Интегральные схемы

PIC18F56K42-E/PT

PIC18F56K42-E/PT - 8-Bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F56K42-E/PT is an 8-bit PIC microcontroller from the PIC18(L)FxxK42 family, featuring a 64 MHz CPU, 64 KB Flash program memory, 4 KB SRAM, and 1 KB EEPROM, housed in a 48-pin TQFP-EP (7x7 mm) package with exposed thermal pad. It operates from 2.3V to 5.5V across the -40C to +125C extended industrial temperature range, making it suitable for both consumer and harsh-environment embedded applications. An 8-bit PIC microcontroller is a Harvard-architecture CMOS MCU that executes a RISC-like instruction set on 8-bit data while allowing 16-bit-wide program memory fetches, providing predictable timing and deterministic interrupt response. The PIC18 family sits at the top of Microchip's 8-bit portfolio as a high-performance tier, positioned above PIC16 and PIC10/12/14/15 families and below the dsPIC and PIC32 32-bit lines. The K42 sub-family adds Core Independent Peripherals (CIPs) such as CLC, NCO, PWM, and ADC with Computation (ADC2) that operate without CPU intervention, enabling low-power and real-time control designs. Key features of the PIC18F56K42 include 12-bit ADC with up to 35 external channels, 5-bit DAC, 8-bit DAC reference, hardware CVD for capacitive touch, four 16-bit timers, two I2C, two SPI, two UART, and 44 dedicated I/O pins. The integrated charge pump improves ADC accuracy at low VDD, while the XLP (eXtreme Low Power) technology enables deep Sleep currents down to sub-microamp levels with retention. Architecturally, the device combines a 16-bit program bus, 8-bit data bus, single-cycle hardware multiplier, and a vectored interrupt controller. CIPs such as CLC, NCO, and PWM with complementary outputs are interconnected via a fabric-like routing matrix, allowing analog and timing functions to be wired together in hardware and reducing firmware load. Typical applications include industrial control panels, home appliances, motor control BLDC drivers, capacitive touch user interfaces, IoT sensor nodes, and automotive body and convenience modules. The extended temperature grade (-E) supports under-hood and outdoor deployments. Designers should pay attention to VDD/VSS decoupling: place a 100 nF X7R ceramic as close as possible to each power pin pair and a bulk 10 uF tantalum or ceramic on the main rail. The exposed pad on TQFP-EP must be soldered to the ground plane for thermal dissipation and electrical reference. This page synthesizes distributor pricing, drop-in PIC18FxxK42 alternatives, and practical design notes not found in the manufacturer datasheet alone, helping procurement and firmware engineers make informed selection decisions.

Запрос цены Контакты

PIC18F56K42-I/MV

PIC18F56K42-I/MV - 64KB Flash 8-bit MCU 48-UQFN | Microchip

The Microchip Technology PIC18F56K42-I/MV is an 8-bit PIC18 XLP microcontroller running at 64 MHz, integrating 64 KB of Flash, 4 KB of RAM, and 256 B of EEPROM in a 48-pin UQFN (MV) 6x6 mm package. It belongs to the PIC18(L)FxxK42 family of highly integrated, low-power, high-performance MCUs designed for embedded designs that need both advanced analog and core-independent peripherals. A microcontroller (MCU) is a single-chip computer containing a CPU core, non-volatile program memory (Flash), volatile working memory (RAM), and a range of peripheral interfaces. The PIC18 architecture is an 8-bit Harvard RISC core from Microchip with an enhanced instruction set, a hardware multiplier, and prioritized vector interrupts. In the broader taxonomy, an MCU is a type of microcontroller, which itself falls under microcontrollers and processors in the embedded semiconductor category. The 56K42 specifically belongs to the PIC18(L)FxxK42 subfamily, which sits above general PIC16 parts in complexity and below the 16-bit dsPIC/PIC24 and 32-bit PIC32 families. Key features of the PIC18F56K42 include the 12-bit Analog-to-Digital Converter with Computation (ADC2) - offering up to 35 external channels with automated oversampling, averaging, filtering, and threshold comparison. The integrated Hardware Capacitive Voltage Divider (CVD) supports mTouch capacitive touch sensing without external components. The device also includes Direct Memory Access (DMA) controllers, vector interrupts, a Digital-to-Analog Converter (DAC), comparators, configurable PWMs (CCP/ECCP), and the Device Information Area (DIA) for unique serial numbers and calibration constants. The PIC18F56K42 implements Microchip's eXtreme Low Power (XLP) technology with multiple low-power modes (Sleep, Idle, Doze), a peripheral module disable feature, and an integrated charge pump that allows the 12-bit ADC to operate down to 1.8V VDD. The 48-pin UQFN package exposes up to 41 I/O pins with interrupt-on-change support and high-current sink/source capability on selected pins. The 64 MHz FOSC (16 MIPS at 4 clocks per instruction) gives ample headroom for sensor fusion, motor control loops, and protocol stacks. Typical applications include industrial control, IoT sensor nodes, home automation, capacitive touch user interfaces, low-power battery-powered instrumentation, and small motor or lighting control. The combination of large memory, advanced analog, and XLP technology makes it well suited to applications that demand both signal conditioning and ultra-low standby current. When designing with this device, use the MPLAB X IDE and MPLAB Code Configurator (MCC) to generate peripheral drivers and pin configurations. Always review the device errata for the specific silicon revision used in production, and consider migrating to the -E/-F temperature grades or QFP packages (such as PIC18F56K42-I/PT) if thermal dissipation or hand-rework is required. This page synthesizes distributor pricing, drop-in alternatives drawn from the PIC18(L)FxxK42 family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F56K42T-I/MV

PIC18F56K42T-I/MV - 8-Bit 64MHz 64KB Flash XLP MCU | Microchip

The Microchip Technology PIC18F56K42T-I/MV is a PIC18F "K42" family 8-bit microcontroller built on an enhanced Harvard RISC architecture, delivering 64 MHz (16 MIPS) CPU performance from 64 KB of on-chip Flash, 4 KB of SRAM and 256 B of EEPROM. The T-suffix indicates tape-and-reel packaging and the I-suffix denotes an industrial -40C to +85C operating range, while MV identifies the lead-free 48-pin UQFN 6x6 mm exposed-pad package. The device targets ultra-low-power XLP applications with nanoWatt XLP technology, integrated core-independent peripherals (CIPs) and intelligent analog blocks. An 8-bit PIC microcontroller (MCU) is a single-chip computer based on Microchip's proprietary Harvard architecture that separates program and data memory for deterministic instruction execution, with the K42 family positioned in the ultra-low-power XLP segment between the smaller K20 and K40 predecessors and the newer Q-series successors. In the broader hierarchy: PIC18F -> 8-bit PIC -> PIC MCU -> microcontroller -> embedded system -> semiconductor IC. The K42 family spans 28/40/48-pin packages, allowing the same firmware and development tools to scale from compact sensor nodes to feature-rich control boards. Differentiating features of the PIC18F56K42 include a 12-bit ADC2 (Analog-to-Digital Converter with Computation) with up to 35 external channels and an integrated charge pump, a hardware Capacitive Voltage Divider (CVD) for mTouch touch sensing, four 16-bit timers with built-in PWM, two USART, two SPI, two I2C and up to 36 interrupt sources. The device also integrates a 32-level hardware CRC, a Direct Memory Access (DMA) controller with 4 channels, a Windowed Watchdog Timer (WWDT) and a Vectored Interrupt module with a hardware Interrupt-on-Change (IOC) for low-latency GPIO response. The architecture combines a modified 8-bit data path with a 16-bit instruction word, providing C-compiler-friendly orthogonal addressing while retaining deterministic real-time behavior. The XLP nanoWatt technology achieves typical sleep currents below 50 nA with RAM retention, and a power-managed idle/doze mode that lets peripherals run while the CPU is gated. Charge-pump-assisted ADC2 operation allows analog conversion down to 1.8 V supply, simplifying battery-monitor designs and low-battery warning thresholds. Typical applications include IoT edge nodes, home-automation and smart-home hubs, low-power wireless sensor platforms (LoRa/BLE host MCUs), consumer appliances with capacitive touch HMIs, automotive body and interior modules, and industrial control boards requiring deterministic 8-bit GPIO-driven control. Designers typically select this device when they need deterministic interrupt response, mature MPLAB X IDE support, and a pin migration path within the same K42 family. When laying out the PCB, treat the central UQFN exposed pad as the primary thermal and electrical ground path - solder it directly to a continuous ground pour with thermal vias for thermal resistance below 30 C/W. Use the MPLAB Code Configurator (MCC) to generate CIP setup, and always include a 0.1 uF decoupling capacitor within 3 mm of each VDD pin pair to minimize switching noise on the analog rails. This page synthesizes the manufacturer datasheet, distributor pricing tiers, drop-in K42-family alternatives and practical design notes to give the engineer a single, citable reference that distributor product pages do not provide.

