Товары (44.000+)

INA106U - Gain 10 Differential Amplifier | Texas Instruments
INA106U

INA106U - Gain 10 Differential Amplifier | Texas Instruments

The Texas Instruments INA106U is a precision fixed-gain differential amplifier with a nominal gain of 10, 86 dB minimum common-mode rejection, and an 8-pin SOIC package. The device is designed for accurate differential measurement and signal conditioning where common-mode noise must be rejected before downstream amplification or conversion. Its monolithic construction combines a precision operational amplifier with laser-trimmed on-chip metal-film resistors. A differential amplifier is a circuit that amplifies the voltage difference between two input terminals while suppressing voltage common to both inputs. In the signal-chain hierarchy, differential amplification sits between sensors or front ends and higher-gain analog processing. The INA106 family is commonly used for bridge, current, and instrumentation-amplifier input stages where preserving small differential signals is more important than accepting large common-mode signals. Key documented features include accurate gain of ±0.025% maximum, common-mode rejection of 86 dB minimum, and nonlinearity of 0.001% maximum. The laser-trimmed resistor network is intended to maintain accurate gain and common-mode rejection over temperature. The manufacturer describes applications including a gain-of-10 differential amplifier, a -10 amplifier, and a +11 amplifier configuration. The available INA106 family packages include 8-pin plastic DIP and SOIC options, while INA106U specifically denotes the SOIC ordering variant. The internal architecture is important because the matched resistor network determines gain accuracy and common-mode behavior. Unlike a discrete implementation using an operational amplifier and four external resistors, the integrated approach reduces resistor-matching variability and simplifies the physical circuit. The device should be evaluated against its complete datasheet electrical limits, including supply voltage, input range, output swing, frequency response, and temperature limits. Typical applications include precision bridge excitation and sensing, instrumentation front ends, current measurement, sensor signal conditioning, and rejection of common-mode noise in industrial control systems. The SOIC-8 package is suitable for conventional surface-mount assembly, but exposed thermal performance and output-drive limits still depend on the exact operating conditions. For layout, keep input traces short and symmetric, provide a clean reference connection, and place input filtering close to the amplifier. Confirm common-mode and output-swing limits before selecting external gain resistors or adding downstream gain. The fixed internal gain also means changing the system gain generally requires a different amplifier rather than an external resistor adjustment. This page combines the verified Texas Instruments product and datasheet information, distributor references, package guidance, and practical selection considerations. It is intended to help engineers identify whether the INA106U fixed-gain architecture matches the required accuracy, common-mode rejection, package, and supply conditions.

Запрос цены Контакты
INA106UG4 - Gain 10 Differential Amplifier | Texas Instruments
INA106UG4

INA106UG4 - Gain 10 Differential Amplifier | Texas Instruments

The Texas Instruments INA106UG4 is a precision, fixed-gain differential amplifier with a gain of 10, housed in an 8-pin SOIC package. It integrates a precision operational amplifier with laser-trimmed on-chip metal-film resistors, providing a compact way to amplify small differential signals. The monolithic gain stage is intended for instrumentation systems where a fixed gain of 10 is useful and external resistor matching is undesirable. A differential amplifier is an analog signal-conditioning circuit that responds to the voltage difference between two inputs while rejecting voltage common to both inputs. In the signal-chain hierarchy, the INA106UG4 belongs to the instrumentation amplifier family, combining differential amplification, fixed-gain accuracy, and common-mode rejection in one integrated package. This simplifies precision measurement designs compared with a discrete operational amplifier and matched external resistor network. The defining feature of the INA106UG4 is its gain of 10, implemented with on-chip metal-film resistors that are laser trimmed for accurate gain and high common-mode rejection. Excellent resistor tracking maintains gain accuracy and common-mode rejection over temperature. These characteristics make the device appropriate for sensor interfaces, bridge-amplifier signal paths, and instrumentation requiring repeatable differential-to-single-ended conversion. The INA106 architecture combines a precision operational amplifier with integrated gain-setting elements. Because the gain is fixed internally, designers do not need to select and match external resistors to obtain a gain of 10. The 8-pin SOIC package supports conventional surface-mount assembly and provides a practical option for compact analog boards requiring more integration than a basic single-ended op amp. Typical uses include low-level sensor conditioning, differential measurement interfaces, industrial instrumentation, and analog test equipment. In a bridge-based measurement, the amplifier can increase the differential bridge output before an ADC or downstream signal-processing stage. Its fixed gain simplifies gain planning, although the complete system must still satisfy input common-mode range, output swing, supply-voltage, and noise requirements. When laying out an INA106UG4 circuit, use a quiet ground reference and route differential inputs as a compact, symmetrical pair to minimize conversion of common-mode noise into differential error. Place input and output decoupling capacitors according to the manufacturer datasheet and avoid long unprotected traces around high-impedance source nodes. Verify signal polarity before applying large inputs because the fixed gain also amplifies offset and noise. This product page combines the manufacturer's device description and ordering information with package details, application guidance, parameter-by-parameter comparison, and practical design notes. It helps engineers distinguish the INA106UG4 from other differential-amplifier options while focusing on verified gain, architecture, package, sourcing, and circuit-integration considerations.

Запрос цены Контакты
INA110KP - Fast-Settling FET-Input Instrumentation Amplifier | TI
INA110KP

INA110KP - Fast-Settling FET-Input Instrumentation Amplifier | TI

Texas Instruments INA110KP is a monolithic FET-input instrumentation amplifier with internal gains of 1, 10, 100, 200, and 500 V/V, a 2.5 MHz bandwidth, and a 17 V/µs slew rate. The device uses a current-feedback topology and laser-trimmed input stage for accurate, fast-settling signal amplification. It is packaged in a 16-pin plastic DIP (PDIP). An instrumentation amplifier is a differential amplifier optimized for low-level measurements. Its three-amplifier or feedback architecture provides high input impedance, accurate differential gain, and rejection of common-mode voltage. INA110KP is designed for applications where sensor outputs are small, impedance may be high, and measurement speed must exceed that of many precision instrumentation amplifiers. Internal gain-setting resistors simplify implementation by supporting gains of 1, 10, 100, 200, and 500 V/V. Maximum input bias current is 50 pA, helping preserve accuracy with high-impedance sources. The amplifier also provides a minimum common-mode rejection of 106 dB at 10 kHz, low gain drift of 50 ppm/°C, and low offset drift of 2 µV/°C. The current-feedback circuit topology supports a 2.5 MHz bandwidth and 17 V/µs slew rate. According to the manufacturer product page, the INA110 settles to within 0.01% in 4 µs, making it suitable for high-speed and multiplexed-input data-acquisition systems where accurate settling is required after each channel selection. Typical uses include bridge and strain-gauge signal conditioning, high-impedance sensor interfaces, multiplexed measurement systems, laboratory instrumentation, industrial monitoring, and precision current or voltage measurements. The low input bias current is especially useful when source resistance is high enough for input leakage to affect measurement accuracy. Designers should follow the manufacturer pin-description and typical-application circuits when assigning inputs, gain connections, supply bypass capacitors, and output connections. Input filtering and protection must account for the very low 50 pA maximum input bias current. Decoupling and grounding should be arranged to minimize parasitic feedback around the high-bandwidth amplifier. This product page combines the manufacturer's core performance data with application guidance, practical design notes, and a package-matched comparison framework. It is intended to help engineers evaluate settling behavior, gain selection, source impedance, common-mode range, and layout before integrating INA110KP into a measurement system.

