Z86C9116VSC - 8-Bit 16MHz ROMless MCU | Zilog
N.º da peça: Z86C9116VSC ✓ AtivoZ86C9116VSC Visão geral
A ROMless microcontroller is a semiconductor that executes application code from external memory instead of storing its program in an internal ROM. Within the embedded-control hierarchy, the Z86C9116VSC belongs to the 8-bit microcontroller class, where deterministic instruction execution and a broad peripheral set can provide an economical alternative to more complex 16- or 32-bit processors. Its Z8 architecture combines the processor core with embedded control peripherals in one integrated circuit.
The principal device characteristics are a 16 MHz maximum clock frequency, 236 bytes of internal data RAM, and 24 general-purpose I/O pins. Because the MCU is ROMless, the system designer must connect external program memory and also confirm the required address, data, and control signals in the application schematic. The integrated UART/USART supports serial communication, while the internal oscillator reduces the number of external clock components normally needed for basic controller designs.
The Z86C9116VSC is assembled in a 44-terminal PLCC package designated QCCJ. Its square package body and J-bend leads are intended for surface mounting, allowing the device to be placed on a PCB without through-hole insertion. The commercial temperature designation identifies its intended operating class, while the VSG, VEC, VEG, and AEG family variants provide different temperature or grade options for design portfolios that require controlled PCB migration.
Typical applications include industrial control panels, serial interface adapters, keypad and display controllers, instrumentation, appliance controllers, and embedded communications modules. The 24 available I/O lines support discrete sensors, switches, indicators, and peripheral control, while the UART/USART provides a practical path to a host processor, display, modem, or service interface.
PCB design should begin with the manufacturer pin-description and memory-interface tables. Because the device has no internal program ROM, external memory address width, chip-select behavior, read timing, and write-control requirements must be resolved before layout. Place decoupling and clock-support components according to the circuit guidelines in the manufacturer documentation, and preserve the PLCC land pattern when comparing temperature-grade replacements.
This page combines the confirmed Z86C9116VSC device characteristics, same-footprint Z8 alternatives, parameter comparisons, and practical migration guidance. It also separates commercial sourcing questions from engineering selection so engineers can identify a qualified replacement and request current availability through the XAIPART Request a Quote form.
Alternativas drop-in para Z86C9116VSC — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com Z86C9116VSC (mesmo formato e footprint) — diferindo em Mounting Type, Program Memory, Pin Count, I/O Port Count, Maximum Clock Frequency.
Z86C9116VSG
✅ Drop-InConsulte o preço
Ver ficha técnica →Z86C9116VEC
✅ Drop-InConsulte o preço
Z86C9116VEG
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →Z86C9116AEG
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →Z86C9325VSC
✅ Drop-InConsulte o preço
Ver ficha técnica →Z86C9116VSC Classificações máximas e características elétricas
| Product Type | 8-bit ROMless microcontroller |
| Architecture | Z8 |
| CPU Bit Width | 8 bit |
| Frequência máxima de clock | 16 MHz |
| Program Memory | ROMless; external memory required |
| Internal RAM | 236 x 8 bit (236 bytes) |
| General-Purpose I/O | 24 pins |
| Serial Interface | 1 UART/USART interface |
| Clock Source | Internal oscillator |
| Encapsulamento | PLCC-44 (QCCJ) |
| Contagem de pinos | 44 terminals |
| Package Body Shape | Square |
| Terminal Form | J-bend lead |
| Tipo de montagem | Surface mount |
| Temperature Grade | Commercial |
Guia de Configuração de Pinos do Z86C9116VSC square
Configuração de pinos para Z86C9116VSC (pacote square). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para Z86C9116VSC.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
Z86C9116VSC é adequado para 6 aplicaçãos: Serial Interface Adapter, Industrial Control Panel, Appliance Controller, Instrumentation Front End, Embedded Communications Module, Keypad and Display Controller.
Serial Interface Adapter
The Z86C9116VSC fits a compact serial adapter because its 16 MHz Z8 core, UART/USART, 24 I/O pins, and internal oscillator support communication and control without a separate clock crystal. External program memory is required for the ROMless MCU, while its 236 bytes of RAM can hold protocol state, counters, and short buffers. The 44-pin PLCC package also provides enough physical connections for control signals, status indicators, and interface transceivers. Before layout, verify the exact peripheral multiplexing, external-memory bus requirements, and timing from the manufacturer pin-description tables.
Recomendado
Industrial Control Panel
The Z86C9116VSC can coordinate an industrial control panel with 24 I/O pins for switches, lamps, relays, and status inputs while its UART/USART links the panel to a higher-level controller. Its 16 MHz operating rate is suitable for responsive supervisory logic, and the ROMless architecture allows firmware to reside in external memory selected for the required code size. The commercial temperature grade must be checked against the intended enclosure environment. PCB planning should separate switching-node wiring from sensitive signal paths and confirm the PLCC land pattern against the selected grade.
