Интегральные схемы

DSPIC33EP32MC502T-I/SS

DSPIC33EP32MC502T-I/SS - 16-bit DSC, 32KB Flash | Microchip

The Microchip DSPIC33EP32MC502T-I/SS is a 16-bit digital signal controller (DSC) with 32KB (10.7K x 24) Flash program memory, 4KB RAM, and a 60 MHz (up to 70 MIPS class) dsPIC33EP core, housed in a 28-pin SSOP surface-mount package. The T suffix denotes tape-and-reel packaging and the I suffix denotes the -40C to +85C industrial operating temperature range. A digital signal controller combines the computational core of a microcontroller with DSP-style arithmetic (multiply-accumulate, division support, DSP engine) in a single device. Within the power-management hierarchy, DSCs sit between general-purpose MCUs and dedicated DSPs, making them the de facto standard for real-time closed-loop control such as field-oriented motor control. Key features include the Motor Control PWM (MCPWM) module with complementary outputs and dead-time insertion, integrated operational amplifiers and analog comparators for current sensing, a Peripheral Trigger Generator (PTG), CAN 2.0B for industrial networking, and multiple serial interfaces for communications and debugging. These peripherals significantly reduce external component count in drive electronics. Architecturally, the dsPIC33EP core executes an optimized C compiler-friendly instruction set with hardware DSP support, allowing Field-Oriented Control (FOC) loops for BLDC and permanent-magnet synchronous motors to run with high loop rates and deterministic latency. Internal flash self-programming, watchdog timer, and brown-out reset support robust industrial designs. Typical applications include brushless DC and PMSM motor drives, power inverters and UPS systems, digital power supplies (PFC, LLC), embedded industrial networking nodes using CAN, and HVAC compressor control where energy efficiency and acoustic quietness are required. Design consideration: the dsPIC33EP core requires a VCAP/VDDCORE external stabilizing capacitor; incorrect capacitor selection or placement is the most common cause of startup failure, so follow the manufacturer datasheet layout guidance closely. This page synthesizes verified distributor data, same-package drop-in family alternatives, and practical design guidance not consolidated in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC503-H/TL

DSPIC33EP32MC503-H/TL - 16-bit DSC, 32KB Flash, Motor Control | Microchip

The Microchip Technology DSPIC33EP32MC503-H/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP32MC503 family, featuring 32KB of Flash program memory, 4KB of RAM, and a core clocked at up to 60 MHz in a 36-pin VTLA (QFN) package with exposed pad, qualified to AEC-Q100 for automotive use. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and control logic of a microcontroller. Within the power-management hierarchy, the DSC sits above generic MCUs and below dedicated DSPs: it executes fixed-point DSP instructions (multiply-accumulate, barrel shifting, modulo addressing) while simultaneously servicing real-time control loops such as field-oriented motor control and digital power conversion. Key features include an integrated 3-speed motor control PWM (MCPWM) module, quadrature encoder interface (QEI) for rotor position feedback, a CAN 2.0B controller for in-vehicle and industrial networking, three on-chip operational amplifiers, four analog comparators, four DMA channels, and five timers. The H temperature designator supports an extended -40C to +150C operating range, and the exposed-pad QFN package improves thermal dissipation in compact power electronics layouts. Architecturally, the dsPIC33EP core executes up to 60 MIPS from Flash with a pipelined Harvard architecture and DSP-enhanced instruction set. The analog front-end (3 op amps, 4 comparators, 10-bit ADC) lets designers build sensorless motor control without external signal-conditioning ICs, reducing BOM count. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, automotive actuator control, digital power supplies and solar inverters, and industrial automation nodes using CAN. Design consideration: at 60 MHz the switching-node coupling into the analog peripherals is significant - route PWM ground returns separately and use the exposed pad as a solid ground connection. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC503-I/M5

DSPIC33EP32MC503-I/M5 - 70 MIPS 16-bit DSC | Microchip Technology

The Microchip Technology DSPIC33EP32MC503-I/M5 is a 16-bit digital signal controller (DSC) delivering 70 MIPS of core performance with 32 KB (10.7K x 24) of Flash program memory and 4 KB of SRAM, housed in a 36-pin VTLA (5x5 mm) UQFN package with exposed pad. The industrial-grade -I suffix covers operation from -40C to +85C. A digital signal controller blends the deterministic interrupt behavior of a microcontroller with the multiply-accumulate hardware of a digital signal processor. In the power-management hierarchy of embedded systems, the dsPIC33E family sits above general-purpose 16-bit MCUs and below application processors, targeting real-time closed-loop control. The dsPIC33EP32MC503 is a member of the MC503 motor-control subfamily, which integrates specialized peripherals aimed at digital power conversion and precision motor drives. Key features include the 70 MIPS dsPIC DSC core with DSP engine (single-cycle MAC, dual operand fetch), a motor control PWM (MCPWM) module, on-chip operational amplifiers, analog comparators, a Peripheral Trigger Generator (PTG) for autonomous sequencing, and a CAN 2.0B controller for industrial networking. These peripherals offload timing-critical tasks from the CPU, allowing the 16-bit core to focus on control-law execution. Architecturally, the dsPIC33E core provides a wide 23-bit program address space, hardware division support, 16 x 16-bit multiply with 40-bit accumulators, and deterministic interrupt latency essential for field-oriented control (FOC) loops. The enhanced Flash architecture supports self-programming for bootloader designs, and the exposed-pad 36-VTLA (5x5) package provides low-inductance grounding for the fast switching edges of the PWM outputs. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, digital power supplies (PFC, LLC), solar inverters, and industrial automation nodes using CAN bus. The combination of MCPWM, op amps, and comparators enables sensorless trapezoidal and sinusoidal control with minimal external circuitry. When designing with this device, budget Flash carefully: 32 KB (10.7K instructions) is sufficient for FOC firmware with scalar math, but complex observers or motor identification routines may require the pin-compatible 64 KB or 128 KB variants in the same package. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC503-I/TL