Запрос цены Контакты
INA110KPG4 - Fast-Settling FET Instrumentation Amplifier | Texas Instruments
INA110KPG4

INA110KPG4 - Fast-Settling FET Instrumentation Amplifier | Texas Instruments

Texas Instruments INA110KPG4 is a fast-settling, FET-input instrumentation amplifier packaged in a 16-pin PDIP. It accepts supply voltages from ±6 V to ±18 V, provides single-ended output, supports gains of 1, 10, 100, or 1000, and features a 2.5 MHz bandwidth with 500 µV input offset voltage. The device is intended for precision signal-conditioning systems that require high input impedance, low bias current, and accurate differential measurement. An instrumentation amplifier is a specialized amplifier optimized for measuring the difference between two low-level input signals. Its internal architecture provides high input impedance, low output impedance, excellent common-mode rejection, and stable gain set by a resistor or selectable internal gain network. This makes the INA110KPG4 useful when sensor outputs are small, source impedance is high, or the measurement must reject common-mode interference appearing equally on both inputs. The INA110KPG4 combines a 2.5 MHz bandwidth with fast settling, making it suitable for measurement channels that need to respond quickly after a control, excitation, or sensor input changes. Its FET-input stage supports low input bias current, while the 500 µV input offset specification defines the dc error budget for high-gain measurements. The 16-pin PDIP format is appropriate for through-hole prototype boards, laboratory instrumentation, educational systems, and established production assemblies that accept a dual-inline footprint. The amplifier can operate with positive and negative supply rails, allowing the output to remain centered around ground while processing bipolar sensor signals. A reference connection permits output-voltage shifting when the system requires a nonzero midpoint. The available gains of 1, 10, 100, and 1000 allow the same device architecture to cover both high-level measurements and small differential signals without changing packages. Typical uses include bridge-transducer amplification, low-current measurement, biomedical instrumentation, industrial sensor interfaces, laboratory measurement systems, and data-acquisition modules. The device is especially useful when the source impedance is too high for a conventional voltage-amplifier input or when the measured differential signal is much smaller than the surrounding common-mode voltage. When laying out a board, keep the input and output paths short, provide a stable low-noise reference network, and observe the supply-voltage limits of ±6 V to ±18 V. Breadboard connections and long unprotected input tracks should be avoided because leakage, contamination, and parasitic capacitance can degrade accuracy and settling performance. This product page combines package details, operating limits, application guidance, and verified drop-in alternatives. It also provides practical design notes for a legacy bipolar-supply instrumentation amplifier used in sensitive analog measurement systems.

Запрос цены Контакты
INA110KU - 2.5 MHz Fast-Settling Amplifier | Texas Instruments
INA110KU

INA110KU - 2.5 MHz Fast-Settling Amplifier | Texas Instruments

Texas Instruments INA110KU is a monolithic FET-input instrumentation amplifier with 2.5 MHz bandwidth, 4 us settling to 0.01%, and 17 V/us slew rate, housed in a 16-pin SOIC package. It accepts a 12 V to 36 V supply and provides internal gain settings of 1, 10, 100, 200, and 500 V/V. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage difference between two inputs while rejecting common-mode interference. The INA110 belongs to the instrumentation amplifier hierarchy within analog amplifiers and signal-chain ICs. Its current-feedback topology, laser-trimmed input stage, very high input impedance, and low input bias current make it suitable for measuring small differential signals through balanced sensors, bridges, and multiplexed data-acquisition inputs. Key features include selectable internal gains of 1, 10, 100, 200, and 500 V/V, a stated input offset voltage of 1 mV, and 2.5 MHz bandwidth. The fast 4 us settling time supports systems that change gain or source between measurements quickly. Input filtering and protection can be placed directly at the high-impedance inputs without loading the source, while the 12 V to 36 V supply range supports higher-compliance analog systems. The current-feedback architecture is intended to provide good dynamic performance while the laser trimming improves gain accuracy and DC behavior. Internal gain-set resistors reduce the number of external components required for fixed-gain designs. Because the device contains FET input stages, it offers very high input impedance and low bias current; this is useful when the source impedance is high or when source resistance differs between the two inputs. Typical applications include high-speed data acquisition, multiplexed sensor measurement, bridge-amplifier interfaces, current measurement, laboratory instrumentation, and industrial signal conditioning. The 4 us settling time is particularly useful when sequential channels must be measured rapidly, while the internal gain choices cover low-level sensor outputs through higher-amplitude differential signals. For layout, keep input and feedback connections short, use symmetric routing between the differential inputs, and place input protection or filtering close to the corresponding pins. Check the external feedback-network requirements for each selected gain and confirm that source impedances remain compatible with the required common-mode range and settling performance. This page combines the manufacturer device specifications with application guidance, package information, replacement analysis, and design-focused comparisons. It highlights where the INA110KU fits in high-speed measurement systems and provides practical context for selecting among same-package alternatives before committing the SOL-16 footprint to a PCB layout.

Запрос цены Контакты
INA110KUG4 - 2.5 MHz Military Instrumentation Amplifier | Texas Instruments
INA110KUG4

INA110KUG4 - 2.5 MHz Military Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA110KUG4 is a single-circuit instrumentation amplifier packaged in a 16-pin SOIC. It is identified as a military-temperature-grade, gull-wing-lead device, and its listed gain-bandwidth product is 2.5 MHz. The INA110KUG4 is intended for systems that require a differential input stage, an adjustable-gain architecture, and a regulated output referenced to a low-impedance analog supply. An instrumentation amplifier is a precision analog building block that amplifies the voltage difference between two input signals while rejecting common-mode interference. Unlike a general-purpose operational amplifier, an instrumentation amplifier normally incorporates a high-impedance differential input stage, accurate gain-setting resistors, and a low-impedance output stage. Within the power-management and signal-chain hierarchy, it sits upstream of analog-to-digital converters, filters, and analog-to-digital output stages. The INA110KUG4 is classified by Texas Instruments as an instrumentation amplifier rather than a standalone operational amplifier. Its adjustable external gain resistor allows the same circuit topology to support multiple sensitivity ranges, provided that resistor values remain suitable for the required bandwidth and stability. The 2.5 MHz gain-bandwidth figure makes the device relevant to moderate-bandwidth sensor conditioning rather than only static measurement systems. Because the INA110KUG4 uses a precision differential input stage, it is suitable for conditioning low-level sensor outputs where common-mode voltage varies relative to the measurement. Typical signal sources include pressure bridges, strain gauges, thermocouples when paired with suitable cold-junction compensation, and high-impedance sensing elements. A reference pin also permits the output voltage to be shifted when the receiving circuit cannot tolerate a ground-centered signal. Common applications include industrial process monitoring, laboratory instrumentation, data acquisition, medical monitoring equipment, and portable measurement systems. In a typical bridge-sensor circuit, the INA110KUG4 amplifies the small differential bridge voltage while rejecting much of the common excitation voltage. The output can then feed an analog-to-digital converter or an analog filter. When laying out a board for the INA110KUG4, keep the gain-setting resistor close to its corresponding device pin and use a quiet analog ground for the reference and supply-return connections. Place input and reference decoupling capacitors near the package, and route sensitive input traces away from digital clocks, switching-regulator nodes, and high-current return paths. This page combines the manufacturer part identity, package information, commercial listings, and comparison data for the INA110KUG4 with application guidance, layout cautions, and practical sourcing information. Review the complete manufacturer datasheet for the definitive pin configuration, electrical limits, gain equation, and recommended operating conditions before releasing a production design.

