Интегральные схемы

PIC16F1614-I/ML

PIC16F1614-I/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip

The Microchip Technology PIC16F1614-I/ML is an 8-bit RISC Flash microcontroller from the PIC16 (L)F161x family, featuring 7 KB of program Flash, 512 bytes of RAM, and 32 MHz maximum CPU clock, housed in a 16-pin QFN (4x4 mm) package with an exposed thermal pad. An 8-bit microcontroller (MCU) is a single-chip computer with an 8-bit data path, integrating a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and on-chip peripherals such as timers, ADC, communication interfaces, and I/O. The PIC16F1614 belongs to the eXtreme Low Power (XLP) PIC16F family from Microchip, targeting compact, low-power embedded control with motor-control-oriented peripherals such as CCP, 24-bit Signal Measurement Timer (SMT), Zero-Cross Detect, and Configurable Logic Cells (CLC) — features that place this MCU in the broader category of microcontrollers -> embedded controllers -> semiconductors. The PIC16F1614 integrates a 10-bit ADC with computation (ADC2), two PWM channels, two comparators, two CLCs, and a wide 1.8 V to 5.5 V operating range that supports 2.5 V / 3.3 V / 5 V systems. According to the Microchip product page, the device delivers on-chip features unique to embedded control of small motors and general-purpose applications in 8 / 14 / 20-pin variants, with the I/ML package representing the 14/16-pin QFN option. Peripherals communicate through PPS (Peripheral Pin Select) on most pins, simplifying PCB routing in compact designs. The core uses Microchip's enhanced mid-range 8-bit CPU with hardware stack and 14-bit instruction word, executing most instructions in a single cycle. Internal oscillator options (HFINTOSC up to 32 MHz with PLL, LFINTOSC 31 kHz) reduce external component count and enable rapid prototyping. The device's XLP features — nanoWatt XLP sleep currents below 50 nA typical, IDLE/DOZE current management, and ultra-low-power wake — make it well-suited to battery-powered nodes that spend most of their life in sleep. Typical applications include BLDC / brushed-DC small-motor control, LED lighting drivers with zero-cross dimming, fan and pump control, sensor-interface front-ends with on-chip signal conditioning, and general-purpose 8-bit embedded control where footprint, BOM count, and power budget dominate the BOM. The 4x4 mm QFN fits compact PCBs in space-constrained appliances and IoT edge nodes. When designing with this device, allocate the PPS remap early in firmware planning because most digital peripherals can be routed to multiple pins. Always check that the chosen ADC channel and PWM output do not collide on the same physical pin, and provide a 0.1 µF + bulk decoupling pair adjacent to the VDD pin. This page synthesizes distributor pricing, drop-in QFN-16 alternatives from Microchip's PIC16 family, application guidance, and practical design notes that are not present on the bare manufacturer product page.

Запрос цены Контакты

PIC16F1614-I/P

PIC16F1614-I/P - 8-Bit MCU, 7KB Flash, 32MHz, 14-PDIP | Microchip

The Microchip Technology PIC16F1614-I/P is an 8-bit RISC microcontroller from the PIC16F161X family, offering 7 KB (4K x 14 words) of Flash program memory and 512 bytes of SRAM in a 14-pin PDIP (0.300 inch, 7.62 mm) through-hole package. The device operates up to 32 MHz instruction clock, delivers 10-bit ADC with up to 8 channels, and supports Core Independent Peripherals including Configurable Logic Cells (CLC), Zero-Cross Detector (ZCD), 24-bit Signal Measurement Timer (SMT), and Complementary Waveform Generator (CWG) for embedded motor and lighting control. It operates from 2.3V to 5.5V with eXtreme Low Power (XLP) Sleep currents in the nanoamp range. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, RAM, and peripheral interfaces. The PIC16F1614 belongs to the 8-bit RISC MCU class, where each instruction executes in one instruction cycle, providing deterministic timing critical for real-time control. Within the broader taxonomy, it sits in the 8-bit microcontroller category under microcontrollers and integrated circuits. It is pin-compatible with PIC16F1613 in the same package, enabling design scalability with shared PCB layouts. Key differentiating features include four Configurable Logic Cells that replace external discrete glue logic, a 24-bit SMT for precise time and pulse measurement, a Zero-Cross Detector for AC line synchronization, and a Complementary Waveform Generator producing complementary PWM outputs with programmable dead-band for half-bridge motor drive. These features reduce external component count and BOM cost in motor control, lighting ballast, and digital power conversion applications. Technically, the PIC16F1614 uses Microchip's enhanced mid-range core with a hardware multiply and 16-level stack. Memory includes 7 KB self-programmable Flash, 512 B SRAM, and 256 B EEPROM. Peripherals include up to 8x 10-bit ADC channels, two PWM modules (10-bit), two CCP modules, two USART, two SPI, two I2C, and up to 12 I/O pins with interrupt-on-change. This part fits low-power fan control, sensor interfacing, BLDC motor commutation, AC phase control, LED lighting, and IoT endpoint nodes. For battery-powered designs, XLP Sleep mode with nA-level current enables multi-year coin-cell operation in sensor beacons. The 14-PDIP package eases prototyping and hobbyist use. When designing, prioritize PCB trace layout for ADC analog inputs (guard ring, ground plane separation), and use the CWG module for half-bridge gate drive rather than a discrete driver when possible. Always validate PWM frequency against MOSFET/IGBT switching losses. This page synthesizes the Microchip PIC16F1614-I/P datasheet, real-time distributor pricing from DigiKey/Mouser/LCSC, drop-in same-family alternatives from the Site MPN list, and practical design notes not present in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1614-I/SL

PIC16F1614-I/SL - 8-Bit 32MHz MCU 7KB Flash | Microchip

The Microchip Technology PIC16F1614-I/SL is an 8-bit PIC® XLP™ flash microcontroller featuring a 32MHz CPU, 7KB (4K x 14) program flash, 512 bytes SRAM, and a 14-pin SOIC package. It integrates a 10-bit ADC, Configurable Logic Cell (CLC), Complementary Output Generator (COG), Signal Measurement Timer (SMT), Zero-Cross Detect (ZCD), and CCP peripherals designed for embedded control of small motors and general-purpose applications. An 8-bit flash microcontroller (MCU) is a small, self-contained computer-on-a-chip that integrates an 8-bit CPU, non-volatile flash program memory, volatile SRAM, and a configurable peripheral set into a single IC. Within the broader hierarchy, 8-bit MCUs sit below 16-bit and 32-bit MCUs in computational throughput, but excel in deterministic real-time control, ultra-low power operation (the PIC16 XLP family is engineered for nanoWatt standby currents), and BOM cost minimization. They are the dominant choice for sensor nodes, motor control loops, user-interface handling, and battery-powered devices where code density and predictability outweigh raw MIPS. Key features include 32MHz internal oscillator operation, 10-bit ADC with computation, 24-bit Signal Measurement Timer (SMT) for precise time-of-flight and edge counting, Zero-Cross Detect for AC line synchronization, Configurable Logic Cell, Complementary Output Generator, and nanoWatt XLP power management. The 14-pin SOIC (SL) package is a JEDEC-standard 3.90mm-wide surface-mount footprint that is breadboard-friendly and reflow-solderable, suitable for both prototyping and high-volume production. The PIC16F1614 uses a 14-bit modified Harvard RISC architecture with a 16-level hardware stack, single-cycle hardware multiply, and C-compiler-friendly instruction set. The XLP nanoWatt technology delivers sub-microamp sleep modes enabling multi-year battery life in IoT edge nodes, while the integrated SMT 24-bit timer and CLC permit hardware-level signal processing without CPU intervention, freeing the core for system-level logic. Typical applications include small DC and stepper motor control (BLDC, brushed DC), fan control, TRIAC dimming with ZCD, sensor signal conditioning, appliance controls, LED lighting drivers, IoT edge nodes, and general-purpose embedded control. The industrial-grade -40C to +85C temperature range supports factory and outdoor deployments. When designing with this device, allocate sufficient code-space headroom (5-10% free flash for field updates), provide adequate Vdd decoupling per the datasheet reference circuit, and verify that the chosen CCP/COG/SMT peripheral combination fits the application timeline within the 32MHz instruction budget. This page synthesizes distributor pricing from DigiKey/Mouser/LCSC, parametric drop-in alternatives in the same SOIC-14 footprint, and practical design notes that go beyond what is reprinted on standard catalog pages.

