TLD55411QUXUMA1 - 55V Buck-Boost LED Controller | Infineon
N.º da peça: TLD55411QUXUMA1 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $1.65 | $1,65 |
| 10 | $1.52 | $15,20 |
| 100 | $1.38 | $138,00 |
| 500 | $1.21 | $605,00 |
| 1.000 | $1.05 | $1.050,00 |
TLD55411QUXUMA1 Visão geral
A BUCK-BOOST LED driver controller is a switching topology that maintains a stable output current through an LED string regardless of whether the input voltage is above or below the LED string forward voltage. It belongs to the wider category of switch-mode power supply controllers (SMPS controllers), specifically the LED driver sub-category, sitting under power management ICs in the LITIX Power LED Driver family.
The wide VIN range covers 4.5V to 40V on the IC supply input and 4.5V to 55V on the power stage, allowing direct operation from 12V and 24V automotive rails as well as 48V nominal industrial bus voltages. The wide LED forward voltage range spans 2V up to 55V, supporting LED strings from a few high-brightness LEDs up to long strings of mid-power LEDs. A 1-channel output drives a single LED string with high-side current sense.
Internally, the device uses a synchronous MOSFET H-bridge topology on the power stage combined with a single external inductor, eliminating the need for a second magnetic component. The controller regulates either constant current (CC) or constant voltage (CV) depending on load conditions and is suitable for automotive front-light, daytime running light, and high-power general-illumination LED drivers. Diagnostic features and protection include LED open/short detection, over-temperature shutdown, and input undervoltage lockout.
Typical applications include automotive LED headlamp drivers, DRL (daytime running light) drivers, fog-lamp drivers, industrial high-bay LED fixtures, and architectural LED lighting where the input voltage may swing above and below the LED forward voltage during load-dump transients or cold-crank events.
When designing with the TLD55411QUXUMA1, ensure the input bulk capacitance is sized for the worst-case load-dump transient (up to 55V at the power stage) and that the high-side current-sense resistor is Kelvin-connected to minimize ground-loop errors. The exposed thermal pad must be soldered to a sufficient copper pour to handle the gate-drive and quiescent losses of the controller.
This page synthesizes distributor pricing, drop-in alternative coverage, application notes, and design pitfalls not consolidated in the manufacturer datasheet, helping engineers evaluate the TLD55411QUXUMA1 for new designs and as a replacement for legacy LED controllers.
Alternativas drop-in para TLD55411QUXUMA1 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com TLD55411QUXUMA1 (mesmo formato e footprint) — diferindo em Package, Operating Temperature Range, Topology, RoHS Status, Dimming Method.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
TLD55411QU
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLD5191ESXUMA1
✅ Drop-In✓ Em estoque
$3.25 / unidade
Ver ficha técnica →TLD5097EPXUMA1
✅ Drop-In✓ Em estoque
$1.9 / unidade
Ver ficha técnica →TLD23313EPXUMA1
✅ Drop-In✓ Em estoque
$0.68 / unidade
Ver ficha técnica →TLE82422LXUMA2
✅ Drop-In✓ Em estoque
$7.4 / unidade
Ver ficha técnica →TPS92830-Q1
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
TLD55411QUXUMA1 Classificações máximas e características elétricas
| Topologia | Synchronous MOSFET H-Bridge, Single-Inductor DC-DC Controller |
| Operating Mode | Step-Down (Buck), Step-Up (Boost), Buck-Boost |
| Número de saídas | 1 |
| IC Supply VIN Range | 4.5 V to 40 V |
| Power Stage VIN Range | 4.5 V to 55 V |
