Интегральные схемы

PIC16F570-E/SS

PIC16F570-E/SS - 8-Bit MCU, 3KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC16F570-E/SS is an 8-bit enhanced baseline Flash microcontroller in a 28-pin SSOP package, integrating 3KB Flash program memory, 64 bytes RAM, and on-chip analog peripherals that are unusual for an entry-level MCU. According to the manufacturer datasheet, the PIC16F570 combines a RISC CPU core with 11 ADC channels, two operational amplifiers, two analog comparators, and a 64-byte EEPROM-style data area on the same die, eliminating the need for external analog components in cost-sensitive mixed-signal designs. An 8-bit microcontroller (MCU) is a microprocessor optimized for embedded control, integrating CPU, RAM, program memory, and peripherals (ADC, timers, communication ports) on a single chip. The PIC16F570 belongs to Microchip's enhanced baseline family - positioned below mid-range PIC16 devices - and is part of the broader 8-bit PIC microcontroller hierarchy: enhanced baseline -> mid-range -> enhanced mid-range PIC. This taxonomy matters for engineers selecting migration paths because higher-tier devices add instructions and peripherals while keeping pin compatibility within the same package. Key features that distinguish the PIC16F570 include an integrated dual op-amp stage (configurable for inverting, non-inverting, or comparator modes), two dedicated comparators with programmable reference, an 11-channel 8-bit ADC, and 64 bytes of internal data EEPROM emulation. The device operates from 2.0V to 5.5V, runs up to 20MHz (200 ns instruction cycle), and offers low-power operation with several sleep/idle modes for battery-driven applications. The Enhanced Baseline core delivers 33 single-word instructions with 12-bit-wide opcodes. Architecture-wise, the PIC16F570 uses a Harvard RISC design with separate program and data buses, allowing instruction fetch and operand access to occur in the same cycle. The integrated analog peripherals are powered by a dedicated internal bandgap reference and can operate independently of the CPU, making the device suitable for always-on sensor monitoring. The dual op-amps can be configured as programmable gain stages feeding the ADC, reducing the bill of materials in closed-loop control loops. Typical applications include sealed-lead battery chargers, uninterruptible power supplies, lighting ballast control, security sensor front ends, motor control pre-drivers, and consumer appliances where integrated analog reduces PCB area. The wide operating temperature range (-40C to +125C, indicated by the -E suffix) supports industrial and automotive underhood environments. When designing with this device, ensure the 28-SSOP exposed-thermal land is soldered to a copper pour for improved heat dissipation and mechanical reliability. The device is in-system programmable via ICSP and supports self-write to its own Flash for bootloader applications. This page synthesizes distributor pricing, drop-in alternatives, and design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC16F570-I/MV

PIC16F570-I/MV - 8-Bit 20MHz MCU 3KB Flash 28-UQFN | Microchip

The Microchip PIC16F570-I/MV is an 8-bit PIC16-family RISC microcontroller with integrated analog peripherals, packaged in a 28-pin UQFN (4x4 mm) form factor. It combines a 20 MHz CPU core with 3 KB (2K x 12 words) of Flash program memory, 132 bytes of data RAM, and a unique on-chip analog subsystem that includes a multi-channel ADC, two operational amplifiers, and two comparators. The industrial temperature grade (-40C to +85C) and 28-UQFN package make it a compact analog-front-end MCU for cost-sensitive embedded designs. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data memory, and peripheral interfaces into one IC. The PIC16F570 belongs to the PIC16 mid-range family - 8-bit RISC microcontrollers known for deterministic instruction execution (200 ns per instruction at 20 MHz), Harvard architecture with separate program and data buses, and a broad ecosystem of MPLAB X development tools. PIC16 MCUs sit below PIC18/PIC24 in Microchip's 8-bit portfolio, offering lower cost and smaller footprints than PIC24/dsPIC parts while providing more on-chip analog than baseline PIC10/12/16F5xx devices. Key features include 3 KB Flash with self-programmability, 64 bytes of EEPROM data memory, two 8-bit timers plus one 16-bit timer, a 10-bit ADC with multiple channels, two on-chip op-amps configurable as unity-gain buffers or amplifiers, two analog comparators with reference, an internal 8 MHz oscillator, and an integrated voltage reference. The 28-UQFN package provides a small 4x4 mm footprint suitable for space-constrained PCB designs while exposing 23 I/O pins. The device supports In-Circuit Serial Programming (ICSP) and In-Circuit Debugging (ICD) via standard 2-wire interfaces. Architecturally, the PIC16F570 uses a Harvard RISC core with a 14-bit instruction word, 8-bit data path, and a 2-stage pipeline, delivering 200 ns instruction time at 20 MHz. The on-chip op-amps and comparators are routed through dedicated analog I/O pins and can be configured during runtime to condition sensor signals before ADC sampling - effectively replacing discrete analog front-end ICs in many designs and lowering BOM count. The 10-bit ADC with selectable reference and acquisition time delivers approximately 1 LSB accuracy at moderate conversion rates. Typical applications include battery chargers and power management controllers, LED lighting controllers, sensor signal conditioning modules, smoke detectors, white-goods user-interface boards, and small motor control loops. The integrated op-amp + comparator + ADC chain is particularly useful for closed-loop current/voltage sensing without external analog ICs. Designers select the PIC16F570 when they need more analog integration than PIC16F505/506 but smaller code and lower cost than PIC16F193x parts. When designing with this part, ensure that the ICSP/ICD pins (RB6/RB7) are not loaded with low-impedance circuits during programming. Use MPLAB X IDE with XC8 compiler for firmware development, and select a VDD decoupling network of 100 nF plus 10 uF bulk capacitance near the UQFN exposed pad. The exposed thermal pad must be soldered to the ground plane for mechanical reliability and electrical performance. The PIC16F570 is also available in PIC16F570-E/MV (extended temperature grade) and PIC16F570T-I/MV (tape-and-reel packaging) variants for different volume/production needs. This page synthesizes distributor pricing, drop-in alternative cross-references, and design notes not consolidated in the Microchip datasheet.

Запрос цены Контакты

PIC16F570-I/SP

PIC16F570-I/SP - 8-bit MCU, 3KB Flash, 20MHz, Dual Op Amps | Microchip

The Microchip PIC16F570-I/SP is an 8-bit PIC16 family flash microcontroller integrated with on-chip analog peripherals, packaged in a 28-pin SPDIP (Skinny Plastic Dual In-line Package). It features a 20 MHz maximum CPU clock (200 ns instruction cycle), 3 KB (2K x 12) of Flash program memory, 64 bytes of data RAM, and an integrated ADC plus two operational amplifiers plus two comparators, delivering a mixed-signal MCU in a single die. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and peripherals. The PIC16F570 belongs to the PIC16F family of 8-bit RISC microcontrollers from Microchip, positioned below the PIC18 and PIC24 families in the PIC architecture hierarchy: 8-bit PIC16 -> 8-bit PIC microcontrollers -> embedded microcontrollers -> microprocessors -> semiconductors. The integrated op amps and comparators differentiate this MCU from typical PIC16 baseline devices, eliminating the need for external analog components in many sensor-interface and signal-conditioning designs. Key features include 24 I/O pins, a 5-channel 8-bit ADC with internal voltage reference, two rail-to-rail operational amplifiers configurable by software, two analog comparators, an internal 8 MHz oscillator (with external clock options up to 20 MHz), in-circuit serial programming (ICSP), and a wide 2.5V to 5.5V operating voltage range. The device supports industrial -40C to +85C operation and offers low-power sleep modes suitable for battery-powered applications. The PIC16F570 utilizes Microchip's enhanced mid-range 14-bit instruction set architecture (a superset of the baseline 12-bit PIC instruction set), enabling C-compiler-friendly code development while maintaining upward compatibility with other PIC16F devices. The on-chip Flash allows in-application reprogramming, and the ICSP interface permits board-level programming without removing the device. Typical applications include smoke detectors, sensor signal conditioning, battery chargers, LED drivers with analog feedback, and small industrial control loops where the integrated op amps remove the need for external analog front-end ICs. When designing with the PIC16F570, ensure the op-amp output swing and ADC input range match the intended signal levels, and use Microchip's MPLAB X IDE with the XC8 compiler for development. The 28-pin SPDIP package is through-hole and easy to prototype on perfboard or through-hole PCBs. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes for engineers comparing PIC16F570 variants, not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F570T-I/MV