Запрос цены Контакты

PIC16F1614-I/ST

PIC16F1614-I/ST - 8-Bit MCU, 7KB Flash, 32MHz, TSSOP-14 | Microchip

The Microchip Technology PIC16F1614-I/ST is an 8-bit Flash microcontroller from the PIC16F161X family, integrating 7KB of program memory (4K x 14-bit words), 512 bytes of RAM, and a 32 MHz internal oscillator in a 14-pin TSSOP surface-mount package. It combines a 10-bit ADC, Capture/Compare/PWM (CCP), a 24-bit Signal Measurement Timer (SMT), Zero-Cross Detect, and a math accelerator, providing on-chip resources for embedded control of small motors and general-purpose applications. The -I/ST suffix designates the industrial temperature grade (-40C to +85C) and TSSOP-14 packaging. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash or ROM), volatile data memory (RAM), and integrated peripherals such as timers, ADCs, and communication interfaces. Within the broader taxonomy, the PIC16F1614 sits in the 8-bit microcontroller class (PIC16 -> 8-bit PIC MCU -> microcontroller -> embedded processor -> semiconductor). It uses Microchip's enhanced mid-range core with a 14-bit instruction word, balancing code density with deterministic interrupt latency for real-time control. Key features include 7KB self-programmable Flash, multiple PWM/CCP channels for motor and LED control, a 24-bit SMT capable of precise time-of-flight or frequency measurements, Zero-Cross Detect for AC-line-synchronized switching, and Configurable Logic Cells (CLC) for hardware customization. The XLP (eXtreme Low Power) designation places sleep current in the nanoampere range, making the part attractive for battery-operated sensor nodes. The architecture uses a Harvard-style bus with separate program and data paths, a 16-level hardware stack, and direct LED drive capability on selected pins. The device operates from 2.5V to 5.5V across the industrial thermal range, and integrates common sensor and actuator interfaces without external glue logic. Typical applications include small brushed-DC and stepper motor control, ceiling-fan and HVAC line-voltage control, LED lighting drivers, sensor signal conditioning, and general-purpose embedded control. Compared with discrete logic designs, the PIC16F1614 reduces BOM count and PCB area by integrating ADC, PWM, and commutation timers on one die. When designing with this MCU, place a 100 nF decoupling capacitor close to VDD with a bulk capacitor nearby, and keep the ICSP/PGD-PGC pins accessible for in-circuit programming. Program CONFIG words to match the chosen oscillator, watchdog timer, and code-protect settings before first use. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

PIC16F1614T-I/SL

PIC16F1614T-I/SL - 8-bit MCU, 7KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F1614T-I/SL is an 8-bit PIC microcontroller from the PIC16F161X family with 7KB Flash program memory, 512 bytes RAM, and 32 MHz internal oscillator, housed in a 14-pin SOIC (SL) package. The device integrates a 10-bit ADC, Capture/Compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection (ZCD), and peripheral pin select (PPS) for flexible mixed-signal control in compact form factors. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and configurable peripherals. The PIC16F1614 uses Microchip's enhanced mid-range 8-bit core running up to 32 MHz (8 MIPS) with a single-cycle instruction pipeline and 14-bit instruction word. The -I suffix indicates the industrial temperature range of -40C to +85C, while T denotes tape-and-reel packaging, and SL identifies the 14-pin SOIC outline. Key features include 10-bit A/D with computation, 5-bit DAC, 8-bit/16-bit timers, angular timer (24-bit SMT), complementary waveform generator, hardware limit timer, configurable logic cell (CLC), math accelerator, and an HF 32 MHz internal oscillator with +/- 2% accuracy. The XLP (eXtreme Low Power) variant retains active-mode current under 100 uA/MHz and sleep currents in the nA range, enabling battery-friendly duty-cycled designs. The PIC16F161X architecture delivers CIP (Core Independent Peripherals) such as CLC and SMT that offload state-machine and timing tasks from the CPU, allowing closed-loop fan control, lighting fade, and small-motor trapezoidal commutation without firmware overhead. With 7KB Flash (4K x 14 words) and 512 bytes RAM, the device targets cost-sensitive 8-bit applications that still need modern analog integration. Typical applications include small DC and stepper motor control loops, fan and pump RPM regulation, LED lighting controllers with dimming, household appliances, and general-purpose mixed-signal embedded control. The 14-pin SOIC footprint also simplifies migration from older PIC16F1xxx designs. Industrial-grade temperature and on-chip CIP make this MCU a strong fit for appliance and IoT edge nodes. Design tip: ensure the MCLR pin has the recommended 10 kohm pull-up and a 0.1 uF bypass capacitor on VDD within 5 mm of the pin. The ZCD and CCP peripherals are configured independently via PPS, so pin mapping must be finalized before firmware lock-in. This page synthesizes distributor pricing, drop-in alternative MPNs from the same Microchip PIC16F161X family, and practical design notes not aggregated in the manufacturer datasheet, helping procurement and embedded engineers evaluate the PIC16F1614T-I/SL against competing 14-pin 8-bit MCU options.

Запрос цены Контакты

PIC16F1615-E/ML

PIC16F1615-E/ML - 8-bit MCU, 14KB Flash, 32MHz, QFN-16 | Microchip

The Microchip Technology PIC16F1615-E/ML is an 8-bit PIC microcontroller featuring 14KB Flash program memory, 1KB RAM, and a 32MHz internal oscillator, housed in a 16-pin QFN (ML) package with extended -40C to +125C operating temperature range. The device integrates a 10-bit ADC, Capture/Compare/PWM (CCP), 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, and Complementary Waveform Generator (CWG), making it well-suited for closed-loop control of small motors, lighting, and general-purpose embedded applications. An 8-bit microcontroller (MCU) is a compact processor core that integrates CPU, RAM, program memory, and peripherals on a single die. Within the system hierarchy, an MCU sits below microprocessors (MPUs) but above discrete logic, providing programmable I/O, timing, and analog functions for embedded control. The PIC16F1615 belongs to Microchip's PIC16F1xxx enhanced mid-range family, which balances code density, peripheral richness, and ultra-low-power (XLP) operation for cost-sensitive industrial and consumer designs. Key features include 14KB self-programmable Flash, 1KB SRAM, 256B EEPROM, 10-bit ADC with computation (ADC2), 8-bit DAC, configurable logic cells (CLC), and Peripheral Pin Select (PPS). The integrated 32MHz high-speed oscillator eliminates external crystals in many designs. Built-in Core Independent Peripherals (CIPs) such as the CWG and SMT allow complex waveforms and precise time measurements without CPU intervention, reducing firmware complexity and power consumption. The PIC16F1615-E/ML uses a 14-bit instruction set with 8-bit data path and a modified Harvard architecture. Its nanoWatt XLP technology enables active currents under 50 uA/MHz and sleep currents in the nanoamp range, enabling battery-powered and energy-harvesting designs. The device supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD) through dedicated pins, allowing rapid firmware iteration. Typical applications include small BLDC or brushed-DC motor control, LED lighting drivers, switched-mode power supply (SMPS) control, sensor signal conditioning, fan control, and home appliance user interfaces. Its combination of integrated analog, logic, and timer peripherals makes it well matched to applications that previously required multiple discrete ICs. When designing with the PIC16F1615-E/ML, ensure that VDD decoupling follows Microchip's recommended layout guidelines: a 0.1 uF ceramic capacitor placed within 4mm of each VDD/AVDD pin, plus a bulk 10 uF capacitor on the main supply rail. PPS configuration should be assigned before enabling peripherals to avoid spurious output transitions on power-up. This page synthesizes verified distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet front page.

