Texas Instruments

TAS5121DKDR - 100W Mono Class D Amp | Texas Instruments

N.º da peça: TAS5121DKDR ✓ Ativo
10.8 V to 13.2 V Vdss 36-HSSOP with exposed pad Package
MOQ: 1 |

TAS5121DKDR Visão geral

Texas Instruments TAS5121DKDR is a 1-channel mono Class D digital power-stage amplifier rated for 100 W into a 4 ohm load, with a 10.8 V to 13.2 V supply range, housed in a 36-pin HSSOP package with an exposed pad. It accepts digital audio inputs and includes short-circuit, thermal-event, and shutdown functions.

A Class D amplifier is a switching audio power amplifier that converts a digital pulse-width-modulated input into a high-current, filtered speaker output. It belongs to the hierarchy of digital amplifiers, audio amplifiers, amplifier ICs, and power-management semiconductors. Compared with a linear output stage, its switching architecture can support high output power efficiently while leaving less energy in the device during amplification.

The TAS5121DKDR's headline specifications are 100 W output into 4 ohms, a 13.2 V maximum listed supply, and a 36-terminal HSSOP package. Its digital input architecture allows it to operate with a compatible TI audio host or PWM source. Short-circuit protection, thermal-event protection, and shutdown mode support safer system integration when the amplifier is used in consumer audio, portable equipment, or powered speaker designs.

The mono configuration means one power stage drives one speaker channel, while the separate digital control interface supports clocked audio data. The exposed package pad provides the primary thermal path from the switching power stage to the PCB. Its thermal performance therefore depends strongly on copper area, via placement, enclosure airflow, and the operating load rather than only on the nominal package rating.

Typical uses include powered speakers, subwoofers, compact consumer-audio systems, soundbars, portable audio products, and multimedia equipment. The device is particularly appropriate when a host processor already generates the required digital audio signal and the system needs a dedicated high-power mono output stage. The 10.8 V minimum supply should be considered when sizing the upstream regulator.

Design the PCB with the exposed pad tied to ground, adequate input and output decoupling, and short, wide power-loop paths. Confirm the speaker impedance, PWM format, clock configuration, thermal limits, and shutdown polarity against the manufacturer datasheet. Avoid long output traces or narrow copper connections that can increase inductance, ringing, and power loss at high current.

This page combines the component's manufacturer-defined electrical and packaging characteristics with practical thermal guidance, source-backed alternatives, and an application-oriented comparison. It is intended to help engineers evaluate the TAS5121DKDR as a high-power mono Class D output stage and identify whether a verified pin-compatible alternative is appropriate for the target design.

Alternativas drop-in para TAS5121DKDR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

TAS5121IDKDE4

✅ Drop-In
📦 36-SSOP with exposed pad
Industrial-temperature grade versus the TAS5121DKDR commercial grade; the 36-pin SSOP-family package and digital power-stage architecture remain aligned.

📋 Alternativa de referência (fora do catálogo)

TAS5121DKDR Classificações máximas e características elétricas

Amplifier Type Digital power-stage amplifier
Channel Count 1 channel (mono)
Amplifier Class Class D
Maximum Output Power 100 W into 4 ohms
Load Impedance 4 ohms
Supply Voltage Range 10.8 V to 13.2 V
Input Interface Digital audio input
Short-Circuit Protection Yes
Thermal-Event Protection Yes
Shutdown Function Yes
Technology PurePath Digital
Encapsulamento 36-HSSOP with exposed pad
Terminal Count 36 terminals
Package Shape Rectangular
Terminal Form Gull wing
Temperature Grade Commercial

Guia de Configuração de Pinos do TAS5121DKDR rectangular

Configuração de pinos para TAS5121DKDR (pacote rectangular). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.

Diagrama de pinagem do pacote rectangular para TAS5121DKDR

Nenhum dado detalhado de pinagem disponível para TAS5121DKDR.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

TAS5121DKDR é adequado para 6 aplicaçãos: Powered Subwoofer, Compact Powered Speaker, Soundbar Bass Channel, Portable Audio Product, Digital Audio Speaker Module, Professional Monitor Enclosure.

🔊

Powered Subwoofer

The TAS5121DKDR fits a powered subwoofer because its mono Class D architecture is rated for 100 W into a 4 ohm load. It accepts a digital audio signal from the enclosure's host processor, avoiding a separate analog power-amplifier output stage. The 10.8 V to 13.2 V operating range requires a supply designed for the required peak current, while the exposed HSSOP pad requires a low-resistance thermal path. Add the manufacturer-recommended output-filter network and validate the crossover response, speaker impedance, and maximum thermal operating condition.