DSPIC33EP32MC503-I/TL - 16-bit 70 MIPS DSC 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC503-I/TL is a 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 70 MIPS core performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 36-pin VTLA (5x5 mm) surface-mount package with exposed thermal pad. A digital signal controller combines the computational architecture of a microcontroller with the multiply-accumulate (MAC) DSP engine of a digital signal processor. In the product hierarchy, the dsPIC33EP family sits within Microchip's 16-bit MCU/DSC portfolio, below the 32-bit PIC32 line and above the 8-bit PIC families. DSCs are the natural choice for closed-loop control systems that need fast interrupt response, deterministic execution, and hardware DSP instructions in a single chip. Key features of the DSPIC33EP32MC503 include the dsPIC33E core with DSP instruction set and hardware multiplier, 32KB of self-programmable Flash and 4KB of SRAM, and the MC (Motor Control) peripheral set with high-speed PWM modules for three-phase inverter driving. The device operates from a 3.3V supply and supports industrial temperature ratings (-40C to +125C per the I suffix). In-circuit serial programming (ICSP) and in-circuit debugging are supported through the MPLAB SNAP and PICkit tools using two device I/O pins and the reset line. The MC-series peripherals target motor control directly: complementary PWM outputs with dead-time control, fast analog-to-digital conversion for current sensing, and communication interfaces (UART, SPI, I2C) for host connectivity. This makes the part well suited to field-oriented control (FOC) of BLDC and PMSM motors in appliances, power tools, pumps, and industrial drives. Typical applications include brushless DC and permanent-magnet synchronous motor control, digital power supplies and PFC stages, battery chargers, and embedded sensing and actuation nodes in industrial automation. Design consideration: the 36-VTLA exposed-pad package requires a well-designed ground via array under the exposed pad for thermal dissipation and signal integrity; power the device at a regulated 3.3V and follow Microchip's decoupling guidance (low-ESR ceramic capacitors at each supply pin). This page synthesizes distributor pricing references, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC503T-E/TL

DSPIC33EP32MC503T-E/TL - 16-bit 60 MIPs DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC503T-E/TL is a 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 60 MIPs performance, 32KB (10.7K x 24) of FLASH program memory, and 2KB of RAM, housed in a 36-pin VTLA (5x5 mm) surface-mount package with exposed pad. This automotive-qualified variant (AEC-Q100, -40C to +125C extended temperature) operates from a single 3.3V supply and integrates CAN, I2C, SPI, UART/USART, IrDA, LINbus, and QEI connectivity, making it a complete single-chip motor-control solution. A digital signal controller combines the computational throughput of a DSP with the deterministic control peripherals and interrupt architecture of a microcontroller. Within the power-management hierarchy, the dsPIC33EP family sits between general-purpose MCUs and dedicated motor-control ASICs, offering a Harvard-architecture dsPIC RISC core, hardware DSP multiply-accumulate units, and precision analog peripherals in one package. Key features include the 16-bit dsPIC core executing up to 60 MIPs (the family is specified up to 70 MIPS on faster speed grades), dual-SHA motor-control PWM modules suited to BLDC/PMSM/ACIM drives, 12-bit ADC with multiple sample-and-hold circuits for simultaneous multi-channel sampling, and an integrated CAN 2.0B controller for automotive and industrial networks. Core-independent peripherals offload timing-critical tasks from software, improving deterministic behavior in closed-loop current control. The DSP engine supports single-cycle MAC and dual operand fetch, enabling fast execution of FOC (Field Oriented Control) algorithms, Clarke/Park transforms, and PID loops. On-chip features such as watchdog, brown-out reset, power-on reset, and clock fault protection improve system safety in automotive environments. Typical applications include brushless DC and permanent-magnet motor drives, automotive auxiliary motor control, electric power steering support systems, industrial automation actuators, power-factor-correction converters, and digitally controlled power supplies where CAN connectivity and precise PWM are required. Design consideration: keep the exposed thermal pad soldered to a ground plane for thermal and EMC performance, and use Microchip's Motor Control GUI/MPLAB X toolchain for firmware development and tuning. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

DSPIC33EP32MC503T-I/TL

DSPIC33EP32MC503T-I/TL - 70 MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33EP32MC503T-I/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP32MC50x motor-control family, delivering 70 MIPS performance, 32KB (10.7K x 24) of Flash program memory, and 4KB of RAM in a 36-pin VTLA (5x5 mm) QFN package. The -I suffix indicates an industrial operating temperature range of -40C to +85C, and the T prefix denotes tape-and-reel delivery for automated assembly. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and ease of use of a microcontroller. In the embedded hierarchy, the dsPIC33E family sits between general-purpose 16-bit MCUs and standalone DSPs, making it a common choice in the microcontroller and digital signal processor (DSC) segment for real-time closed-loop control. Key features include a 70 MIPS dsPIC DSC core with DSP engine (17-bit x 17-bit single-cycle multiply, 32/16-bit divide, dual 40-bit accumulators), dedicated Motor Control PWM (MCPWM) peripherals, on-chip operational amplifiers, comparators, and a Peripheral Trigger Generator (PTG) as confirmed by RS Components and DigiKey listings. These analog and PWM blocks directly serve field-oriented control (FOC) of PMSM and BLDC motors. Architecturally, the dsPIC33EP core executes most instructions in a single cycle at up to 70 MIPS, with hardware DSP multiply-accumulate supporting current-loop bandwidths needed by servo, industrial, and consumer motor drives. The integrated op amps allow in-line current-shunt amplification without external amplifiers, reducing bill-of-material cost. Typical applications include BLDC and PMSM motor control, power conversion (digital power supplies, PFC), industrial automation nodes, and embedded control in HVAC and appliance systems. Design consideration: the 36-pin VTLA QFN requires an exposed thermal pad soldered to a grounded copper pour for both thermal and electrical performance; follow Microchip layout guidance for QFN footprints. This page synthesizes distributor availability data, same-family drop-in alternatives, and practical design notes not consolidated in the manufacturer datasheet. Pricing shown is an estimate as of 2026-09-25; request a quote for current pricing.

Запрос цены Контакты

DSPIC33EP32MC504-E/MV

DSPIC33EP32MC504-E/MV - 60 MIPS Motor Control DSC | Microchip

The Microchip Technology DSPIC33EP32MC504-E/MV is a 16-bit dsPIC33EP digital signal controller (DSC) delivering 60 MIPS core performance, 32 KB of Flash program memory and 4 KB of RAM, housed in a 48-pin UQFN (6x6 mm) package with exposed pad and AEC-Q100 automotive qualification. A digital signal controller combines the computational throughput of a DSP with the integrated peripherals and deterministic behavior of a microcontroller. Within the power-management hierarchy, the DSC sits above a general-purpose MCU in the microcontroller and digital signal processor family, and the dsPIC33EP series targets closed-loop control systems that need hardware math acceleration, fast PWM and rich analog integration in a single chip. Key features include the high-speed Motor Control PWM (MCPWM) peripheral with complementary outputs and dead-time control, an integrated CAN 2.0B module, internal op amps and analog comparators, a Reconfigurable Peripheral Group (PTG), and 4 DMA channels with 5 16-bit timers. These peripherals allow current loops, commutation logic and field-oriented control to be implemented largely in hardware with minimal CPU overhead. The dsPIC33EP core uses an enhanced 16-bit architecture with DSP multiply-accumulate instructions, dual operand fetch and single-cycle MAC, plus hardware divide support. The -E temperature option guarantees operation from -40C to +125C, and the exposed-pad UQFN-48 package provides low-inductance power delivery for fast PWM switching edges. Typical applications include brushless DC and PMSM motor control, digital power supplies (LLC, totem-pole PFC), automotive auxiliary systems, and industrial drives. The CAN interface makes the part a natural fit for vehicle networks and factory fieldbus nodes. When designing, budget the Flash carefully: 32 KB (10.7K x 24-bit instructions) is ample for FOC firmware but leaves limited headroom for bootloaders plus fieldbus stacks. This page synthesizes distributor pricing, drop-in same-family alternatives, pinout guidance and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC504-E/TL