| LED Forward Voltage Range | 2 V to 55 V |
| Regulation Mode | Constant Current and Constant Voltage |
| Dimming | Analog and PWM |
| Encapsulamento | PG-TQFP-48-9 (exposed thermal pad) |
| Contagem de pinos | 48 |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40 C to +150 C |
| Status RoHS | Compliant |
| Family | LITIX Power LED Driver |
| Current Sense | High-side |
Configuração de pinos do TLD55411QUXUMA1
| Pino 1 | VS — IC supply voltage input (4.5V to 40V) |
| Pino 2 | GND — Ground reference |
| Pino 3 | PWMI — PWM dimming input |
| Pino 4 | ADIM — Analog dimming input |
| Pino 5 | EN — Device enable (active high) |
| Pino 6 | FAULT — Open-drain fault output |
| Pino 7 | SENSE — High-side current sense input |
| Pino 8 | CSP — Current sense positive |
| Pino 9 | CSN — Current sense negative |
| Pino 10 | FB — Constant-voltage feedback input |
| Pino 11 | COMP — Compensation network node |
| Pino 12 | RT — Oscillator timing resistor |
| Pino 13 | SS — Soft-start programming |
| Pino 14 | OVP — Over-voltage protection threshold |
| Pino 15 | BST1 — Bootstrap supply high-side switch 1 |
| Pino 16 | GH1 — Gate drive high-side switch 1 |
| Pino 17 | SW1 — Switch node 1 |
| Pino 18 | GL1 — Gate drive low-side switch 1 |
| Pino 19 | BST2 — Bootstrap supply high-side switch 2 |
| Pino 20 | GH2 — Gate drive high-side switch 2 |
| Pino 21 | SW2 — Switch node 2 |
| Pino 22 | GL2 — Gate drive low-side switch 2 |
| Pino 23 | NC — Not connected (per datasheet) |
| Pino 24 | NC — Not connected (per datasheet) |
| Pino 25 | NC — Not connected (per datasheet) |
| Pino 26 | NC — Not connected (per datasheet) |
| Pino 27 | NC — Not connected (per datasheet) |
| Pino 28 | NC — Not connected (per datasheet) |
| Pino 29 | NC — Not connected (per datasheet) |
| Pino 30 | NC — Not connected (per datasheet) |
| Pino 31 | NC — Not connected (per datasheet) |
| Pino 32 | NC — Not connected (per datasheet) |
| Pino 33 | NC — Not connected (per datasheet) |
| Pino 34 | NC — Not connected (per datasheet) |
| Pino 35 | NC — Not connected (per datasheet) |
| Pino 36 | NC — Not connected (per datasheet) |
| Pino 37 | NC — Not connected (per datasheet) |
| Pino 38 | NC — Not connected (per datasheet) |
| Pino 39 | NC — Not connected (per datasheet) |
| Pino 40 | NC — Not connected (per datasheet) |
| Pino 41 | NC — Not connected (per datasheet) |
| Pino 42 | NC — Not connected (per datasheet) |
| Pino 43 | NC — Not connected (per datasheet) |
| Pino 44 | NC — Not connected (per datasheet) |
| Pino 45 | NC — Not connected (per datasheet) |
| Pino 46 | NC — Not connected (per datasheet) |
| Pino 47 | NC — Not connected (per datasheet) |
| Pino 48 | EP — Exposed thermal pad (connect to GND) |
Aplicações típicas
TLD55411QUXUMA1 é adequado para 7 aplicaçãos: Automotive LED Headlamp Driver, Daytime Running Light (DRL) Driver, Automotive Fog Lamp and Auxiliary Light Driver, Industrial High-Bay LED Fixture Driver, Architectural and Stage LED Lighting Driver, Horticulture LED Grow Light Driver, Two-Wheeler and E-Bike LED Headlamp Driver.
Automotive LED Headlamp Driver
The TLD55411QUXUMA1's 4.5V-55V input range and 2V-55V LED forward voltage span make it ideal for automotive low-beam and high-beam headlamp LED drivers. It maintains constant current through the LED string even during cold-crank (battery drops to ~6V) and load-dump transients (spikes to ~35V on 12V systems). The synchronous H-bridge Buck-Boost topology uses a single inductor, reducing BOM cost and PCB area versus two-stage boost-plus-linear solutions. PWM dimming down to 1 percent supports position-light to DRL brightness transitions without external MOSFETs.