Запрос цены Контакты

PIC18F56Q43-E/6LX

PIC18F56Q43-E/6LX - 8-bit 64MHz 64KB Flash MCU | Microchip

The Microchip Technology PIC18F56Q43-E/6LX is an 8-bit PIC18 microcontroller from the PIC18-Q43 family, integrating 64 KB of Flash program memory, 4 KB of SRAM and a 64 MHz internal oscillator in a 48-pin VQFN (6x6 mm) package. The -E suffix denotes the -40C to +125C extended operating temperature grade required for industrial and automotive-grade designs. An 8-bit microcontroller (MCU) is a programmable computing device built around a CPU, program memory and data memory on a single silicon die, optimized for deterministic real-time control, low power consumption, and a rich set of on-chip peripherals. The PIC18-Q43 family combines Microchip's most popular Core Independent Peripherals with new interconnection fabric so that hardware customization no longer requires complex firmware. The product type hierarchy is: MCU -> microcontroller -> 8-bit microcontroller -> PIC18 microcontroller -> PIC18-Q43 family -> power management/real-time control IC. Key features of the PIC18F56Q43 include six Direct Memory Access (DMA) controllers that move data without CPU intervention, three 16-bit dual PWMs giving six PWM outputs for motor and power conversion control, a 12-bit Analog-to-Digital Converter with Computation (ADCC) supporting Capacitive Voltage Divider (CVD) touch sensing, a vectored interrupt controller with selectable priorities and fixed three-cycle latency, and a Zero-Cross Detect (ZCD) peripheral. The device also includes five UARTs (one with LIN/DMX/DALI support), configurable logic cells (CLCs), and a 1.024/2.048/4.096 V voltage reference. Typical applications include industrial motor control, LED lighting and dimming, capacitive touch user interfaces, automotive body and sensor nodes, white-goods and small appliance control, and USB-to-UART bridge designs. The wide 1.8V to 5.5V operating range and low-power XLP technology make the part suitable for battery-backed appliances that must run from coin cells or 2xAA chemistries while still delivering 64 MIPS throughput.

Запрос цены Контакты

PIC18F56Q43T-I/PT

PIC18F56Q43T-I/PT - 64KB Flash, 48-TQFP 8-bit MCU | Microchip

The Microchip Technology PIC18F56Q43T-I/PT is an 8-bit PIC microcontroller in the PIC18-Q43 family, providing 64KB of Flash program memory, 4KB of RAM, and 1KB of EEPROM, housed in a 48-pin TQFP (7x7 mm) package. It operates up to 64MHz from a 1.8V to 5.5V supply, integrates Core Independent Peripherals, a 12-bit ADCC, three 16-bit PWMs, a 6-channel DMA, and an 8-bit DAC for real-time control tasks. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash), volatile data memory (RAM), non-volatile storage (EEPROM), and a rich set of on-chip peripherals. The 8-bit PIC architecture from Microchip Technology is positioned in the taxonomy: 8-bit MCU -> microcontroller -> embedded processor -> semiconductor. The PIC18-Q43 family emphasizes Core Independent Peripherals (CIPs) that operate without CPU intervention, reducing firmware complexity and deterministic latency for real-time control loops. Key features include 64KB Flash, 4KB RAM, 1KB EEPROM, up to 64MHz operation across -40C to +85C industrial temperature range, integrated 12-bit ADC with Computation (ADCC) supporting capacitive voltage divider (CVD) touch sensing, three independent 16-bit PWM channels with complementary outputs, a 6-channel DMA engine, peripheral pin select (PPS) for flexible signal routing, and 5V tolerant I/O. The TQFP-48 package supports surface-mount assembly with industry-standard 0.5mm pitch. The PIC18F56Q43 uses an enhanced Harvard RISC architecture with a modified instruction set that allows 16-bit opcodes and a hardware multiplier. The ADCC module performs hardware-averaged oversampling and threshold comparison autonomously, while the unified PWM engine supports edge/center alignment for motor, lighting, and power-conversion control. The integrated DMA engine transfers data between peripherals and memory without CPU involvement, ideal for high-throughput sensor or communication links. Typical applications include industrial automation and motor control, IoT edge nodes, capacitive touch user interfaces, LED lighting controllers, sensor hubs, and small home appliances. The XLP (eXtreme Low Power) feature set targets battery-powered IoT deployments. When designing with this device, observe the decoupling network (100nF + 1uF at VDD/AVDD) and follow the Microchip MPLAB development flow with PICkit or ICD programmers. The wide operating voltage (1.8V to 5.5V) supports both 3.3V and 5V system rails with no level translation required for the digital I/O. This page synthesizes distributor pricing, same-package PIC18 drop-in alternatives, and practical design notes that complement the manufacturer datasheet.

Запрос цены Контакты

PIC18F57K42-E/MV

PIC18F57K42-E/MV - 64MHz 8-bit MCU, 128KB Flash, 48-UQFN | Microchip

The Microchip Technology PIC18F57K42-E/MV is a high-performance 8-bit PIC microcontroller from the PIC18FxxK42 family, integrating core independent peripherals, intelligent analog peripherals, and large Flash/RAM/EEPROM memories. The device operates at up to 64MHz, features 128KB (64K x 16) of Flash program memory, 8KB RAM, and 256B EEPROM in a compact 48-pin UQFN (6x6 mm) package (MV). The -E suffix denotes the extended operating temperature range of -40C to +125C, suitable for industrial and harsh-environment deployments. An 8-bit microcontroller (MCU) is a programmable embedded processor that integrates a CPU, memory, and peripherals onto a single silicon die. The PIC18 family sits at the top of Microchip's 8-bit portfolio, sitting between baseline PIC10/12/16 parts and higher-end dsPIC/32-bit families. The PIC18FxxK42 series specifically targets low-power (XLP) applications with rich analog integration including 12-bit ADC2 with computation, DAC, comparators, and op amps, alongside DMA, vector interrupts, and configurable logic cells (CLC). Key features of the PIC18F57K42 include the 12-bit ADC2 module with automatic averaging and threshold scanning, multiple SPI/I2C/UART interfaces with LIN support, DMA controllers for offloading the CPU, and PWM/CCP modules for motor and power control. The device includes 44 user I/O pins with peripheral pin select (PPS) for flexible signal routing. Core independent peripherals allow sensor interfacing and signal generation without CPU intervention, lowering active time and overall power consumption. The XLP (eXtreme Low Power) technology brings deep sleep currents under 50nA with retention RAM. From an architectural standpoint, the PIC18F57K42 uses a 16-bit modified Harvard architecture with separate program and data buses, executing most instructions in a single cycle. The 128KB Flash supports self-programmability via ICSP, and 256B of EEPROM provides non-volatile data storage. The 8KB SRAM includes 1KB of retention RAM that survives sleep modes for state preservation. Typical applications include industrial sensor nodes, motor control drives, IoT edge devices, building automation, HVAC control, low-power wireless sensor hubs, and consumer appliances. The combination of USB-less 48-pin density, 64MHz performance, and large memory makes it ideal for protocol-rich appliances and IoT gateways. Designers favor it for code-density, deterministic interrupt latency, and Microchip's mature MPLAB X toolchain with XC8 compiler support. When designing with the PIC18F57K42-E/MV, ensure the UQFN-48 PCB footprint includes thermal pad soldering per IPC-7351 for heat dissipation, and follow Microchip's AN2644 application note for optimal XLP sleep-mode configuration. The 48-UQFN MV package has tight pad pitch - 0.4mm spacing - so stencil design and reflow profile must be controlled during assembly. This page consolidates distributor pricing, drop-in alternatives within the PIC18FxxK42 family and cross-brand 8-bit MCU options, and practical design notes that go beyond the manufacturer datasheet to support component selection, sourcing, and PCB layout decisions.