🖥️

Compact Powered Speaker

A compact active speaker can use the TAS5121DKDR as its dedicated mono output stage when the design targets a high-power driver such as a 4 ohm woofer. The device's 100 W rating provides useful headroom for a Class D power amplifier, while digital input allows the speaker controller to retain control of volume, EQ, and mute functions. The 36-pin HSSOP package is surface-mountable, but the exposed pad and output-current path demand deliberate copper and via planning. Confirm the enclosure's heat dissipation before rating the speaker for continuous full-power operation.

📺

Soundbar Bass Channel

The TAS5121DKDR can serve the bass channel of a soundbar when one speaker requires up to 100 W and digital audio control is available from the main audio processor. Using a dedicated mono Class D stage simplifies channel routing and avoids driving a low-impedance woofer from a conventional analog output. The device's shutdown function can support system power management, while short-circuit and thermal-event protection improve fault tolerance. Integration must account for the 10.8 V minimum supply, filter selection, channel delay, and synchronization with the soundbar's main amplifier channels.

📱

Portable Audio Product

The TAS5121DKDR can support a high-output portable-audio product when its supply and thermal environment can sustain the required Class D output. Its digital input is useful in designs where a codec or application processor performs volume and signal processing before the power stage. The 13.2 V maximum supply keeps the device in a conventional single-rail architecture, although peak-current capability must be checked against the battery or regulator design. Use shutdown to reduce consumption when inactive and verify enclosure temperature rise during sustained playback.

🧩

Digital Audio Speaker Module

The TAS5121DKDR is appropriate for a standalone digital speaker module that receives clocked audio data and converts it into a filtered Class D output for a passive driver. Integrating the digital input with the system controller enables coordinated volume control, mute, and diagnostics without requiring an analog input path. The 36-HSSOP outline supports compact surface-mount assembly, but the exposed pad must be tied to ground through multiple thermal vias. Validate digital timing, clock polarity, startup sequencing, and the output filter against the manufacturer's electrical-characteristics tables.

🎧

Professional Monitor Enclosure

A professional monitor enclosure can use the TAS5121DKDR for a dedicated high-power monitor driver when the digital signal chain already provides the required PWM audio stream. The 100 W into 4 ohm capability is useful for transient headroom, although sustained thermal performance depends on the enclosure and PCB copper. The exposed pad provides an efficient heat-spreading route, and shutdown can coordinate with system muting or fault conditions. Before deployment, verify the crossover, protection thresholds, EMI behavior of the output filter, and reliability at the highest ambient temperature expected in the enclosure.