Запрос цены Контакты

PIC16F1615-E/P

PIC16F1615-E/P - 8-Bit 32MHz 14KB Flash MCU | Microchip 14-PDIP

The Microchip Technology PIC16F1615-E/P is an 8-bit microcontroller from the PIC® XLP™ 16F family with on-chip Functional Safety (FuSa) features, delivering 32 MHz CPU performance with 14 KB (8K x 14) of FLASH program memory in a 14-pin PDIP package. Key highlights include 1 KB of RAM, a 10-bit A/D converter, configurable logic cells (CLC), CCP, 24-bit SMT timer, and Zero-Cross Detect (ZCD) peripherals tailored for embedded control of small motors and general-purpose applications. The 'E' suffix denotes the extended industrial temperature grade of -40C to +125C, and the 'P' suffix designates the through-hole 14-pin PDIP package. A microcontroller (MCU) is a single-chip computer containing a processor core, program memory (FLASH), working memory (RAM), and a rich set of programmable peripherals. The PIC16F1615 belongs to the 8-bit PIC mid-range architecture, which occupies the entry-level node in the Microchip controller hierarchy: 8-bit PIC -> PIC16 family -> PIC16F1xxx enhanced mid-range -> PIC16F161x sub-family with XLP and FuSa features. Its eXtreme Low Power (XLP) technology enables nanoWatt sleep currents suitable for battery-powered IoT nodes, and the FuSa subsystem provides hardware diagnostics for IEC 60730 Class B safety compliance. Differentiating features include 10-bit ADC with computation, complementary waveform generator (CWG), four 16-bit timers, two CCP modules, two UART, one I2C/SPI, and 12 I/O pins with interrupt-on-change. The wide operating voltage of 1.8 V to 5.5 V supports both 3.3 V and 5 V rails common in industrial sensor interfaces. Internal 32 MHz oscillator eliminates external crystals in cost-sensitive designs, while the 14-pin PDIP format simplifies through-hole prototyping on breadboards and perfboards. Functional safety features include windowed WDT, oscillator fail-safe, and CRC memory verification, making it attractive for white-good and appliance control. Typical applications include small BLDC/PMSM motor control loops, sensor signal conditioning, LED lighting controllers, battery-powered IoT endpoints, and safety-critical white goods such as washing machines and dishwashers. The combination of 14 KB FLASH and 1 KB RAM is well suited to mid-complexity state-machine firmware with light protocol stacks. The CWG and CCP peripherals support half-bridge and full-bridge drive timing for low-voltage brushed or stepper motors below 1 A. When designing with this device, allocate at least two I/O pins for ICSP programming (PGD/PGC), and reserve one I/O for the MCLR reset. The internal oscillator trim should be calibrated at production for UART timing accuracy. Decouple VDD with a 100 nF ceramic placed within 5 mm of the pin, and route analog VDD+ AVSS paths with a ferrite bead if ADC accuracy below 1 LSB is required. This page synthesizes distributor pricing, drop-in PIC16F161x family alternatives, application guidance, and PCB design notes not consolidated on the manufacturer product page.

Запрос цены Контакты

PIC16F1615-E/SL

PIC16F1615-E/SL - 8-bit MCU 14KB Flash 32MHz 14-SOIC | Microchip

The Microchip Technology PIC16F1615-E/SL is an 8-bit RISC microcontroller built around the PIC16 CPU core, delivering 32 MHz of computational performance with 14KB (8K x 14) of Flash program memory, 1 KB of RAM, and a 10-bit A/D converter. Housed in a 14-pin SOIC package and operating from 2.5 V to 5.5 V (down to 2.3 V at 16 MHz), this Functional Safety (FuSa) capable device is engineered for embedded control of small motors and general-purpose applications. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. Within the broader taxonomy, the PIC16F1615 sits in the 8-bit MCU category, which in turn belongs to the microcontroller IC family and ultimately the integrated circuits class of semiconductor devices. The 8-bit PIC architecture balances deterministic interrupt response, low power consumption, and a compact instruction set, making it ideal for cost-sensitive real-time control where 32-bit processing is unnecessary. Key features that distinguish this part include a 32 MHz internal oscillator with ±1% accuracy, Zero Cross Detection (ZCD), 24-bit Signal Measurement Timer (SMT), Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), and a Windowed Watchdog Timer (WWDT) with hardware limit timer. The integrated 10-bit ADC supports up to 12 channels with hardware Capacitive Voltage Divider (CVD) for touch sensing, and the device includes functional safety features such as CRC/Scan and a hardware Memory Built-In Self-Test (MBIST). The 14-SOIC package supports industrial operating temperatures from -40 °C to +125 °C. The PIC16F1615 uses a Harvard-architecture RISC CPU with 49 single-word instructions, executing most instructions in a single clock cycle. Its nanoWatt XLP technology delivers sleep currents in the nanoampere range, making it well suited for battery-powered designs. The peripheral integration (CLC, CWG, SMT, ZCD) replaces discrete components, reducing both BOM cost and PCB area in motor drive, lighting, and sensor-interface designs. Typical applications include small BLDC and stepper motor control, solid-state lighting with dimming and color mixing, capacitive-touch user interfaces, fan and pump control, and sensor signal conditioning. According to the manufacturer product page, the device targets embedded control applications requiring functional safety at the MCU level. When designing with the PIC16F1615, allocate the analog and digital supply pins (VDD/VSS) per the datasheet and use decoupling capacitors of 0.1 µF plus a 10 µF bulk capacitor. The -E suffix denotes the extended industrial temperature range (-40 °C to +125 °C); select the -I variant only for commercial 0-85 °C or industrial -40-85 °C ranges. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design considerations beyond the manufacturer datasheet to accelerate component selection.

Запрос цены Контакты

PIC16F1615-I/JQ

PIC16F1615-I/JQ - 8-bit 32MHz MCU, 14KB Flash, 16-UQFN | Microchip

The Microchip Technology PIC16F1615-I/JQ is an 8-bit PIC microcontroller with XLP (eXtreme Low Power) technology and Functional Safety (FuSa) features, operating at up to 32 MHz in a compact 16-pin UQFN (4x4 mm) package with exposed pad. It integrates 14 KB (8K x 14) of Flash program memory, 1 KB RAM, and a rich set of peripherals including 10-bit ADC with Computation (ADCC), Zero-Cross Detection (ZCD), 24-bit Signal Measurement Timer (SMT), Windowed Watchdog Timer (WWDT), Cyclic Redundancy Check (CRC/SCAN), Capture/Compare/PWM (CCP), and Configurable Logic Cells (CLC). A microcontroller (MCU) is an integrated circuit containing a CPU core, program memory (Flash), data memory (RAM), and on-chip peripherals such as timers, ADCs, and communication interfaces. The PIC16F1615 belongs to the 8-bit PIC16 family within Microchip's 8-bit microcontroller portfolio, which sits hierarchically under the broader PIC architecture, microcontrollers, embedded controllers, and finally the semiconductor category. The 16-pin UQFN package makes it suited for space-constrained designs where a low pin count PIC with rich analog features is required. Key features of the PIC16F1615-I/JQ include 14 KB Flash, 1 KB RAM, 256 B EEPROM, 12 I/O pins, 1.8V-5.5V wide operating voltage, internal 32 MHz oscillator, 10-bit ADCC, two CCP modules, two CLC blocks, ZCD, WWDT, CRC, and high-temperature operation up to 125 °C. The XLP designation indicates ultra-low-power Sleep currents in the nA range with active mode current below 50 µA/MHz, making it ideal for battery-powered applications. Architecturally, the PIC16F1615 uses a RISC-based 8-bit PIC core with hardware Multiply and a 14-bit instruction word. The integrated ADCC automates averaging, burst accumulation, and threshold comparisons without CPU intervention, while the 24-bit SMT enables precise time-of-flight or capacitive sensing measurements. Functional Safety (FuSa) features such as WWDT, CRC memory scan, and dedicated error peripherals support IEC 61508 SIL-2 capable systems. Typical applications include small motor control (fan, pump, BLDC), LED lighting control with ZCD-based TRIAC dimming, capacitive touch / proximity sensing via CLC + SMT, battery chargers, sensor nodes in IoT edge devices, and general-purpose industrial control with safety diagnostics. The 16-UQFN footprint suits wearables, sealed sensor modules, and miniaturized industrial nodes. When designing with this MCU, ensure the exposed pad is soldered to the PCB ground plane for thermal dissipation and electrical reference. Use MPLAB X IDE with XC8 compiler and MPLAB Code Configurator (MCC) for rapid peripheral setup. For functional safety designs, consult the FuSa user guide and the FMEDA document for failure-rate budgeting. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone, providing information gain beyond what is available on distributor product pages.