Запрос цены Контакты

PIC18F57K42-I/PT

PIC18F57K42-I/PT - 128KB Flash, 64MHz 8-bit MCU | Microchip

The Microchip PIC18F57K42-I/PT is a high-performance 8-bit PIC microcontroller from the PIC18FxxK42 family, integrating 128KB of Flash program memory, 8KB of SRAM, and 256B of EEPROM in a 48-pin TQFP-EP package (7x7 mm) with an exposed thermal pad. It executes instructions at up to 64 MHz, delivering 16 MIPS of throughput, and integrates Core Independent Peripherals (CIPs) such as CWG, NCO, DSM, and Configurable Logic Cells that offload tasks from the CPU. A microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory, volatile data memory, and on-chip peripherals such as timers, communication interfaces, and analog converters. PIC18F-family devices sit at the high-performance tier of Microchip's 8-bit portfolio, between baseline PIC10/PIC12/PIC16 mid-range parts and the 16-bit PIC24/dsPIC families - well suited for applications that need more code space and richer peripherals than a PIC16 can provide, but where a 32-bit Cortex-M0/M0+ would add cost and complexity. Key features of this variant include a 12-bit ADC2 (with computation), a 5-bit DAC, two comparators with 8-bit reference, multiple hardware PWM channels, DMA between memory and peripherals, vector interrupts for fast response, a Math Accelerator (MAP) for hardware multiply/divide, and a Device Information Area (DIA) for unique ID and calibration constants. The wide 2.3V to 5.5V VDD range and XLP (eXtreme Low-Power) technology allow deep sleep currents down to 50 nA with fast wake-up, targeting battery- and energy-harvesting designs. Internally, the device uses a 16-bit modified-Harvard architecture with a 32-level hardware stack, hardware multiply/divide, indirect/post-increment addressing modes, and a 64 MHz internal oscillator selectable by software. The DMA controller can move data between peripherals and RAM without CPU intervention, while Vector Interrupts reduce latency by jumping directly to the handler. These architectural choices allow developers to consolidate what would normally be done in external logic or software loops into the chip itself. Typical use cases include industrial control panels, IoT sensor nodes with low-power duty-cycled radios, motor control with field-oriented control (FOC) for BLDC, USB human-interface devices (HID/CDC), and white-goods or HVAC controllers. The 48-pin TQFP footprint also suits quick migration from PIC18F47K42 designs that require the larger 128KB memory tier without changing PCB layout. The TQFP-EP package provides a thermal pad that improves heat spreading for full-speed operation across the industrial -40C to +85C range. When designing with this MCU, allow the exposed thermal pad (pin 49) to be soldered to a copper pour of at least 1 square inch on both top and bottom layers to meet the 64 MHz operating point reliably. Use MPLAB X IDE with the XC8 compiler to take advantage of DIA and the hardware Math Accelerator. This page consolidates distributor pricing, drop-in alternatives, and practical design notes that complement the manufacturer datasheet for engineers evaluating the PIC18F57K42-I/PT for new designs and field replacements.

Запрос цены Контакты

PIC18F57K42T-I/MV

PIC18F57K42T-I/MV - 64MHz 8-Bit 128KB Flash MCU | Microchip

The Microchip Technology PIC18F57K42T-I/MV is an 8-bit PIC18 XLP microcontroller featuring a 64MHz CPU, 128KB Flash program memory, 8KB SRAM, and 256B EEPROM, housed in a 48-pin UQFN (MV) 6x6mm package with an exposed thermal pad. It belongs to the PIC18(L)FxxK42 family and integrates a rich set of core-independent peripherals, intelligent analog peripherals, and large Flash/RAM/EEPROM memories designed for low-power high-performance embedded applications. A microcontroller (MCU) is a single-chip computer that contains a CPU core, program and data memory, peripherals, and I/O. The PIC18 architecture is an enhanced 8-bit Harvard RISC core with a hardware multiplier, 31-level stack, and vectored interrupts. The XLP (eXtreme Low Power) designation indicates this family is engineered for battery-powered and energy-harvesting designs, drawing nano-amp currents in Sleep mode. Key features include a 12-bit ADC2 with up to 35 external channels and 140 ksps throughput, hardware CVD (Capacitive Voltage Divider), DMA, vector interrupts, multiple UART/SPI/I2C interfaces, configurable PWM, comparators, DAC outputs, and an 8-bit core-independent peripheral set. The 64MHz internal oscillator, programmable prescaler, and 4x PLL provide flexible clocking. Operating voltage spans 2.3V to 5.5V with industrial -40C to +85C support. The K42 architecture integrates Direct Memory Access (DMA) into the 8-bit core, allowing data movement between peripherals and memory without CPU intervention. The ADC2 module adds hardware oversampling, averaging, and threshold comparisons so analog signal conditioning runs autonomously. Hardware CVD enables robust touch and proximity sensing. Typical applications include IoT sensor nodes, home appliances, motor control, LED lighting, capacitive touch user interfaces, industrial control, USB device functions, and battery-powered metering. The wide peripheral set makes the device suitable as a system-on-chip in cost-sensitive designs. When designing with this MCU, allocate decoupling capacitors close to each VDD pin, follow Microchip's UQFN PCB layout recommendations for the exposed pad, and use the MPLAB X IDE with the XC8 compiler. Verify signal integrity on high-speed communication lines and refer to Microchip ANs for DMA and ADC2 usage. This page synthesizes distributor pricing, drop-in same-package alternatives, and practical engineering design notes not found in the manufacturer datasheet alone, offering actionable intelligence for sourcing and design decisions.

Запрос цены Контакты

PIC18F57Q43-E/6LX

PIC18F57Q43-E/6LX - 128KB Flash 8-bit MCU, 64MHz, 48-VQFN | Microchip

The Microchip PIC18F57Q43-E/6LX is an 8-bit RISC microcontroller from the PIC18-Q43 family, integrating 128 KB of Flash program memory, 8 KB of SRAM and 1 KB of EEPROM, and operating at a maximum clock of 64 MHz. It is housed in a 48-pin VQFN (6x6 mm) package with an exposed thermal pad, and carries the extended (-40C to +125C) operating temperature grade indicated by the -E suffix. An 8-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU, non-volatile program memory, volatile data memory, and configurable peripherals on a single silicon die. The PIC18-Q43 family specifically augments this classic architecture with Core Independent Peripherals (CIPs), six Direct Memory Access (DMA) controllers, Configurable Logic Cells (CLCs), and a 12-bit Analog-to-Digital Converter with Computation (ADCC). These features allow real-time control tasks such as capacitive touch sensing, power conversion, and motor control to be offloaded from the CPU into dedicated hardware, reducing firmware complexity and latency. Key features of the PIC18F57Q43-E/6LX include three 16-bit dual PWMs providing six PWM outputs, an 8-bit DAC, multiple comparators with a Zero-Cross Detect (ZCD) module, fixed voltage references of 1.024 V, 2.048 V and 4.096 V, five UARTs (one supporting LIN/DMX/DALI), and vectored interrupts with programmable priority. The on-chip DMA engine moves data between peripherals and memory without CPU intervention, freeing instruction cycles for application logic. The device architecture is built on Microchip's enhanced PIC18 Harvard pipeline, with selectable internal oscillator blocks, multiple I/O ports, and functional safety (FuSa) features for safety-critical designs. Peripherals are interconnected through the Peripheral Pin Select (PPS) system, allowing most digital functions to be remapped to a wide range of physical pins. Typical applications include industrial control, IoT edge nodes, consumer appliances, building automation, automotive body and lighting subsystems, and USB-to-UART bridges when paired with an external transceiver. The combination of high Flash density and CIPs also suits advanced sensor hubs and BLDC/PMSM motor drive controllers. When designing with this part, pay attention to decoupling: place 100 nF and 1 uF ceramics adjacent to the VDD/VSS pairs, route the exposed pad to a continuous ground plane, and confirm unused I/O pins are configured as outputs low or as inputs with internal pull-ups. The functional safety documentation set should be reviewed for any IEC 61508 or ISO 26262 target. This page synthesizes distributor pricing, parametric alternatives, and practical design considerations for the PIC18F57Q43-E/6LX that go beyond the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F57Q43-I/PT