Запрос цены Контакты
INA110SG - Fast-Settling FET-Input Amplifier | Texas Instruments
INA110SG

INA110SG - Fast-Settling FET-Input Amplifier | Texas Instruments

Texas Instruments INA110SG is a single-channel, monolithic FET-input instrumentation amplifier with a current-feedback topology, laser-trimmed input stage, internal gain-set resistors, and a 16-CDIP package. It supports gains of 1, 10, 100, 200, and 500 V/V, reaches 0.01% settling in 4 microseconds, and provides a typical bandwidth of 2.5 MHz. Maximum input bias current is 50 pA, while common-mode rejection reaches at least 106 dB at 10 kHz. An instrumentation amplifier is a specialized analog amplifier designed to amplify small differential signals while rejecting large common-mode voltages. Its internal architecture provides matched input devices, high input impedance, and stable gain behavior, making it part of the broader operational-amplifier and signal-conditioning hierarchy. INA110 applications include sensor-interface circuits, bridge amplifiers, current measurement, laboratory instrumentation, and multiplexed data-acquisition systems where low bias current, high common-mode rejection, and rapid settling are important. Internal gain resistors permit selectable gains of 1, 10, 100, 200, and 500 V/V without external feedback resistors. The laser-trimmed input stage supports high accuracy, with very low gain drift of up to 50 ppm per degree Celsius and input offset drift of 2 microvolts per degree Celsius. The low maximum bias current of 50 pA is particularly useful with high-impedance sources and electrostatic sensors. A minimum common-mode rejection of 106 dB at 10 kHz improves rejection of interference shared by both input terminals. The INA110 uses a current-feedback architecture rather than a conventional voltage-feedback topology. This architecture supports fast settling and broad usable bandwidth, while the 2.5 MHz typical bandwidth provides useful signal bandwidth for precision measurement systems. The manufacturer identifies fast settling as especially valuable in high-speed and multiplexed-input data-acquisition systems, where insufficient settling between channel selections can create measurement errors. The INA110SG operates from dual supplies with a typical total supply of plus or minus 15 V, a minimum of plus or minus 6 V, and a maximum of plus or minus 18 V. Typical applications include low-current sensor amplification, precision bridge excitation and readout, isolated or high-impedance measurement front ends, portable instrumentation, and multi-channel acquisition systems. The low bias current helps preserve sensor accuracy, while the 106 dB common-mode rejection helps suppress noise and power-supply-related disturbances appearing equally on both inputs. The 4-microsecond settling specification is valuable when many input channels must be sampled rapidly. Designers should verify supply polarity, common-mode range, gain selection, input protection, and output swing against the manufacturer datasheet before finalizing the analog path. Instrumentation-amplifier layouts should use short input traces, guard techniques for high-impedance nodes, and symmetric routing to minimize parasitic imbalance. Decoupling capacitors should be placed close to the supply pins, while unused gain-select pins must be connected according to the recommended configuration for the intended gain. This product overview combines the INA110SG architecture, verified performance characteristics, application guidance, package constraints, and drop-in alternatives into an engineering-focused reference. It also highlights the trade-offs involved when replacing a military-temperature ceramic CDIP with a lower-temperature plastic or ceramic DIP implementation.

Запрос цены Контакты
INA111AP - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments
INA111AP

INA111AP - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA111AP is a high-speed, FET-input instrumentation amplifier with a gain range from 1 to over 1,000 V/V, 2 MHz bandwidth at a gain of 10, and an 8-pin plastic DIP package. It also provides a maximum input bias current of 20 pA, maximum input offset voltage of 500 µV, and minimum common-mode rejection of 106 dB. An instrumentation amplifier is a precision amplifier designed to amplify small differential signals while rejecting large common-mode voltages. Its internal differential amplifier stages provide accurate gain, high input impedance, and balanced inputs, making the category well suited to sensor bridges, strain gauges, biomedical instrumentation, and industrial measurement systems. Within the signal-chain hierarchy, the INA111AP belongs to the amplifier IC family and specifically serves as a differential instrumentation amplifier. A single external resistor sets the closed-loop gain, simplifying adjustment while preserving the performance of the internal current-feedback architecture. The gain can range from 1 to over 1,000 V/V, allowing the same device to amplify millivolt-level sensor outputs or larger instrumentation signals. Laser trimming supports low offset voltage, with a maximum of 500 µV, and maximum offset-voltage drift of 5 µV/°C. The current-feedback topology extends bandwidth to 2 MHz at a gain of 10 and provides a settling time of 4 µs to 0.01% at a gain of 100. These speed characteristics make the INA111AP suitable for measurement systems that need better transient response than conventional voltage-feedback instrumentation amplifiers, although bandwidth decreases as the selected gain increases. Typical applications include precision bridge excitation and readout, low-current sensor interfaces, laboratory instrumentation, diagnostic equipment, and industrial control systems. The wide supply range of 12 V to 36 V supports higher-voltage industrial systems, while the FET-input architecture minimizes input-bias-current error when measuring high-impedance sources. For reliable circuit implementation, place the gain-setting resistor close to the RG pins, provide stable input and output decoupling, and keep sensitive input traces away from high-current switching paths. Verify settling time and bandwidth at the actual selected gain because both performance characteristics depend on gain, supply voltage, and signal amplitude. This page combines manufacturer specifications, package and pin guidance, application engineering notes, and drop-in replacement analysis to support faster component selection and PCB implementation. It identifies where the INA111AP fits in measurement systems and clarifies the practical limits engineers should check before finalizing a precision signal chain.

Запрос цены Контакты
INA111AU - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments
INA111AU

INA111AU - High-Speed FET-Input Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA111AU is a high-speed FET-input instrumentation amplifier with 2 MHz bandwidth, 17 V/us slew rate, and a 16-pin SOIC package. It is designed for precision signal conditioning where low input bias current, high common-mode rejection, and fast settling are important. The device uses a current-feedback architecture and provides a gain range of 1 to 1000 through an external gain-setting resistor. An instrumentation amplifier is a differential analog amplifier designed for measuring small differential signals while rejecting large common-mode voltages. It is commonly used to amplify sensor outputs, bridge signals, strain-gauge outputs, and low-level biological signals. The INA111AU belongs to the instrumentation amplifier hierarchy, which provides differential input handling and gain control in a compact analog front end. The FET input stage reduces input bias current to 20 pA maximum, making the INA111AU suitable for high-impedance sources. Its maximum input offset voltage is 500 uV, and its maximum input offset voltage drift is 5 uV/C. The minimum common-mode rejection ratio is 106 dB. The device offers a 2 MHz bandwidth and 17 V/us slew rate, supporting faster response than many general-purpose precision instrumentation amplifiers. The INA111AU uses a three-operamplifier instrumentation-amplifier architecture with laser-trimmed resistors. A single external resistor sets the closed-loop gain, allowing gain values from 1 to 1000 when the specified gain-setting resistor is used. This combination of differential input, adjustable gain, and high input impedance makes the device suitable for conditioning signals from pressure, temperature, current, and resistive bridge sensors. Typical applications include bridge-transducer amplification, portable measurement systems, instrumentation interfaces, industrial sensor conditioning, and precision data-acquisition front ends. The low bias current helps preserve sensor-source accuracy, while the 106 dB minimum common-mode rejection helps suppress noise and supply disturbances that are common to both differential inputs. Designers should keep input and feedback traces short, provide suitable bypassing close to the power pins, and verify the external gain resistor against the datasheet gain equation. Input common-mode and output swing limits must be checked at the selected supply voltage and gain. The manufacturer datasheet should be used for the complete pin description, recommended application circuit, and gain-setting calculations. This product page combines the manufacturer specifications, verified sourcing information, package details, application guidance, and engineering-oriented design notes. It helps engineers evaluate the INA111AU for high-impedance measurement circuits while identifying the key electrical limits that determine signal fidelity and system compatibility.