Resumo dos produtos recomendados

TAS5121IDKDE4 Industrial-temperature same-family power stage Usado em: Powered Subwoofer, Compact Powered Speaker, Soundbar Bass Channel, Portable Audio Product, Digital Audio Speaker Module TAS5121 Base family designation Usado em: Powered Subwoofer, Soundbar Bass Channel, Digital Audio Speaker Module TAS5142DKDR Related TI Class D power-stage family Usado em: Compact Powered Speaker, Professional Monitor Enclosure TAS5086DBTR Texas Instruments Usado em: Portable Audio Product, Professional Monitor Enclosure
What is the TAS5121DKDR?
The TAS5121DKDR is a Texas Instruments 1-channel, mono Class D digital power-stage amplifier for high-power audio output. According to the manufacturer datasheet, it delivers up to 100 W into a 4 ohm load, operates from 10.8 V to 13.2 V, accepts digital audio input, and is packaged in a 36-pin HSSOP with an exposed pad.
What are the key specifications of TAS5121DKDR?
The TAS5121DKDR provides 100 W output into 4 ohms from a 10.8 V to 13.2 V supply. The manufacturer datasheet identifies a 1-channel mono Class D architecture, digital input, PurePath Digital technology, short-circuit and thermal-event protection, shutdown operation, and a 36-pin HSSOP package with an exposed thermal pad.
What output power does TAS5121DKDR deliver?
The TAS5121DKDR is rated to deliver 100 W into a 4 ohm speaker load. This rating describes the specified power-amplification capability; actual continuous output also depends on supply voltage, PCB thermal design, output filtering, speaker impedance, and signal level. Use the manufacturer power-amplifier design guidance when planning copper and cooling.
What is the operating voltage of TAS5121DKDR?
The TAS5121DKDR operates from 10.8 V to 13.2 V. According to the manufacturer datasheet, the 13.2 V upper limit applies to the device's supply, while the usable rail must also support the selected output power into the connected load. A regulated supply with appropriate local decoupling should be used.
Where can I download the TAS5121DKDR datasheet PDF?
The TAS5121DKDR datasheet PDF is available through the official Texas Instruments document link and the manufacturer-linked PDF copy listed on this page. The datasheet contains the authoritative pin descriptions, digital-interface timing, electrical limits, typical performance curves, and thermal information needed for PCB and system design.
Where can I find the TAS5121DKDR pinout?
The TAS5121DKDR pinout is shown in the manufacturer datasheet's pin-configuration section and electrical-characteristics tables. The device uses a 36-pin HSSOP package with an exposed pad, so the board design must also account for the exposed thermal and ground pad rather than treating it as an ordinary unexposed 36-pin outline.
Can TAS5121DKDR drive a 4 ohm speaker?
Yes, the TAS5121DKDR is specifically characterized for delivering 100 W into a 4 ohm load. The manufacturer datasheet is the controlling document for thermal conditions and output-filter requirements. Verify that the speaker network presents a supported impedance across its full frequency range and that the power supply can source the required current.
How should I thermally design a TAS5121DKDR board?
Use the exposed pad as the primary thermal path and connect it to the PCB ground plane with a dense thermal-via array. The manufacturer power-amplifier layout guidance emphasizes short, wide power paths, low-inductance output routing, and adequate copper for continuous dissipation. Thermal performance should be checked at the highest expected output power and worst-case ambient temperature.
What is the difference between TAS5121DKDR and TAS5121IDKDE4?
The primary documented distinction is the temperature grade: TAS5121DKDR is commercial grade, while TAS5121IDKDE4 is identified as an industrial-temperature version of the TAS5121 family. Both use a 36-pin SSOP-family outline. For a drop-in decision, also verify exposed-pad connections, digital timing, supply limits, and every pin assignment in the manufacturer datasheets.
Is TAS5121DKDR suitable for a powered subwoofer?
The TAS5121DKDR is suitable for a mono subwoofer or powered-speaker application when the system supplies compatible digital audio data and an appropriate LC output filter. Its 100 W capability into 4 ohms matches many high-power mono speaker designs. Validate the crossover, filter stability, thermal margin, and speaker-impedance profile before production.
When should I choose TAS5121DKDR over TAS5121IDKDE4?
Choose the TAS5121DKDR when a commercial-temperature grade is acceptable and the completed board operates within the manufacturer limits for that grade. Choose TAS5121IDKDE4 when industrial-temperature operation is required. Because the package family is the same, the decision should be based on temperature requirements and a complete pin and electrical comparison rather than footprint alone.
Is TAS5121DKDR the same as TAS5121DKD?
The TAS5121DKD and TAS5121DKDR belong to the same device family and package outline, but the orderable suffix can encode a different delivery format. Do not treat that similarity as permission to change parts without checking the manufacturer ordering information. For a production substitution, compare the exact suffix, exposed-pad implementation, temperature grade, and packing method.
What can replace TAS5121DKDR?
A true replacement must use the same 36-pin footprint, preserve the exposed-pad connection, and meet the digital-interface and power-stage requirements. The verified cross-reference search identifies TAS5121IDKDE4 as the closest distinct same-family option, differing primarily by industrial temperature grade. It should be treated as a drop-in candidate only after all pins and timing requirements are checked.
Is there a verified cross-brand drop-in replacement for TAS5121DKDR?
No verified cross-brand drop-in replacement for the TAS5121DKDR was identified in the available cross-reference results. A different manufacturer may offer a comparable Class D power stage, but similar output power alone does not establish pin compatibility, digital timing, exposed-pad connectivity, or shutdown behavior. Use the Request a Quote form for sourcing support and require complete datasheet validation.
Where can I buy TAS5121DKDR online?
Use the Request a Quote form on this page to request TAS5121DKDR availability, order quantity, and delivery information. The form allows the inquiry to be matched to the exact TAS5121DKDR suffix and package configuration. Stock and lead time should be confirmed at the time of quotation because integrated-circuit inventory can change rapidly.
What is the price and lead time for TAS5121DKDR?
Current pricing, stock, minimum order quantity, and lead time for the TAS5121DKDR should be obtained through the Request a Quote form on this page. The manufacturer defines the device as a 36-pin HSSOP digital mono power stage rated for 100 W into 4 ohms, so the quotation should identify that exact suffix and package rather than a generic TAS5121 family option.