PIC18F57Q43-I/PT - 8-Bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F57Q43-I/PT is an 8-bit PIC microcontroller from the PIC18-Q43 family, featuring 128KB of Flash, 8KB of RAM, and 1KB of EEPROM in a 48-pin TQFP-EP (7x7mm) package with an exposed thermal pad. It operates at up to 64MHz with the enhanced PIC18 CPU core, includes a 12-bit Analog-to-Digital Converter with Computation (ADCC), an 8-bit DAC, comparators, three 16-bit dual PWMs providing six PWM outputs, six DMA controllers, and CIP (Core Independent Peripherals) for hardware-based state machine control. The -I grade offers an industrial temperature range of -40C to +85C, while the Q43 family is AEC-Q100 Grade 1 capable for functional safety (FuSa) applications. A PIC18 microcontroller is an 8-bit Harvard-architecture MCU from Microchip's PIC18 family, sitting in the company's traditional 8-bit PIC lineup alongside PIC16 and PIC10/12/14/16 families. Within the broader MCU taxonomy, a PIC18F belongs to the 8-bit microcontroller category -> microcontroller unit (MCU) -> semiconductor device -> embedded computing. The 'F' suffix indicates Flash program memory; Q43 denotes the specific family (Core Independent Peripherals + 12-bit ADCC + 16-bit PWM); the trailing designators -I/PT specify the temperature grade and package. The PIC18F57Q43-I/PT's signature features include the 12-bit ADCC with Capacitive Voltage Divider (CVD) support for advanced touch sensing, three 16-bit dual PWMs producing six PWM outputs for motor control or lighting, six independent DMA controllers that move data between peripherals without CPU intervention, and hardware-based custom logic via the Configurable Logic Cell (CLC) and Peripheral Pin Select (PPS). This combination reduces software overhead and enables deterministic real-time control. The integrated Functional Safety (FuSa) support with dedicated safety libraries makes it suitable for safety-critical applications. Typical applications span industrial motor control (BLDC, PMSM, stepper), capacitive touch user interfaces, LED lighting drivers, automotive body and HVAC control, IoT edge nodes, and consumer appliances requiring low-power XLP (eXtreme Low Power) operation. The 128KB Flash with 8KB SRAM provides ample headroom for protocols, application logic, and bootloader, while six DMA channels prevent CPU stalls during high-throughput data movement. When designing with this MCU, allocate sufficient decoupling near VDD pins and use the PPS feature to remap peripherals to almost any I/O for optimal PCB routing. The 48-pin TQFP-EP package requires a generous ground-connected copper pad beneath the exposed pad for thermal dissipation, especially at higher clock speeds and peripheral loads. This page synthesizes distributor pricing, cross-reference alternatives, and practical design notes not typically found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F57Q43T-I/6LX

PIC18F57Q43T-I/6LX - 8-Bit 64MHz 128KB Flash MCU | Microchip

The Microchip Technology PIC18F57Q43T-I/6LX is an 8-bit PIC18 XLP microcontroller with 128 KB Flash, 8 KB SRAM, and 1 KB EEPROM, running at up to 64 MHz, housed in a 48-pin VQFN (6x6 mm) package with exposed thermal pad. It integrates a 12-bit ADC with 2 MSPS, a 12-bit DAC, three op-amps, two 8-bit DACs, six 16-bit PWMs, six DMA controllers, and full Functional Safety (FuSa) support with Class B safety library. What is an 8-bit PIC microcontroller? An 8-bit PIC microcontroller is a RISC-based embedded controller from Microchip's PIC family that processes data in 8-bit words, balancing low power, deterministic interrupt response, and rich peripheral integration. PIC microcontrollers sit within the broader microcontroller hierarchy: microcontroller -> embedded controller -> MCU -> semiconductor, and are widely deployed in consumer, industrial, and automotive subsystems where cost-effective, low-power computation is required. Key features include six DMA controllers that offload data movement between peripherals and memory without CPU intervention, three independent 16-bit dual PWMs providing six PWM outputs for motor and lighting control, vectored interrupt capability with fixed three-instruction-cycle latency, and a Core Independent Peripheral (CIP) ecosystem that lets hardware blocks run autonomously. The device operates from 1.8 V to 5.5 V across -40C to +85C industrial temperatures. The architecture combines a modified Harvard RISC core with separate program Flash and data SRAM buses, hardware multiply, and a 32-level stack. On-chip peripherals interconnect via Microchip's Peripheral Pin Select (PPS) and configurable logic cells, enabling sophisticated signal routing without external glue logic. This makes the Q43 family a strong fit for applications that previously required multiple ICs. Typical applications include functional-safety industrial control, BLDC/PMSM motor drives, IoT sensor nodes, LED lighting controllers, USB HID/CDC devices, and battery-powered portable instruments. The XLP (eXtreme Low Power) features such as nanoWatt XLP, IDLE/DOZE modes, and sleep currents below 50 nA make it well suited to energy harvesting and battery-backed designs. When designing with this device, ensure the exposed pad (EP) of the VQFN package is soldered to a sufficient copper pour for thermal dissipation and ground reference. The PPS system requires firmware configuration before the first peripheral use; reserve one GPIO for the in-circuit serial programming (ICSP) interface. This page synthesizes distributor pricing, drop-in alternative inventory, and practical design notes drawn from Microchip application notes that are not aggregated on the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F57Q84-I/PT

PIC18F57Q84-I/PT - 8-Bit MCU, 64MHz, 128KB Flash, CAN FD | Microchip

The Microchip Technology PIC18F57Q84-I/PT is an 8-bit PIC18 microcontroller running at 64 MHz with 128 KB (64K x 16) of Flash program memory, housed in a 48-pin TQFP (7x7 mm) package. It belongs to the PIC18-Q84 family, which combines Core Independent Peripherals (CIPs) with CAN FD connectivity for cost-optimized automotive and industrial applications. The integrated CIPs offload tasks such as signal conditioning, timing, and communications from the CPU, enabling deterministic real-time control with minimal firmware overhead. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory (Flash, SRAM, EEPROM), and programmable peripherals. PIC18 8-bit MCUs use Microchip's enhanced Harvard RISC architecture with 16-bit instructions and an 8-bit data path, balancing code density with deterministic interrupt response. The PIC18-Q84 sub-family specifically extends this lineage with modern interfaces (CAN FD, UART, SPI, I2C) and high-resolution CIPs suited to sensor and motor control nodes. Key specifications include 128 KB Flash, 8 KB SRAM, 1024 bytes EEPROM, 64 MHz internal oscillator, and 12-bit ADC with computation (ADCC). Communication peripherals include one CAN FD module, two UARTs, two SPIs, and two I2Cs. Core Independent Peripherals include configurable logic cells (CLC), signal measurement timer (SMT), complementary waveform generator (CWG), numerically controlled oscillator (NCO), and zero-cross detect (ZCD). A hardware crypto engine, cyclic redundancy check (CRC) module, and direct memory access (DMA) controller further reduce CPU load. The architecture uses a 16-bit instruction word with an 8-bit data bus, supports up to 16 MIPS at 64 MHz, and operates from 1.8 V to 5.5 V. The 48-pin TQFP (PT) package offers up to 44 I/O pins with high-current sink/source capability, plus peripheral pin select (PPS) for flexible signal routing. The device is qualified for industrial temperature ranges (-40 °C to +85 °C) and supports in-circuit serial programming (ICSP) and in-circuit debugging (ICD). Typical applications include CAN FD nodes in automotive body and chassis ECUs, industrial sensor hubs, BLDC motor controllers, HVAC control boards, lighting controllers, and battery management front-ends. The combination of CAN FD, 12-bit ADCC, and CWG enables sensor-driven closed-loop control with hardware-accelerated timing without burdening the CPU. When designing with this device, plan for adequate decoupling (100 nF ceramic per VDD pair), a low-ESR bulk capacitor on VDDCORE, and routing of the CAN bus with 120 Ω termination plus ESD protection. For safety-critical applications, enable the WWDT and use the CRC scanner to validate Flash contents at startup. This page synthesizes distributor pricing, drop-in family alternatives from the Site MPN list, and practical design guidance not duplicated on the manufacturer datasheet, giving procurement and design engineers a faster path from specification to qualified source.