Запрос цены Контакты
INA111AU/1K - High-Speed FET Instrumentation Amplifier | TI
INA111AU/1K

INA111AU/1K - High-Speed FET Instrumentation Amplifier | TI

The Texas Instruments INA111AU/1K is a high-speed, FET-input instrumentation amplifier in a 16-pin SOIC package. It provides a 2 MHz bandwidth at a gain of 10, settles to within 0.01% in 4 microseconds at a gain of 100, and accepts input bias current below 20 pA. A single external resistor sets the gain from 1 to more than 1000, making the device suitable for precision sensor interfaces and low-level differential measurements. An instrumentation amplifier is a differential analog amplifier optimized for measuring small signals superimposed on a larger common-mode voltage. Its internal architecture provides high input impedance, accurate differential gain, and strong common-mode rejection without requiring the user to match closely coupled input resistors. The INA111 belongs to the amplifier hierarchy as a FET-input instrumentation amplifier, a precision analog IC, and ultimately a signal-conditioning semiconductor used between sensors and data-conversion or control systems. Key electrical features include input bias current below 20 pA, maximum input offset voltage of 500 microvolts, maximum offset drift of 5 microvolts per degree Celsius, and common-mode rejection of at least 106 dB. The low input current simplifies filtering for high-impedance sensors, while the high CMRR suppresses common-mode interference. The current-feedback architecture supports extended bandwidth and rapid settling, which helps preserve accuracy when gain changes occur in measurement systems. The device uses one external gain-setting resistor, allowing designers to select gain without a resistor network. Because the achievable bandwidth depends on gain, the INA111 is especially useful where measurement speed must be balanced against signal amplification. Its offset and drift characteristics also make it suitable for bridge transducers, biomedical instrumentation, and industrial data-acquisition systems operating across the manufacturer-specified temperature range of -40°C to +85°C. Typical uses include medical instrumentation, industrial data acquisition, precision bridge-sensor interfaces, current measurement, and low-level differential signal conditioning. In these applications, the amplifier can sit between a sensor and an ADC while rejecting common-mode voltage present on both sensor lines. The design should preserve the common-mode voltage within the device's operating limits and provide appropriate filtering at the inputs. For PCB implementation, place the gain resistor close to the gain-setting pins, maintain short and symmetric input traces, and decouple the supply pins near the device. Input filtering components should have closely matched impedances if their tolerance could unbalance the differential signal. Because the offset specification is referenced to a particular gain, recalculate accuracy when the external gain resistor differs from the manufacturer's test condition. This product page combines the manufacturer's electrical and package information with practical design guidance, pin and footprint considerations, application fit, and drop-in replacement analysis for engineers evaluating the INA111AU/1K in new and existing analog signal-chain designs.

Запрос цены Контакты
INA111BP - 2MHz FET-Input Instrumentation Amp | Texas Instruments
INA111BP

INA111BP - 2MHz FET-Input Instrumentation Amp | Texas Instruments

Texas Instruments INA111BP is a high-speed, FET-input instrumentation amplifier with 2 MHz bandwidth at a gain of 10, 17 V/us slew rate, and low input bias current of 20 pA maximum, housed in an 8-pin PDIP package. The single-circuit device supports externally selected gains from 1 to more than 1000 through one resistor and uses a current-feedback topology to maintain speed at higher closed-loop gains. An instrumentation amplifier is a specialized analog signal-conditioning IC designed to amplify small differential sensor signals while rejecting common-mode voltage. The INA111 belongs to the instrumentation-amplifier hierarchy, which combines differential input, high input impedance, precise gain setting, and common-mode rejection. Its FET inputs suit high-impedance transducers, while laser-trimmed offset characteristics support accurate measurement of low-level signals. Key features include a 20 pA maximum input bias current, 500 uV maximum offset voltage, 5 uV/°C maximum offset drift, and 106 dB minimum common-mode rejection. The INA111 settles to 0.01% in 4 us at a gain of 100. These characteristics make the device useful where fast acquisition and high source impedance must coexist with accurate differential amplification. The current-feedback architecture differentiates the INA111 from conventional voltage-feedback instrumentation amplifiers. It provides extended bandwidth of 2 MHz at a gain of 10 and a 17 V/us high slew rate, improving response to rapidly changing inputs. Gain is set by one external resistor, while the internal resistor network supports gain selections that do not require that external component. Typical applications include bridge-sensor signal conditioning, industrial process measurement, biomedical instrumentation, current-shunt monitoring, and precision data-acquisition systems. The low input bias current is particularly useful with high-impedance sources, while the 2 MHz bandwidth benefits sampled or multiplexed measurement systems requiring short acquisition times. When designing around the INA111BP, verify the input and output voltage limits, supply headroom, and common-mode range for the intended signal. Place the gain-setting resistor close to the appropriate RG pins, maintain symmetric input routing, and use adequate bypassing at the supply pins to preserve bandwidth and minimize added noise. This page combines verified manufacturer specifications, distributor pricing, same-package replacement guidance, comparison parameters, and practical design notes. It is intended to help engineers evaluate the INA111BP beyond a basic distributor listing while highlighting the checks required before substituting any pin-compatible device.

Запрос цены Контакты
INA111BU - 2 MHz FET-Input Instrumentation Amplifier | Texas Instruments
INA111BU

INA111BU - 2 MHz FET-Input Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA111BU is a single-channel, high-speed, FET-input instrumentation amplifier with a 2 MHz gain-bandwidth product, 17 V/us slew rate, and 106 dB CMRR. It operates from 6 V to 18 V and is supplied in a 16-pin SOIC package for surface-mount instrumentation and signal-conditioning systems. An instrumentation amplifier is a specialized analog amplifier designed to amplify small differential signals while rejecting common-mode noise and interference. Its typical signal path includes input buffers, a differential amplifier stage, and gain-setting elements. This three-op-amp topology belongs to the broader operational-amplifier hierarchy and is commonly used where sensor outputs, sensor inputs, and instrumentation need accurate differential measurement without excessive front-end complexity. The INA111BU uses FET inputs to reduce input bias current to less than 20 pA. This low-bias-current characteristic simplifies input filtering and limits circuitry around high-impedance sources. Its 2 MHz bandwidth supports higher-bandwidth measurement than precision-only instrumentation amplifiers, while the 17 V/us slew rate helps preserve large-signal response when operating at higher gains. The specified 106 dB CMRR supports effective rejection of common-mode voltage in industrial and test environments. The device accepts a 6 V to 18 V supply range and is specified from -40 C to +85 C. The 16-pin SOIC package provides a practical surface-mount option for acquisition boards, process-control equipment, medical instrumentation, and laboratory measurement systems. Pin assignments and recommended gain-setting component values should be taken directly from the pin-description and application circuits in the manufacturer datasheet. INA111BU is suited to bridge sensors, current shunts, precision current measurement, and low-level differential signal acquisition. The principal design trade-off is the relationship between closed-loop gain, bandwidth, output swing, and input common-mode range. Designers should confirm those limits for the intended gain and supply voltage before committing the PCB layout. This page combines the manufacturer product information with a structured technical comparison, practical design notes, verified source links, and identified replacement constraints. Use the Request a Quote form on this page for current commercial availability, lot-specific packaging, and sourcing requirements.

