Товары (44.000+)

KSZ8001S-TR - 10/100 Ethernet PHY | Microchip | SSOP-48 (Tape & Reel)
KSZ8001S-TR

KSZ8001S-TR - 10/100 Ethernet PHY | Microchip | SSOP-48 (Tape & Reel)

The Microchip Technology KSZ8001S-TR is a single-chip 10BASE-T, 100BASE-TX, and 100BASE-FX Ethernet physical-layer transceiver with MII, RMII, and SMII host interfaces, a 1.8 V core supply, and 3.3 V analog I/O in a 48-SSOP package. It combines three copper/fiber physical layers with LinkMD cable diagnostics and supports cable lengths up to 130 m on standard Ethernet cabling. An Ethernet physical-layer transceiver, or Ethernet PHY, is the circuit that converts digital Ethernet data into signals suitable for twisted-pair or fiber links and converts received signals back into digital data. In the networking hierarchy, the KSZ8001S-TR sits between a Media Access Controller or Ethernet MAC and its physical medium. Its MII, Reduced MII, and Serial MII interfaces provide host-connection choices for embedded systems, industrial controllers, and networking equipment. Key verified features include 10BASE-T, 100BASE-TX, and 100BASE-FX support, operation from a 1.8 V core, compatibility with 3.3 V signaling, and the three listed host interfaces. The manufacturer literature describes approximately 250 mW power consumption, LinkMD cable-length determination to 200 m with stated accuracy of ±2 m, and robust operation over standard cables longer than 130 m. These characteristics make the device suitable where copper and fiber PHY support share one package. Technically, the transceiver integrates transmit and receive DSP functions needed for Manchester-coded 10 Mb/s Ethernet and MLT-3 100 Mb/s links. Full MII exposes parallel timing and data signals, RMII reduces pin count for higher-throughput controllers, and SMII provides a serial controller option. The serial management interface enables configuration, while LinkMD assists commissioning by estimating cable length and identifying wiring faults rather than requiring every fault to be diagnosed by a higher-level host. Typical uses include industrial Ethernet controllers, embedded gateways, test equipment, print servers, network switches, and optical-to-copper interface equipment. A copper-only design can select 10BASE-T or 100BASE-TX links, while 100BASE-FX support can extend the PHY into fiber-oriented designs. Fiber magnetics, optical signaling requirements, and system timing still need validation against the complete interface design. A key design consideration is that the KSZ8001S-TR needs both its 1.8 V core rail and appropriate 3.3 V analog or digital supplies. Place required bypass capacitors at their pins, route high-speed and analog signals according to the reference layout, and isolate noisy switching nodes from PHY inputs. Check the complete pinout and operating limits in the official KSZ8001L/S datasheet before layout release. This page consolidates verified distributor information, manufacturer technical capabilities, sourcing context, and engineering guidance. It also distinguishes confirmed KSZ8001S-TR facts from values that still require datasheet validation, avoiding unsupported package, pricing, temperature, or replacement claims.

Запрос цены Контакты
KSZ8001SA3 - 10/100 Ethernet Transceiver | Microchip | 48-SSOP
KSZ8001SA3

KSZ8001SA3 - 10/100 Ethernet Transceiver | Microchip | 48-SSOP

The Microchip Technology KSZ8001SA3 is a single-port 10/100 Ethernet transceiver supporting MII, RMII, and SMII interfaces, supplied in a 48-SSOP surface-mount package. Its verified operating range is 0°C to +70°C, and its digital supply accepts either 1.8 V or 3.3 V. The device is intended for embedded systems that require a physical-layer connection to an Ethernet controller or processor MAC. An Ethernet transceiver is an interface integrated circuit that converts logical data into signals suitable for a twisted-pair network and receives those signals in the opposite direction. Within the network hierarchy, the KSZ8001SA3 is an Ethernet interface IC and a physical-layer device. It connects a digital MAC through MII, RMII, or SMII to a 10/100 Ethernet network, while a magnetics-based network interface and appropriate PCB routing complete the physical link. The principal verified features are support for full MII, RMII, and SMII operation, compatibility with 10/100-Mbit Ethernet links, operation from a 1.8 V or 3.3 V supply, and a commercial temperature range of 0°C to +70°C. The 48-SSOP package provides a relatively high pin count for separate data, control, clock, and analog connectivity. That pin count can simplify compatibility with an established 48-pin Ethernet interface layout while still requiring careful signal-integrity and power planning. The KSZ8001SA3 is designed to operate as the physical-layer interface between a network media access controller and the external Ethernet magnetics. MII provides separate transmit and receive data paths, RMII reduces the required interface signals, and SMII provides a serial management-oriented option. Selection among these modes depends on the host controller, clocking scheme, firmware, and PCB layout; the interface mode cannot be changed merely by substituting another package without checking the complete pin-level design. Typical applications include industrial Ethernet control equipment, embedded routers and switches, industrial automation controllers, network-connected test instruments, and embedded systems requiring 10/100-Mbit connectivity. In these systems, the KSZ8001SA3 handles the Ethernet physical layer, while the host processor or dedicated controller handles higher-layer traffic. The device should be paired with a compatible Ethernet controller, network transformer or integrated magnetics, suitable decoupling, and a layout that separates sensitive analog and clock paths from noisy digital circuitry. The primary design consideration is to validate the complete interface rather than relying only on the package name. Confirm the 48-SSOP footprint dimensions, exposed or non-exposed pad arrangement, pin assignments, strap options, clock requirements, and register behavior against the manufacturer documentation before layout release. Maintain short supply paths, place decoupling close to the relevant pins, and use a controlled-impedance layout for the network differential pairs. This page consolidates the verified protocol, package, supply-voltage, and temperature information with practical application guidance and sourcing context. It also identifies the principal verification gaps: current price, detailed electrical limits, lifecycle classification, compliance declarations, and a complete manufacturer-confirmed pin map were not present in the supplied source data and are therefore not guessed.

Запрос цены Контакты
KSZ8001SI - 10/100 Ethernet PHY, 48-SSOP | Microchip
KSZ8001SI

KSZ8001SI - 10/100 Ethernet PHY, 48-SSOP | Microchip

The Microchip Technology KSZ8001SI is a single-chip 10BASE-T, 100BASE-TX, and 100BASE-FX Ethernet physical-layer transceiver with MII, RMII, and SMII host interfaces, supplied in a 48-BSSOP package. It supports 1.8 V CMOS operation, 3.3 V interface operation, 10 Mbit/s and 100 Mbit/s links, and cable diagnostics through LinkMD. An Ethernet PHY is an interface IC that translates between a digital Ethernet Media Independent Interface and analog signaling over twisted-pair or fiber media. In the network hierarchy, the KSZ8001SI sits between a network controller or embedded processor and an Ethernet transformer or optical interface. Its MII support permits a parallel host connection, RMII reduces the host-side pin and signal burden, and SMII provides a serial alternative. The verified device information identifies a 1.8 V CMOS design, 250 mW power consumption, operation over standard cables longer than 130 m, and support for MII, RMII, and SMII. LinkMD determines cable length and diagnoses faulty cables up to 200 m with stated accuracy of ±2 m. These capabilities make the device suitable for embedded Ethernet equipment, industrial controllers, network adapters, and test equipment. The KSZ8001SI supports copper and fiber link modes, including 10BASE-T, 100BASE-TX, and 100BASE-FX. Its 48-BSSOP package is intended for surface-mount PCB assembly, while the supplied search results identify tube packaging for one ordering configuration. The MII, RMII, and SMII interfaces give system designers flexibility in host bus selection and board partitioning. For copper links, the PHY requires appropriate external magnetics, termination, line-side filtering, and a compliant Ethernet transformer or coupling network. For 100BASE-FX, the external fiber interface must be designed for the selected optical device and link budget. The selected interface mode, clocking method, and host voltage must follow the manufacturer datasheet. A critical design consideration is that advertised protocol support does not eliminate the need for PCB-level Ethernet compliance testing. Differential routing, grounding, magnetics placement, isolation boundaries, and power filtering can determine whether a nominal PHY implementation achieves reliable 10BASE-T and 100BASE-TX operation. This page consolidates verified product facts, sourcing data, interface options, and engineering guidance for design evaluation.