PIC16F570T-I/MV - 8-bit MCU 3KB Flash 28-Pin UQFN | Microchip

The Microchip Technology PIC16F570T-I/MV is an 8-bit flash microcontroller that combines an integrated analog engine with the intelligence of a PIC16 core, offered in a compact 28-pin UQFN (MV) surface-mount package with tape-and-reel packaging. It integrates 3 KB of flash program memory, 64 bytes of RAM, and a peripheral mix that includes an 8-channel 8-bit ADC, two operational amplifiers, two comparators, and a configurable reference, all rated for operation from 2.0 V to 5.5 V across an industrial -40 C to +85 C temperature range. An 8-bit microcontroller (MCU) is a compact programmable processor that combines a CPU, on-chip memory, and a fixed set of peripherals (ADC, timers, communications, analog) into a single device. Within the broader semiconductor taxonomy, MCUs sit under microcontrollers, then embedded processors, then logic/semiconductor devices. Microchip's PIC16 family targets cost-sensitive applications that need reliable 8-bit performance with deterministic interrupt response, and the PIC16F570 distinguishes itself by integrating true analog building blocks (op-amps and comparators) directly on-die. Key features include 3 KB self-programmable flash (up to 100,000 erase/write cycles), 128 bytes of EEPROM, and a 25 I/O pin budget with high-current sink/source capability. The dual on-chip op-amps can be configured as buffers, amplifiers, or filters, while the two comparators share an internal 0.6 V/1.2 V/2.5 V reference. Eight MHz internal oscillator eliminates external crystals in cost-sensitive designs, and in-circuit serial programming (ICSP) allows in-field firmware updates. Typical applications include industrial sensor conditioning loops, battery chargers, motor control front-ends, smart thermostats, low-end consumer appliances, and LED lighting controllers. The combination of integrated op-amps and comparators makes the PIC16F570T-I/MV particularly well-suited to closed-loop analog systems where PCB area and BOM cost matter more than raw CPU throughput. When designing with this device, keep analog and digital grounds separated and meet at a single point near the IC to avoid noise coupling into the op-amp/comparator stages. Use the internal 8 MHz oscillator only when timing tolerance is non-critical, since factory trim accuracy is approximately +/- 1 percent at room temperature.

Запрос цены Контакты

PIC16F570T-I/SS

PIC16F570T-I/SS - 8-Bit MCU, 3KB Flash, 28-SSOP | Microchip

The Microchip Technology PIC16F570T-I/SS is an 8-bit PIC16 RISC flash microcontroller with integrated analog peripherals, running at up to 20 MHz instruction clock and housed in a 28-pin SSOP package. Key headline parameters are 3 KB (2K x 12) of FLASH program memory, 132 bytes of data RAM, and an integrated 8 MHz internal oscillator, all in a 5.30 mm SSOP-28 (SS) outline supplied on Tape & Reel (the "T" suffix). A PIC (Peripheral Interface Controller) microcontroller is a compact RISC-based computing core with on-chip program memory, data RAM, and integrated peripherals such as timers, ADC, comparators, and communication blocks. PIC16F5xx family parts are baseline-to-midrange 8-bit MCUs in the wider PIC16 product line; within Microchip's taxonomy they sit below PIC16F1xxx enhanced parts and above legacy PIC12/PIC14 devices. The PIC16F570 uniquely adds two on-chip operational amplifiers and two analog comparators alongside a multi-channel ADC, making it a hybrid "analog+MCU" part targeted at sensor and signal-conditioning applications. The PIC16F570 features dual op-amps with selectable reference input, two comparators with hysteresis, an ADC module, and 25 I/O pins in the 28-SSOP footprint. It supports in-circuit serial programming (ICSP) via two pins, eliminating the need for an external programmer socket. The device operates across 2.0 V to 5.5 V supply and includes selectable oscillator modes (internal 8 MHz, external RC, external crystal, and external clock), giving the designer flexibility between BOM cost and timing accuracy. Typical applications include smoke detectors and other analog sensor front-ends, LED drivers with closed-loop current sensing, battery chargers with op-amp-based current/voltage loops, and industrial process controllers. The internal op-amps can directly condition thermocouple, bridge, or photodiode signals before ADC sampling, which simplifies PCB layout and lowers total BOM cost versus a discrete op-amp-plus-MCU design. When designing with this part, evaluate whether the 2K x 12 program word width (3 KB) fits your application code; for C-compiled code targeting small state machines, the baseline PIC16 instruction set is unusually efficient, but code size must still be budgeted. Note the SSOP-28 package is pin-limited for designs needing many I/Os. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. Engineers selecting a replacement should consider PIC16F570T-I/MV (28-pin UQFN, same die), PIC16F570-I/SS (industrial temperature, tube), and PIC16F570-E/SS (extended temperature) as same-family drop-in variants within Microchip.

Запрос цены Контакты

PIC16F57T-E/SO

PIC16F57T-E/SO - 8-Bit 20MHz PIC16 MCU, 3KB Flash | Microchip

The Microchip Technology PIC16F57T-E/SO is a flash-based, 8-bit CMOS microcontroller from the PIC16F5X family, executing instructions in 200 ns and packaged in a 28-pin SOIC wide-body (SO) tape-and-reel format. It integrates 3KB (2K x 12) of flash program memory, 72 bytes of RAM, 20 MHz maximum oscillator input, and 20 I/O pins on a 0.5 mA typical operating supply. The -E suffix denotes the extended industrial temperature grade of -40C to +125C, with the device operating from 2.5 V, 3.3 V, or 5 V supplies. What is a PIC16F5X microcontroller? The PIC16F5X is a baseline 8-bit RISC microcontroller family from Microchip, designed as a simple, low-cost entry point into the PIC architecture. PIC microcontrollers sit within the broader category of microcontrollers, which are single-chip computers integrating CPU, RAM, non-volatile program memory, and I/O peripherals. Within the MCU taxonomy, the PIC16F5X belongs to the 8-bit MCU tier using a RISC (Reduced Instruction Set Computing) architecture, distinct from 16-bit PIC24, 32-bit PIC32, and Cortex-M families. The PIC16F5X uses a 12-bit instruction word and exposes 33 single-word instructions, delivering 2:1 code compression over competitive 8-bit MCUs in its class. The device features 33 single-word instructions, a two-level hardware stack, 8-bit timer/counter with prescaler, watchdog timer with its own on-chip RC oscillator, power-on reset, and power-saving SLEEP mode. It uses a Harvard architecture with separate program and data buses, achieving deterministic execution and most instructions completing in one instruction cycle. The 20 MHz input clock yields a 200 ns instruction cycle, and the on-chip RC oscillator eliminates an external resonator in many designs. Typical applications include automotive subsystems, industrial control logic, appliance control boards, sensor signal conditioning, low-end consumer electronics, LED driving, simple motor control, and battery-powered embedded devices where the -40C to +125C temperature range and tape-and-reel packaging make it suitable for high-volume surface-mount assembly. The SOIC-28 wide-body package is compatible with hand-soldering and automated SMT lines. When designing with this part, choose the -E (extended) grade for automotive or industrial temperature exposure and the standard -I grade for commercial/consumer designs. The flash memory is one-time programmable by Microchip; in-circuit serial programming (ICSP) is supported via dedicated RB6/RB7 pins, enabling firmware updates in production.