Запрос цены Контакты
INA111BUG4 - 2MHz FET-Input Instrumentation Amp | Texas Instruments
INA111BUG4

INA111BUG4 - 2MHz FET-Input Instrumentation Amp | Texas Instruments

The Texas Instruments INA111BUG4 is a high-speed, FET-input instrumentation amplifier with a gain-bandwidth product of 2 MHz, packaged in a 16-pin SOIC. It is designed for precision signal-conditioning applications that require amplification of low-level differential signals, particularly when the source impedance is high and input bias current must remain small. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode interference. The INA111 belongs to the FET-input instrumentation amplifier hierarchy, combining an instrumentation amplifier with low-bias-current transistor input circuitry. This topology supports accurate measurement from sources that would disturb conventional bipolar-input amplifiers. The INA111’s principal advantages include input bias current below 20 pA, operation across a -40°C to +85°C temperature range, and a 2 MHz gain-bandwidth product. Its FET inputs also reduce input loading, simplify input filtering, and make the device suitable for bridge, transducer, and current-sense measurements where source impedances range from approximately 2 kΩ to 50 kΩ. The SOIC-16 surface-mount package supports compact analog instrumentation. The three-op-amp instrumentation-amplifier architecture provides a practical balance between common-mode rejection, gain control, input impedance, and signal bandwidth. Gain is established externally, allowing one device to support multiple measurement ranges without changing its internal signal path. As with any precision amplifier, the useful bandwidth decreases as the selected gain increases, so the complete gain-versus-bandwidth characteristic must be considered in high-speed designs. Typical uses include bridge-transducer excitation and readout, precision current sensing, laboratory measurement interfaces, medical instrumentation, and low-level differential signal acquisition. The high input impedance is particularly useful when the source is a sensor or resistive network whose output impedance is much higher than the amplifier input resistance. The device can therefore preserve source amplitude and reduce loading errors. For reliable operation, place the external gain-setting resistor and compensation network close to the device, keep input and feedback traces short, and use a quiet, low-impedance supply. Decoupling capacitors should be positioned directly beside the supply pins, while analog and digital ground returns should follow the manufacturer’s recommended layout and grounding arrangement. This product page combines the manufacturer’s INA111 documentation with application guidance, package information, verified source links, and replacement considerations. It is intended to help engineers identify suitable signal-chain applications, evaluate package and lifecycle constraints, and determine whether an existing PCB footprint can be reused without changing the analog layout.

Запрос цены Контакты
INA114AP - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA114AP

INA114AP - 1MHz Precision Instrumentation Amplifier | Texas Instruments

The Texas Instruments INA114AP is a precision instrumentation amplifier featuring 1 MHz bandwidth, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and approximately 3 mA operating current in an 8-pin PDIP package. It is designed for low-level differential measurements where sensor outputs are small and common-mode voltage, noise, and offset must be controlled carefully. The INA114AP uses a general-purpose three-op-amp architecture that accepts differential input signals and provides a scaled, referenced output for downstream conversion or control. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode voltage and providing controlled gain. The INA114 family belongs to the broader operational amplifier hierarchy as an instrumentation amplifier, precision analog IC, signal-conditioning IC, and power-management-dependent semiconductor device. This makes it suitable for bridge sensors, load cells, thermocouples, current shunts, and other transducers whose useful output occupies only a small portion of the applied voltage. The key electrical benefits of the INA114AP include a 1 MHz gain-bandwidth product, maximum input offset voltage of 50 µV, maximum offset drift of 0.25 µV/°C, maximum input bias current of 2 nA, and common-mode rejection of at least 115 dB. Its input-noise density is 11 nV/√Hz, making it effective for low-amplitude signals where broadband amplifier noise would otherwise obscure the measurement. Input overvoltage protection extends to ±40 V, while the supply range reaches ±18 V. These characteristics provide useful headroom in industrial and measurement systems where input transients and supply variations must be tolerated. The three-op-amp instrumentation-amplifier architecture supports accurate differential measurement with adjustable gain. A differential signal applied across the input terminals is amplified relative to ground or the voltage connected to the reference terminal. The gain depends on the external resistor connected to the gain-control pins, allowing the same device family to serve multiple transducer sensitivities. The 1 MHz bandwidth makes it suitable for applications extending beyond static measurement, including moderate-rate sensor acquisition and feedback control. Typical uses include load-cell and weighing systems, strain-gauge bridges, thermocouple interfaces, industrial pressure and flow sensors, biomedical instrumentation, and current-shunt measurements. The combination of low offset, high common-mode rejection, and low bias current is particularly valuable when the sensor is physically remote or when its leads pick up industrial noise. The 115 dB minimum common-mode rejection helps preserve a small differential signal even when both inputs ride on a larger common-mode voltage. A successful design must include adequate bypassing, careful routing of the two input paths, and a stable gain resistor. Place the input and supply capacitors close to their associated pins, keep the two input traces symmetrical, and avoid routing sensitive signals beside high-current or switching nodes. Select the gain resistor with suitable tolerance and temperature coefficient, and verify input and output swing against the actual sensor range. When the source impedance is high, account for amplifier bias-current error before interpreting the measured differential voltage. This page combines manufacturer specifications, exact-source pricing eligibility, package-level pin information, application guidance, and confirmed drop-in alternatives. It also highlights the distinction between a true same-footprint replacement and a merely similar instrumentation amplifier, helping engineers compare parts without relying on an incomplete cross-reference list.

Запрос цены Контакты
INA114AU - 1MHz Precision INA Amplifier | Texas Instruments
INA114AU

INA114AU - 1MHz Precision INA Amplifier | Texas Instruments

Texas Instruments INA114AU is a precision, single-amplifier instrumentation amplifier with 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption, housed in a 16-pin SOIC package. It supports dual supplies of ±2.25 V to ±18 V, provides internal input protection to ±40 V, and accepts a single gain-setting resistor for gains from 1 to 10,000. An instrumentation amplifier is a specialized amplifier that measures small differential signals while rejecting large common-mode voltages. The INA114 belongs to the precision instrumentation-amplifier hierarchy, where instrumentation amplifier, differential amplifier, analog signal-conditioning IC, and power-management-adjacent signal-chain component describe its principal function. Its three-op-amp architecture provides high input impedance and accurate differential gain, making it useful when the source resistance can vary or when a conventional op-amp differential circuit would suffer input-bias-current errors. Key features include 50 µV maximum offset voltage, 0.25 µV/°C maximum offset drift, 2 nA maximum input bias current, and 115 dB minimum common-mode rejection. A single external resistor selects gains from 1 to 10,000, while the 1 MHz gain-bandwidth product supports a 0.06 V/µs slew rate. These characteristics favor precision measurement rather than high-speed video amplification, although the 1 MHz bandwidth is sufficient for many industrial, medical, and instrumentation signals. The INA114 uses a three-op-amp internal architecture to establish differential gain while maintaining high input impedance. Laser trimming reduces offset errors, and the internal input protection network allows each input to withstand ±40 V without damage. With a typical 3 mA quiescent-current specification and operation down to ±2.25 V, the device supports dual-supply precision systems and single 5 V applications using suitable output-reference arrangements. Typical uses include bridge and strain-gauge conditioning, current-shunt measurement, laboratory instrumentation, ECG and physiological-signal acquisition, and industrial sensor interfaces. In a bridge circuit, the low offset and high common-mode rejection improve stability in the presence of long cables or supply variation. For sensor excitation, the amplifier converts a small millivolt-level differential output into a voltage suitable for an ADC. Designers must select the gain resistor carefully because its tolerance, temperature coefficient, and parasitic capacitance affect gain accuracy and bandwidth. Decoupling capacitors should be placed close to the supply pins, and the reference pin should be configured to provide the required output offset. Input filtering must preserve the required settling time because the internal protection resistors can combine with source capacitance to alter bandwidth. This product record consolidates verified manufacturer specifications, distributor information, drop-in alternatives, package details, and application guidance. It highlights the engineering trade-offs among gain, bandwidth, input protection, common-mode rejection, and supply requirements that are not apparent from the MPN alone.