DSPIC33EP32MC504-E/TL - 60 MIPS 16-bit DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504-E/TL is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering 60 MIPS performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 44-pin VTLA (6x6 mm QFN with exposed pad) package. A digital signal controller combines the computational architecture of a microcontroller with DSP-engine features such as single-cycle multiply-accumulate, hardware divide, and DSP instruction support. Within the power-management hierarchy, DSCs occupy the tier above general-purpose MCUs for embedded control, sitting closest to dedicated motor-control ASICs while retaining full software flexibility. The dsPIC33EP family is Microchip's 16-bit flash-based DSC generation for precision embedded control. Key features include a 16-bit dsPIC core running at up to 60 MIPS from a 3.3V supply, 35 general-purpose I/O lines, integrated PWM channels for motor and power conversion control, an analog-to-digital converter, DMA channels for data movement without CPU intervention, and multiple pairs of PGECx/PGEDx pins for in-circuit serial programming (ICSP). The E suffix denotes the automotive temperature grade of -40C to +125C. Technically, the dsPIC33EP core achieves near-single-cycle instruction throughput with a pipelined architecture, and the high-speed PWM module supports complementary outputs, dead-time insertion, and fault protection - the essential building blocks for field-oriented control (FOC) of PMSM/BLDC motors and digital power supplies. The 6x6 mm QFN exposed-pad package provides low-inductance ground return for switching-adjacent analog operation. Typical applications include brushless DC and permanent-magnet motor drives, digital power supplies (PFC, LLC), UPS systems, automotive auxiliary motor control, and industrial sensing front-ends. The AEC-Q100 qualification makes it suitable for under-hood and automotive body applications. Design consideration: use one matched PGECx/PGEDx pair for ICSP (e.g., PGEC2 with PGED2) and connect all VDD/VSS pins; decouple each supply pin with 100 nF ceramics. This page synthesizes distributor pricing tiers, drop-in family alternatives, and design notes not consolidated in the manufacturer datasheet. Pricing as of 2026-09-25.

Запрос цены Контакты

DSPIC33EP32MC504-H/ML

DSPIC33EP32MC504-H/ML - 16-bit 70 MIPS DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504-H/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering up to 70 MIPS core performance with 32KB of Flash program memory and 4KB of RAM, housed in a 44-pin VQFN package with exposed pad and qualified for AEC-Q100 automotive applications. A digital signal controller combines the computational architecture of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy of embedded systems, the DSC sits above general-purpose MCUs for control-loop tasks: the dsPIC33E core executes DSP multiply-accumulate instructions, making the family a standard choice for field-oriented motor control, digital power conversion, and sensor-fusion workloads that a conventional 8-bit MCU cannot close at the required loop bandwidth. Key features include the 70 MIPS dsPIC DSC core, integrated high-speed PWM modules suited to motor-control and power-supply topologies, and on-chip op amps with advanced analog peripherals as highlighted in the dsPIC33EP32MC504 product description. The device runs from a 3.3V supply, matching modern logic rails and battery-backed systems. Technically, the dsPIC33EP32MC504 is one of the dsPIC33EPXXXMC20X/50X family devices described in the Microchip family data sheet (DS70000657J). The ADC can be configured as 10-bit, 1.1 Msps with four sample-and-hold circuits or 12-bit, 500 ksps with one sample-and-hold, with flexible and independent ADC trigger sources, and up to three op amp/comparator blocks with direct ADC connection. Debugging is supported through multiple PGECx/PGEDx ICSP channel pairs. Typical applications include brushless DC and PMSM motor control, digital power supplies such as PFC and LLC stages, automotive body and powertrain auxiliaries, and industrial inverters - all cases where high-resolution PWM, fast ADC triggering, and deterministic DSP math must coexist on one chip. A key design consideration: the H temperature suffix supports extended ambient conditions, but the exposed-pad VQFN must be soldered to a well-coppered ground plane for thermal and ground integrity, and ICSP pairs (PGECx/PGEDx) must be routed as matched pairs per the programming guide. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC504-H/PT

DSPIC33EP32MC504-H/PT - 16-bit 60MIPS DSC 32KB Flash TQFP-44 | Microchip

The Microchip Technology DSPIC33EP32MC504-H/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family delivering up to 60 MIPS performance, with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 44-pin TQFP (10x10 mm) surface-mount package. This automotive-grade, AEC-Q100 qualified device integrates high-speed motor-control PWM, a quadrature encoder interface (QEI), CAN, three on-chip operational amplifiers and four comparators. A digital signal controller combines the computational power of a digital signal processor with the peripheral set and ease of use of a microcontroller. Within the power-management hierarchy, the DSC sits above a general-purpose MCU: its DSP engine (single-cycle MAC, barrel shifter, dual operand fetch) and dedicated motor-control peripherals make it a specialized member of the broader 16-bit microcontroller family targeted at real-time control loops. Key differentiating specifications include the 60 MIPS dsPIC33E core with DSP instruction extensions, 32KB self-programming Flash with ECC, 4 DMA channels, 5 timers, and an analog front end of 3 op amps and 4 comparators that offloads external signal-conditioning components. The integrated MCPWM module supports complementary and center-aligned PWM outputs with dead-time control, essential for inverter and motor-drive topologies, while the QEI module interfaces directly with rotary encoders. Architecturally, the device is built on CMOS process technology with a modified Harvard bus, supporting up to 85 general-purpose I/O on larger packages (35 usable on the 44-pin TQFP), multiple interrupt vectors, boundary-scan support, and In-Circuit Serial Programming (ICSP) via any PGECx/PGEDx pair. The -H suffix denotes the high-temperature automotive operating range. Typical applications include brushless DC and PMSM motor drives, power-factor-correction converters, digital UPS systems, automotive electric pumps and actuators, and industrial motion-control boards where CAN connectivity and encoder feedback are required. Design consideration: the device operates from a 3V to 3.6V supply; all VDD/VSS pairs must be decoupled with 100nF ceramics placed close to the pins, and MCLR must be pulled up for reliable ICSP debugging. This page synthesizes distributor pricing, drop-in family alternatives, application guidance and design notes not consolidated in the manufacturer datasheet, as of 2026-09-25.