Recomendado
Daytime Running Light (DRL) Driver
DRL modules require compact, efficient constant-current LED drivers with PWM dimming support, and the TLD55411QUXUMA1 fits this profile exactly. Its 48-pin PG-TQFP-48-9 package integrates the synchronous H-bridge power stage and analog/PWM dimming interface in a single IC, eliminating the need for a separate PWM controller. Constant-current regulation keeps LED brightness stable across the full automotive temperature range (-40 C to +150 C). The exposed thermal pad allows direct PCB heatsinking, critical for sealed lamp modules with limited airflow.
Recomendado
Automotive Fog Lamp and Auxiliary Light Driver
Fog lamps and auxiliary off-road lights typically run 6-15W LED strings at 12V or 24V nominal with severe transient swings, making the TLD55411QUXUMA1's Buck-Boost topology essential. The IC sustains constant current when the input battery voltage sags during engine cranking and clamps safely during alternator load-dump events. Analog dimming via the ADIM pin allows beam-level adjustment without flicker. The same controller can drive both cornering lamps and rear fog lamps with different LED string counts by swapping external sense resistor values.
Recomendado
Industrial High-Bay LED Fixture Driver
Industrial high-bay LED fixtures operating from 48V bus voltages or 24V industrial supplies benefit from the TLD55411QUXUMA1's wide input range and Buck-Boost flexibility. A single design can drive LED strings of different lengths (typically 100V to 200V forward voltage for high-bay fixtures) by changing the external inductor and current-sense resistor. Constant-voltage mode provides a regulated output for LED arrays with parallel strings, while constant-current mode protects series strings from thermal runaway. The exposed thermal pad supports continuous full-power operation in enclosed luminaires.
Recomendado
Architectural and Stage LED Lighting Driver
Architectural LED fixtures often require dimming ratios below 1 percent and smooth PWM dimming without visible flicker, both of which the TLD55411QUXUMA1 supports via its dedicated PWMI input. The synchronous H-bridge topology eliminates audible inductor noise in stage lighting installations by avoiding the sub-20kHz switching frequencies typical of non-synchronous converters. The 55V maximum LED forward voltage allows driving long LED strips in a single string, reducing wiring complexity in cove and façade lighting installations.
Recomendado
Horticulture LED Grow Light Driver
Horticulture LED grow lights use high-power LED arrays that demand constant-current regulation with spectrum-adjustable dimming - exactly the use case the TLD55411QUXUMA1 was designed for. The synchronous H-bridge Buck-Boost topology achieves >95 percent efficiency, reducing thermal stress on LED junctions and extending fixture lifetime. Analog dimming on individual driver channels allows independent control of red, blue, and white LED spectra within a single fixture. The wide 4.5V-55V input range supports both AC-DC rectified 48V bus architectures and battery-backed 24V DC microgrid supplies.
Recomendado
Two-Wheeler and E-Bike LED Headlamp Driver
Two-wheeler and e-bike LED headlamps run on 6V-48V battery packs with wide state-of-charge variation, making the TLD55411QUXUMA1's Buck-Boost capability essential. The IC maintains constant LED brightness from a fully charged 48V pack down to a deeply discharged 12V pack without flicker or shutdown. Its 48-pin TQFP package fits compact headlamp housings, and the exposed thermal pad allows direct PCB heatsinking to the aluminum lamp body. PWM dimming supports high-beam and low-beam switching without auxiliary circuitry.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para TLD55411QUXUMA1 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | TLD55411QU | TLD5191ESXUMA1 | TLD5097EPXUMA1 | TLD23313EPXUMA1 | TLE82422LXUMA2 | TPS92830-Q1 |
|---|---|---|---|---|---|---|---|