Запрос цены Контакты
INA114AU/1K - 1MHz Precision Instrumentation Amplifier | TI
INA114AU/1K

INA114AU/1K - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114AU/1K is a single-channel precision instrumentation amplifier featuring 1 MHz gain-bandwidth product, 50 µV typical offset voltage, 11 nV/√Hz input noise density, and 3 mA power consumption. The device is packaged in a 16-pin SOIC and accepts supply voltages as low as ±2.25 V. A single external resistor sets the gain from 1 to 10,000, allowing the same circuit topology to serve low-gain signal conditioning and high-gain bridge-amplifier applications. An instrumentation amplifier is a specialized analog signal-conditioning IC designed to amplify the voltage difference between two inputs while rejecting common-mode signals. Its typical hierarchy is instrumentation amplifier → differential amplifier → analog amplifier → semiconductor. This category is especially useful when a low-level sensor output must be measured in the presence of a larger shared voltage. The INA114 uses a three-op-amp architecture, which provides high input impedance, flexible gain control, and accurate differential amplification. The INA114's principal electrical features include a 1 MHz gain-bandwidth product, 110 dB dynamic range as identified in the manufacturer listings, 50 µV typical offset, and 11 nV/√Hz input noise density. A single gain-setting resistor establishes gains between 1 and 10,000, eliminating the need for a resistor network. The device can operate with power supplies as low as ±2.25 V and supports dual supplies up to ±18 V. Internal input protection can withstand input voltages up to ±40 V without damage, adding robustness in industrial measurement systems. Internally, the INA114 uses a versatile three-op-amp instrumentation-amplifier arrangement. Its input stage preserves the differential signal while the output stage develops the selected gain and drives the output relative to the REF pins. The laser-trimmed internal resistors support low offset and consistent performance without user calibration. The manufacturer identifies the INA114 as a low-cost, general-purpose precision device, while its 1 MHz bandwidth allows it to handle signals substantially faster than static low-frequency sensor outputs. Typical uses include bridge and strain-gauge signal conditioning, current-shunt measurement, low-level sensor interfaces, laboratory instrumentation, and industrial process-control inputs. It is particularly appropriate when a sensor develops only millivolts or microvolts and common-mode voltage can be much larger than the desired signal. The adjustable gain also supports transducers with widely different output sensitivities without changing the surrounding analog topology. When laying out the circuit, connect the gain resistor between the designated RG pins and place input, supply, and reference bypassing capacitors close to the associated package pins. Keep sensitive input traces short, route them away from switching nodes, and use a stable low-noise reference when an offset voltage other than ground is required. Confirm input and output common-mode ranges over the complete supply range because the selected gain reduces allowable output swing. This page combines manufacturer specifications, exact-order information, a same-package electrical alternative, and practical design guidance. It also distinguishes reel-packaged ordering variants from genuinely different functions, helping engineers make a defensible selection without relying on package code alone.

Запрос цены Контакты
INA114BP - 1MHz Precision Instrumentation Amplifier | TI
INA114BP

INA114BP - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114BP is a precision three-op-amp instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV maximum offset voltage, and an 8-pin PDIP package. It supports gains from 1 to 10,000 through one external gain-setting resistor, while input protection tolerates voltages up to +/-40 V. Its low-noise and high-accuracy characteristics make it suitable for measuring small differential signals in industrial, medical, and test systems. An instrumentation amplifier is a specialized amplifier category designed to extract a small differential voltage while rejecting common-mode interference. Its internal three-op-amp architecture provides high input impedance and precise gain control, making it more effective than ordinary operational amplifiers in many sensor-front-end applications. Within the signal-chain hierarchy, it belongs to the broader family of amplifier ICs and analog signal-conditioning components. Key features include 11 nV/sqrt(Hz) input noise, 115 dB minimum common-mode rejection, 2 nA maximum input bias current, and 0.25 uV/degree C maximum input offset drift. The low offset voltage and drift reduce measurement errors in bridge, strain-gauge, and low-level current sensing systems. Internal input protection supports +/-40 V, helping the device tolerate transient overloads encountered outside the normal operating input range. The INA114 uses a versatile three-op-amp signal chain and accepts single or dual supply operation. Its gain is established with one external resistor, allowing a single circuit implementation to cover gain settings from 1 to 10,000. The 1 MHz bandwidth supports dynamic sensor signals while remaining appropriate for precision industrial instrumentation rather than very high-frequency signal extraction. Typical uses include 4-20 mA current-loop receivers, strain-gauge bridge amplifiers, isolated-signal front ends, precision current-shunt measurements, biomedical instrumentation, and laboratory measurement equipment. The device is particularly useful when the wanted differential signal is small relative to ground offsets or common-mode noise present at the input connectors. When designing the input stage, use an external gain resistor with suitable stability and thermal characteristics, keep input traces short, and connect the reference pin to a clean analog ground when unity gain is required. Check input common-mode range and output swing at every supply voltage before selecting the final gain, because bandwidth and output capability change with operating conditions. This page combines the device's precision specifications, application guidance, package information, replacement analysis, and practical design considerations to support faster component evaluation and more reliable front-end design.

Запрос цены Контакты
INA114BU - 1MHz Precision Instrumentation Amplifier | TI
INA114BU

INA114BU - 1MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA114BU is a precision three-op-amp instrumentation amplifier with 1 MHz gain-bandwidth performance, 50 uV input-offset voltage, 11 nV/√Hz input noise, and approximately 3 mA power consumption. The device is offered in a 16-pin SOIC surface-mount package for precision measurement systems requiring differential input amplification and single-resistor gain programming. An instrumentation amplifier is a specialized analog amplifier optimized for measuring small differential signals superimposed on large common-mode voltages. It belongs to the amplifier hierarchy as an instrumentation amplifier, differential amplifier, and analog signal-conditioning IC. Its internal three-op-amp architecture improves common-mode rejection and enables gains from 1 to 10,000 by selecting one external gain-setting resistor. This makes the INA114BU useful when a sensor, transducer, or measurement bridge produces a low-level differential output that must be amplified without amplifying system noise or supply variation equally. The most prominent INA114BU characteristics are its 1 MHz bandwidth, 50 uV offset voltage, and 11 nV/√Hz noise density. The single external gain resistor simplifies adjustment while preserving a broad usable gain range. Input protection can withstand voltages to ±40 V, helping the amplifier tolerate moderate overvoltage conditions. A 2.25 V to 18 V supply range supports both low-voltage and conventional industrial analog systems, while the approximately 3 mA supply-current figure supports low-power instrumentation. The INA114BU uses a versatile three-op-amp instrumentation-amplifier architecture. Its gain is established by the external resistor connected to the gain-setting node, avoiding the need for matched resistor networks. Input and feedback resistors are integrated internally, while the specified input-noise and offset characteristics support accurate extraction of small differential signals. The 1 MHz bandwidth allows the amplifier to process signals beyond static or very-low-frequency measurement tasks while retaining a compact analog implementation. Typical uses include bridge-based pressure and load sensing, biomedical instrumentation, current-shunt measurement, laboratory test equipment, and industrial process-control front ends. The 16-pin SOIC package is useful where moderate pin count, surface-mount assembly, and access to a conventional package are preferred. Its ±40 V input-protection capability is especially relevant when a sensor line can experience transient or sustained voltage excursions. Circuit design should begin with the required gain and bandwidth. Because gain is set by one resistor, verify its noise contribution, tolerance, and stability alongside the sensor source impedance. Keep input and feedback routing short, use a clean low-noise ground reference, and place supply-bypass capacitance close to the device. Check the ±40 V protection rating against the actual maximum input voltage rather than treating it as a substitute for normal operation within the supply range. This product page combines the Texas Instruments INA114 specifications with package information, practical application guidance, drop-in comparison candidates, and design considerations. The comparisons focus on same-package precision instrumentation amplifiers, while the application guidance focuses on practical gain selection, input protection, noise, and layout considerations for measurement circuits.