Запрос цены Контакты

PIC16F1615-I/ML

PIC16F1615-I/ML - 8-Bit 32MHz 14KB Flash MCU | Microchip

The Microchip PIC16F1615-I/ML is an 8-bit PIC microcontroller in the PIC16F161X family, featuring 14KB Flash program memory, 1KB RAM, 32MHz CPU speed, and a 10-bit ADC, housed in a 16-pin QFN (4x4 mm) package with an exposed thermal pad. It targets embedded control of small motors and general-purpose applications in low pin-count packages, and carries Microchip's PIC XLP (eXtreme Low Power) branding for battery-friendly operation. The Functional Safety (FuSa) variant adds safety-oriented peripherals useful for fault detection in closed-loop control systems. An 8-bit microcontroller is a self-contained computing device that integrates a CPU, program memory (Flash), data memory (RAM), and peripherals onto a single silicon die. The PIC16F1615 belongs to the PIC10/12/16 mid-range family, which combines a Harvard architecture with a RISC instruction set optimized for deterministic interrupt response and predictable timing. Within the broader semiconductor taxonomy, it sits as: microcontroller -> 8-bit MCU -> PIC16 mid-range -> PIC16F161X family. The XLP variants further reduce active and sleep current draw for energy-harvesting and battery-powered designs. Key features include a 32MHz internal oscillator (8 MIPS), 14KB Flash with self-programmability, 1KB RAM, 256 bytes of EEPROM, a 10-bit A/D converter with up to 8 channels, multiple PWM modules, a 24-bit Signal Measurement Timer (SMT), Zero-Cross Detection, Configurable Logic Cells (CLC), and Core Independent Peripherals (CIPs) that let hardware handle tasks without CPU intervention. The 16-QFN (4x4 mm) package gives a compact footprint with an exposed pad for thermal dissipation. Technically, the device operates from 2.3V to 5.5V, includes an 8-level hardware stack, 16 I/O pins, and supports in-circuit serial programming (ICSP) and in-circuit debugging. Peripherals like the CLC and SMT enable timer, logic, and signal-processing functions to run autonomously, freeing the CPU for application code. Typical applications include small BLDC and stepper motor control, LED lighting with dimming, sensor signal conditioning, consumer appliances, battery-powered IoT endpoints, and functional-safety subsystems. Its compact QFN-16 footprint suits space-constrained designs. When designing, ensure the exposed pad is soldered to a sufficient copper pour for thermal relief, place a 0.1uF decoupling capacitor on VDD close to the pin, and follow Microchip's errata for any silicon revision-specific behavior. This page synthesizes distributor pricing, drop-in QFN-16 alternatives from the same PIC16 family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1615-I/P

PIC16F1615-I/P - 8-Bit 32MHz MCU 14KB Flash 14-PDIP | Microchip

The Microchip Technology PIC16F1615-I/P is a low-pin-count 8-bit PIC microcontroller from the PIC® XLP™ 16F family with functional-safety (FuSa) features, delivering 32 MHz CPU performance, 14 KB of Flash program memory and 1 KB of RAM in a 14-pin PDIP through-hole package. It targets embedded control of small motors and general-purpose applications with on-chip peripherals including a 10-bit ADC, CCP, 24-bit SMT (Signal Measurement Timer), Zero Cross Detection and multiple PWM/CCP channels. A microcontroller (MCU) is an integrated circuit that combines a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a range of peripheral blocks (ADC, timers, communication ports) on a single die. Within the broader semiconductor taxonomy it sits under: microcontroller -> 8-bit microcontroller -> PIC16 family -> PIC16F161X sub-family -> power management and motor/lighting control application segment. The PIC16F1615 in particular belongs to the PIC16(L)F161X family that introduced 24-bit SMT and Zero Cross Detect for solid-state relay, TRIAC and BLDC-type control. Key features of the PIC16F1615-I/P include: 32 MHz internal oscillator, 14 KB Flash with self-programmable support, 1 KB RAM, 256 B EEPROM, 10-bit ADC with multiple channels, 5-/8-bit DAC, configurable logic cell (CLC), Complementary Waveform Generator (CWG), Zero Cross Detection (ZCD), 24-bit Signal Measurement Timer (SMT), CCP modules, EUSART, I2C/SPI, and 12 I/O pins on the 14-pin PDIP. The eXtreme Low Power (XLP) technology delivers <50 nA typical sleep current, making it suitable for battery-powered designs. The device supports a wide operating voltage of 2.5 V to 5.5 V (PIC16F1615) or 1.8 V to 3.6 V (PIC16LF1615). Architecturally, the device uses Microchip's enhanced mid-range 8-bit RISC core with a 14-bit instruction word, 8-level hardware stack and 49 instruction set, providing 16 MIPS throughput at 32 MHz. The integrated CWG and ZCD peripherals allow direct generation of complementary PWM outputs with programmable dead-band and zero-voltage switching, which removes the need for an external gate-driver in many motor/lighting designs. CIPs (Core Independent Peripherals) like CLC, NCO and SMT let signal conditioning run without CPU intervention, freeing the core for supervisory tasks. Typical applications include low-voltage motor control (BLDC, brushed DC), solid-state lighting and TRIAC dimming, sensor signal conditioning with CLC, low-power battery-powered IoT nodes, and consumer / industrial control where small pin count and FuSa-class hardware documentation are required. The PIC16F1615 family is also well-suited as a functional-safety MCU in household appliances and white goods (IEC 60730 class B support documentation is available from Microchip). When designing with this MCU, ensure the supply decoupling network uses a 100 nF ceramic capacitor within a few millimetres of the VDD pin, optionally with a bulk 10 uF tantalum or aluminium electrolytic cap on the main rail. Leave MCLR pulled up via a 10 kohm resistor for normal operation, or tie directly to VDD if not used. For ADC accuracy, keep analog traces short and away from switching nodes like the CWG outputs. This page synthesises distributor pricing, drop-in alternatives, and practical design notes beyond what the manufacturer datasheet alone provides, helping engineers compare options and make a sourcing decision quickly.

Запрос цены Контакты

PIC16F1615-I/SL

PIC16F1615-I/SL - 8-Bit 32MHz 14KB Flash MCU | Microchip

The Microchip Technology PIC16F1615-I/SL is an 8-bit RISC microcontroller featuring 14KB (8K x 14 words) of Flash program memory, 1KB of data RAM, and a maximum 32MHz CPU clock, housed in a 14-pin SOIC (SL) package with industrial -40C to +85C temperature rating. The part belongs to the PIC16(L)F161X family and integrates Core Independent Peripherals (CIPs) such as a 24-bit Signal Measurement Timer (SMT), Zero Cross Detection (ZCD), Configurable Logic Cell (CLC), and Complementary Waveform Generator (CWG), alongside Intelligent Analog modules including a 10-bit ADC with Computation and two comparators. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data bus and a RISC or CISC instruction set, integrating CPU, program memory (Flash/ROM), data memory (RAM), non-volatile EEPROM, timers, communication peripherals (UART, SPI, I2C), and digital/analog I/O. The 8-bit MCU belongs to the broader hierarchy of microcontroller -> embedded processor -> semiconductor, and is widely used in cost-sensitive, low-power, deterministic control applications. Microchip's PIC16 family is recognized for its deterministic architecture, low power consumption (XLP eXtreme Low Power), and ease of use with the MPLAB X IDE and XC8 compiler toolchain. Key features of the PIC16F1615 include 12 I/O pins, two PWM modules, 11 timers, an EUSART and MSSP for serial communication, 10-bit ADC, and Functional Safety (FuSa) support for IEC 61508 SIL-2 capable designs. The SL suffix indicates the 14-pin SOIC package, 1.75mm nominal height, 3.90mm body width, suitable for standard 0.1-inch pitch PCB layouts. The device operates from 2.3V to 5.5V across the industrial temperature range. Architecturally, the PIC16F1615 uses Microchip's enhanced mid-range core with hardware multiply support and a 14-bit instruction word. On-chip CIPs (CLC, CWG, SMT, ZCD) let designers implement complex signal conditioning, waveform generation, and timing measurements in hardware without CPU involvement, reducing firmware complexity and power consumption. The 24-bit SMT enables sub-microsecond timing resolution for energy metering or motor control feedback. Typical applications include small motor control (BLDC, stepper, brushed DC), LED lighting and constant-current regulation, IoT and battery-powered sensor nodes, home appliances, and functional-safety-embedded industrial controls. Functional Safety (FuSa) variants like this device support SIL-2-capable system designs with diagnostic libraries and FMEDA reports available from Microchip. When designing with this MCU, leave unused I/O as outputs driven low to minimize power, enable the watchdog timer for SIL applications, and use the CWG peripheral for hardware-driven complementary PWM rather than software bit-banging to reduce jitter. Program the device via In-Circuit Serial Programming (ICSP) using the ICSPCLK/ICSPDAT pins. This page synthesizes distributor pricing, drop-in alternative PIC16F161x family parts, and practical design notes not found on a single manufacturer page.