Dados de referência de engenharia para TAS5121DKDR — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the TAS5121DKDR for a high-power mono Class D design that requires 100 W into a 4 ohm load, digital audio input, and commercial-temperature operation. Its 10.8 V to 13.2 V supply range and exposed-pad HSSOP package require careful regulator and thermal-layout planning. Select TAS5121IDKDE4 when the same package family and digital power-stage architecture are needed but industrial-temperature qualification is required. Before substituting it, verify every pin, the exposed-pad connection, clock and data requirements, shutdown polarity, and electrical limits in both manufacturer datasheets. Other TI Class D devices, including TAS5142DKDR, are useful comparisons for multi-channel or different output-power architectures, but they were not verified as pin-compatible replacements for the TAS5121DKDR. Do not select an alternative based only on wattage or package count; the digital interface and board-level thermal design remain the decisive constraints.

Comparação com alternativas

Parâmetro Este produto TAS5121IDKDE4
Package 36-HSSOP with exposed pad 36-SSOP with exposed pad
Brand Texas Instruments Texas Instruments
Channel Count 1 channel (mono) 1 channel (mono)
Amplifier Class Class D Class D
Temperature Grade Commercial Industrial
Digital Input Yes Yes
Technology PurePath Digital PurePath Digital
Exposed Thermal Pad Yes Yes

Principais diferenciais

  • Commercial temperature grade with the same-family pin-compatible option available (vs TAS5121IDKDE4)
  • High-power mono output in a surface-mount package (vs TAS5121IDKDE4)
  • Integrated digital control and fault protection (vs TAS5121IDKDE4)

Notas de projeto

Treat the exposed pad as the primary thermal and electrical connection for the Class D output stage. Place a dense array of thermal vias beneath the pad, provide uninterrupted ground-plane copper, and avoid placing a thermal break directly beneath the device. Validate the design at the maximum expected output power, highest ambient temperature, and worst-case supply voltage because the exposed-pad temperature depends on PCB copper, airflow, and neighboring heat sources.

Use short and wide connections for supply, ground, and output-current paths to minimize parasitic inductance and EMI radiation. Follow the manufacturer layout guidance for input, PWM, clock, ground, and output-filter placement. Keep sensitive digital and analog routing away from the switching node, and place protection, filtering, and decoupling components where they can form compact current loops rather than long point-to-point paths.

Estimated power dissipation can be calculated as P_D = (V_SUPPLY - V_OUT) multiplied by the average output current, using the actual rail and speaker waveform. This is an engineering estimate rather than a datasheet limit. Add regulator margin for peak Class D current, verify startup current, and ensure the shutdown and mute transitions do not create excessive supply transients or audible transients in the speaker.

Do not infer pin compatibility from the 36-pin package count alone. Confirm the exposed-pad connection, digital-clock requirements, input format, shutdown polarity, supply limits, and output-filter topology for every proposed substitution. Also verify the speaker impedance at all frequencies; a nominal 4 ohm speaker may present a lower impedance at resonance and cause a protection event or excessive amplifier stress.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The available manufacturer and distributor information identifies the commercial temperature grade but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. Automotive qualification is not applicable to this commercial-grade audio power stage.

Dados verificados em: 2026-11-15 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

TAS5121DKDR datasheet TAS5121DKDR pinout TAS5121DKDR datasheet pdf Texas Instruments TAS5121DKDR TAS5121 100W Class D amplifier TAS5121DKDR 36-HSSOP TAS5121DKDR powered subwoofer TAS5121DKDR vs TAS5121IDKDE4 TAS5121DKDR drop-in replacement TAS5121DKDR equivalent TAS5121DKDR price TAS5121DKDR stock TAS5121DKDR replacement TAS5121DKDR footprint

Componentes & termos relacionados

Texas Instruments TAS5121DKDR TAS5121IDKDE4 TAS5142DKDR TAS5121 Class D amplifier digital power-stage amplifier mono amplifier audio amplifier IC PurePath Digital PWM audio input digital audio interface 100 W output power 4 ohm speaker load 10.8 V minimum supply 13.2 V maximum supply short-circuit protection thermal-event protection shutdown mode 36-HSSOP exposed thermal pad surface-mount package powered subwoofer powered speaker soundbar
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