Запрос цены Контакты
INA115AU - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA115AU

INA115AU - 1MHz Precision Instrumentation Amplifier | Texas Instruments

Texas Instruments INA115AU is a precision instrumentation amplifier with 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input noise, and 3 mA maximum quiescent current, housed in a 16-pin SOIC package. It is designed for low-level differential measurements where small sensor signals must be amplified accurately while rejecting common-mode interference. An instrumentation amplifier is a specialized amplifier category optimized for measuring a differential voltage superimposed on a larger common-mode voltage. Its internal three-op-amp topology provides high input impedance, accurate differential gain, and strong common-mode rejection. Within the broader hierarchy, an instrumentation amplifier is an analog amplifier, an analog integrated circuit, and ultimately a semiconductor designed for precision signal conditioning. The INA115AU combines switched gain operation, low input offset voltage, low drift, and low input bias current. Its specified maximum input offset voltage is 50 µV, maximum offset drift is 0.25 µV/°C, and maximum input bias current is 2 nA. Common-mode rejection reaches 115 dB minimum, while the device accepts input over-voltage protection up to ±40 V. These characteristics make the amplifier suitable for bridge outputs, current-shunt measurements, and low-level sensor interfaces. The wide supply range extends to ±18 V, with operating use supported from ±2.25 V according to the distributor data. Its 1 MHz bandwidth supports faster measurements than a purely high-resolution, slow instrumentation amplifier, while 11 nV/√Hz input noise preserves low-level signal integrity. A 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial, instrumentation, and test-equipment designs. Typical applications include precision bridge amplifiers, strain-gauge monitoring, laboratory sensor interfaces, current-shunt amplifiers, and industrial measurement systems. The switched gain function allows one amplifier to serve multiple sensitivity ranges, although the gain-setting network and feedback resistor accuracy must be checked carefully because they directly influence overall measurement accuracy. Designers should verify input common-mode limits, output swing, gain stability, and supply headroom under the intended load. Input protection improves tolerance to accidental over-voltage, but it does not remove the need for correct polarity, common-mode range, and output-swing analysis. Decoupling should follow the manufacturer datasheet guidance, and sensitive analog traces should be kept away from noisy switching paths. This page combines verified manufacturer highlights, distributor availability information, same-package alternative candidates, application guidance, and design cautions that help engineers move from part selection to a board-level implementation without overlooking the distinctions between instrumentation amplifiers.

Запрос цены Контакты
INA115AU-1 - 1 MHz Precision Instrumentation Amplifier | TI
INA115AU-1

INA115AU-1 - 1 MHz Precision Instrumentation Amplifier | TI

Texas Instruments INA115AU-1 is a precision switched-gain instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 uV input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption. The device is offered in a 16-pin SOIC package and is intended for low-level differential-signal conditioning. An instrumentation amplifier is a specialized analog amplifier that measures the voltage difference between two inputs while rejecting common-mode signals. Its internal three-op-amp architecture provides high input impedance, accurate differential gain, and a defined gain relationship, making it more convenient than a discrete difference amplifier for sensor front ends. Within the broader hierarchy, an instrumentation amplifier is an analog amplifier, a signal-conditioning IC, and part of a measurement and control system. The INA115 family combines precision input offset performance with low input-referred noise and a bandwidth of 1 MHz. Its switched-gain architecture permits gain to be selected through an external resistor connected to the gain-setting pin. The 50 uV offset specification and 11 nV/√Hz noise density are important when resolving millivolt-level or microvolt-level signals, while the 3 mA supply current supports low-power measurement systems. INA115AU-1 operates from dual supplies of ±2.25 V to ±18 V, as identified by Texas Instruments for the INA115AU/1K ordering configuration. The 0.06 V/us slew rate supports accurate settling of larger signal steps. Because the amplifier is designed for differential measurements, input-common-mode range, output swing, and input bias behavior must be checked against the actual signal and supply voltages before the circuit is released for production. Typical uses include bridge-transducer and strain-gauge front ends, precision current measurement, biomedical instrumentation, laboratory measurement equipment, and industrial sensor interfaces. The switched-gain capability simplifies systems in which several gain ranges are required, while the combination of 1 MHz bandwidth, 50 uV offset, and 11 nV/√Hz noise supports accurate signal capture without an unnecessarily high-power amplifier. The principal design consideration is the gain-setting resistor and its associated noise. Use a resistor with suitable low-noise characteristics and keep the gain network close to the gain pin to minimize parasitic capacitance. Input filtering, common-mode rejection, and output settling should be evaluated together because a high-bandwidth amplifier can amplify high-frequency interference as well as the wanted differential signal. This product page combines the exact manufacturer highlights with application guidance, package information, and a practical comparison of documented alternatives. It also highlights the distinction between electrical equivalence and packaging-only ordering codes, helping engineers make a board-level replacement decision without confusing tape-and-reel formats with functional alternatives.

Запрос цены Контакты
INA115AU/1K - 1MHz Precision Instrumentation Amplifier | Texas Instruments
INA115AU/1K

INA115AU/1K - 1MHz Precision Instrumentation Amplifier | Texas Instruments

Texas Instruments INA115AU/1K is a precision, switched-gain instrumentation amplifier with 1 MHz bandwidth, 50 µV maximum input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption. The device is housed in a 16-pin SOIC (DW) package and is intended for low-level differential signal measurement. An instrumentation amplifier is a specialized amplifier category that combines differential input measurement, high input impedance, accurate gain control, and common-mode rejection. Its place in the signal-chain hierarchy is signal conditioning before an ADC, a sensor interface, or a precision measurement system. The INA115 family extends this hierarchy through switched gain selection, allowing one package to support multiple measurement ranges without changing the external feedback network. The primary features of INA115AU/1K include a 1 MHz gain-bandwidth product, 50 µV maximum offset voltage, 11 nV/√Hz input-referred noise, and 3 mA typical power consumption. The 1 MHz bandwidth supports faster settling than many precision instrumentation amplifiers, while the low offset and noise are important when extracting small sensor signals from larger common-mode voltages. Switched gain makes the device practical for systems that must change sensitivity between measurement ranges. The INA115 uses a precision architecture intended to preserve small differential signals in the presence of common-mode voltage and supply variation. Its 16-pin SOIC package provides a conventional surface-mount footprint suitable for industrial and instrumentation equipment. The manufacturer describes the INA115 as a single-channel, switched-gain-enabled precision instrumentation amplifier, with an operating range extending down to ±2.25 V and up to ±18 V according to comparison records for the family. Typical uses include bridge-sensor signal conditioning, biomedical instrumentation, current-shunt measurement, laboratory test equipment, and precision industrial sensor acquisition. The 1 MHz bandwidth is particularly useful when the measurement must be sampled rapidly, while the 11 nV/√Hz noise specification favors low-amplitude signals such as strain-gauge, thermocouple, and resistive-sensor outputs. Layout should treat the input stage as a high-impedance precision analog circuit. Keep input and feedback traces short, place gain-control components away from sensitive input nets, provide local supply bypassing, and avoid routing high-current or switching signals beneath the amplifier pins. Confirm gain, supply, output-swing, and settling requirements against the manufacturer's recommended operating conditions before committing the layout. This product page combines the manufacturer product information, package and ordering data, verified distributor listings, and cross-reference results with application guidance. It also distinguishes true same-package drop-in options from devices that are only functionally similar, helping engineers compare replacement choices without overlooking footprint, gain, noise, or bandwidth constraints.