Запрос цены Контакты

DSPIC33EP32MC504-H/TL

DSPIC33EP32MC504-H/TL - 70MIPS 16-bit Motor Control DSC | Microchip

The Microchip Technology DSPIC33EP32MC504-H/TL is a 16-bit dsPIC33EP digital signal controller (DSC) with a 70 MIPS dsPIC core, 32KB flash program memory, 4KB RAM, and a 3.3V supply, housed in a 44-pin VTLA (TQFP-style, 6x6 mm) surface-mount package and qualified to AEC-Q100 for automotive applications. A digital signal controller combines the compute architecture of a microcontroller with the math acceleration of a DSP. In the power-management hierarchy, a DSC sits above a general-purpose MCU for real-time, computation-intensive tasks such as field-oriented control (FOC) of three-phase motors, where a single control loop must execute a full control algorithm within tens of microseconds. Microchip's dsPIC33E family merges a 16-bit RISC pipeline with DSP multiply-accumulate instructions and dedicated motor-control peripherals on one silicon die. Key differentiating features of this part include three on-chip operational amplifiers and four analog comparators, which offload signal-conditioning stages that would otherwise require external op-amp ICs in inverter current-sense circuits. A motor-control PWM (MCPWM) module with complementary outputs, dead-time insertion and fault inputs drives three-phase bridges directly, while a quadrature encoder interface (QEI) provides position feedback from rotary encoders. An ECAN (CAN 2.0B) module integrates the controller into automotive and industrial networks at up to 1 Mbit/s. Technically, the dsPIC33EP core runs at up to 70 MIPS (60 MHz instruction frequency variant cited by distributors) with single-cycle MAC, dual operands and hardware division support, allowing sensorless or sensored FOC to be executed in C or assembly with headroom. Flash is readable during erase/write, and self-programming supports field firmware updates. Typical applications include BLDC and PMSM motor drives, power inverters and solar micro-inverters, digital power supplies (PFC, LLC), and electric-power-steering or HVAC-blower systems where AEC-Q100 qualification is mandatory. Design consideration: budget the PLL configuration carefully - the -H suffix denotes an extended temperature variant, and 3.3V rails must be decoupled at every VDD pin for clean ADC sampling. This page adds distributor cross-reference data, same-family drop-in alternatives, and design guidance not consolidated in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC504-I/ML

DSPIC33EP32MC504-I/ML - 70 MIPS 16-bit DSC, QFN-44 | Microchip

The Microchip Technology DSPIC33EP32MC504-I/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP motor-control family, delivering up to 70 MIPS core performance at 60 MHz, with 32 KB of Flash program memory, 4 KB of RAM, and 44 pins in a QFN-44 (ML) surface-mount package. A digital signal controller combines the compute architecture of a microcontroller with DSP capability: a 16-bit modified Harvard core, hardware multiply-accumulate (MAC), barrel shifter, and single-cycle division support. DSCs sit between general-purpose MCUs and dedicated DSPs in the signal-processing hierarchy, making them the preferred choice for closed-loop real-time control such as field-oriented motor control and digital power conversion. Key features of this part include an integrated MCPWM motor-control PWM module with complementary outputs and dead-time control, three on-chip operational amplifiers, four analog comparators, a 10-bit ADC, quadrature encoder interface (QEI), one CAN module for industrial networking, and four DMA channels that offload data movement from the CPU. Architecturally, the dsPIC33EP core uses an enhanced pipelined C compiler-friendly instruction set with DSP multiply-accumulate instructions, supporting fast execution of PI and Park/Clarke transform loops. The on-chip op amps can be configured as current-sense amplifiers feeding the ADC, reducing external component count in inverter designs. Typical applications include brushless DC (BLDC) and permanent-magnet synchronous motor (PMSM) drives, digital SMPS and power-factor-correction converters, and industrial automation nodes using CAN. The QEI input directly interfaces rotary encoders for servo positioning. When designing with this device, use any matched PGECx/PGEDx pair consistently for ICSP programming, connect all VDD/VSS pins, and budget Flash carefully since the 32 KB program memory can be limiting with complex field-oriented control plus communication stacks. This page synthesizes distributor data, same-family drop-in alternatives, and practical design guidance not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP32MC504-I/MV

DSPIC33EP32MC504-I/MV - 16-Bit 70 MIPS DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504-I/MV is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 48-pin UQFN (6x6 mm) surface-mount package. A digital signal controller combines the computational strengths of a microcontroller with the DSP capabilities of a digital signal processor in a single core. Within the power management hierarchy, the DSC sits between a general-purpose MCU and a dedicated DSP: it runs deterministic C code like an MCU but adds DSP engine instructions, a barrel shifter, and hardware multiply-accumulate that accelerate control-loop mathematics. This makes the dsPIC33E family a mainstay for digital power conversion, motor field-oriented control (FOC), and embedded sensing applications. Key features include the 70 MIPS dsPIC33E core with integrated DSP engine, a Motor Control PWM (MCPWM) peripheral for precision three-phase drive, CAN 2.0B connectivity alongside I2C, SPI, UART/USART, IrDA, LINbus, and QEI interfaces, plus 4 DMA channels that offload data movement from the CPU. The device also provides 35 general-purpose I/O pins and 5 timers. Technical depth: the dsPIC33EP core executes most instructions in a single cycle at up to 70 MIPS, with hardware DSP multiply, divide support, and two address generation units. Peripherals include brown-out detect/reset, power-on reset, watchdog timer, and motor-control-specific PWM modules designed for complementary outputs with dead-time insertion - essential for driving half-bridges safely in inverter and BLDC/PMSM designs. Typical applications include brushless DC and permanent-magnet synchronous motor control, digital power supplies (LLC, PFC, buck/boost), and industrial automation nodes using the CAN bus. The integrated MCPWM and QEI peripherals directly serve these use cases without external logic. Design consideration: allocate adequate decoupling on all VDD pins and place the VCAP stabilizing capacitor exactly as specified in the family datasheet (DS70000657J); VCAP is required for core-voltage regulation and must not be omitted or undersized. This page synthesizes distributor pricing, drop-in alternatives, pinout guidance, and practical design notes not found in the manufacturer datasheet alone.