Recomendado
Appliance Controller
The Z86C9116VSC is well suited to appliance control because its 24 I/O pins can operate displays, keys, indicators, and discrete actuators while the UART/USART supports an external control module. The 236-byte internal RAM can support short task state and communication buffers, and external program memory provides flexibility when firmware size changes across appliance models. Because the MCU is ROMless, the design must include a defined program-memory and firmware-update strategy. Use the internal oscillator only after confirming frequency tolerance requirements, and verify the commercial temperature specification for the appliance installation location.
Recomendado
Instrumentation Front End
The Z86C9116VSC can provide supervisory control for instrumentation when a compact 8-bit processor, external program storage, and 24 I/O lines are sufficient. The UART/USART can connect measurement electronics to a host or display, while the internal oscillator supports a cost-conscious control platform. Its 236 bytes of RAM requires disciplined buffer sizing, so applications should avoid placing large datasets on-chip. The commercial temperature grade is suitable only within its specified operating limits. Use the manufacturer memory-interface and pin multiplexing information when assigning external sensors and data-acquisition components.
Recomendado
Embedded Communications Module
The Z86C9116VSC can act as the supervisory controller in an embedded communications module where a UART/USART, 24 I/O pins, and a 16 MHz processor are adequate. External program memory makes the module adaptable to different protocol stacks, while 236 bytes of RAM provides limited working storage for framing, status, and counters. A network-capable companion may handle higher protocol layers, allowing the Z8 MCU to manage local I/O and configuration. Validate buffer requirements, communication timing, and temperature conditions before production release, and preserve the documented 44-pin PLCC footprint.
Recomendado
Keypad and Display Controller
The Z86C9116VSC can scan a keypad and manage display-control signals through its 24 I/O pins while using the UART/USART to receive display commands or report user input. The 16 MHz Z8 core provides sufficient control bandwidth for common matrix-keypad and indicator arrangements, and the internal oscillator can reduce external clock-component count. Since only 236 bytes of RAM are available, scan buffers and message formatting should be compact. The ROMless design requires external program storage, and every multifunction terminal must be assigned using the manufacturer pin table before the PCB is released.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para Z86C9116VSC — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | Z86C9116VSG | Z86C9116VEC | Z86C9116VEG | Z86C9116AEG | Z86C9325VSC |
|---|---|---|---|---|---|---|
| Brand | Zilog | Zilog | Zilog | Zilog | Zilog | Zilog |
| Package | PLCC-44 (QCCJ) | PLCC-44 (QCCJ) | PLCC-44 (QCCJ) | PLCC-44 (QCCJ) | PLCC-44 (QCCJ) | PLCC-44 |
| Maximum Clock Frequency | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 16 MHz | 25 MHz |
| CPU Architecture | Z8, 8-bit | Z8, 8-bit | Z8, 8-bit | Z8, 8-bit | Z8, 8-bit | Z8, 8-bit |
| Temperature Grade | Commercial | Grade-specific; verify with manufacturer documentation | Grade-specific; verify with manufacturer documentation | Grade-specific; verify with manufacturer documentation | Grade-specific; verify with manufacturer documentation | Commercial |
Principais diferenciais
- Directly preserves the 16 MHz commercial-grade device specification (vs Z86C9116VSG)
- Maintains the established 236-byte memory and 24-I/O configuration (vs Z86C9325VSC)
- Uses the same 44-terminal PLCC family footprint for controlled PCB migration (vs Z86C9116VEC)
- Supports serial communications without requiring a separate external oscillator (vs Z86C9116AEG)
Notas de projeto
Do not treat a matching PLCC footprint as proof that two Z86C9116 ordering codes are interchangeable. Compare the manufacturer specifications for supply voltage, temperature range, clock timing, reset behavior, UART features, and external-memory control signals. In particular, the VSC, VSG, VEC, VEG, and AEG suffixes identify different grade-specific variants. Update the schematic and procurement specification together, and verify that the selected replacement remains within the product's intended environmental and qualification requirements.
Design the memory interface before fixing the PLCC routing. The ROMless architecture requires external program memory, so address lines, data lines, chip-select, read-control, and write-control signals must be assigned according to the manufacturer pin table. Check source and destination timing, including any required wait states, and route the memory bus away from switching power stages and high-current actuator traces. Because a 44-pin PLCC is not represented by the selected package-diagram library, verify its land pattern directly against the manufacturer mechanical drawing rather than relying on a generic package image.
Separate UART, sensor inputs, and external-memory signals from relay, motor, and mains-derived switching nodes. Keep the MCU supply decoupling path short and place the local capacitor close to the appropriate power terminal. Use a common, low-impedance ground strategy, but return high-current actuator currents directly to the supply or chassis reference as appropriate. Confirm oscillator and reset trace integrity using the manufacturer layout guidance, particularly if the internal oscillator is used for UART timing or timing-sensitive control.
The available component records do not provide a complete operating-voltage table, so the supply rail must be selected from the manufacturer specifications rather than inferred from the 16 MHz clock rating. Include adequate local decoupling for the MCU and external memory, and account for the combined dynamic and static current of both devices when sizing the supply. If the Z8 MCU controls power switches, keep its supply regulation independent of relay or motor transients. Validate startup, brownout, and reset behavior across the full input range and temperature class.
Informações de conformidade
The available component listings do not provide a definitive RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration. AEC-Q100 is not applicable to this commercial microcontroller as identified.