Запрос цены Контакты
KSZ8001SL - 10/100 Ethernet PHY, 48-SSOP | Microchip Technology
KSZ8001SL

KSZ8001SL - 10/100 Ethernet PHY, 48-SSOP | Microchip Technology

Microchip Technology KSZ8001SL is a single-chip 10BASE-T, 100BASE-TX, and 100BASE-FX physical-layer transceiver with MII, RMII, and SMII host interfaces, supplied in a 48-lead SSOP package. The verified data identifies 1.8 V and 3.3 V supply operation, a 250 mW power-consumption figure, and support for cables longer than 130 m. It also includes LinkMD cable diagnostics. An Ethernet physical-layer transceiver, or Ethernet PHY, is the interface between a digital host controller and physical copper or fiber media. It belongs to the hierarchy of Ethernet interface ICs, network interface controllers, communication semiconductors, and integrated circuits. By translating host-interface signals into physical-layer signaling, a PHY allows an embedded controller, communications processor, or FPGA to connect to 10 Mb/s or 100 Mb/s Ethernet networks. The KSZ8001SL supports MII, Reduced Media Independent Interface, and Serial Media Independent Interface host connections. This selection of interfaces gives designers options for parallel, reduced-pin, and serial host integration. Its 1.8 V CMOS-oriented implementation and stated 250 mW power consumption are relevant to compact embedded networking equipment where supply efficiency and interface count influence system architecture. The physical-layer capability covers 10BASE-T copper Ethernet, 100BASE-TX twisted-pair Ethernet, and 100BASE-FX fiber Ethernet. Verified manufacturer information identifies LinkMD cable diagnostics, a feature intended to help system software characterize the physical cable connection. Operation over standard cables of more than 130 m is also identified for the device family. Typical uses include industrial Ethernet controllers, embedded network appliances, communications modules, industrial automation equipment, and custom Ethernet designs based on an FPGA or application-specific processor. The MII, RMII, and SMII choices allow the same PHY family to support different host-controller architectures, provided the selected interface is wired and clocked correctly. Designers should preserve the package footprint, supply sequencing, interface timing, and media-side termination requirements of the selected device configuration. Because the verified material does not provide complete pin-level details, current limits, link-time specifications, temperature limits, or validated replacement data, those values should be confirmed in the manufacturer datasheet before schematic release or production qualification. This page consolidates the verified distributor and manufacturer information for KSZ8001SL, distinguishes documented drop-in candidates from unsupported assumptions, and provides application and selection guidance that supplements the basic catalog description without inventing missing electrical or lifecycle details.

Запрос цены Контакты
KSZ8001SL-TR - 10/100 Ethernet PHY, 48-SSOP | Microchip Technology (Tape & Reel)
KSZ8001SL-TR

KSZ8001SL-TR - 10/100 Ethernet PHY, 48-SSOP | Microchip Technology (Tape & Reel)

Microchip Technology KSZ8001SL-TR is a single-chip 10BASE-T, 100BASE-TX, and 100BASE-FX physical-layer transceiver with MII, RMII, and SMII host interfaces, supplied in a 48-lead SSOP package. The verified data identifies 1.8 V and 3.3 V supply operation, a 250 mW power-consumption figure, and support for cables longer than 130 m. It also includes LinkMD cable diagnostics. An Ethernet physical-layer transceiver, or Ethernet PHY, is the interface between a digital host controller and physical copper or fiber media. It belongs to the hierarchy of Ethernet interface ICs, network interface controllers, communication semiconductors, and integrated circuits. By translating host-interface signals into physical-layer signaling, a PHY allows an embedded controller, communications processor, or FPGA to connect to 10 Mb/s or 100 Mb/s Ethernet networks. The KSZ8001SL-TR supports MII, Reduced Media Independent Interface, and Serial Media Independent Interface host connections. This selection of interfaces gives designers options for parallel, reduced-pin, and serial host integration. Its 1.8 V CMOS-oriented implementation and stated 250 mW power consumption are relevant to compact embedded networking equipment where supply efficiency and interface count influence system architecture. The physical-layer capability covers 10BASE-T copper Ethernet, 100BASE-TX twisted-pair Ethernet, and 100BASE-FX fiber Ethernet. Verified manufacturer information identifies LinkMD cable diagnostics, a feature intended to help system software characterize the physical cable connection. Operation over standard cables of more than 130 m is also identified for the device family. Typical uses include industrial Ethernet controllers, embedded network appliances, communications modules, industrial automation equipment, and custom Ethernet designs based on an FPGA or application-specific processor. The MII, RMII, and SMII choices allow the same PHY family to support different host-controller architectures, provided the selected interface is wired and clocked correctly. Designers should preserve the package footprint, supply sequencing, interface timing, and media-side termination requirements of the selected device configuration. Because the verified material does not provide complete pin-level details, current limits, link-time specifications, temperature limits, or validated replacement data, those values should be confirmed in the manufacturer datasheet before schematic release or production qualification. This page consolidates the verified distributor and manufacturer information for KSZ8001SL-TR, distinguishes documented drop-in candidates from unsupported assumptions, and provides application and selection guidance that supplements the basic catalog description without inventing missing electrical or lifecycle details.

Запрос цены Контакты
KSZ8021RNL - 10/100 Ethernet PHY RMII | Microchip
KSZ8021RNL

KSZ8021RNL - 10/100 Ethernet PHY RMII | Microchip

The Microchip Technology KSZ8021RNL is a single-supply 10Base-T/100Base-TX Ethernet physical-layer transceiver with Reduced Media Independent Interface support, a 50 MHz RMII reference-clock input, and a 24-QFN exposed-pad package measuring 4 mm by 4 mm. It provides the physical-layer functions required to connect an RMII-compatible Ethernet MAC or processor to standard Category 5 unshielded twisted-pair cabling. An Ethernet PHY is a semiconductor that converts logical data transmitted by a Media Access Controller into electrical signals suitable for copper cabling, while recovering incoming signals and forwarding recovered data to the MAC. In the product hierarchy, the KSZ8021RNL is an Ethernet transceiver, an interface IC, a physical-layer device, and a network-connectivity semiconductor. Its RMII interface reduces the number of parallel data connections required between the PHY and the host processor compared with older parallel Ethernet interfaces. The manufacturer datasheet identifies the KSZ8021RNL as the variant that accepts a 50 MHz RMII reference clock. It also describes support for status and control registers and an interrupt pin that eliminates the need for the processor to poll PHY output continuously. The 24-QFN exposed-pad construction supports compact Ethernet designs by providing a solderable thermal and electrical connection beneath the package while allowing the board to remove heat through its copper area. The KSZ8021RNL supports both 10Base-T and 100Base-TX operation, allowing a system to use a common physical-layer device for 10 Mbps legacy Ethernet and 100 Mbps Fast Ethernet links. Compatibility with standard CAT-5 unshielded twisted pair makes it applicable to embedded controllers, industrial equipment, access equipment, printers, set-top boxes, and embedded Ethernet systems that use an RMII-capable host processor. Typical implementations place the PHY close to the RJ45 connector and route the differential twisted-pair pairs with controlled geometry. The MAC supplies transmit data and timing signals over RMII, while the PHY translates those signals for the cable. Received data, carrier status, collision information, and interrupt indications are returned to the host through the interface. System firmware then handles link negotiation, autonegotiation, and network-stack configuration. A critical layout consideration is maintaining a continuous ground reference beneath the differential pairs and avoiding splits in the ground plane. The exposed pad should be connected to ground and thermal copper using the manufacturer’s land-pattern guidance. Input and interface traces also require careful return-path planning because the RMII clock and data signals operate at a relatively high digital rate relative to the 10/100 Ethernet data payload. This page combines the manufacturer datasheet, verified distributor identification, package information, and the manufacturer’s hardware-migration guidance. It also distinguishes a genuine same-family drop-in option from newer PHY families whose pin assignments differ, helping engineers avoid replacements that require board changes or interface redesign.

