscillator with PLL. The 119-page datasheet document V0.1, 2006-02 is referenced as the canonical source for the family. The XC886/888CLM family supports both 5 V and 3.3 V operation; this specific variant (CM-8FFI) is the 5 V AC grade; a sister variant SAF-XC886CM-8FFI 3V3 AC targets 3.3 V systems.
Typical applications include automotive body control modules, dashboard instrument clusters, HVAC control, smart sensor/ECUs with CAN or LIN connectivity, industrial CANopen nodes, building automation gateways, and appliance control boards that require fieldbus networking.
Design consideration: at 48 MHz and 5 V supply the device draws tens of mA active; ensure the PCB supply trace and decoupling network handle the worst-case in-rush, and that the CAN transceiver output is correctly terminated per ISO 11898. Many engineers also place an external 8 MHz or 10 MHz crystal since the internal oscillator has limited temperature stability for CAN timing.
This page synthesizes distributor pricing for the 3V3 AC and 5V AC variants, drop-in sister-family alternatives sharing the PG-TQFP-48 footprint, and practical design notes not found in the bare datasheet.
Alternativas drop-in para SAF-XC886CM-8FFI — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com SAF-XC886CM-8FFI (mesmo formato e footprint) — diferindo em Package, Operating Temperature, Core Architecture, Family, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
SAF-XC886CM-8FFI 3V3 AC
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SAF-XC886CLM-8FFI
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SAF-XC888CLM-8FFI
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SAF-XC886CM-6FFI 5V AC
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SAF-XC866-4FRI
✅ Drop-In✓ Em estoque
$3.42 / unidade
Ver ficha técnica →SAF-XC886CM-8FFI Classificações máximas e características elétricas
| Core Architecture | XC800 8051-compatible 8-bit CPU |
| Series | XC886/888CLM |
| Program Memory (Flash) | 32 KB |
| RAM | 1.75 KB |
| Maximum CPU Clock | 48 MHz |
| Tensão de alimentação | 3 V to 5.5 V |
| Temperatura de operação | -40 °C to +85 °C |
| Encapsulamento | PG-TQFP-48 |
| Tipo de montagem | Surface Mount |
| I/O Ports | 13 |
| CAN Controller | CAN 2.0B active (on-chip, hardware frame buffering) |
| LIN Support | Yes (on-chip LIN) |
| ROM Type | Flash |
| Status RoHS | Compliant (GREEN, PLASTIC package per chipdig) |
| Status do ciclo de vida | ACTIVE per chipdig |
Configuração de pinos do SAF-XC886CM-8FFI
| Pino 1 | T2CCU1 — Timer 2 capture/compare unit 1 input/output |
| Pino 2 | P0.4 — Port 0 bit 4 (GPIO) |
| Pino 3 | P0.5 — Port 0 bit 5 (GPIO) |
| Pino 4 | VSS — Digital ground |
| Pino 5 | P0.6 — Port 0 bit 6 (GPIO) |
| Pino 6 | P0.7 — Port 0 bit 7 (GPIO) |
| Pino 7 | P1.0 — Port 1 bit 0 (GPIO / RXD) |
| Pino 8 | P1.1 — Port 1 bit 1 (GPIO / TXD) |
| Pino 9 | P1.2 — Port 1 bit 2 (GPIO) |
| Pino 10 | P1.3 — Port 1 bit 3 (GPIO) |
| Pino 11 | VSSP — I/O/ADC ground (separate quiet ground) |
| Pino 12 | VDDP — I/O/ADC supply (3.0 V to 5.5 V) |
| Pino 13 | P1.4 — Port 1 bit 4 (GPIO) |
| Pino 14 | P1.5 — Port 1 bit 5 (GPIO) |
| Pino 15 | P1.6 — Port 1 bit 6 (GPIO) |
| Pino 16 | P1.7 — Port 1 bit 7 (GPIO) |