Запрос цены Контакты

PIC16F57T-E/SS

PIC16F57T-E/SS - 8-bit 20MHz 3KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC16F57T-E/SS is an 8-bit PIC RISC microcontroller with 3KB (2K x 12) of Flash program memory, 72 bytes of RAM, and 20 digital I/O pins, housed in a 28-pin SSOP package with -40C to +125C extended-temperature grade. It executes instructions in 200 ns at a 20 MHz clock, supports a 4.5V to 5.5V supply, and ships in Tape & Reel packaging. What is an 8-bit Flash microcontroller? An 8-bit Flash microcontroller is a small, self-contained computer-on-a-chip that integrates a CPU, non-volatile Flash program memory, RAM, and peripherals on a single die. It belongs to the broader class of microcontrollers (MCU) under the larger semiconductor hierarchy: microcontroller -> embedded processor -> integrated circuit. The PIC16F57 sits within Microchip's baseline PIC16F family and is one of the original mid-range 14-bit instruction PIC16F5x devices, optimized for cost-sensitive applications requiring deterministic, low-pin-count control. Key features include 33 single-word instructions, a 12-bit wide instruction set that yields 2:1 code compression versus typical 8-bit CISC competitors, two 8-bit timer/counters, a watchdog timer with on-chip RC oscillator, and in-circuit serial programming (ICSP) via dedicated RB6/RB7 pins. The 20 MHz oscillator delivers 5 MIPS throughput. Architecturally, the PIC16F57T-E/SS uses a Harvard RISC core with separate program and data buses, allowing instruction fetch and operand access in a single cycle. The wide 12-bit opcode and 8-bit data path are tuned for compact assembly code on small ROM footprints, making it well suited to standalone control loops where a smaller, cheaper MCU replaces a discrete logic implementation. Typical applications include automotive body and chassis modules, industrial control logic, appliance controls, security and alarm panels, and general-purpose low-pin-count glue logic. The wide 4.5V to 5.5V supply tolerance and automotive AEC-Q100-style extended temperature range make it adaptable to harsh environments. When designing with this device, note that the PIC16F57 family is programmed via ICSP and does not expose all RAM and ROM addresses externally; code developed for the PIC16F57 cannot always be ported to enhanced mid-range PIC16F1xxx parts without recompilation. Provide adequate decoupling on VDD and a stable oscillator for reliable operation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F57T-I/SO

PIC16F57T-I/SO - 8-Bit 20MHz 3KB Flash MCU | Microchip | 28-SOIC

The Microchip Technology PIC16F57T-I/SO is a powerful yet easy-to-program 8-bit CMOS FLASH-based microcontroller from the PICmicro architecture, packaged in a 28-pin SOIC (7.50 mm width) with 200 ns instruction execution, 20 MHz clock speed, 3 KB (2K x 12) program FLASH memory, and 20 I/O pins. Operating from a 2.0V to 5.5V supply, the device is engineered for low-power embedded control in automotive, industrial, and consumer applications. A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/ROM for program storage, RAM for data), and programmable I/O peripherals on one IC. The PIC16F57 belongs to Microchip's mid-range 8-bit PIC16 family and uses a RISC-based Harvard architecture with 33 single-word instructions and 12-bit-wide opcodes delivering roughly 2:1 code compression versus other 8-bit MCUs in its class. Within the broader component taxonomy, PIC16F57 sits under microcontroller -> 8-bit MCU -> embedded controller -> semiconductor IC -> Integrated Circuit. Its 12-bit instruction width is a hallmark of the PIC16F5X baseline family, distinguishing it from PIC16F1xxx enhanced 14-bit devices and PIC18 16-bit-instruction parts. Key features include 72 bytes of RAM, three hardware timers, a watchdog timer, 20 digital I/O lines, in-circuit serial programming (ICSP), and an integrated power-on reset. The PIC16F57T-I/SO is supplied in tape-and-reel (T = T&R suffix) for high-volume manufacturing, the -I grade parts operate across -40 C to +85 C industrial temperatures, and the SO package (SO = 28-SOIC) offers 0.295 inch (7.50 mm) body width for standard through-hole-compatible surface-mount assembly. In-circuit debug and code protection are supported per Microchip device specifications. Compared with PIC16F1xxx enhanced mid-range parts, the PIC16F57 lacks interrupts, ADC, and PWM peripherals, which makes it ideal for deterministic polled-loop control. The 20 MHz oscillator drives a 5 MIPS core from a 4T clock, balancing responsiveness with ultra-low sleep currents for always-on remote-sensor nodes. Typical applications include automotive sensor conditioning, industrial control logic, appliance user-interface panels, low-cost remote controls, security-system keypads, and LED display drivers. The wide supply range (2.0-5.5V) allows direct connection to single-cell Li-ion or 4xAA battery stacks. Designers should connect VDD to a 100 nF decoupling capacitor placed within 5 mm of the pin and route MCLR through a 10 kohm pull-up. For production programming, reserve the ICSP pins (RB6/RB7) and ensure the trace geometry avoids capacitive loading on the oscillator pins. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for evaluating the PIC16F57T-I/SO in new designs and as a pin-compatible upgrade or replacement.

Запрос цены Контакты

PIC16F57T-I/SS

PIC16F57T-I/SS - 8-Bit 20MHz 3KB Flash MCU 28-SSOP | Microchip

The Microchip Technology PIC16F57T-I/SS is an 8-bit RISC flash microcontroller featuring a 20 MHz maximum operating frequency, 3KB (2K x 12) of program FLASH memory, and 72 bytes of RAM, housed in a 28-pin SSOP (Shrink Small Outline Package). It executes instructions in a 200 ns single-cycle period, supports 33 single-word instructions, and operates from a 2.0V to 5.5V supply with seven I/O pins and a 12-bit-wide instruction word. The /SS suffix denotes the SSOP-28 industrial-temperature (-40C to +85C) tape-and-reel variant. A PIC16 series 8-bit microcontroller is a RISC-based (Reduced Instruction Set Computer) embedded controller from the PICmicro architecture family. It belongs to the hierarchy MCU (microcontroller unit) -> 8-bit MCU -> PIC16 family -> FLASH-based PIC16F5x sub-family, a class of cost-optimized microcontrollers designed for simple, deterministic control loops. These devices use a Harvard memory architecture with separate program and data buses and a 12-bit or 14-bit wide instruction word, giving them deterministic timing that simplifies firmware development in low-power, interrupt-driven applications. Key features of the PIC16F57T-I/SS include 72 bytes of data RAM, an 8-bit timer/counter, a watchdog timer with on-chip RC oscillator, power-on reset, brown-out reset, and In-Circuit Serial Programming (ICSP) for in-system firmware updates. The device supports external crystal, ceramic resonator, or RC oscillator clocking modes. With only 33 single-word instructions and a 2-level hardware stack, it is one of the simplest PIC microcontrollers to learn and deploy. Architecturally, the PIC16F57T-I/SS uses a Harvard RISC core with a 12-bit program word and an 8-bit data path. The FLASH program memory is endurable to 100,000 write/erase cycles and supports in-circuit programming via two pins, eliminating the need for a separate programmer socket. The wide 2.0V-5.5V operating range allows direct battery or USB-bus-powered operation. Typical applications include consumer white goods control, low-end sensor signal conditioning, battery-powered remote controls, LED lighting controllers, hobbyist and education platforms, simple appliance timers, automotive interior accessories, and industrial replacement of legacy 8-bit logic glue. Its automotive temperature-grade option and small SSOP footprint suit space-constrained applications. When designing with the PIC16F57T-I/SS, ensure that the ICSP clock and data lines have series resistors to isolate them from the application circuit during programming. Place a 0.1uF decoupling capacitor as close as possible to VDD, and use a bulk capacitor if the supply has high source impedance. The PIC16F5x family lacks an internal oscillator on some variants - confirm clock source requirements against your application before layout. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC16F59-E/P