Запрос цены Контакты
KSZ8021RNL-TR - 10/100 Ethernet PHY | Microchip Technology
KSZ8021RNL-TR

KSZ8021RNL-TR - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8021RNL-TR is a single-channel 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with a 3.3 V power supply, reduced MII support, and a 24-QFN exposed-pad package measuring 4 mm by 4 mm. It connects an RMII-compatible Ethernet media access controller to a 10/100 Ethernet network through the physical layer. The KSZ8021RNL-TR version accepts a 50 MHz RMII reference clock, while the related KSZ8031RNL operates with a different reference-clock arrangement. An Ethernet PHY is the physical-layer device in an Ethernet communications hierarchy. It converts logical data and framing signals from a network controller into electrical signaling suitable for twisted-pair cabling, while receiving and decoding incoming signaling. The reduced MII interface reduces the number of signals between the PHY and media access controller, simplifying connections to embedded processors, industrial controllers, and Ethernet switches while supporting 10 Mb/s and 100 Mb/s operation. The device is identified as a one-port transceiver with full RMII support. Its listed operating voltage is 3.3 V, and its 24-pin QFN package includes an exposed pad for board-level thermal dissipation. The manufacturer datasheet also describes an interrupt output that eliminates the need for the processor to poll PHY status registers. These characteristics make the KSZ8021RNL-TR appropriate for compact embedded Ethernet equipment requiring a conventional copper-network physical layer. The KSZ8021RNL-TR is a surface-mount PHY intended for 10BASE-T and 100BASE-TX networks. Its reduced MII connection supports communication with an RMII-compliant MAC, while the interrupt capability can reduce processor polling overhead when link, error, or status events require attention. The 4 mm by 4 mm QFN package supports space-constrained designs, but the exposed thermal pad must be connected according to the manufacturer land-pattern and thermal recommendations. Typical uses include industrial automation equipment, embedded control systems, access-control terminals, test and measurement products, and compact network adapters. The 3.3 V supply and single-channel 10/100 capability are particularly suitable for equipment that does not require multi-gigabit Ethernet. In these systems, the PHY links a 3.3 V RMII-capable controller or processor to a 10/100 Ethernet network while providing status and interrupt handling. PCB design should follow the manufacturer’s recommended component placement, exposed-pad land pattern, and decoupling arrangement. The exposed pad requires an uninterrupted ground connection and adequate thermal-via pattern for reliable heat transfer. Signal routing should also preserve the required separation between Ethernet magnetics and sensitive circuitry, while keeping the 50 MHz RMII reference-clock path short and well controlled. This product record combines the manufacturer data for the KSZ8021RNL and KSZ8031RNL family with package information, sourcing guidance, and design-focused application analysis. It also identifies where detailed clock, register, electrical, and pin-assignment requirements must be confirmed in the manufacturer datasheet before a board is released for production.

Запрос цены Контакты
KSZ8031RNL - 10/100 Ethernet PHY | Microchip Technology
KSZ8031RNL

KSZ8031RNL - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8031RNL is a single-supply 10Base-T/100Base-TX Ethernet physical layer transceiver with a 3.3 V supply, full-duplex operation, and an RMII interface to an Ethernet MAC. It is packaged in a surface-mount 24-QFN (4 x 4 mm) package for compact networking equipment. The device handles transmission and reception over standard CAT-5 unshielded twisted-pair cable. An Ethernet physical layer transceiver is the circuit that converts digital frame data from an Ethernet media access controller into signals suitable for twisted-pair cabling, then converts received cable signals back into digital data. This PHY belongs to the hierarchy Ethernet transceiver > physical layer device > network interface IC > semiconductor. RMII provides a standardized parallel connection between the PHY and a compatible Ethernet processor or switch. The KSZ8031RNL supports both 10Base-T and 100Base-TX operation, allowing one physical-layer design to serve legacy 10 Mb/s and Fast Ethernet 100 Mb/s links. Its full-duplex RMII interface supports simultaneous transmit and receive activity, while single-supply operation simplifies system power design. The 24-QFN package also supports space-constrained embedded networking designs. Compared with the related KSZ8021RNL, the KSZ8031RNL uses the RMII reference-clock arrangement suited to systems requiring a 25 MHz reference. The RMII interface exposes the PHY connections required for data, control, carrier sense, and clock signaling between the transceiver and Ethernet MAC. The manufacturer documentation also identifies the device as a direct-interface physical layer rather than a complete Ethernet controller. Typical uses include industrial Ethernet equipment, embedded control systems, IP cameras, network switches, serial-to-Ethernet products, and compact data-acquisition devices. The device is particularly appropriate when a host processor already includes an RMII-compatible Ethernet MAC and the PCB area is limited. Design the PCB with the 24-QFN footprint, power and decoupling capacitors, a 50 MHz differential clock arrangement, and an RMII interface routed according to the manufacturer datasheet. Confirm PHY address, strap configuration, magnetics, termination, and cable-side layout before releasing the design. This product page combines the manufacturer electrical description, package information, application guidance, replacement cross-checks, and PCB-focused design considerations to support faster component selection and implementation.

Запрос цены Контакты
KSZ8031RNL-TR - 100Mbps Ethernet PHY | Microchip Technology
KSZ8031RNL-TR

KSZ8031RNL-TR - 100Mbps Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8031RNL-TR is a single-supply 10Base-T and 100Base-TX Ethernet physical layer transceiver with a 100 Mbps data rate, a 3.3 V supply, and a 24-QFN 4 mm × 4 mm package. It connects an Ethernet controller or embedded processor to standard CAT-5 unshielded twisted-pair cabling through its RMII or MII interface. An Ethernet PHY is the physical-layer device that converts digital parallel or serial controller traffic into signals suitable for transmission over copper cable. It also receives analog signals from the cable and restores them as digital data. Within the network hierarchy, the KSZ8031RNL-TR sits between an Ethernet MAC or embedded host and the physical network, providing the 10/100 Ethernet link layer interface required for industrial control, embedded networking, and communications equipment. Key features include support for both 10Base-T and 100Base-TX operation, a full RMII interface, compatibility with MII signaling, and a 3.3 V single-supply design. The operating supply range is 3.135 V to 3.465 V, while the stated operating-temperature range is 0°C to +70°C. Its lead-free 24-QFN package supports compact surface-mount layouts in space-constrained embedded systems. The device is designed for single-port 10/100 Ethernet connectivity using standard CAT-5 UTP cable. Its RMII interface provides a comparatively compact connection to a network controller, making it suitable for systems where connector count, board area, and host processor resources must be controlled. MII support expands compatibility with controllers using the parallel Ethernet interface, although final host timing and signaling must follow the manufacturer datasheet. Typical applications include industrial Ethernet equipment, embedded control systems, factory automation interfaces, set-top and communications equipment, and network-connected test instruments. In these systems, the PHY can be placed close to the RJ-45 magnetics, with controlled differential routing between the transceiver and magnetics. A separate Ethernet controller such as the KSZ8001LA3TR can provide the higher-layer MAC functions when the host does not integrate them. Layout quality is critical in an Ethernet design. Place the PHY close to the magnetic component, keep the differential pairs short and impedance-controlled, provide the specified local decoupling, and observe the manufacturer’s component placement and exposed-pad requirements. Verify magnetics selection, termination, isolation, and cable compatibility before production release. This page consolidates the functional characteristics, sourcing information, replacement constraints, and PCB design considerations for engineers evaluating the KSZ8031RNL-TR. It also distinguishes true pin-compatible options from related Ethernet PHYs whose register interfaces or pin assignments require PCB or firmware changes.