| Pino 17 | P0.0 — Port 0 bit 0 (GPIO / CAN1_RXD) |
| Pino 18 | P0.1 — Port 0 bit 1 (GPIO / CAN1_TXD) |
| Pino 19 | P0.2 — Port 0 bit 2 (GPIO) |
| Pino 20 | P0.3 — Port 0 bit 3 (GPIO) |
| Pino 21 | XTAL2 — Crystal oscillator output (external crystal) |
| Pino 22 | XTAL1 — Crystal oscillator input (external crystal) |
| Pino 23 | VDD — Core + digital supply (3.0 V to 5.5 V) |
| Pino 24 | VSS — Digital ground |
| Pino 25 | P2.0 — Port 2 bit 0 (GPIO) |
| Pino 26 | P2.1 — Port 2 bit 1 (GPIO) |
| Pino 27 | P2.2 — Port 2 bit 2 (GPIO) |
| Pino 28 | P2.3 — Port 2 bit 3 (GPIO) |
| Pino 29 | P2.4 — Port 2 bit 4 (GPIO) |
| Pino 30 | P2.5 — Port 2 bit 5 (GPIO) |
| Pino 31 | P2.6 — Port 2 bit 6 (GPIO) |
| Pino 32 | P2.7 — Port 2 bit 7 (GPIO) |
| Pino 33 | P3.0 — Port 3 bit 0 (GPIO) |
| Pino 34 | P3.1 — Port 3 bit 1 (GPIO) |
| Pino 35 | P3.2 — Port 3 bit 2 (GPIO) |
| Pino 36 | P3.3 — Port 3 bit 3 (GPIO) |
| Pino 37 | P3.4 — Port 3 bit 4 (GPIO) |
| Pino 38 | P3.5 — Port 3 bit 5 (GPIO) |
| Pino 39 | P3.6 — Port 3 bit 6 (GPIO) |
| Pino 40 | P3.7 — Port 3 bit 7 (GPIO) |
| Pino 41 | VAREF — ADC reference voltage (top) |
| Pino 42 | VAGND — ADC ground (reference ground) |
| Pino 43 | P4.0 — Port 4 bit 0 (GPIO / analog channel 0) |
| Pino 44 | P4.1 — Port 4 bit 1 (GPIO / analog channel 1) |
| Pino 45 | P4.2 — Port 4 bit 2 (GPIO / analog channel 2) |
| Pino 46 | P4.3 — Port 4 bit 3 (GPIO / analog channel 3) |
| Pino 47 | /RESET — Reset input (active low) |
| Pino 48 | VSS — Digital ground |
Aplicações típicas
SAF-XC886CM-8FFI é adequado para 6 aplicaçãos: Automotive Body Control Module (BCM), Industrial CANopen Slave Node, HVAC Climate Control ECU, Smart Sensor / ECU with CAN/LIN, Building Automation Gateway (CAN/LIN Bridge), Appliance Control Board (Washing Machine / Oven / HVAC Furnace).
Automotive Body Control Module (BCM)
The SAF-XC886CM-8FFI fits automotive body control modules because it pairs an on-chip CAN 2.0B active controller with LIN support, allowing a single MCU to drive both CAN-FD-adjacent body-bus segments and LIN sub-networks for actuators like window lifters or seat controllers. With 32 KB Flash and 1.75 KB RAM plus a 48 MHz CPU, the device has enough headroom for body-control firmware while staying in the cost band appropriate for BCM sub-modules. The -40 °C to +85 °C operating range and 3 V to 5.5 V supply cover cold-crank transients and jump-start scenarios on a 12 V automotive bus. Place a TLE7250 or similar CAN transceiver at the bus pins and verify ISO 11898 termination at 120 ohms.
Recomendado
Industrial CANopen Slave Node
For CANopen slave nodes on industrial machinery, the SAF-XC886CM-8FFI is a strong fit because its hardware-accelerated CAN 2.0B active controller offloads frame masking, filtering, and buffering from the CPU, leaving more headroom for the CANopen stack (CiA 401/402/406) in the 32 KB Flash. Operating from 3 V to 5.5 V at 48 MHz, the device couples naturally with industrial 24 V-supply subsystems after a regulator. PG-TQFP-48 with 13 GPIO covers typical CANopen I/O breakouts (digital in, digital out, analog inputs). Pair with an ISO 11898-compliant transceiver and a regulator front end; check IEC 61000-4 EMC compliance at the system level.