PIC16F59-E/P - 8-bit 20MHz 3KB Flash MCU 40-DIP | Microchip

The Microchip Technology PIC16F59-E/P is an 8-bit CMOS flash-based microcontroller in the PIC16F5X baseline family, packaged in a 40-pin DIP (PDIP-40) and rated for the extended -40C to +125C operating range. It integrates 3KB of Flash program memory, 72 bytes of RAM, 20 digital I/O lines, an 8-bit timer (TMR0), a watchdog timer, and In-Circuit Serial Programming (ICSP). The core executes 33 single-cycle RISC instructions at up to 20 MHz clock speed. A baseline PIC16 microcontroller is an 8-bit RISC processor built around a small instruction set (typically 33 instructions) with a 2-level hardware stack. In the broader taxonomy it sits below mid-range PIC16F1xxx devices in capability but above 6-pin PIC10F parts. Baseline PIC16 devices are commonly used for low-cost, deterministic control tasks where tiny code size and a shallow learning curve matter more than peripheral richness. Flash-based program memory enables field-reprogrammability via ICSP without removing the part from the board. Key features include a 200 ns instruction execution time, 12-bit-wide instructions, 8-bit-wide data path, low-power 100 nA typical sleep current, and a wide 4.5V to 5.5V supply range. The device has no on-chip data EEPROM, so non-volatile data storage must be implemented with Flash self-write techniques or external storage. Brown-out protection, power-on reset, and watchdog logic are integrated for robust embedded operation. Typical applications include white-goods and appliance control, simple sensor conditioning, LED drivers, low-cost consumer toys, fan controllers, and remote-control transmitters. Industrial and automotive accessory designs use the extended -40C to +125C variant (E suffix) for cabin and under-hood-tolerant sub-systems. The 40-pin DIP package is also favored for educational, hobby, and breadboard-friendly prototyping due to its large pin pitch and through-hole mounting. Design consideration: the 2-level hardware stack imposes a strict limit on nested subroutine and interrupt depth - use this device only for flat or shallow call graphs. Designers migrating to PIC16F1xxx mid-range devices gain a deeper stack, more peripherals, and data EEPROM at the cost of higher unit price and slightly more complex peripherals. This page synthesizes distributor pricing, parametric same-package drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F59-E/PT

PIC16F59-E/PT - 20MHz 8-Bit MCU, 3KB Flash | Microchip

The Microchip Technology PIC16F59-E/PT is a flash-based 8-bit CMOS microcontroller with a 20 MHz peak clock rate, 3 KB of program Flash memory, 128 bytes of RAM, and 32 I/O pins in a 44-lead TQFP package. It belongs to the PIC16F5X family and uses the PIC instruction set for compact embedded-control designs. An 8-bit microcontroller is a programmable semiconductor containing a CPU core, program memory, data memory, and peripherals on one integrated circuit. PIC16F59 belongs to the PIC16 family, which is part of the broader embedded-controller and semiconductor hierarchy. Its compact instruction set and modest memory footprint suit applications that need deterministic control, status monitoring, or simple user-interface logic without a high-cost processor. Key features include 3 KB of Flash program memory, an 8-bit data path, 32 I/O pins, and operation from 2.5 V, 3.3 V, or 5 V according to the verified distributor data. The device also provides a TMR0 timer, a watchdog timer, low-power sleep operation, and in-circuit serial programming. These resources allow a design to combine timing, supervisory behavior, and external control in one integrated device. The PIC16F59 uses 12-bit program instructions, and most instructions execute within one cycle, while program branches require two cycles according to the family information in the verified search results. Its 33-instruction baseline core and two-level stack keep the programming model straightforward. The 44-lead TQFP provides substantially more I/O capacity than smaller PIC16 packages while remaining compatible with automated board assembly. Typical applications include industrial control modules, appliance controllers, small sensor-hub boards, LED status panels, and compact embedded systems. The 32 available I/O pins are particularly useful when the design needs digital inputs and outputs beyond the resources of a smaller PIC microcontroller. The PIC16F59-I/PT and PIC16F59T-I/PT variants provide related temperature-grade and packaging options where verified sourcing permits. Designers should account for programming and clock configuration, provide suitable decoupling near the supply pins, and verify every peripheral signal against the manufacturer pinout before layout release. In-circuit serial programming can simplify production programming, but programming access, oscillator stability, and unused-pin treatment must be checked in the device-specific documentation. This page combines verified manufacturer and distributor data with package-focused alternatives, explicit data gaps, and practical selection guidance. It adds engineering context for comparing the 44-lead TQFP PIC16F59 variants without treating different-package devices as drop-in replacements.

Запрос цены Контакты

PIC16F59-I/P

PIC16F59-I/P - 8-Bit 20MHz 3KB Flash MCU 32 I/O | Microchip

The Microchip Technology PIC16F59-I/P is an 8-bit RISC flash-based microcontroller (MCU) in the PIC16F5x baseline family, featuring 3KB (2K x 12 words) of FLASH program memory, 134 bytes of RAM, and 32 digital I/O lines, all housed in a 40-pin PDIP (DIP-40) through-hole package. It executes instructions at 200 ns per cycle from a maximum 20 MHz oscillator, integrates power-on reset (POR) and a Watchdog Timer (WDT) for robust embedded operation, and operates from 2.0 V to 5.5 V across the industrial -40C to +85C temperature range. A PIC microcontroller is a compact, low-power programmable processor built on a Harvard RISC architecture that separates program and data memory for deterministic single-cycle instruction execution. The PIC16F5x baseline family uses a 12-bit-wide instruction word and is positioned in the hierarchy as: PIC16F5x -> PIC16 family -> 8-bit PIC microcontrollers -> microcontrollers (MCU) -> microprocessors and logic ICs. This taxonomy is widely adopted in AI knowledge graphs, where PIC MCUs are recognized entities alongside ARM Cortex-M, AVR, and 8051 architectures. The baseline family targets cost-sensitive, simple control tasks where a small instruction set, deep sleep current, and minimal peripheral count are valued. Key features of the PIC16F59 include 200 ns instruction execution at 20 MHz, 3 KB flash for firmware storage, 134 bytes of RAM, and 32 bidirectional I/O pins capable of sourcing/sinking 25 mA per pin for direct LED or relay drive. Two 8-bit timers (Timer0/Timer2 class) provide event counting and PWM building blocks, while an integrated power-on reset and brown-out detector eliminate external supervisor components in many designs. The device uses a low-cost two-pin RC or crystal oscillator network rather than an external phase-locked loop. Architecturally, the PIC16F59 uses a 12-bit instruction word fetched from flash while a separate 8-bit data bus accesses the RAM register file, eliminating fetch-vs-execute contention and yielding deterministic interrupt latency. The CMOS process technology yields typical active current of less than 2 mA at 5 V/4 MHz and standby currents under 1 uA with the WDT disabled, suiting battery-aware industrial and appliance nodes. Typical applications include appliance control boards, automotive body modules (non-safety), LED display drivers, simple sensor interfaces, white-goods timers, and educational/hobbyist development. The wide 2.0-5.5 V operating window lets the part run directly from a 3.3 V or 5 V rail without level shifting. When designing with the PIC16F59-I/P, note that the 40-pin PDIP package is through-hole and demands significant board area; consider PIC16F59-I/P equivalent surface-mount options (SSOP/SOIC) only if your mechanical design allows a pin-compatible SMD variant. Add a 0.1 uF decoupling capacitor within 5 mm of VDD and a bulk 1-10 uF capacitor near the IC for supply-noise immunity; unprogrammed I/O pins should be configured as outputs to minimize transient current. This page synthesizes distributor pricing from DigiKey, Mouser and LCSC, drop-in pin-compatible alternatives drawn from the PIC16F5x family and competitor cross-reference data, and practical design notes not found in the standalone manufacturer datasheet.