Запрос цены Контакты
KSZ8041FTL - 10/100 Ethernet PHY with 100BASE-FX | Microchip
KSZ8041FTL

KSZ8041FTL - 10/100 Ethernet PHY with 100BASE-FX | Microchip

The Microchip Technology KSZ8041FTL is a single-supply 10Base-T, 100Base-TX, and 100Base-FX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, supplied in a 48-pin 7 x 7 mm TQFP package. Its 3.135 V to 3.465 V supply range, one transmitter and one receiver, and automatic MDI/MDI-X handling support copper and fiber Ethernet connectivity. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data from a network controller into electrical or optical-signaling-compatible signals for the physical medium. The KSZ8041 belongs to the Ethernet interface IC hierarchy, combining a 10/100 Ethernet MAC interface with mixed-signal circuitry for 10Base-T, 100Base-TX, and 100Base-FX physical channels. The KSZ8041FTL adds 100Base-FX support to the feature set of the KSZ8041TL. This makes the FTL suitable for fiber links, media converters, and equipment that needs one Ethernet PHY to address copper and fiber interfaces. Automatic crossover handling through HP Auto MDI/MDI-X removes the need to distinguish straight-through and crossover cables in conventional copper installations. Its mixed-signal design is intended to extend signaling distance while reducing power consumption. The device supports full MII, reduced MII, and serial MII connectivity, allowing integration with network controllers operating at different interface rates and pin requirements. The 48-pin lead-free TQFP package provides a conventional surface-mount footprint for industrial and embedded Ethernet equipment. Typical uses include 10/100 industrial Ethernet controllers, fiber-to-copper media converters, embedded gateways, network switches, test equipment, and communication equipment requiring a single PHY with both copper and fiber support. Evaluation is supported by the Microchip KSZ8041FTL-EVAL platform, while the KSZ8041TL-FTL evaluation board covers the related TL and FTL devices. A critical design consideration is validating the selected media mode, PHY address straps, and interface configuration at power-up. The manufacturer hardware design checklist specifically identifies reset-time strap behavior and warns that receive inputs can affect strap latching, so external hardware and software sequencing must follow the manufacturer guidance. This page combines manufacturer-supported interface and package information with distributor availability references, practical application guidance, and engineering-focused comparison data. It also distinguishes exact verified facts from parameters that require confirmation from the current manufacturer datasheet before a new PCB or production release is approved.

Запрос цены Контакты
KSZ8041FTL-S - 10/100 Ethernet PHY | Microchip | 48-TQFP
KSZ8041FTL-S

KSZ8041FTL-S - 10/100 Ethernet PHY | Microchip | 48-TQFP

Microchip Technology KSZ8041FTL-S is a single-supply 10Base-T/100Base-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, packaged in a 48-pin TQFP measuring 7 x 7 mm. It operates from a 3.135 V to 3.465 V supply, supports one transmit and one receive channel, and uses a mixed-signal design intended to extend signaling distance while reducing power consumption. The device also supports HP Auto MDI/MDIX operation. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital frames handled by an Ethernet media-access controller into signals suitable for twisted-pair cabling. It forms the physical-layer element within the broader Ethernet interface hierarchy, which also includes the MAC, clock and timing circuitry, magnetics, connectors, and cable. The KSZ8041 family is intended for embedded systems requiring 10 Mb/s or 100 Mb/s Ethernet connectivity over copper cabling. The KSZ8041 provides MII, RMII, and SMII interfaces, allowing it to connect with controllers operating under different parallel-interface conventions. A single 3.3 V supply reduces the number of external rails required in embedded equipment. Its 48-TQFP package provides enough pins for the Ethernet data interfaces, control signals, clocking connections, physical-layer management functions, and power-ground connections required by the device. The mixed-signal architecture is a central product characteristic. According to the Microchip product page, this design extends signaling distance and reduces power consumption relative to conventional approaches. The PHY supports automatic MDI/MDIX handling through HP Auto MDI/MDIX, simplifying connections to standard Ethernet ports without requiring separate crossover cables in common installations. Typical applications include industrial Ethernet controllers, embedded web servers, set-top equipment, printers, network bridges, industrial automation equipment, and communications modules. The RMII interface is particularly useful where connector count and board area are important, while MII or SMII support provides flexibility for designs using different Ethernet controller architectures. PCB implementation requires close attention to the manufacturer hardware-design checklist, particularly configuration strap values and reset behavior. Strapping pins control speed, duplex, auto-negotiation, power-down functionality, and PHY address, and their levels are latched during power-up and reset. Confirm the required logic levels before finalizing a board because MAC receive signals may influence straps during startup. This product page organizes the electrical characteristics, package information, drop-in family alternatives, application guidance, and design checklist references around the KSZ8041FTL-S. It is intended to accelerate component identification, PCB footprint planning, sourcing, and first-pass feasibility assessment for 10/100 Ethernet designs.

Запрос цены Контакты
KSZ8041FTL-TR - 10/100 Ethernet PHY with 100BASE-FX | Microchip (Tape & Reel)
KSZ8041FTL-TR

KSZ8041FTL-TR - 10/100 Ethernet PHY with 100BASE-FX | Microchip (Tape & Reel)

The Microchip Technology KSZ8041FTL-TR is a single-supply 10Base-T, 100Base-TX, and 100Base-FX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, supplied in a 48-pin 7 x 7 mm TQFP package. Its 3.135 V to 3.465 V supply range, one transmitter and one receiver, and automatic MDI/MDI-X handling support copper and fiber Ethernet connectivity. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data from a network controller into electrical or optical-signaling-compatible signals for the physical medium. The KSZ8041 belongs to the Ethernet interface IC hierarchy, combining a 10/100 Ethernet MAC interface with mixed-signal circuitry for 10Base-T, 100Base-TX, and 100Base-FX physical channels. The KSZ8041FTL-TR adds 100Base-FX support to the feature set of the KSZ8041TL. This makes the FTL suitable for fiber links, media converters, and equipment that needs one Ethernet PHY to address copper and fiber interfaces. Automatic crossover handling through HP Auto MDI/MDI-X removes the need to distinguish straight-through and crossover cables in conventional copper installations. Its mixed-signal design is intended to extend signaling distance while reducing power consumption. The device supports full MII, reduced MII, and serial MII connectivity, allowing integration with network controllers operating at different interface rates and pin requirements. The 48-pin lead-free TQFP package provides a conventional surface-mount footprint for industrial and embedded Ethernet equipment. Typical uses include 10/100 industrial Ethernet controllers, fiber-to-copper media converters, embedded gateways, network switches, test equipment, and communication equipment requiring a single PHY with both copper and fiber support. Evaluation is supported by the Microchip KSZ8041FTL-TR-EVAL platform, while the KSZ8041TL-FTL evaluation board covers the related TL and FTL devices. A critical design consideration is validating the selected media mode, PHY address straps, and interface configuration at power-up. The manufacturer hardware design checklist specifically identifies reset-time strap behavior and warns that receive inputs can affect strap latching, so external hardware and software sequencing must follow the manufacturer guidance. This page combines manufacturer-supported interface and package information with distributor availability references, practical application guidance, and engineering-focused comparison data. It also distinguishes exact verified facts from parameters that require confirmation from the current manufacturer datasheet before a new PCB or production release is approved.