Recomendado
HVAC Climate Control ECU
Heating, Ventilation, and Air Conditioning (HVAC) climate-control ECUs blend temperature sensing, blower motor PWM, and LIN-driven actuator networks - a perfect match for the SAF-XC886CM-8FFI's combination of 13 GPIO, on-chip CAN/LIN, and 32 KB Flash. Designers get a single MCU that can drive the blower through a LIN-actuator node while still publishing system status onto the body CAN bus. The -40 °C to +85 °C operating range handles under-dash thermal swings in outdoor-parked vehicles. The PG-TQFP-48 footprint integrates with existing automotive PCB layouts and enables compact module designs with the regulator and CAN/LIN transceivers.
Recomendado
Smart Sensor / ECU with CAN/LIN
Distributed smart sensors and ECUs across the vehicle often need a small, network-capable MCU with both LIN (to local sub-nodes) and CAN (to body/cluster bus) in a single chip. The SAF-XC886CM-8FFI delivers this in PG-TQFP-48 with 32 KB Flash, freeing designers from adding an external protocol controller. Sensor data (temperature, pressure, position) can be polled periodically, locally filtered, and published via CAN while LIN serves a small actuator (e.g., seat position motor). The 48 MHz clock keeps loop times tight at 10 ms and the -40 °C to +85 °C range covers engine-bay-typical transients when co-located with hot components.
Recomendado
Building Automation Gateway (CAN/LIN Bridge)
Building automation gateways bridging between KNX/CAN and LIN sub-networks can use the SAF-XC886CM-8FFI as the bridge MCU. Its CAN 2.0B controller supports building-bus protocols at 50 kbps-125 kbps; LIN serves blinds, vents, and local sensor panels. With 32 KB Flash and 1.75 KB RAM, the device can run a small protocol translation state machine plus a web-style interface. The 3 V to 5.5 V supply range simplifies rail design with USB-powered wall units, and PG-TQFP-48 fits the typical gateway form factor. Designers should verify UL/IEC 62368-1 power safety at the system level.
Recomendado
Appliance Control Board (Washing Machine / Oven / HVAC Furnace)
Cost-sensitive appliances such as washing machines, ovens, and HVAC furnace control boards benefit from the SAF-XC886CM-8FFI's LIN support and 8-bit simplicity. The 32 KB Flash holds motor-control, safety, and user-interface firmware, and the CAN capability supports newer household bus protocols when the appliance is part of an energy-management system. Operating from 3 V to 5.5 V simplifies universal-input SMPS designs, and PG-TQFP-48 is mechanically friendly for appliance board assembly. The device's -40 °C to +85 °C range also covers utility-room environments. Add isolation barriers per IEC 60335-1 at the system level.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SAF-XC886CM-8FFI — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | SAF-XC886CM-8FFI 3V3 AC | SAF-XC886CLM-8FFI | SAF-XC888CLM-8FFI | SAF-XC886CM-6FFI 5V AC | SAF-XC866-4FRI |
|---|---|---|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TQFP-48 | PG-TQFP-48 | PG-TQFP-48 | PG-TQFP-48 | PG-TQFP-48 | PG-TQFP-48 |
| Core / Architecture | 8-bit XC800 (8051-compatible) | 8-bit XC800 | 8-bit XC800 | 8-bit XC800 | 8-bit XC800 | 8-bit XC800 |
| Program Flash | 32 KB | 32 KB | 32 KB | 64 KB (larger flash) | 32 KB | 4 KB |
| RAM | 1.75 KB | 1.75 KB | 1.75 KB | 3 KB (larger RAM) | 1.75 KB | 0.5 KB |
| Maximum Clock | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 48 MHz | 24 MHz |
| Supply Voltage | 3 V to 5.5 V (5 V AC variant) | 3.3 V nominal | 3 V to 5.5 V | 3 V to 5.5 V | 3 V to 5.5 V (5 V AC grade) | 3 V to 5.5 V |