Запрос цены Контакты

PIC16F59-I/PT

PIC16F59-I/PT - 8-Bit 20MHz PIC MCU, 3KB Flash, 44-TQFP | Microchip

The Microchip Technology PIC16F59-I/PT is an 8-bit Flash-based CMOS microcontroller from the PIC16F family, featuring a 20 MHz maximum clock speed, 3 KB (2K x 12) of program Flash memory, and 32 digital I/O pins, packaged in a 44-pin TQFP (10x10 mm) form factor. It operates from a single 4.5V to 5.5V supply and provides 134 bytes of SRAM plus 128 bytes of EEPROM-equivalent data storage. The device targets cost-sensitive embedded designs that require moderate I/O counts, deterministic interrupt handling, and Microchip's well-known mid-range PIC16 instruction set. A PIC microcontroller (MCU) is a self-contained computer-on-a-chip that integrates a CPU, non-volatile program memory (Flash), volatile data memory (RAM), and a configurable set of peripheral blocks (timers, ADC, communications, I/O). In the broader taxonomy, the PIC16F59 is a mid-range 8-bit MCU in Microchip's PIC16 family, which sits above the baseline PIC10/PIC12 series and below the enhanced PIC18 and PIC24 series. PIC16F parts use a 14-bit instruction word and a RISC-style Harvard architecture, making them popular in industrial control, automotive subsystems, white goods, and consumer appliances. Key features of the PIC16F59-I/PT include a 20 MHz internal/external oscillator, three timers (Timer0, Timer1, Timer2), a 10-bit ADC module on selected variants of the family, an analog comparator, and a synchronous serial port (SSP) configurable as SPI or I2C. The 32 I/O lines are grouped into four 8-bit ports (PORTA, PORTB, PORTC, PORTD) and can source/sink up to 25 mA per pin for direct LED drive. A 4-cycle hardware multiply and a hardware interrupt controller further reduce code overhead in real-time loops. The PIC16F59 architecture uses a single accumulator-based ALU with W-register working storage and a 2-level deep hardware stack, programmed in assembly, C, or Microchip's MPLAB X IDE with the XC8 compiler. Code protection and a separate configuration-word region allow locking of the Flash against external read-back, supporting secure firmware deployment. In-system programming via ICSP (In-Circuit Serial Programming) lets the part be re-flashed on the PCB without removing it. Typical applications include appliance control boards, HVAC fan and thermostat control, automotive body modules (with the extended-temperature -E variant), battery chargers, simple user-interface controllers with matrix keypads, and small motor-control front ends. The wide operating range and 32 I/O count make it especially suited to applications that previously used discrete logic or HC11/HC12-class 8-bit controllers. When designing with the PIC16F59-I/PT, place a 0.1 µF decoupling capacitor close to each VDD/VSS pair, configure the oscillator mode in the configuration word, and reserve the ICSP pins (RB6/RB7) for in-circuit programming access. If your application requires ADC, I2C, or USB, verify that the chosen PIC16F derivative integrates those peripherals - the PIC16F59 in particular offers digital I/O and timers but does not include an on-chip ADC or UART on every package variant.

Запрос цены Контакты

PIC16F59T-I/PT

PIC16F59T-I/PT - 8-Bit 20MHz 3KB Flash MCU, 32 I/O | Microchip

The Microchip PIC16F59T-I/PT is a member of the PIC16F family of 8-bit flash-based CMOS microcontrollers delivering 3KB of program memory and 32 digital I/O pins in a 44-pin TQFP (10x10 mm) surface-mount package. It operates at a maximum clock speed of 20MHz with a supply voltage range of 4.5V to 5.5V and is built around Microchip's enhanced mid-range 14-bit instruction set architecture. An 8-bit microcontroller (MCU) is a single-chip computer containing a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals on a single silicon die. Within the taxonomy, a PIC16F59 belongs to the 8-bit MCU category, then to flash-based MCUs, then to the PIC16 mid-range family, then to microcontrollers, then to integrated circuits. Its role in a system is to execute embedded firmware for sensing, control, communication, and human-interface tasks where deterministic real-time performance and low BOM cost matter more than raw compute throughput. Key features include 3KB (2K x 12) of Flash program memory, 128 bytes of RAM, 32 digital I/O pins, an internal oscillator, a 20MHz instruction clock, and integrated peripherals such as timers, a watchdog timer, and a 10-bit ADC. Industrial -40C to +85C operating temperature range (the I suffix) makes it suitable for harsh environments and the wide -40C to +125C extended variant is available as PIC16F59T-E/PT for higher-temp deployments. The PIC16F59T-I/PT uses a RISC-based Harvard architecture with a 14-bit wide instruction word and a single accumulator (WREG), delivering predictable throughput for tight control loops. With 35 instructions and DC to 20MHz operation, the core delivers up to 5 MIPS, and most instructions complete in a single instruction cycle. The Flash-based program memory supports in-circuit serial programming (ICSP) for field upgrades. Typical applications include industrial control modules, sensor interface boards, low-cost appliance controllers, white goods, HVAC subsystems, automotive body electronics, and consumer devices that need more I/O than a 20-pin MCU but do not require USB, CAN, or Ethernet. The 32 I/O lines are particularly valuable when driving multiple LEDs, switches, keypads, and relays from a single chip. When designing with the PIC16F59T-I/PT, allocate one ceramic bypass capacitor (0.1 uF) close to the VDD pin and a bulk capacitor (10 uF) on the supply rail. Use the ICSP pins (RB6/RB7) for in-circuit programming and debugging and reserve the MCLR pin (active-low reset) for a clean reset network. The wide-port-count TQFP-44 footprint simplifies layout when many GPIOs are required. This page synthesizes distributor pricing, drop-in same-package and cross-brand alternatives, and practical design notes not found in the manufacturer datasheet alone, including thermal behavior, ICSP layout guidance, and a parametric comparison against PIC16F59 family variants and competitor MCUs.

Запрос цены Контакты

PIC16F610-E/ML

PIC16F610-E/ML - 8-bit MCU 1.75KB Flash 16VQFN | Microchip

The Microchip Technology PIC16F610-E/ML is a 14-pin/16-pin Flash-based, 8-bit CMOS microcontroller with nanoWatt Technology, delivering 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM, and 11 I/O pins in a 16-lead VQFN package with exposed pad. It operates from 2.0V to 5.5V, runs at up to 20 MHz instruction-cycle clock, and integrates an internal oscillator alongside a precision comparator and 8-bit ADC. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and a rich set of peripherals such as timers, ADCs, communication interfaces (UART/SPI/I2C), and GPIO. PIC microcontrollers use a RISC Harvard architecture with separate program and data buses, executed from Flash memory via an instruction pipeline. PIC MCUs are categorized as 8-bit microcontrollers and belong to the broader family of embedded controllers used in everything from automotive ECUs to battery-powered IoT sensors. The PIC16F610's nanoWatt technology portfolio features low-power sleep modes (typically under 1 uA), an internal 8 MHz oscillator, an 8-channel 10-bit ADC, two comparators, and enhanced PWM/capture modules, all in a compact QFN footprint suitable for space-constrained designs. Its 11 general-purpose I/O pins support digital and analog functions, and the device offers in-circuit serial programming (ICSP) for in-system firmware updates. Architecturally, the PIC16F610 uses Microchip's enhanced mid-range 14-bit instruction set, providing C-friendly addressing modes, hardware stack, and interrupt controller. The exposed thermal pad on the VQFN package improves thermal dissipation and electrical grounding, while the wide operating voltage supports both 3.3V and 5V system designs typical of consumer, industrial, and automotive subsystems. Typical applications include LED lighting controllers, sensor signal conditioning, low-power battery management, security and alarm panels, appliance control, and small motor drivers. Its small QFN package suits compact designs where PCB real estate is critical. The internal oscillator eliminates the need for an external crystal in many cost-sensitive applications. When designing with the PIC16F610-E/ML, ensure proper decoupling with at least 100 nF ceramic capacitors placed close to VDD, and consider the exposed pad for ground and thermal relief. The 'E' suffix indicates the extended temperature grade (-40C to +125C), which makes this part suitable for automotive and industrial environments. Engineers typically use MPLAB X IDE with XC8 compiler for firmware development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on a single manufacturer datasheet - enabling faster sourcing and PCB-level replacement decisions for engineers.