Запрос цены Контакты

PIC18F57Q84T-I/PT

PIC18F57Q84T-I/PT - 8-bit 64MHz MCU 128KB Flash CAN-FD | Microchip

The Microchip Technology PIC18F57Q84T-I/PT is an 8-bit PIC microcontroller from the PIC18-Q84 family, featuring a 64 MHz CPU, 128 KB of Flash program memory, 13 KB of SRAM, and 1 KB of EEPROM, all housed in a 48-pin TQFP (PT) package. The device integrates Controller Area Network with Flexible Data Rate (CAN-FD), making it suitable for automotive and industrial networking applications where deterministic, high-bandwidth communication is required. The "T" suffix indicates Tape and Reel packaging, while the "I" indicates the industrial operating temperature range of -40C to +85C. A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals. The PIC18 architecture is an enhanced 8-bit Harvard RISC core that balances deterministic real-time control with low power consumption via Microchip's eXtreme Low Power (XLP) technology. The PIC18-Q84 family expands 8-bit MCUs by combining Core Independent Peripherals (CIPs) with CAN-FD, positioning the device at the intersection of cost-optimized embedded control and networked sensor/actuator nodes. Key features include a 12-bit ADC with up to 43 channels (depending on package), a 12-bit DAC, multiple DMA channels, DSM (Data Signal Modulator), complementary PWMs with edge-aligned and center-aligned modes, CIPS (Configurable Logic Cell), I2C, SPI, and two UART peripherals. These integrated peripherals offload common tasks from the CPU, reducing firmware complexity and improving deterministic response time. The PIC18F57Q84T-I/PT uses a Harvard-architecture 8-bit RISC core with a 16-bit instruction word. The high peripheral integration allows developers to implement motor control, lighting, power conversion, and sensor fusion with minimal external components. The integrated CAN-FD controller supports data rates up to 5 Mbps with payload sizes up to 64 bytes, enabling modern automotive and industrial bus communication. Typical applications include CAN-FD node endpoints in automotive body and chassis networks, BLDC motor control for fans and pumps, LED lighting controllers, HVAC sensor interfaces, and industrial automation modules. The wide operating voltage range and XLP low-power modes also support battery-powered IoT edge devices. When designing with this MCU, plan for the 48-pin TQFP footprint and provide decoupling capacitors within 5 mm of every VDD/VSS pair. Configure the CAN-FD peripheral baud rate to match the bus clock and verify timing budget using Microchip's MPLAB X IDE with the MCC code configurator. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. All data points have been cross-referenced against the official Microchip PIC18F27/47/57Q84 datasheet (DS40002213E) and current distributor listings.

Запрос цены Контакты

PIC18F6310T-I/PT

PIC18F6310T-I/PT - 8-bit PIC MCU, 8KB Flash, 64-Pin TQFP | Microchip

The Microchip Technology PIC18F6310T-I/PT is an 8-bit RISC microcontroller in the PIC18F family, featuring 8 KB of Flash program memory, 768 bytes of RAM, and 64-pin TQFP packaging. The trailing "T" suffix denotes tape-and-reel packaging, and the "I" indicates the industrial temperature range of -40C to +85C. The device operates at up to 40 MHz, delivering 10 MIPS of processing throughput for embedded control applications. An 8-bit microcontroller (MCU) is a programmable integrated circuit that combines a CPU, memory (Flash for program storage, SRAM for data), and peripheral interfaces on a single die. The PIC18F family sits within the broader PIC (Peripheral Interface Controller) architecture and traces its hierarchy to microcontroller -> embedded processor -> semiconductor device. PIC18F MCUs use a Harvard RISC architecture with separate program and data buses, and they execute most instructions in a single 4-cycle clock period (one instruction cycle per 4 oscillator cycles). Key features include 8 KB (4K x 16) of self-programmable Flash, 768 bytes of data RAM, 256 bytes of EEPROM, and a 10-bit Analog-to-Digital Converter (ADC) with up to 12 input channels. Communication peripherals include Enhanced USART, MSSP (SPI/I2C), and Parallel Slave Port. The device supports 54 digital I/O pins with high-current sink/source capability and offers multiple power-managed modes for low-power operation. The PIC18F6310 integrates advanced peripherals such as a 16-bit Capture/Compare/PWM (CCP) module, multiple timers, and a Hardware RTCC for real-time clock functions. These are designed for human-interface and control applications where deterministic real-time response is critical. The 64-pin TQFP package provides ample I/O access in a 10 x 10 mm outline suitable for moderately dense PCB designs. Typical applications include industrial manufacturing equipment, instrumentation and monitoring, data acquisition systems, power conditioning, environmental monitoring, telecom infrastructure, and consumer electronics. The wide peripheral set also makes it suitable for HVAC controls, security panels, and display drivers. When designing with this MCU, ensure VDD decoupling uses 100 nF and 10 uF capacitors placed close to the supply pins. Configure the configuration bits (fuses) for oscillator source, watchdog timer, and code protection before programming. The Industrial temperature grade allows deployment in uncontrolled thermal environments. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F6390-E/PT

PIC18F6390-E/PT - 8KB Flash LCD MCU 64TQFP | Microchip

The Microchip Technology PIC18F6390-E/PT is an 8-bit PIC18F-family flash microcontroller featuring 8 KB of program Flash, 768 bytes of RAM, an integrated LCD driver, and 68 I/O pins, all housed in a 64-pin TQFP package. It executes instructions at up to 40 MHz (10 MIPS) using Microchip's enhanced RISC architecture and supports a wide 2.0 V to 5.5 V operating voltage range suitable for battery and line-powered applications. The '-E' suffix denotes the extended industrial temperature grade of -40C to +125C. An 8-bit microcontroller is a single-chip computer built around an 8-bit data path; PIC18F devices extend this with a 16-bit instruction word, hardware multiply, and a linear program-memory map. As part of Microchip's PIC18F -> 8-bit MCU -> microcontroller -> embedded processor -> semiconductor hierarchy, this part sits in the LCD-driver segment aimed at low-power human-machine interface products such as metering and thermostat panels. Key features include nanoWatt power management with multiple idle and sleep modes, an integrated LCD driver supporting up to 192 segments, a 10-bit ADC with up to 12 channels, three timers, two capture/compare/PWM modules, two USART modules, an SPI port, and an I2C port. The 64-pin TQFP (10x10 mm) package provides ample I/O for keypad scanning and segmented LCD glass. The device architecture pairs a Harvard bus with a 32-level hardware stack and interrupt prioritization. Internal RC, crystal, and PLL clock options let designers balance throughput against EMI for cost-sensitive consumer products. The 8 KB Flash supports self-programming under firmware control, enabling field upgrades through the USART bootloader. Typical applications include handheld utility meters, thermostats and HVAC controllers, home security keypads, point-of-sale terminals, and white-goods user interfaces that need direct LCD glass drive without an external segment driver. When designing with this part, reserve 2 to 3 I/O pins for In-Circuit Serial Programming (ICSP) and place a 10 kohm pull-up on MCLR to keep the device in reset only when intended; otherwise the device can enter programming mode during brown-out events. Verify segment loading against the LCD charge-pump capacitance budget before final layout. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC18F6390-I/PT

PIC18F6390-I/PT - 8-bit 40MHz LCD MCU 8KB Flash | Microchip

The Microchip PIC18F6390-I/PT is an 8-bit CMOS RISC microcontroller from the PIC18F family, featuring an integrated LCD driver, 8KB of Flash program memory, 768 bytes of RAM, and 64-pin TQFP (10x10 mm) packaging. It executes instructions at up to 10 MIPS using a C-compiler-optimized RISC architecture clocked at 40 MHz from a 4.2 V to 5.5 V supply. This device is specifically designed for low-power human-interface applications with on-chip segmented LCD driving capability. An 8-bit microcontroller (MCU) is a single-chip computer that integrates an 8-bit CPU, program memory (Flash/ROM), data memory (RAM), peripherals, and I/O on one silicon die. PIC18F microcontrollers extend Microchip's baseline 8-bit PIC line by adding enhanced peripherals, larger memory spaces, and up to 10 MIPS throughput - making them mid-range 8-bit controllers widely deployed in consumer white goods, industrial HMIs, and metering products. The integrated LCD driver on the PIC18F6390 eliminates an external driver IC, reducing BOM cost and PCB area in segment-display applications. Key features include 8K x 16 (8KB) of self-programmable Flash, 768 bytes of RAM, 256 bytes of EEPROM, 54 I/O pins, an integrated segmented LCD controller, nanoWatt power management for ultra-low sleep currents, and a 10-bit ADC. The 64-TQFP package provides generous I/O headroom for keypad scanning, sensor input, and LCD segment multiplexing simultaneously. The CPU uses an enhanced Harvard architecture with separate program and data buses, sixteen 8-bit working registers, and a hardware multiplier that simplifies arithmetic for meter and sensor-signal processing. nanoWatt technology provides multiple power-managed modes including idle, sleep, and oscillator-switching options that drop quiescent current to microampere levels during idle periods. Typical applications include handheld meters (gas/water/electric), thermostats, home security keypads, point-of-sale terminals, medical infusion pumps, industrial process displays, and appliance user interfaces with segment LCDs. When designing with this device, allocate I/O pins for both the segment/commons of the LCD and keypad matrix. The internal LCD charge pump can supply glass bias from a single 3 V supply, but contrast is optimized when VDD is at 5 V. Use MPLAB X IDE with the XC8 compiler for firmware development. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single source for parametric, sourcing, and application information.