Запрос цены Контакты

PIC16F1615-I/ST

PIC16F1615-I/ST - 8-Bit 32MHz MCU 14KB Flash | Microchip

The Microchip PIC16F1615-I/ST is an 8-bit PIC® XLP™ 16F microcontroller running at up to 32 MHz, integrating 14 KB (8K x 14) of Flash program memory, 1 KB of SRAM, and a 10-bit A/D converter in a 14-pin TSSOP package. The part carries Microchip's Functional Safety (FuSa) capability and targets low-power embedded control of small motors and general-purpose applications. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (SRAM), peripherals, and I/O on one silicon die. MCUs sit at the bottom of the embedded compute hierarchy below microprocessors (MPUs) and system-on-chips (SoCs), and are preferred in cost- and power-constrained applications such as sensor nodes, small motor drivers, and human-machine interfaces. The PIC16F1615 belongs to the PIC16F1 enhanced mid-range family and is one of the smallest Flash members in Microchip's eXtreme Low Power (XLP) lineup. Key features include a 10-bit ADC with up to 8 channels, configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), Numerically Controlled Oscillator (NCO), Zero-Cross Detect (ZCD), 24-bit Signal Measurement Timer (SMT), and CCP/PWM peripherals. The device operates from 2.3 V to 5.5 V across -40 °C to +85 °C and offers sleep currents in the microamp range thanks to the XLP architecture. Core-independent peripherals offload tasks from the CPU, lowering average power and BOM cost. The device is built on an enhanced mid-range 8-bit RISC core with a modified Harvard architecture and 14-bit instruction word. The 32 MHz internal oscillator drives 8 MIPS throughput, with hardware multiplier and interrupt-driven I/O. Each instruction cycle is four oscillator clocks, balancing deterministic interrupt latency with active-mode current draw. Typical applications include small DC motor control, LED lighting drivers, fan control, battery-powered sensor hubs, home appliances, and safety-critical consumer devices that benefit from Functional Safety features. The TSSOP-14 footprint also suits hand-held and space-constrained designs. Designers should plan pin allocation before PCB layout because the 14-pin TSSOP exposes only a limited number of ADC channels and shared peripherals. Configuring the CLC and NCO in MPLAB X IDE allows logic replacement of discrete gates. This page synthesizes distributor pricing, drop-in alternatives within the same 14-TSSOP footprint, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC16F1615T-I/JQ

PIC16F1615T-I/JQ - 8-bit 32MHz MCU, 14KB Flash, 16-UQFN | Microchip

The Microchip Technology PIC16F1615T-I/JQ is an 8-bit PIC microcontroller from the PIC® XLP™ 16F family with Functional Safety (FuSa) features, integrating 14KB (8K × 14) of Flash program memory, 1KB of RAM, and a 32 MHz internal oscillator in a 16-pin UQFN (4 × 4 mm) package. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path that executes instructions on bytes; it sits within the broader taxonomy of microcontroller -> embedded controller -> semiconductor device, and the PIC16F1615 specifically belongs to Microchip's mid-range PIC16 family optimized for low-power, mixed-signal embedded control of small motors and general-purpose applications in 8/14/20-pin packages. Key features include a 10-bit ADC with multiple channels, Zero-Cross Detection (ZCD), Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Signal Measurement Timer (24-bit SMT), Windowed Watchdog Timer (WWDT), CRC/Memory Scan with hardware acceleration, and eXtreme Low Power (XLP) sleep modes drawing as little as 20 nA. Communication options include I²C, SPI, UART/USART, and LINbus. The PIC16F1615 uses an enhanced mid-range Harvard RISC architecture with a 14-bit instruction word, 49 instructions, and a hardware multiply, providing 8 MIPS at 32 MHz. The integrated 32 MHz high-precision internal oscillator eliminates the external crystal in many designs, while the Functional Safety (FuSa) features target IEC 60730 Class B safety requirements in household appliances and white goods. Typical applications include BLDC/PMSM small-motor commutation, LED lighting drivers with smooth dimming via the CWG module, IoT sensor nodes, household appliance control (washing machines, dishwashers), and battery-powered portable instruments requiring XLP sleep current budgets below 1 µA. When designing with this device, allocate the 16-UQFN footprint with a small thermal pad to the GND plane, follow Microchip's AN 1004 guidelines for UQFN PCB land patterns, and use MPLAB X IDE with the XC8 compiler for firmware development. Always confirm toolchain compatibility before migrating from older PIC16F1xxx devices. This page synthesizes distributor pricing, drop-in alternatives drawn from Microchip's PIC16 family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1615T-I/ML

PIC16F1615T-I/ML - 8-Bit MCU, 32MHz, 14KB Flash, 16-QFN | Microchip

The Microchip Technology PIC16F1615T-I/ML is an 8-bit PIC microcontroller from the PIC® XLP™ 16F family with Functional Safety (FuSa) capability, running at up to 32MHz core clock and integrating 14KB (8K x 14) of Flash program memory in a compact 16-pin QFN (4x4) package. It is supplied in tape-and-reel packaging and operates across the standard industrial temperature range of -40C to +85C, making it suitable for high-volume, surface-mount manufacturing. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash), data memory (RAM), and a rich set of peripherals onto one die. The PIC16F1615 belongs to the PIC16F1xxx enhanced mid-range family, which sits above baseline PIC10/12/16 architectures in performance and integration, yet below 16-bit PIC24 and dsPIC devices. Within the broader hierarchy, it is classified as a microcontroller -> embedded processor -> semiconductor device. XLP™ (eXtreme Low Power) denotes Microchip's portfolio of ultra-low-power 8-bit MCUs optimized for battery- and energy-harvesting applications. Key features of the PIC16F1615T-I/ML include an integrated 10-bit Analog-to-Digital Converter (ADC) with multiple channels, a 24-bit Signal Measurement Timer (SMT) for precision time and pulse-based measurements, Capture/Compare/PWM (CCP) peripherals, Zero-Cross Detect (ZCD) and Peripheral Pin Select (PPS) for flexible signal routing. The on-chip Functional Safety (FuSa) features support safety-critical designs targeting IEC 60730 Class B compliance for home appliances and similar regulated markets. The XLP architecture typically delivers deep-sleep currents in the nanoampere range, ideal for always-on applications. Typical applications for the PIC16F1615T-I/ML include small-motor control (BLDC fan, ceiling-fan, pump), consumer appliance control, IoT sensor nodes, LED lighting control with analog dimming, and general-purpose embedded control where 14KB Flash and 1KB RAM are sufficient. The 16-QFN (4x4) package is preferred when PCB area is at a premium and the design needs only 12-14 I/O pins. When designing with this part, budget the I/O count carefully - the 16-QFN package exposes fewer pins than 20- or 28-pin variants of the same family. Plan for an external decoupling network (100nF + bulk capacitor) within 2-3 mm of the VDD pin, and use MPLAB X IDE with the XC8 compiler for firmware development.