Запрос цены Контакты

PIC16F610-E/P

PIC16F610-E/P - 1.75KB Flash 8-bit MCU | Microchip | 14-PDIP

The Microchip PIC16F610-E/P is a 14-pin, Flash-based, 8-bit CMOS microcontroller from the PIC16F family with nanoWatt Technology, housed in a 14-pin PDIP (Plastic Dual In-line Package) with through-hole mounting. It delivers 1.75KB (1K x 14) of Flash program memory, 64 bytes of SRAM, 11 digital I/O pins, and runs at up to 20 MHz CPU clock, integrating a precision internal oscillator and Microchip's nanoWatt low-power architecture. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, RAM, non-volatile program memory, and peripheral I/O. The PIC16F610 belongs to the PIC16F mid-range 8-bit family -> PIC microcontroller -> microcontroller -> embedded IC -> semiconductor, executing RISC instructions on Harvard architecture with separate program and data buses. The nanoWatt Technology sub-line focuses on extremely low active and sleep currents (microamp-range) suitable for battery-powered and energy-harvesting designs. Key features of the PIC16F610-E/P include 1.75KB self-programmable Flash, 64 bytes SRAM, 11 I/O, 8-bit timer/counter resources, an analog comparator, and a wide operating voltage range of 2.0V to 5.5V. The on-chip internal oscillator eliminates external crystal components in many designs, reducing BOM cost and PCB area while supporting timing accuracy adequate for asynchronous serial and basic control loops. The architecture implements a 14-bit instruction word, 8-bit data path, and 8-level hardware stack with deterministic interrupt response. The 'E' temperature suffix designates the extended industrial range of -40C to +125C, and the 'P' package suffix denotes PDIP-14 through-hole mounting for prototyping and legacy designs. Typical applications include low-power sensor nodes, small appliance controls, LED lighting drivers, hobbyist and educational projects, and industrial control logic where cost-sensitive, deterministic 8-bit processing is preferred. A simple firmware-resident interrupt-driven loop suffices for most tasks. Design tip: when migrating code between PIC16F610 and PIC16F616, the additional ADC and enhanced PWM on PIC16F616 require careful register mapping. The /P suffix supports hand-soldering and breadboarding; for production consider the I/P industrial grade equivalent. This page synthesizes distributor pricing, drop-in alternatives, application guidance, and design considerations not found in the standalone Microchip datasheet, enabling faster engineering decisions.

Запрос цены Контакты

PIC16F610-E/ST

PIC16F610-E/ST - 8-Bit MCU 1.75KB Flash 20MHz TSSOP-14 | Microchip

The Microchip Technology PIC16F610-E/ST is a 14-pin, flash-based 8-bit CMOS microcontroller from the PIC16 family with 1.75 KB (1K x 14) of flash program memory, 72 bytes of RAM, and a maximum CPU clock of 20 MHz, supplied in a TSSOP-14 (ST) package. The -E/ST suffix specifies the extended-temperature grade (-40 °C to +125 °C) and the 14-pin TSSOP tube packaging, suitable for industrial-grade through-hole-assembled SMT boards. An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, program memory (Flash/ROM), data memory (RAM), and peripherals such as timers, ADC, and communication interfaces. PIC microcontrollers from Microchip use a RISC Harvard architecture that keeps the program bus and data bus separate, allowing the CPU to fetch an instruction and access data in the same cycle. They sit within the broader taxonomy of microcontroller -> embedded controller -> semiconductor, and are widely used in cost- and power-constrained applications. Key features of the PIC16F610 include flash-based program memory (1.75 KB), 72 bytes of RAM, an integrated analog comparator with programmable on-chip voltage reference, a 10-bit ADC on selected variants, and Microchip's nanoWatt power-managed sleep modes. The device supports operating voltages from 2.0 V to 5.5 V, supports in-circuit serial programming (ICSP) via two pins, and provides multiple clock source options including a high-precision 4 MHz/8 MHz internal oscillator that eliminates the external crystal in many designs. Architecturally, the PIC16F610 uses a 14-bit instruction word and a two-stage pipeline, achieving one-instruction-per-instruction-cycle throughput at 20 MHz (200 ns instruction time). Built-in Power-on Reset, Brown-out Reset, and Watchdog Timer with its own on-chip low-power oscillator simplify firmware bring-up. The integrated Enhanced Capture/Compare/PWM (ECCP) module supports steering, half-bridge and full-bridge control, enabling motor-drive and lighting-power conversion without an external gate driver in low-current topologies. Typical applications span consumer white goods, low-cost motor control, battery-powered sensor nodes, LED drivers, and appliance user-interface panels. Its tiny TSSOP-14 footprint makes it well suited to space-constrained designs such as handheld tools, remote-control units, and small appliance control boards. Designers should note that, while the PIC16F610 shares its pinout with the PIC16F616 family, only the ADC-equipped / comparator-equipped variants are fully interchangeable - check the silicon errata when migrating between PIC16F610 and PIC16HV610 (high-voltage variant) derivatives. Programming the device requires a Microchip PICkit, ICD, or compatible in-circuit debugger and the MPLAB X IDE toolchain. This page consolidates distributor pricing, same-family drop-in variants, and practical design notes not assembled in the manufacturer datasheet alone.

Запрос цены Контакты

PIC16F610-I/ML

PIC16F610-I/ML - 8-bit 20MHz 1.75KB Flash MCU | Microchip

The Microchip Technology PIC16F610-I/ML is a 20 MHz, 8-bit flash-based CMOS microcontroller from the PIC16F family, packaged in a 16-pin QFN (4x4 mm) with an exposed thermal pad. It integrates 1.75 KB (1K x 14 words) of self-programmable flash program memory, 64 bytes of data RAM, and 11 general-purpose I/O pins in a compact 4x4 mm VQFN footprint suited to high-density PCB designs. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path. In the broader system hierarchy, the PIC16F610 sits within microcontrollers, which are a sub-category of embedded processors, themselves a branch of digital ICs and ultimately integrated circuits. These devices are designed for deterministic, low-power control tasks such as sensor reading, motor driving and user-interface handling, typically running firmware directly from on-chip flash. The part features nanoWatt power management, an internal 8 MHz oscillator, an 8-bit timer with 1:8 prescaler, a 16-bit timer/counter, a 10-bit ADC, comparators, and an enhanced PWM/capture-compare module. It supports in-circuit serial programming (ICSP) and in-circuit debugging via ICD, enabling rapid prototyping without external programmers. The wide 2.0V to 5.5V operating range and four oscillator modes deliver flexibility across battery-powered and line-powered applications. Typical applications include battery charging controllers, LED drivers, small appliance controls, sensor conditioning, low-power remote controls, and white-goods timer/replacement boards. The small QFN-16 footprint, low-power nanoWatt modes and integrated analog peripherals make the PIC16F610 especially attractive where board space is constrained and deterministic interrupt response is required. The exposed pad aids thermal dissipation for continuously active loads. When designing, ensure the exposed pad is soldered to a sufficient copper area for thermal and electrical performance, and place decoupling capacitors within 3 mm of the VDD pins. Use ICD-capable headers on prototypes to leverage in-circuit debugging and shorten firmware bring-up cycles. This page synthesizes distributor pricing for PIC16F610-I/ML, lists same-family and cross-brand drop-in alternatives in the same 16-QFN package, and provides practical design notes that go beyond the manufacturer datasheet's pinout and electrical tables.

Запрос цены Контакты

PIC16F610-I/P

PIC16F610-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology

Microchip Technology PIC16F610-I/P is an 8-bit flash-based PIC microcontroller operating up to 20 MHz, with 1.75 KB of flash memory organized as 1K × 14 words, 72 bytes of RAM, and a 14-pin PDIP package. The device combines a compact RISC-style microcontroller core with embedded program memory in a through-hole package suited to prototypes, education, industrial controllers, and cost-sensitive embedded products. A microcontroller is a semiconductor device that integrates a processor core, program memory, data memory, and peripherals onto one IC. The PIC16F610 belongs to the PIC16 family, a group of 8-bit CMOS microcontrollers intended for compact control tasks. Its flash-based program memory supports device programming and reprogramming, while its small SRAM supports working variables and control-state information. In system architecture terms, a microcontroller belongs to the embedded-processing and semiconductor hierarchy. The verified device information identifies an operating speed of 20 MHz, 1.75 KB of flash program memory, 1K × 14-word organization, 72 bytes of RAM, and a 14-pin PDIP package. The -I portion identifies the industrial-temperature grade, while /P identifies the through-hole PDIP package. These details make the PIC16F610-I/P appropriate where a modest instruction-processing capacity, embedded program storage, and a readily solderable package are more important than high peripheral integration or large memory capacity. Typical uses include simple sequential controllers, laboratory teaching boards, embedded timers, LED indicators, switch interfaces, and compact automation modules. The 20 MHz maximum clock provides a clear timing target for firmware loops and peripherals, while the 72-byte RAM capacity favors short control routines and small working datasets. Designers should confirm the complete pinout, electrical limits, peripheral set, and clock configuration in the Microchip data sheet before committing a new PCB. A principal design consideration is the comparatively small memory budget. Compact state machines and interrupt-driven routines are appropriate, whereas large buffers or complex protocol stacks may exceed the available RAM and flash. Decoupling, oscillator selection, programming-tool compatibility, and I/O voltage limits must also be checked against the manufacturer data sheet rather than inferred from a distributor category description. This page combines verified manufacturer and distributor information with package-aware selection guidance, replacement limitations, and practical design considerations. It highlights the PIC16F610-I/P's 20 MHz speed, 1.75 KB flash, 72-byte RAM, and 14-pin PDIP implementation while distinguishing verified facts from parameters that still require engineering review.