Запрос цены Контакты
KSZ8041FTLI 10/100 Ethernet PHY | Microchip | 48-TQFP
KSZ8041FTLI

KSZ8041FTLI 10/100 Ethernet PHY | Microchip | 48-TQFP

The Microchip Technology KSZ8041FTLI is a single-port 10Base-T/100Base-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, supplied in a 48-pin TQFP package. It is designed for embedded systems that require a 10/100 Ethernet copper connection and a conventional parallel MAC interface. The device uses a single-supply mixed-signal design to extend signaling distance while reducing power consumption, and supports HP Auto-MDI/MDI-X crossover operation. An Ethernet PHY is the physical-layer component that converts digital MAC data into electrical signals for a twisted-pair cable and converts received signals back into digital data for the MAC controller. The KSZ8041 belongs to the Ethernet interface IC hierarchy, where the PHY works alongside a network controller, transformer, RJ45 connector, clock source, and magnetics. Unlike a switch or protocol controller, the KSZ8041 primarily handles analog signaling and line coding at the physical layer. The KSZ8041 supports 10Base-T and 100Base-TX operation and provides MII, RMII, and SMII choices for connection to a host controller. These interface options allow the PHY to be used with controllers having different clocking and data arrangements. The manufacturer describes the device as using a unique mixed-signal design to extend signaling distance while reducing power consumption. HP Auto-MDI/MDI-X support simplifies direct connection to a network transformer without manual crossover configuration. Typical uses include industrial Ethernet equipment, embedded control systems, access equipment, industrial controls, print systems, and embedded network gateways. The 48-TQFP package provides a conventional surface-mount footprint and exposes the PHY, clock, interface, power, and configuration functions needed for implementation in a multilayer PCB. A successful design depends on correct supply decoupling, controlled clocking, proper MII/RMII/SMII connection, and layout that preserves the integrity of the analog receive and transmit paths. The PHY should be placed close to the Ethernet magnetics, with short, controlled-impedance traces for digital interface signals and carefully planned separation between noisy digital return currents and sensitive analog nodes. The manufacturer’s KSZ8041 documentation should be used for the final pin assignments, strap configuration, layout guidance, and interface timing.

Запрос цены Контакты
KSZ8041NLI-TR - 10/100 Ethernet PHY | Microchip
KSZ8041NLI-TR

KSZ8041NLI-TR - 10/100 Ethernet PHY | Microchip

Microchip Technology KSZ8041NLI-TR is a single-supply 10Base-T/100Base-TX Ethernet physical-layer transceiver with MII and RMII interfaces, operating from a single 3.3 V supply and packaged in a 32-QFN 5x5 mm package. It supports one Ethernet channel at 10 Mbps or 100 Mbps and includes the mixed-signal circuitry required to connect a network medium interface to a digital Ethernet controller. An Ethernet PHY, or physical-layer transceiver, converts digital frame data into electrical signaling for a 10/100 Ethernet link and converts received link signals back into data for the host controller. The KSZ8041 sits between an Ethernet MAC or microcontroller with MII/RMII support and the transformer-coupled network interface, providing the physical signaling layer required by IEEE 802.3 Ethernet designs. Key verified features include 10/100Base-TX operation, full MII and RMII interface support, single-supply operation, and a 32-QFN package measuring 5x5 mm. The manufacturer describes a mixed-signal design intended to extend signaling distance while reducing power consumption. The part is identified by the -TR ordering suffix and is listed in tape-and-reel commercial distribution channels. The interface architecture makes the KSZ8041 suitable for embedded Ethernet designs, including industrial controllers, embedded processors, set-top boxes, access equipment, and other systems that require a 10/100 Ethernet physical layer. MII support suits designs requiring separate transmit and receive data paths, while RMII can reduce the number of digital interface signals when supported by the host controller. When placing the device, follow the manufacturer package and land-pattern requirements, provide the specified decoupling and Ethernet magnetics interface components, and route high-speed or high-current network-side connections according to the applicable reference design. The exact pin names, pin functions, electrical limits, and recommended external-component values require confirmation from the official manufacturer datasheet before layout release. This page consolidates verified manufacturer and distributor information for KSZ8041NLI-TR and distinguishes confirmed product facts from parameters that were not included in the supplied search data. It is intended to support component identification, sourcing, and preliminary engineering review rather than replace the complete Microchip datasheet.

Запрос цены Контакты
KSZ8041NLJ-TR 10/100 Ethernet PHY | Microchip | 32-QFN
KSZ8041NLJ-TR

KSZ8041NLJ-TR 10/100 Ethernet PHY | Microchip | 32-QFN

The Microchip Technology KSZ8041NLJ-TR is a single-supply 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, packaged in a 32-pin QFN measuring 5 mm by 5 mm. It operates from a 3.3 V supply and is designed for embedded systems that require 10/100 Mb/s Ethernet connectivity without a separate external MAC. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into signals suitable for a twisted-pair Ethernet cable and converts received cable signals back into digital data. The KSZ8041 belongs to the PHY hierarchy within network interface controllers, interface integrated circuits, and broader communications semiconductors. Its mixed-signal design supports extended signaling distance while reducing power consumption, making it appropriate for industrial, consumer, and embedded Ethernet platforms. The KSZ8041NLJ-TR combines 10BASE-T and 100BASE-TX operation in one device, allowing the same network port to support legacy 10 Mb/s links and Fast Ethernet links. Its MII, RMII, and SMII host interfaces provide flexibility when connecting to a microcontroller, application processor, or dedicated Ethernet controller. Automatic MDI/MDIX handling also helps simplify implementation where either straight-through or crossover cabling may be encountered. The 32-QFN package supports compact, surface-mount PCB construction while providing the exposed thermal-pad area expected for this package family. Its 3.3 V single-supply architecture simplifies power planning in systems that already operate at 3.3 V. The KSZ8041NLJ-TR variant supports an extended temperature range up to 125 °C, making it suitable for industrial and other thermally demanding equipment when the complete system is designed for those conditions. Typical applications include industrial Ethernet controllers, embedded Linux platforms, factory automation equipment, network-connected sensors, set-top boxes, printers, and compact communication modules. The PHY can be used behind a processor with an RMII interface or behind a controller with MII or SMII signaling. Designers must still provide correct magnetic-interface circuitry, decoupling, reference-clock implementation, and PCB routing compliant with the manufacturer’s reference layout. For a new design, use the manufacturer’s recommended Ethernet magnetics, termination, and exposed-pad layout exactly. Keep the digital MII, RMII, or SMII traces away from the analog magnetics interface, provide clean 3.3 V supply routing, and account for the QFN exposed pad in both assembly and thermal planning. This page combines the manufacturer product information, interface and package characteristics, sourcing guidance, drop-in alternatives, comparison parameters, and practical PCB implementation notes to support faster engineering evaluation and component selection.

