STM32G0B1KET6 - 64MHz Cortex-M0+ 512KB MCU | STMicroelectronics
N.º da peça: STM32G0B1KET6 ✓ AtivoSTM32G0B1KET6 Visão geral
An Arm Cortex-M0+ microcontroller is a compact 32-bit RISC processor used in embedded control products. The STM32G0 family combines the Cortex-M0+ core with timers, serial interfaces, analog peripherals, GPIO, memory, and security features on one integrated circuit. This places the STM32G0B1KET6 within the hierarchy of microcontroller, embedded processor, RISC processor, and semiconductor, allowing one device to manage sensing, communications, actuation, and system control.
The most prominent specifications are a 64 MHz maximum operating frequency, 512 KB of embedded Flash, and 144 KB of SRAM. According to the manufacturer product-page information, the STM32G0B1xB family uses a high-performance Cortex-M0+ 32-bit RISC core. Flash protection, a securable area, two memory banks, and read-while-write support are identified for this memory configuration. Six USART peripherals support serial links to sensors, human-interface equipment, module radios, and external controllers.
The STM32G0B1KET6 supports a 1.8 V, 2.5 V, or 3.3 V supply as identified for the exact ordering code. Its operating-temperature options extend down to -40°C and can reach 85°C, 105°C, or 125°C across the STM32G0B1xB/xC/xE family. The 32-LQFP package provides 32 accessible leads and a 7 x 7 mm body, making it suitable for automated assembly and medium-density embedded control boards.
Typical applications include compact industrial controllers, building and access modules, motor-control auxiliaries, connected sensors, communication equipment, and consumer peripherals. Six USARTs are particularly useful when a design needs multiple isolated serial links without adding a separate interface expander. A 512 KB Flash capacity also allows firmware, boot logic, communication tables, and application data to coexist within one MCU.
When designing the PCB, place decoupling capacitors beside the supply and ground pins and route sensitive analog and communication lines away from fast-switching nodes. Confirm the exact peripheral mapping, pin multiplexing, clock-tree settings, and boot configuration against the manufacturer datasheet before releasing a board. Software compatibility should also be checked because alternative Cortex-M0+ devices may use different peripheral registers or interrupt arrangements.
This product page consolidates the exact ordering-code characteristics, family-level engineering details, package information, and purchasing workflow. It also distinguishes genuine package-compatible alternatives from devices that merely share the STM32G0 name, helping engineers make a defensible sourcing decision without assuming that every similarly described MCU is a drop-in replacement.
Alternativas drop-in para STM32G0B1KET6 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Nenhuma alternativa drop-in disponível para este produto.
Solicitar alternativasSTM32G0B1KET6 Classificações máximas e características elétricas
| Product Type | 32-bit Arm Cortex-M0+ RISC microcontroller |
| Maximum CPU Frequency | 64 MHz |
| Flash Memory | 512 KB |
| Flash Organization | 512K x 8 |
| RAM | 144 KB |
| USART Count | 6 |
| Tensão de alimentação de operação | 1.8 V, 2.5 V, or 3.3 V |
| Temperatura de operação | -40°C to 85°C |
| Encapsulamento | 32-LQFP, 7 x 7 mm |
| Lead Count | 32 |
| Tipo de montagem | Surface mount |
| CPU Architecture | Arm Cortex-M0+ |
| Instruction Width | 32 bit |
| Flash Memory Banks | 2 |
| Flash Read-While-Write | Supported |
| Flash Protection | Supported |
| Securable Flash Area | Supported |
| Packing Type | Tray |
| Status RoHS | Compliant |
Guia de Configuração de Pinos do STM32G0B1KET6 32-lqfp, 7 x 7 mm
Configuração de pinos para STM32G0B1KET6 (pacote 32-lqfp, 7 x 7 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para STM32G0B1KET6.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
STM32G0B1KET6 é adequado para 6 aplicaçãos: Industrial serial controller, Connected sensor gateway, Building and access module, Motor-control auxiliary controller, Communication concentrator, Low-voltage embedded control.
Industrial serial controller
The STM32G0B1KET6 fits compact industrial controllers that must coordinate several external serial devices without adding a separate communication expander. Its six USART peripherals support concurrent links to sensors, programmable controllers, local displays, radios, or service connectors. The 64 MHz Cortex-M0+ core provides useful control bandwidth, while 512 KB of Flash and 144 KB of RAM accommodate protocol handlers, diagnostics, configuration data, and application firmware. Designers should reserve UART pins according to the exact 32-LQFP datasheet and isolate external interfaces with appropriate protection for industrial voltage and surge conditions.