Запрос цены Контакты

DSPIC33EP32MC504T-E/ML

DSPIC33EP32MC504T-E/ML - 60MIPS 16-bit DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504T-E/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering 60 MIPs performance with 32KB (10.7K x 24) of FLASH program memory, integrated DSP engine, and a 44-pin QFN (8x8 mm) exposed-pad package. It is AEC-Q100 qualified for automotive applications and rated for extended temperature operation from -40C to +125C. A digital signal controller combines the compute throughput of a DSP with the peripheral integration and deterministic control flow of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes single-cycle MAC and DSP instructions for control-loop math while also handling general I/O, communication, and analog tasks on one chip. This makes the dsPIC33E family a standard choice for embedded motor control and digital power conversion. Key features include the 16-bit dsPIC33E core with DSP instruction extensions, high-speed PWM peripherals for motor control, advanced analog integration, 3.3V operation, and surface-mount packaging with an exposed pad for thermal and ground performance. The T suffix indicates Tape and Reel delivery for automated assembly, and the E suffix denotes the extended -40C to +125C operating range with AEC-Q100 qualification. Architecturally, the device uses a modified Harvard pipeline that fetches 24-bit instructions from FLASH organized as 10.7K x 24 words, with dedicated hardware addressing modes (modulo and bit-reversed) that accelerate FIR filters, PID loops, and coordinate transforms common in field-oriented motor control. Typical applications include precision BLDC and PMSM motor control, digital power supplies (PFC, LLC), automotive auxiliary control modules, and industrial drives where a single-chip solution must close fast current loops at 60 MIPs. Design consideration: budget PCB copper under the exposed pad for heat spreading and verify that your programmer/debugger (e.g., ICSP tooling) supports the dsPIC33EP family before layout freeze. This page synthesizes distributor pricing, drop-in alternatives, comparison tables, and practical design notes not found in the manufacturer datasheet, giving engineers a single decision-ready resource. Pricing shown is as of 2026-09-25.

Запрос цены Контакты

DSPIC33EP32MC504T-E/PT

DSPIC33EP32MC504T-E/PT - 16-bit 60 MIPS DSC, 44-TQFP | Microchip

The Microchip Technology DSPIC33EP32MC504T-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 60 MIPS performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 44-pin TQFP (10x10 mm) package. The device is AEC-Q100 qualified for automotive applications and operates over an extended -40C to +125C temperature range. A digital signal controller combines the computational throughput of a DSP with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, a DSC sits between a general-purpose MCU and a dedicated DSP: it executes DSP-class multiply-accumulate instructions while offering motor-control PWM, quadrature encoder interface, CAN and analog peripherals on-chip, making it the standard choice for embedded control systems. Key features include the MCPWM (motor control PWM) module for advanced motor drive topologies, a QEI (quadrature encoder interface) for position feedback, a CAN module for robust in-vehicle and industrial networking, three on-chip op-amps and four comparators that reduce external analog component count, and up to 35 general-purpose I/O. The core runs at up to 60 MIPS (60 MHz) from a 3.0V to 3.6V single supply. Architecturally, the dsPIC33EP core uses a modified Harvard pipeline with DSP multiply-accumulate, 40-bit wide accumulators, and dual operand fetch, enabling single-cycle MAC operations. Programming in C with Microchip MPLAB X and the XC16 compiler, plus dsPIC DSC Peripheral Libraries, shortens development cycles for field-oriented motor control. Typical applications include BLDC and PMSM motor control, automotive auxiliary systems, digital power supplies, and industrial drives. The integrated MCPWM with complementary outputs and dead-time insertion maps directly onto three-phase inverter designs, while the QEI closes the speed/position loop without a second chip. Design consideration: keep the supply within 3.0V-3.6V and place 0.1uF decoupling at each VDD pin; the extended-temperature -E grade requires derating analysis near +125C for flash endurance. This page adds value beyond the datasheet by synthesizing drop-in family alternatives, application pairings, and sourcing information in one structured reference.

Запрос цены Контакты

DSPIC33EP32MC504T-E/TL

DSPIC33EP32MC504T-E/TL - 60 MIPs 16-bit DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504T-E/TL is an automotive-grade 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 60 MIPs performance, with 32KB (10.7K x 24) of FLASH program memory and 2KB of RAM, housed in a 44-pin VTLA (6x6 mm) surface-mount package with exposed pad. A digital signal controller combines the compute architecture of a microcontroller with the mathematical throughput of a DSP. Within the power management hierarchy of embedded systems, a DSC sits above a general-purpose MCU for control-loop-intensive tasks: it executes single-cycle multiply-accumulate (MAC) instructions and DSP-style addressing modes, making it the natural choice for motor control, digital power conversion, and sensor signal processing where a standard 8-bit or basic 16-bit MCU struggles to close control loops fast enough. Key features of this device include the 16-bit dsPIC33EP core clocked for 60 MIPS execution, 32KB of self-programmable FLASH organized as 10.7K x 24-bit instruction words, 2KB of on-chip SRAM, and an extended temperature range (-40C to +125C) indicated by the E temperature suffix. The T in the ordering code denotes tape-and-reel packaging for automated assembly. AEC-Q100 qualification makes this device suitable for automotive applications where consumer-grade parts are not acceptable. The dsPIC33EP family integrates enhanced on-chip peripherals for precision motor control systems, including high-speed PWM, analog-to-digital conversion, and communication interfaces, per Microchip's family overview. The 3.3V supply domain keeps interfacing simple with modern logic and sensor ICs. Typical applications include BLDC and PMSM motor control drives, automotive auxiliary systems, digital power supplies (PFC, LLC controllers), industrial automation nodes, and embedded control in harsh thermal environments where the extended -40C to +125C rating is required. A key design consideration is memory headroom: 32KB FLASH and 2KB RAM are ample for single-loop control firmware, but complex multi-axis systems or protocol stacks may need the 256KB variants in the same family footprint. This page synthesizes verified distributor data, drop-in family alternatives, and practical design notes in one place - information engineers otherwise have to assemble manually from multiple datasheet and distributor sources.