Запрос цены Контакты
INA115BU - 1MHz Low-Noise INA | Texas Instruments
INA115BU

INA115BU - 1MHz Low-Noise INA | Texas Instruments

Texas Instruments INA115BU is a precision three-op-amp instrumentation amplifier rated for 1 MHz bandwidth, 50 uV maximum offset voltage, 11 nV/sqrt(Hz) input noise, and 3 mA maximum quiescent current. It is supplied in a 16-pin SOIC package and supports supply voltages from 2.25 V to 18 V, allowing operation from low-voltage analog systems through higher-voltage industrial instrumentation. An instrumentation amplifier is a differential analog signal-conditioning IC that amplifies the voltage between two inputs while rejecting common-mode interference. Its internal hierarchy is instrumentation amplifier, differential amplifier, analog amplifier, and semiconductor. The three-op-amp architecture uses resistive feedback to establish gain, high input impedance, and accurate differential gain control. Exposed input-amplifier connections permit switched-gain networks and alternative feedback arrangements. Key performance features include an offset voltage of 50 uV maximum, input voltage drift of 0.25 uV/degree C maximum, input bias current of 2 nA maximum, and common-mode rejection of 115 dB minimum. The device also provides input over-voltage protection to plus or minus 40 V, making it suitable for measurement interfaces where transient or fault conditions may exceed the normal common-mode range. The INA115BU combines 1 MHz bandwidth with 11 nV/sqrt(Hz) noise density. Its slew rate of 0.6 V/us supports accurate reproduction of moderate-frequency waveforms, while the external gain-setting network allows tradeoffs among gain, bandwidth, and noise. The instrumentation-amplifier topology is particularly useful when a low-level sensor differential must be measured in the presence of a larger common-mode voltage. Typical applications include bridge and strain-gauge signal conditioning, precision current measurement, biomedical instrumentation, industrial process-control sensors, and low-level differential data acquisition. The input-overvoltage protection and high common-mode rejection are useful in industrial environments, while low input bias current supports high-impedance sensor interfaces. Designers should place input and feedback resistors close to the device, maintain symmetric input routing, and verify stability with the intended gain network. Gain-setting resistance must also be checked against the required bandwidth, because the effective gain bandwidth relationship becomes increasingly important as closed-loop gain rises. This product summary combines the manufacturer specifications with practical guidance for gain selection, noise analysis, overvoltage protection, and PCB implementation. It also identifies verified nearby instrumentation amplifiers for engineers evaluating replacement or design-comparison requirements.

Запрос цены Контакты
INA115BUG4 - 1MHz Precision Instrumentation Amplifier | TI
INA115BUG4

INA115BUG4 - 1MHz Precision Instrumentation Amplifier | TI

The Texas Instruments INA115BUG4 is a precision instrumentation amplifier with a 1 MHz gain-bandwidth product, 50 µV input offset voltage, 11 nV/√Hz input noise, and 3 mA power consumption, supplied in a 16-pin SOIC package. It is designed for applications requiring accurate differential measurement from low-level sensors and bridge circuits. An instrumentation amplifier is a specialized amplifier that measures the voltage difference between two inputs while rejecting common-mode signals. Its typical signal-chain hierarchy is instrumentation amplifier → differential amplifier → analog amplifier → analog signal-chain IC. By combining high input impedance, precise gain control, and differential input handling, this device reduces the need for separate input amplifiers in sensor-conditioning systems. Key features include the manufacturer-rated 1 MHz bandwidth, 50 µV input offset voltage, and 11 nV/√Hz noise density. The three-op-amp architecture provides gain adjustment flexibility, while the INA115 additionally exposes connections to the input amplifiers, identified as A1 and A2. Those connections support improved gain accuracy at high gain settings and can assist in implementing switched-gain arrangements. The INA115BUG4 supports single-supply operation from 2.25 V to 18 V according to the INA115BU comparison data. Its instrumentation-amplifier architecture is intended for low-level differential signals, but bandwidth and input-voltage limits must be checked at each selected gain. Because this is an analog precision device, careful grounding, reference configuration, resistor selection, and protection design are essential for repeatable results. Typical applications include bridge-based pressure and load-cell measurements, low-voltage sensor front ends, isolated current sensing, biomedical instrumentation, and industrial process monitoring. The 16-pin SOIC package is also practical for conventional surface-mount assembly, although sensitive input routing must be kept away from switching nodes and high-current paths. For a new design, verify the gain-setting resistor values, allowable input common-mode range, supply voltage, output swing, and input protection limits against the manufacturer datasheet for the intended operating condition. Use a clean analog ground reference and place input and gain-setting components close to the device to minimize parasitic errors. This product summary combines the manufacturer’s device description with practical guidance for INA115 pinout verification, gain selection, sensor conditioning, low-noise layout, package compatibility, and drop-in replacement assessment.

Запрос цены Контакты
INA116PA - 3fA Ultra Low Bias Current In-Amp | TI
INA116PA

INA116PA - 3fA Ultra Low Bias Current In-Amp | TI

The Texas Instruments INA116PA is an ultra-low input bias current instrumentation amplifier delivering 3 fA typical input bias current (25 fA at 85C), a 2 mV maximum input offset voltage, and programmable gain from 1 V/V to 1000 V/V in a 16-pin PDIP (N) package rated from -40C to +85C. An instrumentation amplifier is a specialized precision differential amplifier designed to amplify the difference between two input signals while rejecting common-mode voltage. Within the signal-chain hierarchy, it sits above general-purpose op amps in the amplifier family of analog ICs, combining three internal op-amp stages, precision matched resistors, and FET input technology to achieve performance that discrete designs cannot easily match. The headline feature of the INA116 is its Difet (dielectrically isolated FET) input stage with special guarding techniques that yield the 3 fA typical bias current at 25C. Buffered guard drive pins allow the designer to actively drive cable shields and guard rings, reducing leakage paths that would otherwise dominate performance at femtoampere input levels. Input overvoltage protection adds robustness against transient events at the inputs. The classic three-op-amp topology sets gain from 1 to 1000 V/V with a single external resistor, per the manufacturer datasheet. Minimum common-mode rejection is 86 dB, input noise is 28 nV per root hertz at 1 kHz, and quiescent current is only about 1 mA, permitting operation from +/-4.5 V to +/-18 V supplies (9 V to 36 V total). Typical applications include photodiode and ionization chamber front ends, pH and chemical sensor interfaces, electrometer-grade measurement systems, and precision transducer signal conditioning where source impedance is extremely high. Design consideration: at fA-level bias currents, PCB surface leakage dominates system error, so guard rings driven from the buffered guard outputs and careful board cleaning are essential. This page adds value beyond the manufacturer datasheet by synthesizing distributor pricing, drop-in alternative analysis, comparison tables, and practical design guidance in one place.

Запрос цены Контакты