Запрос цены Контакты
KSZ8041RNL - 10/100BASE-TX RMII PHY | Microchip Technology
KSZ8041RNL

KSZ8041RNL - 10/100BASE-TX RMII PHY | Microchip Technology

The Microchip Technology KSZ8041RNL is a single-supply 10BASE-T/100BASE-TX physical-layer transceiver with a full RMII interface, operating from 3.135 V to 3.465 V in a 32-VFQFN exposed-pad package measuring 5 mm by 5 mm. It accepts a 25 MHz crystal as its input reference clock and supplies a 50 MHz RMII reference clock to the media access controller, eliminating the need for a separate 50 MHz system clock. The device supports one transmit driver and one receive receiver and uses a mixed-signal design intended to extend Ethernet signaling distance while reducing power consumption. An Ethernet PHY is the physical-layer interface between a media access controller and a copper Ethernet network. Within the hierarchy of Ethernet controllers, PHYs, interface transceivers, and semiconductors, the KSZ8041RNL converts digital MAC data into differential 10BASE-T or 100BASE-TX signals and converts received Ethernet signals back into RMII digital data. The RMII interface reduces the number of parallel data signals required between the PHY and MAC while supporting 100 Mb/s operation. The key features include support for both 10BASE-T and 100BASE-TX networks, an RMII-only configuration, a 25 MHz input reference, and a generated 50 MHz RMII reference output. According to the Microchip datasheet 00002245B, the RNL version is an enhanced RMII implementation that does not require a 50 MHz system clock. Microchip also identifies automatic MDI/MDI-X capability in the KSZ8041 product family, reducing the need for manual crossover handling. The mixed-signal architecture separates the digital control and clock paths from the analog line-driver and receive functions. This is important in compact embedded systems because the Ethernet magnetics, crystal, decoupling network, and high-speed digital RMII traces all influence signal integrity. Power-supply noise and imperfect clock routing can therefore affect otherwise correct firmware and media-access-controller configurations. Typical uses include embedded Linux systems, industrial controllers, set-top boxes, access equipment, printers, and embedded network bridges that connect a conventional RMII MAC to a 10/100 Ethernet network. The part can also support a design needing the MAC to receive a stable 50 MHz reference generated by the PHY. The manufacturer product page lists related KSZ8041 variants for MII, SMII, RMII, and fiber support, so interface requirements should be checked before substitution. Designers should provide the specified crystal, clock-support components, Ethernet transformer, decoupling capacitors, and a layout that keeps sensitive analog and differential Ethernet traces isolated from noisy digital circuitry. The power-up strapping pins configure speed, duplex, auto-negotiation, power-down behavior, and PHY address, and their values are latched during reset. The hardware design checklist should be followed because incorrect strap resistors or reset timing can produce an unintended operating mode even when the clock and power rails are correct. This page combines the verified Microchip datasheet details, distributor availability, package information, interface distinctions, and practical migration considerations in a format that helps engineers evaluate the KSZ8041RNL before PCB layout or a second-source decision.

Запрос цены Контакты
KSZ8041RNL-TR - 10/100BASE-TX RMII PHY | Microchip Technology (Tape & Reel)
KSZ8041RNL-TR

KSZ8041RNL-TR - 10/100BASE-TX RMII PHY | Microchip Technology (Tape & Reel)

The Microchip Technology KSZ8041RNL-TR is a single-supply 10BASE-T/100BASE-TX physical-layer transceiver with a full RMII interface, operating from 3.135 V to 3.465 V in a 32-VFQFN exposed-pad package measuring 5 mm by 5 mm. It accepts a 25 MHz crystal as its input reference clock and supplies a 50 MHz RMII reference clock to the media access controller, eliminating the need for a separate 50 MHz system clock. The device supports one transmit driver and one receive receiver and uses a mixed-signal design intended to extend Ethernet signaling distance while reducing power consumption. An Ethernet PHY is the physical-layer interface between a media access controller and a copper Ethernet network. Within the hierarchy of Ethernet controllers, PHYs, interface transceivers, and semiconductors, the KSZ8041RNL-TR converts digital MAC data into differential 10BASE-T or 100BASE-TX signals and converts received Ethernet signals back into RMII digital data. The RMII interface reduces the number of parallel data signals required between the PHY and MAC while supporting 100 Mb/s operation. The key features include support for both 10BASE-T and 100BASE-TX networks, an RMII-only configuration, a 25 MHz input reference, and a generated 50 MHz RMII reference output. According to the Microchip datasheet 00002245B, the RNL version is an enhanced RMII implementation that does not require a 50 MHz system clock. Microchip also identifies automatic MDI/MDI-X capability in the KSZ8041 product family, reducing the need for manual crossover handling. The mixed-signal architecture separates the digital control and clock paths from the analog line-driver and receive functions. This is important in compact embedded systems because the Ethernet magnetics, crystal, decoupling network, and high-speed digital RMII traces all influence signal integrity. Power-supply noise and imperfect clock routing can therefore affect otherwise correct firmware and media-access-controller configurations. Typical uses include embedded Linux systems, industrial controllers, set-top boxes, access equipment, printers, and embedded network bridges that connect a conventional RMII MAC to a 10/100 Ethernet network. The part can also support a design needing the MAC to receive a stable 50 MHz reference generated by the PHY. The manufacturer product page lists related KSZ8041 variants for MII, SMII, RMII, and fiber support, so interface requirements should be checked before substitution. Designers should provide the specified crystal, clock-support components, Ethernet transformer, decoupling capacitors, and a layout that keeps sensitive analog and differential Ethernet traces isolated from noisy digital circuitry. The power-up strapping pins configure speed, duplex, auto-negotiation, power-down behavior, and PHY address, and their values are latched during reset. The hardware design checklist should be followed because incorrect strap resistors or reset timing can produce an unintended operating mode even when the clock and power rails are correct. This page combines the verified Microchip datasheet details, distributor availability, package information, interface distinctions, and practical migration considerations in a format that helps engineers evaluate the KSZ8041RNL-TR before PCB layout or a second-source decision.

Запрос цены Контакты
KSZ8041TL 10/100 Ethernet PHY | Microchip | TQFP-48
KSZ8041TL

KSZ8041TL 10/100 Ethernet PHY | Microchip | TQFP-48

The Microchip Technology KSZ8041TL is a single-supply 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, supplied in a 48-TQFP package. It supports 10 Mb/s and 100 Mb/s copper Ethernet and combines transmit, receive, clock, and management functions for embedded network equipment. The verified manufacturer material identifies a mixed-signal design intended to extend signaling distance while reducing power consumption, plus HP Auto MDI/MDIX capability. An Ethernet physical-layer transceiver, or PHY, converts digital MAC data into signals suitable for twisted-pair cabling and converts received cable signals back into digital data. The KSZ8041 belongs to the Ethernet interface IC hierarchy, connecting a network media-access controller to a 10BASE-T or 100BASE-TX copper link. Its MII, RMII, and SMII support lets designers select an interface appropriate to the host controller and board constraints. The KSZ8041TL provides separate 10BASE-T and 100BASE-TX operation, automatic cable-related handling, and support for HP Auto MDI/MDIX according to the Microchip product page. These features simplify connection to standard Ethernet magnetics and network transformers without requiring a fixed transmit/receive crossover configuration. The verified sources also describe the KSZ8041TL as a low-power physical-layer solution enabled by a mixed-signal architecture. The manufacturer datasheet describes INTRP on pin 32 as an optional interrupt signal for informing an external controller that the PHY register has received a status update. This makes the device suitable for designs requiring PHY-status monitoring alongside packet transmission and reception. The digital host interface can be used with controllers that support MII, RMII, or SMII, subject to the voltage, timing, and pin requirements in the device documentation. Typical uses include industrial Ethernet controllers, embedded gateways, printers, set-top equipment, network interface cards, media-conversion equipment, and industrial control systems. The TL variant is intended for copper-based 10BASE-T/100BASE-TX links; the related KSZ8041FTL adds 100BASE-FX support, so it is not a drop-in functional substitute unless the PCB and magnetics are specifically designed for fiber. For a new layout, follow the manufacturer pinout and reference-circuit recommendations exactly, especially the supply bypass capacitors, crystal or clock network, Ethernet differential pairs, and isolation or magnetics interface. Keep the digital MII/RMII/SMII traces away from the analog magnetics-side circuitry, maintain the specified impedance environment, and provide clean power referenced to the device ground. Confirm the exact package variant, temperature range, and ordering suffix before releasing a PCB.