Запрос цены Контакты

PIC16F1615T-I/SL

PIC16F1615T-I/SL - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F1615T-I/SL is an 8-bit PIC16 microcontroller in the PIC® XLP™ 16F family, integrating 14 KB of Flash program memory, 1 KB of RAM, and a 32 MHz internal oscillator into a 14-pin SOIC package. The device is engineered for functional safety (FuSa) capable embedded control and ships in tape-and-reel packaging for high-volume surface-mount assembly lines. What is an 8-bit microcontroller? An MCU (microcontroller unit) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a configurable set of peripherals onto one silicon die. The 8-bit designation refers to the width of the internal data path and ALU; PIC16 cores use a RISC Harvard architecture with 14-bit instruction words. Within the broader semiconductor taxonomy, MCUs belong to the embedded processor family alongside 32-bit Cortex-M parts, and they sit under the application hierarchy of microcontrollers -> processors -> semiconductors. Key features of the PIC16F1615 include a 10-bit A/D converter with multiple channels, a Capture/Compare/PWM (CCP) module, a 24-bit Signal Measurement Timer (SMT), and Zero-Cross Detection (ZCD) hardware for TRIAC-based AC control. The XLP™ (eXtreme Low Power) designation indicates the device targets battery-powered applications through sub-microamp sleep currents and nanoWatt XLP technology. Operating voltages of 2.5V, 3.3V, and 5V are all supported, which simplifies integration across 2-cell battery, coin-cell, and regulated-rail designs. Typical applications include small motor control (especially brushed DC and low-voltage steppers), LED lighting drivers with TRIAC dimming, household appliance control boards, and general-purpose sensor hubs. The 14-pin footprint is the smallest in the PIC16F161X family, making this part attractive when board area is constrained but the richer 20-pin feature set is not required. When designing with this MCU, place a 0.1 µF decoupling capacitor within 2 mm of the VDD pin and route the ICSP™ programming signals (ICSPCLK/ICSPDAT) to a 5-pin header compatible with Microchip debuggers such as PICkit™ 4 or MPLAB® Snap. The 'T' suffix in the part number denotes tape-and-reel packaging, while the 'I' indicates the -40 °C to +85 °C industrial temperature grade.

Запрос цены Контакты

PIC16F1615T-I/ST

PIC16F1615T-I/ST - 8-bit MCU, 14KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F1615T-I/ST is an 8-bit PIC® XLP™ 16F microcontroller with 14KB Flash, 1KB RAM, 32MHz CPU, and Functional Safety (FuSa) features, housed in a 14-pin TSSOP package on tape-and-reel. It integrates a 10-bit ADC, CCP module, 24-bit SMT timer, Zero-Cross Detect, and multiple communications peripherals in a compact 14-pin footprint. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and integrated peripherals such as timers, ADCs, and communication interfaces. Within the broader taxonomy, MCUs sit inside embedded computing devices, which themselves branch from microprocessors and semiconductors. The PIC16F family is Microchip's mid-range 8-bit PIC architecture known for low-power XLP (eXtreme Low Power) operation, deterministic instruction execution, and a robust peripheral set. Key features include 14KB Flash program memory (8K x 14 words), 1KB RAM, 32MHz internal oscillator, 10-bit ADC with computation, hardware Capacitive Voltage Divider (CVD) support, Complementary Waveform Generator (CWG), 24-bit Signal Measurement Timer (SMT) for precision time-of-flight measurements, and Zero-Cross Detect (ZCD) for AC line sensing. The 'F' Flash variant supports 2.5V-5.5V operation while the 'LF' low-voltage variant supports 1.8V-3.6V. The PIC16F1615T-I/ST uses an enhanced mid-range 8-bit CPU core with a hardware multiplier, 49 instructions, and 16-level hardware stack. It supports in-circuit debugging via ICD and programming via ICSP, allowing field updates. The 14-pin TSSOP footprint integrates multiple peripherals through Peripheral Pin Select (PPS), enabling flexible pin assignment for designers working in space-constrained applications. Typical applications include small motor control (the on-chip CWG and 24-bit SMT are designed for this), AC line voltage and current sensing (ZCD + ADC), LED lighting ballast and dimming control, capacitive-touch user interfaces (CVD hardware), and general-purpose 8-bit embedded control in industrial and consumer products. The TSSOP-14 footprint suits compact PCB designs. When designing with the PIC16F1615T-I/ST, observe Microchip's recommended decoupling (100nF + bulk) and ensure unused pins are configured as outputs low or inputs with weak pull-ups. The PPS system requires peripheral-to-pin mapping be configured in firmware, while ZCD pin assignment and CCP capture source must be set explicitly. Leave adequate Flash and RAM headroom when migrating to next-generation PIC16F1xxx devices. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet - including a per-pin pinout and a same-package comparison against competing 14-pin TSSOP 8-bit MCUs from Microchip's own PIC16F1xxx family.

Запрос цены Контакты

PIC16F1618-E/ML

PIC16F1618-E/ML - 8-bit MCU, 7KB Flash, 32MHz | Microchip

The Microchip Technology PIC16F1618-E/ML is an 8-bit PIC® XLP™ microcontroller delivering 32 MHz CPU performance with 7 KB (4K x 14) of self-programmable Flash program memory and 512 bytes of SRAM, housed in a 20-pin 4x4 mm VQFN (ML) package with an exposed thermal pad. The device integrates a 10-bit Analog-to-Digital Converter with computation, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Zero-Cross Detection, and 24-bit Signal Measurement Timer (SMT) peripherals, and ships in an extended (E) -40C to +125C temperature grade. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory, volatile data RAM, and a peripheral set optimized for embedded control tasks. MCUs sit at the bottom of the computing hierarchy below microprocessors and are classified by bus width (8-bit, 16-bit, 32-bit), Flash program memory size, and integrated peripherals. PIC® microcontrollers use a Harvard RISC architecture with separate program and data buses, which is a design choice that simplifies instruction decoding and yields deterministic interrupt latency. Key features include seven 10-bit ADC channels, an internal 32 MHz oscillator, four Configurable Logic Cells for combinational and sequential logic, an 8-bit DAC, two PWM/SMT modules, and the proprietary XLP (eXtreme Low Power) technology that drops quiescent current to roughly 50 nA in sleep mode with peripherals running. The 24-bit SMT and CWG combine to support non-brushless DC motor control, fan speed regulation, and AC zero-cross sensing without an external ASIC. Typical applications include small brushed DC motor control, LED lighting drivers with zero-cross dimming, fan speed controllers, and general-purpose sensor signal conditioning. The combination of SMT, CWG, and CLC lets the PIC16F1618 replace two or three discrete timer ICs and a small logic array in cost-sensitive consumer appliances. The 20-pin VQFN footprint and Microchip's MPLAB X IDE / XC8 toolchain compatibility make prototyping straightforward, and the exposed pad aids thermal dissipation at full 32 MHz operation. When designing with this MCU, reserve the exposed pad as a continuous ground plane connection - the VQFN thermal pad is the primary heat path. Select the appropriate oscillator configuration (HFINTOSC, LFINTOSC, external) before writing code, because clock switching at runtime is gated by the Configuration Words. For new designs, validate that any drop-in alternative sits in the same 20-pin QFN footprint before committing PCB layout. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16F161X family, application guidance, and design notes that complement - but do not replace - the manufacturer datasheet. The VQFN package is also referred to as HVQCCN or 20-VFQFN-EP in manufacturer and distributor documentation.