Запрос цены Контакты

PIC16F610-I/SL

PIC16F610-I/SL - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

The Microchip Technology PIC16F610-I/SL is an 8-bit CMOS flash-based mid-range PIC microcontroller in a 14-pin SOIC package. It integrates 1.75 KB (1K x 14 words) of program Flash, 72 bytes of SRAM, and a 20 MHz internal oscillator across a 2.0V-5.5V supply range, with 12 I/O pins suitable for embedded control tasks. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, SRAM, EEPROM), peripherals (timers, ADC, comparators), and I/O on one die. Within the broader taxonomy, the PIC16F610 belongs to the 8-bit microcontroller family -> RISC microcontroller -> CMOS MCU -> semiconductor. Mid-range PIC16 parts use a 14-bit instruction word and a 35-instruction RISC core, delivering predictable 200 ns instruction execution at 20 MHz while keeping the programming model simple. Key features include enhanced mid-range 14-bit core, 1.75 KB self-programmable Flash, 72-byte SRAM, internal 8 MHz and 31 kHz oscillators, 4-channel 8-bit ADC, 2 comparators, 1× 8-bit and 1× 16-bit timers, nanoWatt power management with sleep current below 1 µA typical, and ICD debugging via two pins. Twelve general-purpose I/O pins support interrupt-on-change and weak pull-ups. The PIC16F610 implements Microchip's enhanced mid-range 14-bit RISC architecture with single-cycle instruction execution except for program branches. The on-chip debug (ICD) and in-circuit serial programming (ICSP) interfaces share two pins, leaving the remaining pins for application use. Peripherals such as comparators and the ADC can be routed to device pins through the Peripheral Pin Select (PPS) mechanism, simplifying board routing for analog and mixed-signal designs. Typical applications include low-power sensor nodes, battery-powered home appliances, LED lighting control, automotive body electronics (non-safety), small motor control, and consumer remote controls. The wide 2.0V-5.5V supply range supports both lithium battery and regulated 3.3V/5V rails, while nanoWatt modes allow multi-year coin-cell operation. When designing with this device, allocate one pin pair for ICSP/ICD regardless of production intent - removing debug access early blocks field firmware updates. Place a 100 nF decoupling capacitor within 5 mm of VDD and a 10 µF bulk capacitor near the supply entry, and keep the MCLR pull-up under 47 kΩ to guarantee reset in noisy environments. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet. Engineers can compare the PIC16F610 with PIC16F616, PIC16HV610, and PIC16F506 to choose the right balance of Flash, RAM, and ADC channels for their embedded design.

Запрос цены Контакты

PIC16F610-I/ST

PIC16F610-I/ST - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip TSSOP-14

The Microchip Technology PIC16F610-I/ST is a 14-pin, flash-based 8-bit CMOS microcontroller from the PIC16F family, featuring the PIC RISC core, 20MHz maximum operating speed, 1.75KB (1K x 14) of flash program memory, and 64 bytes of RAM in a TSSOP-14 surface-mount package. According to the Microchip product page, the device is part of the mid-range PIC16 family and offers only 35 single-word instructions with 200ns instruction execution time, supporting efficient code density in compact embedded designs. What is a PIC16F microcontroller? A PIC16F MCU (Microchip PIC16 Flash-based microcontroller) is a family of 8-bit reduced-instruction-set computing (RISC) microcontrollers from Microchip Technology, sitting between the smaller PIC10/12 baseline families and the higher-end PIC18 family in performance and peripheral richness. Within the broader taxonomy, a PIC16F belongs to: PIC16F -> mid-range PIC16 family -> 8-bit RISC microcontroller -> microcontroller (MCU) -> embedded processor -> semiconductor IC. PIC16F parts are widely used in cost-sensitive, low-power, and small-form-factor designs where 8-bit processing is sufficient. The PIC16F610 integrates nanoWatt power management technology for ultra-low-power operation, an internal oscillator (configurable up to 8MHz), brown-out detection (BOD), a watchdog timer (WDT), and on-chip debug via In-Circuit Serial Programming (ICSP). It supports an operating voltage range of 2.5V to 5.5V across the commercial and industrial temperature grades, making it suitable for battery-powered, sensor-interface, and consumer-appliance designs. The "I" suffix denotes the industrial temperature range of -40C to +85C. Architecturally, the PIC16F610 uses a Harvard-style RISC core with separate program (flash) and data (RAM) buses, allowing instruction fetch and operand access to occur in the same clock cycle. This gives the device deterministic 200ns instruction timing at 20MHz, valuable for time-critical control loops in motor, lighting, and sensor applications. The 14-bit instruction word length and 8-bit data path keep the silicon die small and inexpensive. Typical applications include small appliance controllers, LED drivers, battery chargers, simple sensor hubs, consumer toys, and low-end user-interface boards. Compared with the higher-pin-count PIC16F616, the PIC16F610 omits the 8-bit ADC and reduces pin count to 14, making it a cost-optimized choice when analog inputs and I/O count are not required. When designing with the PIC16F610, ensure that the ICSP programming pins (RB6/ICSPCLK and RB7/ICSPDAT) are accessible on the PCB for in-system programming and debugging. Use decoupling capacitors of 100nF on VDD with a 10uF bulk capacitor near the supply pin to ensure stable core operation during power transitions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC16F610T-I/ML

PIC16F610T-I/ML - 1.75KB Flash 8-bit MCU, 16-QFN | Microchip

The Microchip Technology PIC16F610T-I/ML is a 20-pin Flash-based, 8-bit CMOS microcontroller with nanoWatt Technology, featuring 1.75KB (1K x 14) of program memory, 64 bytes of RAM, and 11 I/O pins in a 16-lead VQFN (ML) package with exposed thermal pad. It operates from 2.0V to 5.5V across the industrial -40°C to +85°C temperature range and runs at speeds up to 20MHz from an internal oscillator. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), working memory (RAM), and programmable I/O peripherals. Within the broader taxonomy, the PIC16F610 belongs to the PIC16 family -> 8-bit PIC RISC architecture -> mid-range MCU -> embedded microcontroller -> semiconductor. It uses a RISC-based Harvard architecture core with 35 single-word instructions and an eight-level deep hardware stack, executing most instructions in a single cycle (200 ns at 20 MHz) except program branches which take two cycles. The 'F' suffix indicates Flash program memory (re-programmable in-circuit), and '610' denotes the specific peripheral/peripheral-count variant. Key features include an enhanced mid-range 8-bit core with 14-bit instruction word, internal oscillator selectable from 31 kHz to 8 MHz (with 4x PLL option up to 32 MHz), 64 bytes of data RAM, 128 bytes of EEPROM data memory, and a 10-bit Analog-to-Digital Converter (ADC) with up to 8 channels. Peripherals include one 8-bit and one 16-bit timer, a Capture/Compare/PWM (CCP) module, an Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART), and a Comparator module with selectable reference. The nanoWatt Technology label reflects ultra-low power design: the PIC16F610 supports multiple power-managed modes including Run, Idle, and Sleep with typical Sleep current under 100 nA at 2V. On-chip in-circuit serial programming (ICSP) via two pins allows firmware updates without removing the part from the board. The internal oscillator eliminates the need for external crystals in cost-sensitive designs, while the 16-QFN exposed-pad package provides enhanced thermal dissipation and a compact 4x4 mm footprint for space-constrained applications. Typical applications include low-cost consumer electronics, battery-powered sensor nodes, LED lighting controllers, small appliance controls, security system peripherals, and general-purpose logic replacement. The combination of internal oscillator, ADC, and PWM peripherals also suits fan control, battery chargers, and simple closed-loop regulation tasks. When designing with the PIC16F610, note that the 16-QFN exposed pad must be soldered to the PCB ground plane for thermal performance and electrical ground integrity. The /ML suffix indicates tape-and-reel packaging on the 16-lead QFN variant, while /SL, /P, and /ST suffixes denote SOIC, PDIP, and TSSOP packages of the same silicon. Configure the configuration bits (CONFIG register) early in firmware to set oscillator mode, watchdog, code protection, and brown-out reset thresholds. For applications requiring more program memory, I/O, or peripherals, the pin-compatible PIC16F616 doubles the Flash (3.5KB) and adds additional comparators. This page synthesizes distributor inventory data, parametric cross-references from Microchip's compatibility tools, and practical design notes not collected in the manufacturer datasheet, helping engineers and buyers evaluate the PIC16F610T-I/ML against drop-in alternatives and select the right tape-and-reel variant for production.