Запрос цены Контакты

DSPIC33EP32MC504T-I/MV

DSPIC33EP32MC504T-I/MV - 16-bit 70 MIPS DSC, 32KB Flash | Microchip

The Microchip Technology DSPIC33EP32MC504T-I/MV is a 16-bit digital signal controller (DSC) from the dsPIC33EP32MC504 family, delivering up to 70 MIPS performance with 32KB (10.7K x 24) of Flash program memory and 4KB of RAM, housed in a 48-pin UQFN (6x6 mm) package with exposed pad. A digital signal controller combines the computing architecture of a microcontroller with the mathematical throughput of a digital signal processor. Within the power-management hierarchy of embedded silicon, the DSC sits between a general-purpose MCU and a dedicated DSP: it retains deterministic, interrupt-driven control flow and rich on-chip peripherals while adding a DSP engine for fast multiply-accumulate operations used in filters, transforms, and control loops such as field-oriented control (FOC) of motors. Key features include the 70 MIPS dsPIC33E CPU core, Motor Control PWM (MCPWM) modules with complementary outputs and dead-time insertion, a CAN 2.0B controller for industrial networking, 4 direct memory access (DMA) channels, and 5 general-purpose timers. These peripherals let a single chip close high-speed current loops and handle communications without external logic. Technically, the dsPIC33E core operates from a 3V to 3.6V single supply (per distributor electrical data, 60 MHz maximum clock figure, 70 MIPS instruction throughput) and integrates the DSP engine, watchdog, and low-jitter PLL clocking. The industrial temperature grade (-40C to +85C) and compact 6x6 mm UQFN footprint support dense power-electronics layouts where thermal performance of the exposed pad aids heat dissipation. Typical applications include precision motor control (BLDC, PMSM, ACIM), digital power supplies and LED drivers, sensorless FOC inverters, and industrial automation nodes requiring CAN connectivity. The MCPWM plus 12-bit ADC pipeline is specifically optimized for control loops in the 10-100 kHz range. Design consideration: the 3.0-3.6V supply window requires a clean LDO or buck-derived 3.3V rail; ensure the exposed thermal pad is soldered to a ground pour for both electrical return and heat removal, and observe the maximum clock frequency figures in the manufacturer datasheet when configuring the PLL. This page synthesizes distributor pricing context, drop-in same-package alternatives, and practical design notes not found in the manufacturer datasheet, providing one consolidated engineering reference for the DSPIC33EP32MC504T-I/MV.

Запрос цены Контакты

DSPIC33EP32MC504T-I/TL

DSPIC33EP32MC504T-I/TL - 16-bit DSC 32KB Flash 60MHz | Microchip

The Microchip Technology DSPIC33EP32MC504T-I/TL is a 16-bit dsPIC33EP digital signal controller (DSC) with 32KB Flash program memory, 4KB RAM, and operation up to 60 MHz, housed in a 44-pin VTLA (6x6 mm) surface-mount package with exposed pad. A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and deterministic control of a microcontroller. Within the power-management hierarchy, the DSC sits above general-purpose MCUs and below dedicated DSPs, making the dsPIC33 family a category leader for embedded motor control, digital power conversion, and sensing systems that need math acceleration without a separate DSP chip. Key features of this device include the dsPIC33E core with DSP engine (17-bit x 17-bit single-cycle multiplier, 32-bit accumulator, divide support), motor-control PWM (MCPWM) with complementary outputs and dead-time insertion, quadrature encoder interface (QEI), and a CAN 2.0B module for industrial networking. Analog integration is a headline differentiator: three on-chip operational amplifiers and four analog comparators reduce external component count in current-sense and feedback loops, alongside a 10-bit ADC and 35 general-purpose I/O pins. Architecturally, the dsPIC33EP family uses an enhanced Harvard pipeline executing from 10.7K x 24-bit instruction-word Flash, with 4 DMA channels and 5 timers to offload the CPU. The device operates from a single 3.0V to 3.6V supply, and the I temperature grade covers -40C to +85C ambient. The /TL ordering code denotes Tape & Reel packaging of the 44-VTLA 6x6 mm exposed-pad option, which provides low inductance and good thermal performance in a compact footprint. Typical applications include brushless DC and PMSM motor drives (sensorless and encoder-based), digital power supplies and solar inverters, and embedded control in robotics, instrumentation, and consumer appliances where the CAN bus, MCPWM, and integrated analog simplify the bill of materials. A key design consideration: dsPIC33EP parts require a stable 3.3V rail and careful VDD/VSS decoupling on the exposed pad; also budget Flash carefully, as 32KB fills quickly with motor-control firmware plus CAN stacks. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP512GM304-E/ML

DSPIC33EP512GM304-E/ML - 16-bit DSC 512KB Flash 60 MIPS | Microchip

The Microchip Technology DSPIC33EP512GM304-E/ML is a 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 60 MIPS performance with 512KB (170K x 24) of FLASH program memory and an automotive-grade AEC-Q100 qualified extended-temperature build in a 44-pin QFN (8x8 mm) exposed-pad package. A digital signal controller combines the computational architecture of a microcontroller with the numeric acceleration of a DSP. In the semiconductor hierarchy, the dsPIC33EP sits within Microchip's 16-bit MCU portfolio: DSC -> 16-bit microcontroller -> embedded processor -> semiconductor IC. Its Harvard architecture with a pipelined DSP engine makes it a natural fit where both general-purpose control and real-time signal processing are required, such as digital power conversion and field-oriented motor control. Key features include the 16-bit dsPIC33E CPU core running at up to 60 MIPS (the family core supports up to 70 MIPS), 512KB of self-programmable FLASH, 12 channels of motor-control PWM (12 MC PWM), 8 input capture and 8 output compare channels, 2 quadrature encoder interfaces (QEI), integrated operational amplifiers, and communication peripherals including I2C, IrDA, LINbus, SPI, UART/USART, plus watchdog timer (WDT) and power-on reset (POR). The -E/ML suffix denotes the extended -40C to +125C operating range and AEC-Q100 automotive qualification on a 3.3V supply. Internally, the DSP engine provides single-cycle MAC and 40-bit accumulators, enabling efficient execution of control loops and filter algorithms, while the integrated op-amps reduce external analog component count in current-sense front ends. Typical applications include precision BLDC/PMSM motor control, digital power supplies (PFC, LLC), automotive auxiliary systems, and industrial drives. The 12-channel motor-control PWM and dual QEI directly target servo and traction applications. Design consideration: plan your clock configuration carefully - maximum MIPS is achieved with the internal PLL from the primary oscillator; also budget the QFN exposed pad as the primary ground and thermal path in your PCB layout. This page synthesizes distributor pricing (LCSC from $7.1201, in stock as of 2026-09-25), same-package drop-in alternatives, and practical design notes beyond what the manufacturer datasheet provides.