Запрос цены Контакты
KSZ8041TL-S - 10/100 Ethernet PHY | Microchip Technology
KSZ8041TL-S

KSZ8041TL-S - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8041TL-S is a single-supply 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with one transmitter and one receiver, MII, RMII, and SMII host interfaces, and a 48-lead TQFP package measuring 7 mm by 7 mm. Its 3.135 V to 3.465 V operating-supply range supports 3.3 V network equipment designs. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital frames exchanged with a network controller into electrical signals suitable for twisted-pair cabling. It belongs to the interface-IC hierarchy: Ethernet PHY, network interface, interface IC, and semiconductor. The KSZ8041 family supports both 10BASE-T and 100BASE-TX copper links and provides configurable host-facing interfaces for integration with Ethernet MAC controllers. The KSZ8041TL-S uses a mixed-signal design intended to extend Ethernet signaling distance while reducing power consumption. Its one-driver, one-receiver arrangement supports bidirectional copper communication through an external magnetics-based network interface. The part provides MII, RMII, and SMII connectivity, allowing system designers to select an interface appropriate to MAC timing and board constraints rather than introducing a separate PHY for each parallel-interface mode. The principal operating constraints center on the single 3.3 V supply, supported Ethernet data rates, copper media support, package footprint, and configuration straps. The device supports 10BASE-T and 100BASE-TX operation but does not include the 100BASE-FX capability described for the KSZ8041FTL family member. The target therefore fits copper Ethernet designs requiring MII, RMII, or SMII connectivity rather than fiber-media converter designs. Typical uses include industrial Ethernet controllers, embedded network equipment, print servers, network interface adapters, and communication equipment that connects a host MAC to a 10/100 copper Ethernet network. Its SMII interface can also suit designs requiring a wider parallel data bus, while RMII reduces the number of host-side signals when board area is more constrained than throughput demands. When designing a board around the KSZ8041TL-S, follow the manufacturer hardware design checklist for power sequencing, reset behavior, PHY strapping, magnetic-component selection, and magnetics-side layout. Ensure the host interface voltage levels match the selected MII, RMII, or SMII mode, and avoid driving strap pins with external circuitry that could interfere with startup sampling. This page consolidates the KSZ8041TL-S electrical identity, package details, host-interface options, sourcing guidance, drop-in candidates, and practical PCB considerations into one engineering reference. It also distinguishes the target from copper-only, industrial-temperature, and fiber-capable members of the KSZ8041 family.

Запрос цены Контакты
KSZ8041TL-TR 10/100 Ethernet PHY | Microchip | TQFP-48 (Tape & Reel)
KSZ8041TL-TR

KSZ8041TL-TR 10/100 Ethernet PHY | Microchip | TQFP-48 (Tape & Reel)

The Microchip Technology KSZ8041TL-TR is a single-supply 10BASE-T/100BASE-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, supplied in a 48-TQFP package. It supports 10 Mb/s and 100 Mb/s copper Ethernet and combines transmit, receive, clock, and management functions for embedded network equipment. The verified manufacturer material identifies a mixed-signal design intended to extend signaling distance while reducing power consumption, plus HP Auto MDI/MDIX capability. An Ethernet physical-layer transceiver, or PHY, converts digital MAC data into signals suitable for twisted-pair cabling and converts received cable signals back into digital data. The KSZ8041 belongs to the Ethernet interface IC hierarchy, connecting a network media-access controller to a 10BASE-T or 100BASE-TX copper link. Its MII, RMII, and SMII support lets designers select an interface appropriate to the host controller and board constraints. The KSZ8041TL-TR provides separate 10BASE-T and 100BASE-TX operation, automatic cable-related handling, and support for HP Auto MDI/MDIX according to the Microchip product page. These features simplify connection to standard Ethernet magnetics and network transformers without requiring a fixed transmit/receive crossover configuration. The verified sources also describe the KSZ8041TL-TR as a low-power physical-layer solution enabled by a mixed-signal architecture. The manufacturer datasheet describes INTRP on pin 32 as an optional interrupt signal for informing an external controller that the PHY register has received a status update. This makes the device suitable for designs requiring PHY-status monitoring alongside packet transmission and reception. The digital host interface can be used with controllers that support MII, RMII, or SMII, subject to the voltage, timing, and pin requirements in the device documentation. Typical uses include industrial Ethernet controllers, embedded gateways, printers, set-top equipment, network interface cards, media-conversion equipment, and industrial control systems. The TL variant is intended for copper-based 10BASE-T/100BASE-TX links; the related KSZ8041FTL adds 100BASE-FX support, so it is not a drop-in functional substitute unless the PCB and magnetics are specifically designed for fiber. For a new layout, follow the manufacturer pinout and reference-circuit recommendations exactly, especially the supply bypass capacitors, crystal or clock network, Ethernet differential pairs, and isolation or magnetics interface. Keep the digital MII/RMII/SMII traces away from the analog magnetics-side circuitry, maintain the specified impedance environment, and provide clean power referenced to the device ground. Confirm the exact package variant, temperature range, and ordering suffix before releasing a PCB.

Запрос цены Контакты
KSZ8041TLI - 10/100 Ethernet PHY | Microchip Technology
KSZ8041TLI

KSZ8041TLI - 10/100 Ethernet PHY | Microchip Technology

The Microchip Technology KSZ8041TLI is a single-channel 10Base-T/100Base-TX Ethernet physical-layer transceiver with full MII, RMII, and SMII interfaces, supplied in a 48-pin TQFP package. The device operates from a single 3.3 V supply and supports IEEE 802.3 and IEEE 802.3u Ethernet operation at 10 Mbps and 100 Mbps. Its integrated mixed-signal design is intended to extend signaling distance while reducing power consumption in compact embedded networking equipment. An Ethernet PHY is the physical-layer component that converts digital data from a MAC or Ethernet controller into analog signaling for a copper network, while receiving and converting incoming signals back into digital data. In the broader hierarchy, the KSZ8041TLI is an Ethernet interface transceiver, a network interface IC, and a semiconductor for Ethernet connectivity. It is appropriate for industrial control, embedded systems, communications equipment, and other designs requiring a dedicated 10/100 Ethernet front end. The verified device information identifies support for auto-negotiation through hardware pin strapping on pin 42 or software using register 0h bit 12. Auto-negotiation follows Clause 28 of the IEEE 802.3u specification and allows link partners to select the highest common operating mode. The same 48-pin TQFP package also supports MII, RMII, and SMII host interfaces, allowing designers to match the PHY to different MAC architectures. The KSZ8041TLI is designed for surface-mount implementation and uses a 3.3 V single-supply architecture. Its mixed-signal approach supports the 10Base-T and 100Base-TX physical layers while controlling power use compared with discrete implementations. The product page also identifies HP Auto MDI/MDIX support, which simplifies connection to both straight-through and crossover cable arrangements in many network designs. Typical uses include embedded Ethernet controllers, industrial automation modules, serial-to-Ethernet equipment, printer controllers, set-top boxes, and communication appliances. When designing around this PHY, verify the exact MAC interface mode, pin strapping requirements, magnetics selection, and termination network against the manufacturer datasheet. The verified data confirms the functional family and package but does not provide a complete pin list, recommended magnetics part numbers, or detailed timing values. This product record combines verified distributor and manufacturer information with practical interface-selection guidance, same-package alternatives, pricing context, and design cautions. The comparison and notes help distinguish temperature, packaging, and interface-option differences without treating functionally similar parts as automatically drop-in replacements.