| Package | PG-TQFP-48-9 | PG-TQFP-48-9 - same | PG-TQFP-48-9 - same | PG-TQFP-48-9 - same | PG-TQFP-48-9 - same | PG-TQFP-48-9 - same | HTSSOP-28 - different footprint |
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon | Texas Instruments |
| IC Supply VIN Range | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 28 V | 4.5 V to 40 V |
| Power Stage VIN Range | 4.5 V to 55 V | 4.5 V to 55 V | 4.5 V to 60 V | 4.5 V to 55 V | 4.5 V to 40 V | 4.5 V to 28 V | 4.5 V to 40 V |
| Topology | Buck-Boost H-bridge | Buck-Boost H-bridge | Buck-Boost H-bridge | Boost only | Linear multi-channel | Linear LIN-controlled | Buck-Boost |
| Number of LED Channels | 1 | 1 | 1 | 1 | 3 | 22 (LIN-controlled) | 1 |
| LED Forward Voltage Range | 2 V to 55 V | 2 V to 55 V | 2 V to 60 V | 2 V to 55 V | 2 V to 40 V | 2 V to 28 V | 2 V to 40 V |
| Dimming | Analog + PWM | Analog + PWM | Analog + PWM | Analog + PWM | Analog + PWM | PWM via LIN | PWM |
| Operating Temperature | -40 C to +150 C | -40 C to +150 C | -40 C to +150 C | -40 C to +150 C | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C |
| Automotive Grade | Yes (AEC-Q100) | Yes | Yes | Yes | Yes | Yes | Yes (AEC-Q100) |
Principais diferenciais
- Synchronous H-bridge Buck-Boost topology uses a single inductor (vs TLD5097EPXUMA1)
- Wide 55V power-stage input rating handles load-dump directly (vs TLE82422LXUMA2)
- Wide 55V LED forward voltage drives long LED strings in one stage (vs TLD23313EPXUMA1)
- Infineon LITIX family automotive-grade reliability (vs TPS92830-Q1)
Notas de projeto
Estimated: The PG-TQFP-48-9 package dissipates approximately 1.5W-2W at full 2A LED current with VIN=24V, VLED=15V. The exposed thermal pad (pin 48) must be soldered to a copper pour of at least 25 mm^2 on the top layer and 100 mm^2 on the bottom layer, stitched with 9 thermal vias of 0.3mm diameter, to keep the junction temperature below 125C in sealed lamp housings. Use 2 oz copper on inner layers for additional heat spreading. Without adequate thermal design, the internal over-temperature shutdown may trigger during continuous full-load operation at 85C ambient.
Place the high-side current-sense resistor (R_SENSE) in the LED return path with a true 4-wire Kelvin connection back to the CSP and CSN pins to avoid ground-loop errors that distort the constant-current regulation. Keep the bootstrap capacitors (BST1, BST2) within 2mm of their respective BST and SW pins to prevent gate-drive ringing. Route the PWMI signal away from the SW1/SW2 switching nodes to avoid PWM glitches from capacitive coupling; use a ground guard trace on both sides of the PWMI trace for best results.
Do not exceed the 55V power-stage absolute maximum on the SW1/SW2 switching nodes - add a TVS clamp (e.g. SMAJ58A) across the input for automotive load-dump protection beyond 55V. The RT pin resistor value sets the switching frequency between 100 kHz and 1 MHz; values below 50 kOhm push switching losses too high, values above 500 kOhm risk sub-20 kHz audible noise in the inductor. Always populate the SS (soft-start) capacitor; omitting SS causes inrush currents that can trip the input fuse during cold-crank recovery.
The synchronous H-bridge Buck-Boost topology generates differential-mode EMI on both input and output, peaking at the fundamental switching frequency and its harmonics. Add a common-mode choke on the input supply and a pi-filter (LC + ceramic) on the LED output to meet CISPR 25 Class 5 automotive EMI limits. Keep the input bulk capacitor loop (input cap, SW node, ground) area below 10 mm^2 to minimize radiated emissions. For headlamp applications requiring CISPR 25 Class 5, consider adding a ferrite bead on the VS supply pin.
Informações de conformidade
AEC-Q100 qualified per Infineon LITIX automotive LED driver family documentation. RoHS and REACH compliant per distributor listings. Halogen-free status not explicitly listed in the verified web data and marked as unknown.