Recomendado
Connected sensor gateway
The STM32G0B1KET6 is suitable for a connected sensor gateway that aggregates readings from multiple modules and forwards status or configuration data. Six USARTs allow the gateway to connect several sensors or local radio modules, while the 144 KB RAM can buffer incoming and outgoing data. Its 1.8 V operating option supports low-voltage designs where a compatible sensor or radio shares the 3.3 V rail. Firmware can use the protected, securable Flash configuration for credentials, and designers should isolate radio and sensor paths to limit conducted noise and ground-current coupling.
Recomendado
Building and access module
Building-access hardware can use the STM32G0B1KET6 to manage locks, request-to-exit inputs, card readers, displays, and diagnostic communications. The Cortex-M0+ operating speed of up to 64 MHz is sufficient for event handling and protocol tasks, while 512 KB of Flash provides room for communication stacks, device identity, and firmware updates. Six USARTs offer flexibility for a reader, controller, BLE or radio module, and service interface. A robust design should include watchdogs, brownout behavior, input protection, and controlled actuator power rather than driving locks directly from general-purpose GPIO.
Recomendado
Motor-control auxiliary controller
The STM32G0B1KET6 can serve as an auxiliary controller in motor-control systems where sensing, communications, and protection logic must operate alongside a dedicated gate-driver or motor-control MCU. Its 512 KB Flash and 144 KB RAM support state machines, current and position processing, fault logs, and field-bus diagnostics. Six USARTs can handle a tuning interface, encoder or sensor links, and an external drive module. The controller should be isolated from switching-node energy, use filtered measurement paths, and coordinate shutdown signals so that loss of communications or unexpected fault states cannot leave the motor energized.
Recomendado
Communication concentrator
The STM32G0B1KET6 is appropriate for a small communication concentrator that bridges multiple serial endpoints to a host processor. Its six USARTs reduce the number of external interface components, and the 512 KB Flash provides room for framing, routing tables, diagnostics, and bootloader functions. The 144 KB RAM supports multiple receive and transmit buffers, allowing the firmware to service several ports without immediately offloading traffic to external memory. Design the UART baud-rate tolerance and buffer occupancy conservatively, and provide galvanic isolation or surge protection where connected lines extend beyond the enclosure.
Recomendado
Low-voltage embedded control
The STM32G0B1KET6 fits low-voltage embedded-control boards built around a 1.8 V, 2.5 V, or 3.3 V supply. Selecting the appropriate operating voltage permits direct interfacing with low-energy sensors, displays, and transceivers, reducing the number of level-shift stages. The Cortex-M0+ core runs at up to 64 MHz, giving responsive control and communication handling, while 144 KB of RAM and 512 KB of Flash reduce external component count. Power-budget analysis should include regulator quiescent current, MCU operating mode, and load-switch sequencing rather than relying only on nominal active-mode performance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para STM32G0B1KET6 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Principais diferenciais
- Substantially larger memory configuration than the smaller STM32G031K6T6 (vs STM32G031K6T6)
- Six-USART integration reduces external interface count (vs STM32G0B1CBT6)
- Explicit operating-voltage options support compact mixed-voltage systems (vs STM32F103R6T6ATR)
Notas de projeto
Place the required supply-decoupling capacitor adjacent to the MCU power pin and connect it to the ground reference with a short, low-inductance path. Route the 32-LQFP lands to the manufacturer package drawing rather than a generic STM32G0 footprint, because related devices can use different lead configurations. Keep oscillator and debug connections away from switching power inductors, and provide clean access to the programming and debug interface for production programming.
Build the power tree around one of the identified 1.8 V, 2.5 V, or 3.3 V operating conditions and verify every external peripheral's voltage tolerance. Check peak current in startup, transmit, and actuator states rather than average consumption alone. If several serial devices share the rail, include local decoupling at each device and sequence loads where reset timing matters. Use the manufacturer power-pin and decoupling recommendations in the final schematic review.
Do not assume that every similarly named STM32G0 device has the same pinout, memory capacity, or peripheral set. The STM32G0B1CBT6 comparison reports equivalent primary performance, but its package and lead assignment must be confirmed before PCB reuse. Likewise, the STM32G031K6T6 uses a smaller resource configuration and is not an automatic substitute. Validate boot pins, GPIO alternate functions, clock sources, interrupts, and firmware support separately from footprint matching.
Assign the six UART functions early because their alternate-function options can constrain the placement of communication connectors and GPIO. Keep long external serial routes away from sensitive analog inputs, and terminate or bias unused communication lines according to their protocol. Provide a common low-impedance ground plane, keep return paths short, and isolate externally accessible interfaces with the appropriate protection network. Validate the final layout for EMC and ESD requirements applicable to the enclosure and installation environment.
Informações de conformidade
RoHS compliance and Ecopack2 industrial-grade status are identified in the comparison data. Other environmental and automotive compliance fields are not established for the exact ordering code.