Запрос цены Контакты

PIC16F1618-E/P

PIC16F1618-E/P - 8-Bit MCU, 7KB Flash, 32MHz, 20-PDIP | Microchip

The Microchip PIC16F1618-E/P is an 8-bit PIC microcontroller in the PIC16F161X family, featuring 7 KB of Flash program memory, 512 bytes of RAM, and a 32 MHz internal oscillator, housed in a 20-pin PDIP (DIP-20) through-hole package. The device operates from 2.5V to 5.5V, integrates a 10-bit ADC with up to 12 channels, and includes the eXtreme Low Power (XLP) feature set for battery-friendly designs. Built around an enhanced mid-range PIC16 core using a 14-bit instruction word, it executes most instructions in a single clock cycle, supporting deterministic real-time control. The -E temperature suffix indicates an extended industrial temperature range of -40C to +125C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals on one die. The PIC16 family belongs to the 8-bit microcontroller category, sitting within the broader hierarchy of embedded microcontrollers -> microcontrollers -> semiconductor ICs -> integrated circuits. 8-bit MCUs remain widely used for cost-sensitive, deterministic, low-power applications such as motor control, sensor interfacing, and consumer appliances where 32-bit performance is not required. Key differentiating features of the PIC16F1618 include 4 x 10-bit PWM outputs, a 24-bit Signal Measurement Timer (SMT) for precision time/capture, Zero-Cross Detect (ZCD) for TRIAC/SSR AC-line control, Complementary Waveform Generator (CWG), and Configurable Logic Cells (CLC) for hardware-level glue logic. These peripherals make it well suited to small motor and lighting-control applications without external timer or logic ICs. The internal architecture combines a Harvard-bus 14-bit instruction core with on-chip debug logic (ICD), enabling in-circuit programming and debugging via MPLAB X IDE and the PICkit/SNAP toolchain. The 10-bit ADC supports up to 12 analog inputs, and the device offers multiple communication interfaces including I2C, SPI, and EUSART. Typical applications include small BLDC and DC motor control, AC-line zero-cross switching for TRIAC dimmers, fan and pump speed controllers, white-goods and appliance control boards, IoT sensor edge nodes, battery-powered instrumentation, and general-purpose embedded control where extended-temperature operation is required. The 20-pin PDIP package simplifies prototyping on breadboards and through-hole PCBs. When designing with this device, ensure the 32 MHz operation is configured via the internal oscillator with proper PLL settings, and add a 0.1uF decoupling capacitor close to each VDD pin. MPLAB X IDE with the XC8 compiler is the standard development environment, and Microchip's Code Configurator (MCC) plugin can auto-generate peripheral initialization code. This page synthesizes distributor pricing snapshots, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone, giving engineers and buyers a single, actionable reference for the PIC16F1618-E/P.

Запрос цены Контакты

PIC16F1618-E/SO

PIC16F1618-E/SO - 8-bit MCU, 7KB Flash, 512B RAM, 20-SOIC | Microchip

The Microchip Technology PIC16F1618-E/SO is an 8-bit PIC microcontroller built on a RISC core, featuring 7KB of Flash program memory and 512 bytes of RAM in a 20-pin SOIC wide-body (7.50 mm) package. The device is part of the PIC16(L)F161x family, which is targeted at embedded control of small motors and general-purpose applications in 8/14/20-pin packages, with the 'E' suffix indicating the extended industrial temperature grade of -40C to +125C. According to the Microchip product page, the family integrates a 10-bit ADC, CCP module, 24-bit SMT (Signal Measurement Timer), Zero-Cross Detect (ZCD), and Windowed Watchdog Timer (WWDT) for robust embedded sensing and control. A PIC microcontroller (Programmable Interface Controller) is a compact, low-power 8-bit RISC microprocessor with on-chip Flash, RAM, EEPROM, and peripherals designed for embedded control. The PIC architecture belongs to the broader category of microcontrollers (MCUs), which in turn fall under microprocessors and semiconductors. PICs are widely adopted because of their deterministic instruction set, low power consumption, low cost, and rich peripheral integration that minimizes external components. Key features include 7KB Flash program memory, 512 bytes RAM, a 32 MHz internal oscillator, 10-bit ADC, 24-bit SMT, Zero-Cross Detect (ZCD), Windowed Watchdog Timer (WWDT), CRC/Scan, and configurable logic with up to 18 I/O pins. The 20-pin SOIC package provides ample I/O for typical embedded designs while remaining easy to hand-solder or rework, making the device attractive for low-to-mid-volume industrial and consumer products. The PIC16F1618 uses an enhanced mid-range 8-bit RISC core with a 14-bit instruction word, allowing most instructions to execute in a single instruction cycle. This architecture delivers deterministic interrupt latency and predictable code execution, which is essential for motor control loops, signal measurement, and timing-critical sensing tasks. The integrated 32 MHz internal oscillator reduces BOM cost and frees an external crystal pin. Typical applications include small motor control (BLDC, brushed DC, fan control), LED lighting and dimming, general-purpose embedded control, home appliances, sensor interfacing, and consumer electronics. The wide operating voltage and extended temperature range also suit industrial control and appliance motor drive boards. When designing with this device, ensure that the configuration bits are set correctly for the chosen oscillator and watchdog behavior. For motor-control applications, place the ZCD sensing traces away from switching nodes to avoid noise injection, and follow Microchip AN1914 and AN1606 for sensorless BLDC reference designs. This page synthesizes distributor pricing, drop-in alternatives from the same PIC16 family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F1618-E/SS

PIC16F1618-E/SS - 8-Bit 32MHz XLP MCU 7KB Flash 20-SSOP | Microchip

The Microchip Technology PIC16F1618-E/SS is an 8-bit PIC microcontroller from the PIC16(L)F161X family, featuring a 32 MHz internal oscillator, 7 KB (4K x 14) Flash program memory, 512 bytes SRAM, and 18 bytes data EEPROM, housed in a 20-pin SSOP package. It is engineered around Microchip's eXtreme Low Power (XLP) architecture, providing class-leading sleep currents for battery-driven embedded designs while integrating peripheral functions aimed at small-motor and general-purpose control. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral I/O. The PIC16F1618 is classified within the broader hierarchy: 8-bit microcontroller -> RISC microcontroller -> embedded controller -> semiconductor IC. It belongs to Microchip's mid-range PIC16 enhanced core family, which uses a Harvard RISC architecture that executes one instruction per clock cycle (other than branches), delivering deterministic throughput at modest clock rates. Key features include 18 I/O pins, a 10-bit ADC with automatic threshold scanning, a 24-bit Signal Measurement Timer (SMT) for precision time-based measurements, a Zero-Cross Detection (ZCD) module for TRIAC/SSR AC-line control, a Complementary Waveform Generator (CWG) for power-switching topologies, and up to four 10-bit PWM outputs with complementary pairing. The device supports 1.8V-5.5V operation (PIC16F1618 wide-voltage variant; the LF version is 1.8V-3.6V regulated). Technically, the PIC16F1618 builds on Microchip's enhanced mid-range core with a 14-bit instruction word and hardware multiplier, allowing compact code density. Integrated Core Independent Peripherals (CIPs) such as CWG, ZCD, and SMT operate without CPU intervention, freeing the core for system logic and reducing firmware complexity for closed-loop control tasks. Typical applications include BLDC/PMSM small-motor control (fans, pumps, appliance blowers), LED lighting drivers with dimming, AC-line TRIAC dimmers using ZCD, IoT sensor nodes requiring XLP sleep, household appliances, and general-purpose 8-bit embedded control boards in industrial and consumer products. When designing with this part, ensure the unused pins are configured as outputs or tied appropriately, and respect the 5.5V absolute maximum on VDD even when the LF variant is used at lower voltages. Always verify the exact voltage range suffix (F vs LF) before substitution. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not collected in any single manufacturer datasheet view.

Запрос цены Контакты

PIC16F1618-I/GZ

PIC16F1618-I/GZ - 8-bit MCU, 7KB Flash, 32MHz, 20-UQFN | Microchip

The Microchip Technology PIC16F1618-I/GZ is an 8-bit PIC microcontroller from the PIC16F161x family, delivering 7KB of Flash program memory, 512 bytes of RAM, and a 32 MHz internal oscillator in a 20-pin UQFN (4x4x0.5 mm) package. It targets embedded control of small motors and general-purpose applications where on-chip peripherals reduce external component count. The part is qualified for the industrial temperature range (-40C to +85C) and ships in tube packaging per the /GZ suffix. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and a Harvard or modified-Harvard architecture. Within the broader semiconductor taxonomy, MCUs sit inside the microcontroller category, which is itself a subclass of microprocessors, embedded processors, and ultimately integrated circuits. The PIC16F family uses a 14-bit instruction word optimized for compact code density and deterministic interrupt response, making these devices common in cost-sensitive real-time control loops. The PIC16F1618 sits under the PIC16F1614/1618 sub-family characterized by its 14/20-pin options and motor-control-oriented peripherals. Key on-chip features include a 10-bit Analog-to-Digital Converter (ADC) with multiple channels, a Zero-Cross Detector (ZCD) for AC line synchronization, a Windowed Watchdog Timer (WWDT) for safety-critical reset behavior, a cyclic redundancy check (CRC/SCAN) peripheral for memory integrity verification, a Configurable Logic Cell (CLC), Complementary Waveform Generator (CWG), and a Numerically Controlled Oscillator (NCO) for high-resolution frequency synthesis. Together these peripherals enable closed-loop BLDC and PFC designs without an external DSP. The device operates from 1.8V to 5.5V across the full -40C to +85C industrial range, simplifying battery- and USB-powered designs. Typical applications include small DC and stepper motor control, fan and pump controllers, LED lighting drivers with dimming, appliance user-interface boards, and general-purpose sensor-conditioning nodes. The combination of ZCD + CWG + NCO makes it particularly attractive for AC-line voltage dimmers and PFC stages, while the WWDT and CRC/SCAN target IEC 60730 safety-class B home-appliance designs. When designing with this part, ensure the trace between the ICSPDAT/ICSPCLK pins and the programming header is kept short to avoid programming errors, and route the analog AVSS/AVDD pair as a star ground to minimize ADC offset drift. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes that the manufacturer datasheet alone does not aggregate.