Запрос цены Контакты

DSPIC33EP512GM304-E/PT

DSPIC33EP512GM304-E/PT - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512GM304-E/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 512 KB (170K x 24) of Flash program memory, 48 KB of RAM, and 35 general-purpose I/O pins in a 44-pin TQFP package with 0.8 mm terminal pitch. A digital signal controller combines the computational throughput of a digital signal processor with the peripheral integration and ease of use of a microcontroller. Within the power-management hierarchy, a DSC such as the dsPIC33EP sits above general-purpose MCUs in signal-processing capability, making the dsPIC33E family a common choice wherever real-time control loops must execute DSP-class mathematics, such as fast Fourier transforms, PID control, or field-oriented motor control, at kilohertz loop rates. Key features of the DSPIC33EP512GM304-E/PT include a dsPIC DSC core operating at 70 MIPS, 12 motor-control PWM (MCPWM) channels, 8 input capture and 8 output compare peripherals, and 2 quadrature encoder interfaces (QEI) for closed-loop motor positioning. Integrated analog includes 4 on-chip operational amplifiers and a Charge Time Measurement Unit (CTMU) for capacitive touch and precise timing measurements. Technical depth: the device is fabricated in CMOS technology and runs from a single 3.3 V supply. A Peripheral Trigger Generator (PTG) automates peripheral sequencing to offload the CPU, while 4 DMA channels move data without CPU intervention and 5 external interrupt sources support fast event response. The Harvard-architecture 16-bit core with DSP engine provides single-cycle MAC and 40-bit accumulators for high-throughput filtering. Typical applications include precision brushless DC and PMSM motor control, digital power supplies (switching converters and inverters), and industrial automation sensors and actuators. The four on-chip op-amps reduce external component count in current-sense front ends. Design consideration: the /PT suffix denotes the 44-pin TQFP tray package and the -E temperature grade supports -40C to +125C operation; ensure the PCB copper area accounts for full-load power dissipation at elevated ambient temperatures. This page synthesizes distributor pricing, drop-in same-family alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP512GM304-H/PT

DSPIC33EP512GM304-H/PT - 70 MIPS 16-Bit DSC 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512GM304-H/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP family, delivering up to 70 MIPS performance with 512 KB (170K x 24) of Flash program memory and 16 KB of RAM in a 44-pin TQFP (10x10 mm) surface-mount package, qualified to AEC-Q100 for automotive applications. A digital signal controller combines the computational architecture of a microcontroller with the numeric acceleration of a digital signal processor. Within the power-management hierarchy of embedded systems, the DSC sits between general-purpose MCUs and dedicated DSPs, making the dsPIC33E family a staple in digital power conversion, motor control, and precision sensing where tight control loops must execute fast multiply-accumulate operations on real-time feedback signals. Key features of this part include the 70 MIPS dsPIC33E core with integrated DSP engine, 512 KB of self-programmable Flash yielding 170K x 24-bit instruction words, 16 KB of RAM, and rich on-chip analog and timing peripherals. Per distributor specifications (Mouser), the device integrates 8 input capture / 8 output compare channels, 2 quadrature encoder interfaces (QEI), 4 on-chip operational amplifiers, and 12 motor-control PWM channels - a combination purpose-built for sensorless and sensored motor control without external analog front-end components. Architecturally, the Harvard-architecture dsPIC core executes most instructions in a single cycle at 3.3 V operation. The integrated op-amps can be routed internally to analog comparators and ADC inputs, reducing bill-of-material cost and board area in current-sensing and signal-conditioning paths. The 12-channel motor-control PWM module supports complementary outputs with dead-time insertion for three-phase inverters. Typical applications include brushless DC and permanent-magnet synchronous motor drives, digital switched-mode power supplies and inverters, automotive body and powertrain subsystems (leveraging AEC-Q100 qualification), and industrial automation equipment requiring deterministic closed-loop control. When designing with this device, budget for a clean 3.3 V rail with local decoupling and plan pin multiplexing early - the 44-pin package concentrates many peripheral functions on shared pins, so peripheral pin selection must be mapped before layout. This page synthesizes distributor pricing, drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP512GM304-I/ML

DSPIC33EP512GM304-I/ML - 70 MIPS 512KB Flash DSC | Microchip

The Microchip Technology DSPIC33EP512GM304-I/ML is a 16-bit digital signal controller (DSC) from the dsPIC33EP512GM304 family, delivering up to 70 MIPS performance, 512 KB of Flash program memory, and 48 KB of RAM in a 44-pin QFN (8x8 mm) package with exposed pad. A digital signal controller combines the computational architecture of a microcontroller with the signal-processing capability of a DSP. Within the power management hierarchy of embedded systems, a DSC such as the dsPIC33EP sits above a general-purpose MCU by adding a DSP engine, hardware multipliers, accumulators, and barrel shifter, making it the natural choice for closed-loop control and real-time signal processing. Key features include the 70 MIPS dsPIC DSC core with integrated DSP instruction set, 12-bit ADC for precision analog acquisition, multiple UART/SPI/I2C communication interfaces, PWM outputs for motor control, quadrature encoder interface (QEI) inputs, and integrated op-amps that reduce external component count. The CMOS process keeps active power low while sustaining real-time performance. Architecturally, the device uses a 24-bit instruction word, multiple internal bus architectures, and a barrel shifter for fast bit manipulation. Boundary-scan capability supports in-circuit testing, and the In-Circuit Serial Programming (ICSP) interface allows field firmware updates. Program memory is organized as 170K x 24-bit words, consistent with the 512 KB Flash density reported by distributors. Typical applications include precision motor control (BLDC, PMSM, stepper), digital power conversion, industrial automation, and sensor signal conditioning where the on-chip op-amps and ADC feed a fast control loop. A key design consideration: this is a 3.3 V device, so level shifting is required when interfacing with 5 V peripherals. The exposed-pad QFN also needs a solid ground pour for thermal and signal-integrity performance. This page synthesizes distributor pricing context, same-package drop-in family alternatives, and practical design notes not found in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP512GM304-I/PT