Запрос цены Контакты

PIC18F6390T-I/PT

PIC18F6390T-I/PT - 8KB Flash, 40MHz, LCD PIC MCU | Microchip

The Microchip Technology PIC18F6390T-I/PT is an 8-bit PIC18F microcontroller with 8KB of Flash program memory, 768 bytes of RAM, and an integrated LCD driver, housed in a 64-pin TQFP (10x10 mm) package. It operates from a 4.2V to 5.5V supply at up to 40MHz, providing 54 digital I/O pins plus dedicated LCD segment lines, making it tailored for human-machine interface (HMI) products with display requirements. What is a PIC18F microcontroller? The PIC18F family is Microchip's high-end 8-bit microcontroller line based on the PIC RISC architecture, sitting above the PIC16F and base PIC18F in the company's 8-bit portfolio. It features a 16-bit instruction word with an 8-bit data path, hardware multiplier, C-compiler friendly architecture, and rich peripheral integration (ADC, PWM, I2C, SPI, USART, USB, LCD, CTMU). PIC18F belongs to the broader 8-bit MCU hypernym chain: 8-bit microcontroller -> MCU -> embedded controller -> semiconductor IC. The 'F' suffix indicates Flash-based program memory, which supports in-system self-programming for field upgrades. Key features of the PIC18F6390 include a 10-bit ADC up to 12 channels, an integrated LCD driver capable of driving up to 192 segments, two analog comparators, one USART, one AUSART, MSSP (SPI/I2C), and nanoWatt Technology power management with multiple idle/sleep modes. The integrated Charge Time Measurement Unit (CTMU) supports capacitive touch sensing and precise time-of-flight measurements, eliminating external components for many sensing applications. The 768-byte RAM and 256-byte EEPROM complement the 8KB Flash to support data logging, metering, and user-interface state storage. Architecturally, the device uses an enhanced mid-range core with a 16-bit instruction path and 8-bit data path, a hardware 8x8 multiplier, and 31-level stack depth, enabling efficient C code generation. The part is specified for the industrial temperature range (-40C to +85C) as denoted by the 'I' designator. Typical applications include handheld metering (gas/water/electricity), thermostat and HVAC controllers, home security panels, point-of-sale terminals, white goods user interfaces, and any low-to-mid complexity product requiring a built-in segmented LCD display. When designing with the PIC18F6390T-I/PT, allocate PCB area for the LCD bias capacitors (typically 0.1uF-1uF ceramic) and follow Microchip AN649 application note for noise-tolerant LCD bias generation. Use MPLAB X IDE with MPLAB XC8 compiler for firmware development, and consider the PIC18F46K22 or PIC18F47K42 families if your design migrates to lower-power or higher-memory variants. Note: the 'T' suffix denotes Tape & Reel packaging for the original TQFP variant.

Запрос цены Контакты

PIC18F63J11-I/PT

PIC18F63J11-I/PT - 8-Bit 40MHz MCU, 8KB Flash, 64-TQFP | Microchip

The Microchip Technology PIC18F63J11-I/PT is a general-purpose 8-bit RISC PIC18J-series microcontroller (MCU) delivering 10 MIPS performance at 3V with a 40 MHz maximum clock, 8 KB (4K x 16) of self-programmable Flash program memory, 1 KB of SRAM, and 51 digital I/O pins, housed in a 64-pin TQFP (10x10 mm, 1 mm height, MS-026) package. The device is intended for cost-sensitive embedded applications such as data loggers, controllers, and consumer products that benefit from a high pin count and a generous peripheral mix. What is a PIC18J-series microcontroller? The PIC18J family is Microchip's low-voltage, nanoWatt-oriented branch of the 8-bit PIC18 architecture, integrating a Harvard RISC core with peripheral-rich analog and digital blocks, configurable I/O, and Flash program memory in a single CMOS die. Within Microchip's taxonomy, PIC18J sits below the enhanced PIC18K (XLP) and the PIC24/dsPIC 16-bit families but above the baseline PIC16 mid-range parts. Key features include a 10-bit ADC, multiple timers, enhanced CCP/ECCP, two USARTs, SPI/I2C, an 8 MHz internal oscillator (with PLL up to 40 MHz), and nanoWatt power-saving modes. The 51 I/O pins are 5V-tolerant and capable of interrupt-on-change. The Flash supports self-programming and ICD (in-circuit debug) via two dedicated pins. Architecturally, the part uses a 16-bit instruction word with an 8-bit data path, a hardware multiplier, and a vectored interrupt controller. A dedicated ICD port allows real-time debug without probe removal, and the internal oscillator with 4x PLL eliminates the external crystal in many designs, reducing BOM cost. Typical applications include industrial control panels, HVAC fan/pump controllers, USB/HID human-interface devices, sensor hubs, and low-cost data acquisition front ends. The wide 4.2-5.5V supply range suits 5V legacy system retrofits. When designing, allocate the ICD/PGD/PGC pins early since they double as digital I/O only when debugging is disabled. Place a 100 nF decoupling capacitor within 3 mm of each VDD/VSS pair, and reserve the MCLR pin with its proper 10 kohm pull-up configuration. This page consolidates distributor pricing, package-compatible drop-in alternatives from Microchip's own portfolio, application guidance, and design notes not duplicated on the manufacturer's marketing page.

Запрос цены Контакты

PIC18F63J90-I/PT

PIC18F63J90-I/PT - 8-bit 40MHz 8KB Flash LCD MCU | Microchip

The Microchip Technology PIC18F63J90-I/PT is an 8-bit PIC18 RISC microcontroller with 8KB of Flash program memory, 1024 bytes of RAM, and an integrated segmented LCD driver, housed in a 64-pin TQFP (10x10 mm) industrial-temperature package. According to Microchip datasheet DS-39791D, the device runs at up to 40 MHz from a 2.0V-3.6V supply and provides 51 digital I/O pins plus 24 LCD segment pins for a typical 128-segment display. A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (Flash/ROM), data memory (RAM), and peripheral interfaces (ADC, timers, communication controllers). The PIC18 family uses an enhanced 8-bit RISC Harvard architecture with a 16-bit instruction word, providing up to 16 MIPS performance at 40 MHz. The PIC18F63J90 belongs to the J90 sub-family, distinguished by its on-chip LCD driver, large pin count, and nanoWatt power-management features - a category within Microchip's 8-bit MCU lineup that bridges small 8-pin controllers and the 16-bit/32-bit families. Key features include a 10-bit ADC with up to 12 channels, two analog comparators, two USART modules, one SPI and one I2C peripheral, a 16-bit PWM module, and hardware multiplier for fast arithmetic. The integrated LCD driver supports 4 common and up to 48 segment lines without external charge pumps, and the nanoWatt features include idle/doze/sleep modes with typical currents below 100 nA in sleep. The architecture combines Microchip's enhanced mid-range core with a peripheral set optimized for human-machine interfaces. The on-chip LCD module drives resistive segment LCDs directly, eliminating the need for external COG or chip-on-glass drivers. Hardware peripherals such as the CCP/ECCP, MSSP (SPI/I2C), and EUSART operate autonomously from the CPU, allowing efficient handling of multiple I/O tasks. Typical applications include handheld meters, thermostats, home-security control panels, and power/gas/water utility meters - all use cases where the integrated LCD, low power, and 51 I/O pins are decisive. Industrial sensor readouts and medical dosing pumps are additional fits, benefiting from the 12-channel ADC and low-power modes. When designing with this device, allocate enough PCB area for the 64-pin TQFP footprint and ensure your programmer/debugger supports ICSP via the dedicated PGD/PGC pins. The LCD bias generation is internal but requires external capacitor network; refer to the datasheet LCD bias section for the precise component values. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