Запрос цены Контакты

PIC16F1618-I/ML

PIC16F1618-I/ML - 8-Bit MCU, 7KB Flash, 32MHz, 20-QFN | Microchip

The Microchip Technology PIC16F1618-I/ML is an 8-bit RISC microcontroller featuring a PIC16 core, 32 MHz maximum clock, 7 KB (4K x 14) of Flash program memory, and 512 bytes of SRAM, housed in a 20-pin QFN (4x4 mm) package with exposed pad. It belongs to the PIC® XLP™ 16F family, designed for low-power embedded control with eXtreme Low Power (XLP) technology. A microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), working memory (RAM), and programmable I/O peripherals. The 8-bit MCU class uses an internal data bus 8 bits wide and is favoured for deterministic real-time control, simple toolchains, and very low active and sleep currents. Within the 8-bit category, the PIC16 family is one of the most widely deployed architectures, spanning general-purpose, motor-control, and low-power XLP variants. The PIC16F1618 sits in the XLP branch, optimised for battery-powered and energy-harvesting applications. Key features include a 10-bit ADC with up to 12 channels, CCP/SCCP/PWM/24-bit SMT (Signal Measurement Timer) peripherals, Zero Cross Detect, a CLC (Configurable Logic Cell) block, multiple communication interfaces, and 18 I/O pins. The device operates from 2.3 V to 5.5 V, has an instruction cycle of 125 ns at 32 MHz, and supports both industrial (-40C to +85C) and extended (-40C to +125C) temperature ranges. Architecturally, the PIC16F1618 uses a Harvard RISC core with a 14-bit instruction word, an internal oscillator, and Microchip's nanoWatt XLP technology that delivers sleep currents down to the low nA range. The high-integration peripherals - including 24-bit SMT for precision time measurement, CLC for glue-logic replacement, and PWM with complementary outputs - reduce external component count and BOM cost. Typical applications include small motor control (BLDC, stepper, fan), LED lighting control, consumer electronics, battery-powered IoT sensor nodes, and general-purpose embedded control. The wide operating voltage range and low power make it well suited for both line-powered industrial and battery-powered portable products. When designing with the PIC16F1618, ensure the exposed thermal pad (EP) is soldered to a sufficiently large copper pour for both thermal dissipation and mechanical reliability. Decouple VDD with a 100 nF ceramic capacitor placed as close as possible to the pin pair, and follow Microchip's recommended ICSP programming layout if in-circuit programming is required. This page synthesises distributor pricing, drop-in alternatives from the same PIC16 family, and practical PCB/design notes not found in the manufacturer datasheet alone, helping procurement and design engineers quickly evaluate the PIC16F1618-I/ML for new designs and existing platform refreshes.

Запрос цены Контакты

PIC16F1618-I/P

PIC16F1618-I/P - 8-bit MCU, 7KB Flash, 20-Pin DIP | Microchip

The Microchip Technology PIC16F1618-I/P is an 8-bit flash microcontroller (MCU) from the PIC16F161X family, offering 7 KB of program Flash memory and 512 bytes of SRAM in a 20-pin PDIP through-hole package. It operates from 2.5V to 5.5V and integrates a 10-bit ADC with up to 17 channels, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Zero-Cross Detection (ZCD), and a 24-bit Signal Measurement Timer (SMT) for embedded motor control and general-purpose applications. An 8-bit microcontroller (MCU) is a programmable embedded processor built around an 8-bit data path and a RISC architecture, sitting in the broader hierarchy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC16F1618 belongs to the PIC16 family, one of Microchip's mid-range PIC architectures optimized for low power, deterministic interrupt response, and peripheral integration. With its 7 KB Flash and 512 bytes SRAM, this device is engineered for embedded control of small motors, lighting, and IoT edge nodes. Key features include 10-bit ADC, Configurable Logic Cells (CLC), Complementary Waveform Generator (CWG), Zero-Cross Detect (ZCD), Numerically Controlled Oscillator (NCO), 24-bit Signal Measurement Timer (SMT), Peripheral Pin Select (PPS), and eXtreme Low Power (XLP) sleep modes. These peripherals support motor commutation, frequency generation, and precise timing capture, enabling many functions without external ICs. The PIC16F1618 uses a Harvard architecture with separate program and data buses, supporting up to 32 MHz internal oscillator operation. Its Core Independent Peripherals (CIPs) can operate without CPU intervention, freeing the core for application logic. The device includes enhanced mid-range 14-bit instruction set compatibility. Typical applications include small motor control (BLDC, stepper), LED lighting drivers, fan control, home appliances, IoT sensor nodes, and industrial automation. The combination of CWG, ZCD, and SMT makes it ideal for AC line zero-cross detection-based motor control and TRIAC phase-angle dimming. When designing with this MCU, ensure the VDD decoupling capacitor is placed within 5 mm of the VDD pin and that ICSP programming pins (ICSPCLK/ICSPDAT) are accessible for in-circuit programming. The device supports 2.5V-5.5V operation, allowing direct interfacing with 5V peripherals without level shifters. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

PIC16F1614-I/ML - 8-bit MCU, 7KB Flash, 32MHz, 16-QFN | Microchip

PIC16F1614-I/P - 8-Bit MCU, 7KB Flash, 32MHz, 14-PDIP | Microchip

PIC16F1614-I/SL - 8-Bit 32MHz MCU 7KB Flash | Microchip

PIC16F1614-I/ST - 8-Bit MCU, 7KB Flash, 32MHz, TSSOP-14 | Microchip

PIC16F1614T-I/SL - 8-bit MCU, 7KB Flash, 32MHz | Microchip

PIC16F1615-E/ML - 8-bit MCU, 14KB Flash, 32MHz, QFN-16 | Microchip

PIC16F1615-E/P - 8-Bit 32MHz 14KB Flash MCU | Microchip 14-PDIP

PIC16F1615-E/SL - 8-bit MCU 14KB Flash 32MHz 14-SOIC | Microchip

PIC16F1615-I/JQ - 8-bit 32MHz MCU, 14KB Flash, 16-UQFN | Microchip

PIC16F1615-I/ML - 8-Bit 32MHz 14KB Flash MCU | Microchip

PIC16F1615-I/P - 8-Bit 32MHz MCU 14KB Flash 14-PDIP | Microchip

PIC16F1615-I/SL - 8-Bit 32MHz 14KB Flash MCU | Microchip

PIC16F1615-I/ST - 8-Bit 32MHz MCU 14KB Flash | Microchip

PIC16F1615T-I/JQ - 8-bit 32MHz MCU, 14KB Flash, 16-UQFN | Microchip

PIC16F1615T-I/ML - 8-Bit MCU, 32MHz, 14KB Flash, 16-QFN | Microchip

PIC16F1615T-I/SL - 8-Bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F1615T-I/ST - 8-bit MCU, 14KB Flash, 32MHz | Microchip

PIC16F1618-E/ML - 8-bit MCU, 7KB Flash, 32MHz | Microchip

PIC16F1618-E/P - 8-Bit MCU, 7KB Flash, 32MHz, 20-PDIP | Microchip

PIC16F1618-E/SO - 8-bit MCU, 7KB Flash, 512B RAM, 20-SOIC | Microchip

PIC16F1618-E/SS - 8-Bit 32MHz XLP MCU 7KB Flash 20-SSOP | Microchip

PIC16F1618-I/GZ - 8-bit MCU, 7KB Flash, 32MHz, 20-UQFN | Microchip

PIC16F1618-I/ML - 8-Bit MCU, 7KB Flash, 32MHz, 20-QFN | Microchip

PIC16F1618-I/P - 8-bit MCU, 7KB Flash, 20-Pin DIP | Microchip