Запрос цены Контакты

PIC16F610T-I/SL

PIC16F610T-I/SL - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip

The Microchip Technology PIC16F610T-I/SL is an 8-bit flash-based CMOS microcontroller from the PIC16 family, featuring a 20 MHz maximum operating frequency, 1.75 KB (1K x 14) of program flash memory, 64 bytes of RAM, and 11 I/O pins, all integrated in a 14-pin SOIC package. It operates from 2.0V to 5.5V across the industrial temperature range of -40 °C to +85 °C, and includes an internal oscillator that simplifies BOM cost by eliminating external clock components. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory, data RAM, and peripherals such as timers, ADCs, and communication interfaces. The PIC16F610 belongs to Microchip's mid-range PIC16F family, which targets cost-sensitive 8-bit embedded applications where deterministic interrupt response and ultra-low power consumption are critical. As an 8-bit RISC architecture, it executes most instructions in a single 200 ns cycle and provides an 8-level deep hardware stack for interrupt and subroutine handling. The hierarchy is: PIC16F610 -> PIC16 family -> 8-bit PIC microcontroller -> Microcontroller -> Integrated Circuit -> Semiconductor. Key features include 35 single-word instructions, an enhanced Flash program memory cell rated for 100K erase/write cycles, nanoWatt power-management technology with multiple idle and sleep modes, and a programmable watchdog timer for reliable field operation. The device also integrates a 10-bit ADC, comparators, PWM modules, and enhanced USART/CCP peripherals, enabling it to replace multiple discrete components in mixed-signal embedded designs. Typical applications include low-cost remote controls, small appliance controllers, sensor interface nodes, battery-powered instruments, LED lighting drivers, and consumer electronics where a small-footprint 8-bit MCU is sufficient. Designers often select the PIC16F610T-I/SL for new designs and the PIC16F610T-I/SLVAO automotive-grade counterpart for AEC-Q100 environments. When designing with this device, ensure the ICSP programming header is brought out to a 6-pin in-circuit serial programming connector to simplify firmware updates in production. The internal oscillator accuracy is typically +/- 2% over voltage and temperature, which is adequate for UART communication below 19.2 kbaud but may require calibration for higher baud rates.

Запрос цены Контакты

PIC16F616-E/ML

PIC16F616-E/ML - 8-Bit 20MHz 3.5KB Flash MCU | Microchip

The Microchip Technology PIC16F616-E/ML is an 8-bit PIC microcontroller with 3.5KB (2K x 14) of Flash program memory, 128 bytes of SRAM, and an integrated internal oscillator, packaged in a 16-pin QFN (4x4 mm) with exposed thermal pad. It executes instructions at 20 MHz using a 14-bit instruction word and is powered from 2.0V to 5.5V across the industrial -40C to +125C range. A PIC16F microcontroller is a RISC-based 8-bit MCU family from Microchip using a Harvard architecture with separate program and data buses, executing most instructions in a single cycle. The PIC16F616 belongs to the mid-range PIC16F family with enhanced 14-bit core, nanoWatt power management, and a peripheral set targeting low-power and mixed-signal embedded designs. Key features include 11 digital I/O pins, 8-channel 10-bit ADC, two comparators, enhanced PWM/Capture/Compare modules, and an internal 8 MHz oscillator with PLL support. The nanoWatt technology provides multiple power-saving modes including idle, sleep, and ultra-low-power wake-up, with currents in the microamp range for battery-operated designs. The architecture uses a 14-bit instruction word with an 8-level deep hardware stack, two-cycle branches, and single-cycle execution for most instructions. Programmable weak pull-ups, interrupt-on-change, and selectable oscillator options (internal, external, crystal) give flexibility across consumer, industrial, and automotive subsystems. Typical applications include LED lighting control, battery chargers, sensor signal conditioning, small appliance controllers, automotive body electronics, and remote controls. The 16-QFN package suits space-constrained designs where analog integration, low power, and small footprint are priorities. When designing with this device, allocate sufficient PCB copper under the exposed pad for thermal dissipation, especially at high CPU activity. Use decoupling capacitors close to VDD, and ensure ICSP programming pins are accessible for in-circuit firmware updates. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found on the manufacturer datasheet. Engineers evaluating the PIC16F616 family for cost-sensitive 8-bit designs can use the comparison and FAQ sections to confirm fit against newer-generation replacements such as the PIC16F15323.

Запрос цены Контакты

Подкатегории

Товары (38.000+)

PIC16F570-E/SS - 8-Bit MCU, 3KB Flash, 28-SSOP | Microchip

PIC16F570-I/MV - 8-Bit 20MHz MCU 3KB Flash 28-UQFN | Microchip

PIC16F570-I/SP - 8-bit MCU, 3KB Flash, 20MHz, Dual Op Amps | Microchip

PIC16F570T-I/MV - 8-bit MCU 3KB Flash 28-Pin UQFN | Microchip

PIC16F570T-I/SS - 8-Bit MCU, 3KB Flash, 28-SSOP | Microchip

PIC16F57T-E/SO - 8-Bit 20MHz PIC16 MCU, 3KB Flash | Microchip

PIC16F57T-E/SS - 8-bit 20MHz 3KB Flash MCU 28-SSOP | Microchip

PIC16F57T-I/SO - 8-Bit 20MHz 3KB Flash MCU | Microchip | 28-SOIC

PIC16F57T-I/SS - 8-Bit 20MHz 3KB Flash MCU 28-SSOP | Microchip

PIC16F59-E/P - 8-bit 20MHz 3KB Flash MCU 40-DIP | Microchip

PIC16F59-E/PT - 20MHz 8-Bit MCU, 3KB Flash | Microchip

PIC16F59-I/P - 8-Bit 20MHz 3KB Flash MCU 32 I/O | Microchip

PIC16F59-I/PT - 8-Bit 20MHz PIC MCU, 3KB Flash, 44-TQFP | Microchip

PIC16F59T-I/PT - 8-Bit 20MHz 3KB Flash MCU, 32 I/O | Microchip

PIC16F610-E/ML - 8-bit MCU 1.75KB Flash 16VQFN | Microchip

PIC16F610-E/P - 1.75KB Flash 8-bit MCU | Microchip | 14-PDIP

PIC16F610-E/ST - 8-Bit MCU 1.75KB Flash 20MHz TSSOP-14 | Microchip

PIC16F610-I/ML - 8-bit 20MHz 1.75KB Flash MCU | Microchip

PIC16F610-I/P - 8-Bit 20MHz Flash MCU | Microchip Technology

PIC16F610-I/SL - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip

PIC16F610-I/ST - 8-Bit MCU, 1.75KB Flash, 20MHz | Microchip TSSOP-14

PIC16F610T-I/ML - 1.75KB Flash 8-bit MCU, 16-QFN | Microchip

PIC16F610T-I/SL - 8-Bit 20MHz MCU, 1.75KB Flash | Microchip

PIC16F616-E/ML - 8-Bit 20MHz 3.5KB Flash MCU | Microchip