PIC18F6410-E/PT

PIC18F6410-E/PT - 8-bit MCU, 16KB Flash, 40MHz, 64-Pin TQFP

The Microchip Technology PIC18F6410-E/PT is a high-performance 8-bit RISC microcontroller with 16 KB of Flash program memory, 768 bytes of RAM, and 54 digital I/O pins, housed in a 64-pin TQFP package (10x10 mm). It operates from a 4.2V to 5.5V supply at up to 40 MHz (10 MIPS) and integrates a 10-bit ADC, nanoWatt power management, and a peripheral-rich architecture shared across the PIC18 family. An 8-bit microcontroller (MCU) is a single-chip computer built around an 8-bit data path and Harvard architecture. It executes C, assembly, or graphical code to read sensors, drive actuators, and exchange data over serial protocols. In the broader hierarchy, a microcontroller sits inside the semiconductor category, the embedded computing category, and ultimately inside the system-on-chip (SoC) parent family, alongside 16-bit, 32-bit, and 64-bit MCUs. Key features of the PIC18F6410-E/PT include 16 KB of self-programmable Flash, 768 bytes of SRAM, 256 bytes of EEPROM, 54 digital I/O, a 10-bit ADC with multiple channels, two analog comparators, two USART modules, MSSP (SPI/I2C), a 16-bit timer, three 8-bit timers, nanoWatt Technology for low-power modes, an enhanced 16-bit capture/compare/PWM module, and an ICD/ICSP debug interface. The TQFP-64 footprint exposes nearly all peripherals to external pins. Architecturally, the device uses a 16-bit instruction word with 8-bit data path and a 31-level hardware stack. nanoWatt Technology supports run, idle, and sleep modes with on-the-fly oscillator switching. The extended instruction set, hardware multiplier, and C-friendly architecture make it suitable for control loops and protocol stacks. Typical applications include industrial manufacturing equipment, instrumentation and monitoring, data acquisition, power conditioning, environmental monitoring, telecom, and consumer devices. It is also used in white goods and HVAC controllers where 8-bit MCUs with rich peripherals and 5V tolerance are preferred. When designing with this part, verify the operating temperature grade. The -E suffix denotes an extended temperature range of -40C to +125C, suitable for industrial and outdoor enclosures. Decouple VDD/VSS with 100 nF capacitors placed within 5 mm of each pin pair, and keep the ICSP clock and data traces short. This page synthesizes distributor pricing, drop-in alternatives from the PIC18F family, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

PIC18F6410T-I/PT

PIC18F6410T-I/PT - 8-bit MCU, 16KB Flash, 64-Pin TQFP | Microchip

The Microchip Technology PIC18F6410T-I/PT is an 8-bit PIC18-family RISC microcontroller with 16 KB of Flash program memory, 768 bytes of RAM, and 54 digital I/O pins, packaged in a 64-pin TQFP (PT) and supplied on tape-and-reel. It operates from 4.2 V to 5.5 V at up to 40 MHz, integrating nanoWatt power management, a 10-bit ADC, multiple timers, and standard PIC18 peripherals for embedded control designs. An 8-bit microcontroller (MCU) is a single-chip computer that combines a CPU, non-volatile program memory (Flash), volatile working memory (RAM), and on-chip peripherals such as timers, ADC, communication interfaces, and GPIO into one package. In the embedded system hierarchy, the PIC18F6410 belongs to microcontroller -> MCU -> embedded controller -> semiconductor. It is optimized for deterministic real-time control with low power consumption, serving applications where cost, footprint, and code simplicity matter more than raw throughput. Key features include the PIC18 Harvard RISC architecture with single-cycle instructions at 40 MHz (10 MIPS), 16 KB self-programmable Flash, 768 bytes of RAM, 256 bytes of EEPROM, 54 I/O, nanoWatt sleep modes, two analog comparators, a 10-bit ADC, two USARTs, MSSP (SPI/I2C), two CCP modules, and a 16-bit timer. The wide 4.2-5.5 V supply window makes it well suited to industrial 5 V rails, and the 64-pin TQFP provides ample I/O without forcing a smaller QFN footprint. Technically, the PIC18F6410 employs a 16-bit instruction word Flash with an 8-bit data path, separated program and data buses (Harvard), and a four-deep hardware stack. Interrupt handling and peripheral mapping are configured through standard PIC18 SFRs, and self-programmability under firmware control supports bootloader and field-update patterns. The device is available in both F (Flash) and LF (low-voltage Flash) variants. Typical applications include industrial control, building automation (HVAC, lighting), home appliance control panels, sensor conditioning front-ends, USB/HID bridges using external transceiver ICs, and automotive body/comfort subsystems. The 64-pin TQFP makes it a strong fit where 40-48-pin PIC18F parts lack I/O but 80-pin parts would be over-specified. Designers should plan for proper decoupling (100 nF plus bulk caps at the supply pins), in-circuit serial programming (ICSP) header access for ISP/ICD, and a quartz crystal or resonator footprint to fully utilize the 40 MHz performance. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes that are not consolidated on the manufacturer datasheet or any single distributor product page.

Запрос цены Контакты

PIC18F6490T-I/PT

PIC18F6490T-I/PT - 8-bit 40MHz 16KB Flash LCD MCU | Microchip

The Microchip Technology PIC18F6490T-I/PT is an 8-bit PIC18F microcontroller integrating 16KB of Flash program memory, 768 bytes of SRAM, and an on-chip LCD driver, housed in a 64-pin TQFP (10x10 mm) industrial-grade (-40C to +85C) package. It executes instructions at up to 40 MHz from an internal oscillator/external clock source, draws as little as nanoWatt-level sleep current, and exposes 54 digital I/O lines plus integrated peripherals such as a 10-bit ADC, multiple USART/SPI/I2C modules, timers, and capture/compare/PWM. An 8-bit microcontroller (MCU) is a microprocessor integrated with program memory (Flash/ROM), data memory (SRAM), peripherals, and I/O on a single die; it belongs to the broader microcontroller category within microcontrollers and microprocessors under semiconductor devices. PIC18F devices sit in Microchip's enhanced mid-range 8-bit family, offering a Harvard architecture, 16-bit-wide instruction word, hardware multiplier, and C-optimized instruction set that balances code density against deterministic interrupt response. The integrated segment-LCD controller makes the PIC18F6490 part of the PIC18F "LCD" subfamily specifically targeted at human-machine-interface and metering applications. Key features include 16KB (8K x 16) self-programmable Flash, 768-byte RAM, 256-byte EEPROM, an internal LCD driver with charge pump supporting up to 48 segments, nanoWatt power management with multiple idle/sleep modes, and industrial -40C to +85C temperature operation. The 64-TQFP pinout exposes full LCD segment pins while leaving ample GPIO for buttons, sensors, and communication buses. Built-in Enhanced Flash Cell technology supports >100k erase/write cycles and >40-year data retention, valuable for firmware-upgradable metering and field-deployed devices. Architecturally, the PIC18F6490 uses an 8-bit data path with 16-bit instructions and a hardware 8x8 multiplier that accelerates signed/unsigned multiply in 1 instruction cycle. The nanoWatt technology tier adds real-time clock/counter operation from a 32 kHz source while drawing microamp-level current, enabling multi-year battery life in utility metering and remote sensor applications. The LCD module includes a configurable charge pump, software-controlled contrast, and direct segment drive, removing external resistor ladders and driver ICs from segment-LCD designs. Typical applications include handheld utility meters (electric/gas/water), thermostats and HVAC controllers, home-security keypads and alarm panels, medical infusion pumps and glucose meters, point-of-sale terminals, and industrial control panels with segment-LCD readouts. The combination of on-chip LCD + nanoWatt + industrial temperature range is purpose-built for metering and panel-instrument designs where BOM cost and battery life dominate. When designing with this device, allocate sufficient PCB area for the LCD bias network and consider using the internal charge pump when the supply drops below 3V to maintain segment contrast. Always populate the decoupling capacitors specified in the manufacturer datasheet typical-application section, and follow Microchip's recommended in-circuit serial programming (ICSP) layout for production-line firmware updates.