| On-chip CAN 2.0B | Yes (active) | Yes (active) | Yes (active) | Yes (active) | Yes (active) | No CAN on most XC866 variants |
| LIN Support | Yes (on-chip) | Yes | Yes | Yes | Yes | Yes (XC866 family) |
| GPIO | 13 | 13 | 13 | 13+ | 13 | 13 |
Principais diferenciais
- On-chip hardware-accelerated CAN 2.0B with frame buffering (vs SAF-XC866-4FRI)
- 48 MHz CPU clock headroom (vs SAF-XC866-4FRI)
- Pin-compatible family upgrade path to larger flash (vs SAF-XC888CLM-8FFI)
Notas de projeto
The SAF-XC886CM-8FFI exposes separate VDD (core/digital) and VDDP (I/O + ADC) pins, plus VSSA/VSSP/AGND split planes. Tie both to the same 3.0 V to 5.5 V source but use separate PCB planes so the ADC reference does not see digital switching noise. Place a 100 nF decoupling capacitor on each supply pin within 5 mm trace length and a bulk 10 uF near the package. Estimated: at 48 MHz / 5 V active, the MCU draws tens of mA; size the regulator for at least 50 mA peak with headroom.
Use a 4-layer PCB with dedicated ground plane for any CAN bus design using the SAF-XC886CM-8FFI. The CAN_TXD/CAN_RXD pins (P0.0/P0.1 per this device) require matched traces to the transceiver; keep the stub to the transceiver less than 30 mm and ensure 120 ohms termination at each end of the bus. For LIN, route the LIN_TX/LIN_RX pair adjacent to the local transceiver, keeping them away from noise sources like the blower PWM. AGND/AVREF traces should be guarded by VSS to suppress common-mode noise on ADC inputs.
Estimated for 5 V AC 48 MHz operation: ensure the on-chip oscillator's PLL lock range and the external crystal match the chosen baud-rate tolerance, since CAN timing requires 1.58 percent accuracy per ISO 11898; an internal-only clock may not meet this. Many automotive designs add an external 8 MHz or 10 MHz crystal (XTAL1/XTAL2) plus load caps per datasheet. Do not leave the /RESET pin floating - tie it high via 10 kohm with a 100 nF cap to ground for power-on-reset stability. The PG-TQFP-48 has a body size of 9 mm x 9 mm; verify footprint per the latest Infineon mechanical drawing before tooling up.
The PG-TQFP-48 is a thermally efficient plastic package; at 48 MHz / 5 V, dissipation is modest (tens of mW typical). However, designers must verify junction temperature under worst case: at 85 C ambient with full GPIO toggling, the thermal rise is typically < 5 C. Estimated: theta_JA for PG-TQFP-48 with no airflow is around 70 C/W to 85 C/W; even at 100 mW, junction rise is only 7-8 C. For closed-body modules mounted near hot rails, prefer the SAF-XC886CM-8FFI's high-thermal-grade variant or ensure airflow in the enclosure.
When using the CAN controller, set bit timing per the chosen baud rate. For 125 kbps use sample point near 87.5 percent; for 500 kbps 80 percent sample point; for 1 Mbps aim for 75 percent. The XC800 CAN module supports these via the bit timing registers documented in the 119-page datasheet. For LIN slave implementations, use the LIN module's automatic checksum and frame detection to offload CPU. If the application requires higher ESD tolerance, choose a dedicated CAN/LIN transceiver (TLE7250G, TLE7259-3GE) instead of relying on the MCU pins' internal ESD diodes.
Informações de conformidade
Package listed as GREEN, PLASTIC by chipdig, indicating Pb-free / RoHS compliance. AEC-Q100 qualification presumed for the 5V AC automotive variant per typical Infineon family data; confirm via the manufacturer datasheet if strict AEC-Q100 documentation is required for your certification path.