USD $3,61 В наличии
KSZ8041TLI-S - 10/100 Ethernet PHY | Microchip | TQFP-48
KSZ8041TLI-S

KSZ8041TLI-S - 10/100 Ethernet PHY | Microchip | TQFP-48

The Microchip Technology KSZ8041TLI-S is a single-supply 10BASE-T and 100BASE-TX Ethernet physical-layer transceiver with MII, RMII, and SMII interfaces, packaged in a 48-pin TQFP measuring 7 x 7 mm. It supports 10 Mb/s and 100 Mb/s Ethernet connectivity and incorporates automatic MDI/MDI-X handling for link partner compatibility. An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into the electrical signaling used by 10BASE-T and 100BASE-TX networks. It belongs to the network interface controller and Ethernet transceiver hierarchy, operating between a network media-access controller and the transformer-coupled Ethernet line. The KSZ8041 supports MII, RMII, and SMII host interfaces, allowing integration with controllers operating in parallel, reduced-pin, or source-synchronous signaling configurations. The principal benefits of the KSZ8041TLI-S are its 10/100 Mb/s dual-rate support, three digital host-interface choices, single-supply operation, and mixed-signal design. The manufacturer describes the mixed-signal implementation as extending signaling distance while reducing power consumption. Automatic MDI/MDI-X support also removes the need to configure transmit and receive pairs manually when either straight-through or crossover cabling is used. The device integrates the analog PHY circuitry and digital host-interface functions required for a compact Ethernet front end. Its 48-pin TQFP-48 package provides separate interface and power-related connections on a conventional surface-mount footprint. Because it is a single transceiver, it does not by itself provide two independent copper ports, multi-port switching, or packet processing. Those functions belong to the network controller, switch, or higher-level system around the PHY. Typical uses include embedded control systems, industrial automation equipment, communications modules, print systems, and compact network interfaces that require 10BASE-T or 100BASE-TX connectivity. The MII interface supports designs with a broad parallel signal set, RMII reduces host-side pin requirements, and SMII supports systems configured for source-synchronous signaling. Selection should account for the host controller's supported physical interface and the electrical requirements of the magnetic network interface. Place the PHY, its supporting passive components, and the Ethernet magnetic device according to the manufacturer's reference layout. Keep high-speed host-interface traces short and controlled, provide the specified supply and decoupling arrangement, and account for magnetics and connector placement when defining the Ethernet channel. Verify signal integrity, return loss, insertion loss, and radiated emissions over the intended network interface before production release. This page organizes the official product information, package details, replacement comparisons, interface selection guidance, and practical integration notes into one engineering-focused resource. It also distinguishes confirmed drop-in options from functional alternatives so that footprint, interface, and parameter compatibility can be checked before a PCB substitution is approved.

Запрос цены Контакты
KSZ8041TLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)
KSZ8041TLI-TR

KSZ8041TLI-TR - 10/100 Ethernet PHY | Microchip Technology (Tape & Reel)

The Microchip Technology KSZ8041TLI-TR is a single-channel 10Base-T/100Base-TX Ethernet physical-layer transceiver with full MII, RMII, and SMII interfaces, supplied in a 48-pin TQFP package. The device operates from a single 3.3 V supply and supports IEEE 802.3 and IEEE 802.3u Ethernet operation at 10 Mbps and 100 Mbps. Its integrated mixed-signal design is intended to extend signaling distance while reducing power consumption in compact embedded networking equipment. An Ethernet PHY is the physical-layer component that converts digital data from a MAC or Ethernet controller into analog signaling for a copper network, while receiving and converting incoming signals back into digital data. In the broader hierarchy, the KSZ8041TLI-TR is an Ethernet interface transceiver, a network interface IC, and a semiconductor for Ethernet connectivity. It is appropriate for industrial control, embedded systems, communications equipment, and other designs requiring a dedicated 10/100 Ethernet front end. The verified device information identifies support for auto-negotiation through hardware pin strapping on pin 42 or software using register 0h bit 12. Auto-negotiation follows Clause 28 of the IEEE 802.3u specification and allows link partners to select the highest common operating mode. The same 48-pin TQFP package also supports MII, RMII, and SMII host interfaces, allowing designers to match the PHY to different MAC architectures. The KSZ8041TLI-TR is designed for surface-mount implementation and uses a 3.3 V single-supply architecture. Its mixed-signal approach supports the 10Base-T and 100Base-TX physical layers while controlling power use compared with discrete implementations. The product page also identifies HP Auto MDI/MDIX support, which simplifies connection to both straight-through and crossover cable arrangements in many network designs. Typical uses include embedded Ethernet controllers, industrial automation modules, serial-to-Ethernet equipment, printer controllers, set-top boxes, and communication appliances. When designing around this PHY, verify the exact MAC interface mode, pin strapping requirements, magnetics selection, and termination network against the manufacturer datasheet. The verified data confirms the functional family and package but does not provide a complete pin list, recommended magnetics part numbers, or detailed timing values. This product record combines verified distributor and manufacturer information with practical interface-selection guidance, same-package alternatives, pricing context, and design cautions. The comparison and notes help distinguish temperature, packaging, and interface-option differences without treating functionally similar parts as automatically drop-in replacements.

USD $3,61 В наличии
KSZ8051MLL - 100Mbps MII Ethernet PHY | Microchip Technology
KSZ8051MLL

KSZ8051MLL - 100Mbps MII Ethernet PHY | Microchip Technology

Microchip Technology KSZ8051MLL is a single-supply 10Base-T/100Base-TX Ethernet physical-layer transceiver with full MII support, 100 Mbps data rate, and a 48-LQFP 7 x 7 mm package. It operates from a 3.3 V supply with a specified 3.135 V to 3.465 V range and is designed for transmission and reception over standard Category 5 unshielded twisted-pair cable. An Ethernet physical-layer transceiver, or PHY, converts logical data transmitted by a MAC or controller into signals suitable for copper Ethernet wiring and converts received cable signals back into digital data. The KSZ8051MLL belongs to the 10/100 Ethernet PHY category, within interface ICs and the broader Ethernet communications hierarchy. Its full MII interface provides parallel control, data, and status connections to a network controller. The principal operating characteristics are a 100 Mbps maximum data rate, one transmitter and one receiver, and a 3.3 V supply. Manufacturer information identifies support for 1.8 V, 2.5 V, and 3.3 V interface operating levels, depending on the configuration and connected controller. The commercial-temperature version operates from 0°C to +70°C and is supplied in a surface-mount 48-LQFP package. The integrated PHY reduces the amount of external circuitry required for a 10/100 Ethernet endpoint. It handles physical signaling to the network medium while the associated controller manages packet processing and the higher-level protocol stack. Full MII support makes it appropriate for designs that require a conventional parallel Ethernet interface rather than a serial reduced-media interface. Typical applications include industrial Ethernet equipment, embedded network controllers, print servers, IP cameras, building-control gateways, and compact communication modules. The 100 Mbps rate supports Fast Ethernet networks, while MII connectivity allows direct integration with controllers such as LAN9353T/PT and related Ethernet interface devices. PCB implementation requires careful separation between the digital MII signals and the analog magnetics interface. Place network-side filtering and magnetics close to the connector, observe the recommended copper and layout practices in the manufacturer datasheet, and keep high-current and high-speed return paths controlled to reduce radiated emissions and susceptibility to external noise. This page combines the manufacturer product information, interface characteristics, package details, drop-in candidates, and practical Ethernet design guidance. It is intended to help engineers verify mechanical compatibility, MII requirements, supply conditions, and thermal constraints before integrating the KSZ8051MLL into a Fast Ethernet design.

Запрос цены Контакты