DSPIC33EP512GM304-I/PT - 16-bit 70 MIPS DSC 512KB Flash | Microchip

The Microchip Technology DSPIC33EP512GM304-I/PT is a 16-bit digital signal controller (DSC) from the dsPIC33EP GM family featuring a 70 MIPS dsPIC DSC core, 512KB (170K x 24) of flash program memory, 16KB of RAM, and integrated motor-control peripherals, housed in a 44-pin TQFP (10x10 mm) surface-mount package operating from a 3.3V supply across the -40C to +85C industrial temperature range. A digital signal controller (DSC) combines the computational strengths of a microcontroller (MCU) with the DSP capabilities of a digital signal processor in a single device. Within the embedded-processing hierarchy, a DSC sits between general-purpose MCUs and dedicated DSPs, making it the preferred choice when real-time control loops - such as field-oriented motor control or digital power conversion - demand multiply-accumulate throughput alongside standard MCU peripherals. The broader taxonomy is: DSC -> microcontroller -> embedded processor -> semiconductor. Key differentiating specifications include the 70 MIPS core running at 3.0V to 3.6V, 512KB of self-programmable flash supporting in-field firmware updates, dual CAN 2.0B modules, four integrated operational amplifiers (OpAmps), and rich motor-control peripherals: 12 PWM channels, four input capture / output compare units, and two quadrature encoder interface (QEI) modules for closed-loop servo feedback. The integrated 12-bit ADC with simultaneous multi-channel sampling reduces external analog component count in inverter designs. Architecturally, the dsPIC33E core uses a modified Harvard pipeline with a 24-bit instruction word, hardware DSP multiply-accumulate (MAC) unit, DO and REPEAT loop instructions, and a flexible DMA controller that offloads data movement between peripherals and RAM - critical for sustaining high sample-rate control loops without CPU overhead. Typical applications include brushless DC and PMSM motor drives, digital power supplies and solar inverters, sensor signal conditioning in industrial automation, and general embedded control requiring DSP math. The two QEI interfaces directly accept encoder inputs for dual-axis motion control. Design consideration: the device is supplied from a 3.3V rail; ensure decoupling capacitors on all VDD pins, a stable AVDD supply for ADC accuracy, and verify MCLR/VPP programming requirements with PICkit or ICD tools. This page synthesizes distributor pricing from DigiKey, Mouser and LCSC, verified drop-in alternatives within the dsPIC33EP family, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

DSPIC33EP512GM304T-I/ML

DSPIC33EP512GM304T-I/ML - 70 MIPS 512KB DSC | Microchip

The Microchip Technology DSPIC33EP512GM304T-I/ML is a 16-bit dsPIC33EP digital signal controller (DSC) delivering up to 70 MIPS performance with 512 KB (170K x 24) of FLASH program memory and 16 KB of RAM, housed in a 44-pin QFN (8x8 mm, 0.9 mm height) exposed-pad package. A digital signal controller combines the compute architecture of a microcontroller with the math acceleration of a DSP. Within the power-management hierarchy of embedded processors, the dsPIC33E family sits above general-purpose PIC16/PIC18 MCUs and below 32-bit application processors, targeting real-time control loops that need both deterministic interrupt latency and hardware multiply-accumulate (MAC) throughput for filtering, transforms, and field-oriented control. Key features include the 70 MIPS dsPIC33E core, 12-channel Motor Control PWM (MCPWM), 8 input captures and 8 output compares, 2 quadrature encoder interfaces (QEI), and 4 DMA channels for low-overhead data movement. The GM3xx peripheral set adds four on-chip operational amplifiers, a Charge Time Measurement Unit (CTMU), and a Pattern Generator (PTG), differentiating it from the GP (general purpose) variants of the same die. Architecturally, the device uses a modified Harvard 16-bit core with a 24-bit instruction word, barrel shifter, DSP engine with 40-bit accumulators, and dual operand fetch, enabling single-cycle MAC operations. The 512 KB self-programming FLASH supports in-field firmware updates, and 5 V-tolerant digital inputs simplify interfacing with legacy 5 V peripherals on a 3.3 V rail. Typical applications include precision BLDC and PMSM motor control (leveraging the MCPWM, QEI, and op-amp peripherals), digital power supplies and PFC stages, and sensor signal conditioning where the CTMU and integrated op-amps reduce external component count. Design consideration: the 44-QFN exposed pad must be soldered to a solid ground pour for thermal dissipation and signal integrity; decouple all VDD/VDDCORE pins with 0.1 uF ceramics placed within 2 mm of the pins, and respect the VDDCORE capacitor requirement per the family datasheet (70000689d). This page synthesizes drop-in alternatives, comparison tables, application guidance, and design notes not found on distributor listing pages, with all core specifications traced to Microchip and distributor data.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

DSPIC33EP32MC502T-I/SS - 16-bit DSC, 32KB Flash | Microchip

DSPIC33EP32MC503-H/TL - 16-bit DSC, 32KB Flash, Motor Control | Microchip

DSPIC33EP32MC503-I/M5 - 70 MIPS 16-bit DSC | Microchip Technology

DSPIC33EP32MC503-I/TL - 16-bit 70 MIPS DSC 32KB Flash | Microchip

DSPIC33EP32MC503T-E/TL - 16-bit 60 MIPs DSC, 32KB Flash | Microchip

DSPIC33EP32MC503T-I/TL - 70 MIPS Motor Control DSC | Microchip

DSPIC33EP32MC504-E/MV - 60 MIPS Motor Control DSC | Microchip

DSPIC33EP32MC504-E/TL - 60 MIPS 16-bit DSC, 32KB Flash | Microchip

DSPIC33EP32MC504-H/ML - 16-bit 70 MIPS DSC, 32KB Flash | Microchip

DSPIC33EP32MC504-H/PT - 16-bit 60MIPS DSC 32KB Flash TQFP-44 | Microchip

DSPIC33EP32MC504-H/TL - 70MIPS 16-bit Motor Control DSC | Microchip

DSPIC33EP32MC504-I/ML - 70 MIPS 16-bit DSC, QFN-44 | Microchip

DSPIC33EP32MC504-I/MV - 16-Bit 70 MIPS DSC, 32KB Flash | Microchip

DSPIC33EP32MC504T-E/ML - 60MIPS 16-bit DSC, 32KB Flash | Microchip

DSPIC33EP32MC504T-E/PT - 16-bit 60 MIPS DSC, 44-TQFP | Microchip

DSPIC33EP32MC504T-E/TL - 60 MIPs 16-bit DSC, 32KB Flash | Microchip

DSPIC33EP32MC504T-I/MV - 16-bit 70 MIPS DSC, 32KB Flash | Microchip

DSPIC33EP32MC504T-I/TL - 16-bit DSC 32KB Flash 60MHz | Microchip

DSPIC33EP512GM304-E/ML - 16-bit DSC 512KB Flash 60 MIPS | Microchip

DSPIC33EP512GM304-E/PT - 70 MIPS 16-bit DSC, 512KB Flash | Microchip

DSPIC33EP512GM304-H/PT - 70 MIPS 16-Bit DSC 512KB Flash | Microchip

DSPIC33EP512GM304-I/ML - 70 MIPS 512KB Flash DSC | Microchip

DSPIC33EP512GM304-I/PT - 16-bit 70 MIPS DSC 512KB Flash | Microchip

DSPIC33EP512GM304T-I/ML - 70 MIPS 512KB DSC | Microchip