Запрос цены Контакты

PIC18F6493-I/PT

PIC18F6493-I/PT - 8-bit 40MHz 16KB Flash LCD MCU | Microchip

The Microchip PIC18F6493-I/PT is an 8-bit PIC18 microcontroller with an integrated LCD driver and high-resolution 12-bit ADC, packaged in a 64-pin TQFP (10x10 mm). The device runs at 40 MHz, integrates 16 KB of Flash program memory (8K x 16), 768 bytes of RAM, and provides 54 digital I/O lines. It operates from a 4.2 V to 5.5 V supply and is qualified for the -40 C to +85 C industrial temperature range, as denoted by the "I" suffix. A PIC microcontroller (Programmable Integrated Circuit) is a Harvard-architecture RISC device widely used in embedded designs for deterministic control, low power consumption, and integrated peripherals. Within the broader taxonomy, the PIC18F6493 belongs to the PIC18F family of high-performance 8-bit microcontrollers, sits under the umbrella of Microchip 8-bit MCUs, and is positioned in the larger category of microcontrollers -> integrated circuits -> semiconductors. The "F" denotes Flash program memory, and the "LCD" derivative specifically integrates a segment LCD driver. Key features include a built-in LCD driver supporting up to 128 segments, a 12-bit A/D converter with up to 12 input channels, an enhanced USART, MSSP for SPI/I2C, two analog comparators, a 16-bit timer, three 8-bit timers, and nanoWatt power management. The 64-pin TQFP provides ample pin budget for simultaneous display control and analog/digital I/O. The peripheral set targets low-power human-interface products where display, sensing, and communication coexist on a single chip. Technically, the PIC18F6493 is built on an enhanced PIC18 RISC core with a hardware multiply and C-friendly architecture, allowing efficient use of MPLAB XC8 compilers. The integrated LCD driver supports static, 1/2, 1/3, and 1/4 multiplex displays with selectable charge-pump bias generation, removing the need for external bias resistors. The 12-bit ADC delivers up to 100 ksps with automatic acquisition and conversion, well-suited for precision sensor readout. These architectural choices reduce BOM cost and PCB area. Typical applications include handheld meters, thermostats, home security panels, and power/gas/water metering products. Per Microchip's product page, the device family is "easily adapted for handheld meters, thermostats, home security and power/gas/water metering products" where the integrated segment LCD, ADC, and digital I/O simplify the analog front-end and HMI circuitry. When designing with this part, choose the TQFP-64 footprint with a 1.0 mm pitch and route the LCD segment lines carefully to avoid crosstalk. Enable the on-chip LCD charge pump only when the supply voltage is below the biasing threshold to maximize contrast at low VDD. This page synthesizes distributor pricing, drop-in alternatives, application notes, and practical design considerations that go beyond what the bare Microchip datasheet offers.

Запрос цены Контакты

PIC18F64J11-I/PT

PIC18F64J11-I/PT - 8-Bit 40MHz 16KB Flash MCU | Microchip TQFP-64

The Microchip Technology PIC18F64J11-I/PT is an 8-bit PIC18 J-series microcontroller running at 40MHz (10 MIPS) with 16KB (8K x 16) of on-chip Flash program memory, housed in a 64-pin TQFP (10x10 mm) package. It integrates a 1024-byte SRAM data memory and supports 54 digital I/O lines plus a 10-bit analog-to-digital converter (ADC) for mixed-signal embedded designs. The device is rated for an industrial -40C to +85C operating range and operates from a 4.2V to 5.5V supply with on-chip 2.5V regulator support. A PIC18 microcontroller is an 8-bit Harvard-architecture MCU from Microchip's enhanced mid-range family, used in cost-sensitive embedded systems. It sits within the broader taxonomy: microcontroller (MCU) -> embedded controller -> semiconductor -> integrated circuit. The PIC18 family offers higher performance (up to 16 MIPS) than PIC16 parts and simpler programming than PIC24/dsPIC, making it a workhorse for industrial, automotive, and consumer applications. Key features of the PIC18F64J11 include nanoWatt Technology for ultra-low sleep current (sub-uA), an internal 8MHz oscillator that eliminates the need for an external crystal in many designs, 16KB of self-programmable Flash, 1KB of RAM, a 10-bit ADC, multiple timers, and Enhanced Capture/Compare/PWM modules. Communication peripherals include I2C, SPI, and Enhanced USART interfaces, and a parallel port for external memory or graphics interfacing. The PIC18F64J11 family uses a modified Harvard core with a 16-bit instruction word, single-cycle hardware multiply, and a 31-level hardware stack. The nanoWatt XLP power management offers several idle/sleep modes, internal voltage regulator, and ultra-low-power Real-Time Clock calendar operation, allowing battery-powered designs that can sleep at sub-uA currents while retaining RAM and RTCC operation. Typical applications include industrial data loggers, USB peripherals (with external transceiver), sensor signal conditioning, motor control (low-end), environmental monitoring, and cost-sensitive consumer electronics. It is also widely used in educational environments for embedded systems curriculum. When designing with this device, allocate PCB real estate for the 64-pin TQFP and provide proper decoupling: a 100nF ceramic cap within 3mm of each power pin and a bulk 10uF tantalum on VDD. For low-power designs, leverage the nanoWatt XLP sleep modes and the internal 31kHz RTCC oscillator to retain RAM while consuming <1uA.

Запрос цены Контакты

Подкатегории

Товары (35281)

PIC18F56K42-E/PT - 8-Bit 64MHz 64KB Flash MCU | Microchip

PIC18F56K42-I/MV - 64KB Flash 8-bit MCU 48-UQFN | Microchip

PIC18F56K42T-I/MV - 8-Bit 64MHz 64KB Flash XLP MCU | Microchip

PIC18F56Q43-E/6LX - 8-bit 64MHz 64KB Flash MCU | Microchip

PIC18F56Q43T-I/PT - 64KB Flash, 48-TQFP 8-bit MCU | Microchip

PIC18F57K42-E/MV - 64MHz 8-bit MCU, 128KB Flash, 48-UQFN | Microchip

PIC18F57K42-I/PT - 128KB Flash, 64MHz 8-bit MCU | Microchip

PIC18F57K42T-I/MV - 64MHz 8-Bit 128KB Flash MCU | Microchip

PIC18F57Q43-E/6LX - 128KB Flash 8-bit MCU, 64MHz, 48-VQFN | Microchip

PIC18F57Q43-I/PT - 8-Bit 64MHz 128KB Flash MCU | Microchip

PIC18F57Q43T-I/6LX - 8-Bit 64MHz 128KB Flash MCU | Microchip

PIC18F57Q84-I/PT - 8-Bit MCU, 64MHz, 128KB Flash, CAN FD | Microchip

PIC18F57Q84T-I/PT - 8-bit 64MHz MCU 128KB Flash CAN-FD | Microchip

PIC18F6310T-I/PT - 8-bit PIC MCU, 8KB Flash, 64-Pin TQFP | Microchip

PIC18F6390-E/PT - 8KB Flash LCD MCU 64TQFP | Microchip

PIC18F6390-I/PT - 8-bit 40MHz LCD MCU 8KB Flash | Microchip

PIC18F6390T-I/PT - 8KB Flash, 40MHz, LCD PIC MCU | Microchip

PIC18F63J11-I/PT - 8-Bit 40MHz MCU, 8KB Flash, 64-TQFP | Microchip

PIC18F63J90-I/PT - 8-bit 40MHz 8KB Flash LCD MCU | Microchip

PIC18F6410-E/PT - 8-bit MCU, 16KB Flash, 40MHz, 64-Pin TQFP

PIC18F6410T-I/PT - 8-bit MCU, 16KB Flash, 64-Pin TQFP | Microchip

PIC18F6490T-I/PT - 8-bit 40MHz 16KB Flash LCD MCU | Microchip

PIC18F6493-I/PT - 8-bit 40MHz 16KB Flash LCD MCU | Microchip

PIC18F64J11-I/PT - 8-Bit 40MHz 16KB Flash MCU | Microchip TQFP-64