Интегральные схемы

MC3488AP1

MC3488AP1 Dual EIA-423/EIA-232D Line Driver | onsemi

The onsemi MC3488AP1 is a dual single-ended line driver designed for EIA-423, EIA-232D, CCITT X.26, X.28, and Federal Standard FIDS1030 signal-interface requirements. The device is packaged in an 8-lead PDIP and provides two driver channels for converting logic-level signals into balanced or unbalanced communication-line waveforms. Its architecture is intended for point-to-point data transmission systems where controlled slew rate, signal shaping, and standard-compliant line levels are important. The MC3488AP1 belongs to the interface IC hierarchy, which includes line drivers, line receivers, RS-232 transceivers, RS-422/RS-485 interface devices, and broader communication ICs. A line driver strengthens a digital signal before it travels through a cable, allowing the signal to retain useful amplitude and timing characteristics over the interconnect. The MC3488A is particularly relevant when an interface must satisfy legacy EIA-423 or EIA-232D signaling requirements rather than only modern logic-level communication. The dual-channel arrangement allows one package to drive two independent communications lines, reducing component count and simplifying board layout compared with separate single-channel drivers. The DIP-8 package supports through-hole assembly and is useful in legacy industrial, telecommunications, instrumentation, and data-communication equipment where component availability, serviceability, and socketed assembly remain important. The manufacturer's MC3488A documentation identifies the device as a dual line driver with externally controlled wave-shaping and slew-rate behavior. Typical applications include legacy data terminals, industrial control links, serial-interface adapters, telecommunications equipment, and embedded systems that need an RS-232D or EIA-423-compatible output stage. The driver should be used with the correct termination, biasing, protection, and cable-routing practices for the selected communication standard. The MC3488AP1 does not include a receiver in the same package, so a separate receiver or transceiver may be required for bidirectional links. When designing a replacement board, verify the exact pinout, supply voltage, output levels, propagation delay, slew rate, and enable or shutdown behavior against the manufacturer datasheet. A nominally similar line-driver package is not automatically a drop-in replacement because EIA-423 and EIA-232D implementations can differ in reference-ground handling, output impedance, and timing. This page combines the manufacturer-aligned part identity, source links, and engineering guidance to support component selection and board-level validation.

Запрос цены Контакты

MC44BS373CAD

MC44BS373CAD - PLL-Tuned UHF/VHF Audio/Video Modulator | NXP

The NXP MC44BS373CAD is a PLL-tuned UHF and VHF audio/video high-integration CMOS modulator designed for VCRs, set-top boxes, and similar consumer video appliances. It supports multiple television standards including NTSC and PAL, integrates a programmable RF output stage, and is controlled via a 5 V- and 3.3 V-compatible I2C bus. The device is supplied in a 16-pin SOIC (SO16NB) small-outline package with gull-wing leads. A modulator (in this context, an RF modulator) is a transmitter IC that mixes a baseband audio and composite-video signal up to a UHF or VHF carrier suitable for direct injection into the antenna input of an analog television receiver. RF modulators sit between the source device (VCR, set-top box, DVD player) and the TV, and historically they were implemented as discrete mixer/oscillator chains. The MC44BS373CA family replaced that discrete chain with a fully integrated PLL-synthesized modulator, dropping dozens of components into a single 16-pin SOIC. Within the broader taxonomy, this part is an RF IC -> modulator -> consumer video IC -> semiconductor. Key specifications include a typical TV output level of 82 dBuV at the antenna terminal, I2C control at standard-mode 100 kHz or fast-mode 400 kHz, multi-standard support (B/G, D/K, M/N, L), and a single 5 V supply. The PLL is fully programmable via the serial interface, removing the manual channel-adjustment trimmers that legacy designs required. A bypass mode supports test and modulation-disabled conditions for factory alignment. Architecturally, the MC44BS373CA uses an on-chip PLL frequency synthesizer driven by an external reference resonator, a programmable divider, and a double-balanced mixer that combines the modulated audio subcarrier with the composite video baseband. The result is a low-phase-noise carrier that meets ETSI EN 50083-13 and FCC Part 15 emission masks for consumer TV modulator products. Compared with the legacy MC44BS373/4 family, the MC44BS373CA revision lowers power consumption and provides finer carrier frequency step resolution. Typical applications include VCR RF output stages, satellite and terrestrial set-top box modulators, DVD player composite-to-RF conversion, game consoles, and CCTV/security observation systems that need to feed analog TV monitors. The wide standard coverage allows a single BOM to ship into multiple regional markets, simplifying manufacturing. Designers should note that the part requires a 75 ohm output network and proper shielding to meet conducted and radiated emissions limits. The external reference resonator value determines the carrier frequency step, and any drift in this component directly translates into channel offset on the TV. This page synthesizes distributor pricing, drop-in alternatives, application circuits, and practical design notes not found in the standalone datasheet.

Запрос цены Контакты

MC44BS373CAEF

MC44BS373CAEF - NTSC/PAL Audio/Video RF Modulator | NXP SOIC-16

The NXP (formerly Motorola/Freescale) MC44BS373CAEF is a CMOS audio/video RF modulator IC housed in a 16-pin SOIC package, designed for VCRs, set-top boxes, and similar consumer audio/video devices. The part supports multiple broadcast standards (NTSC and PAL) and integrates a TV output driver delivering approximately 82 dBuV at the antenna output. It provides a 5 V and 3.3 V compatible I2C bus interface for register programming, enabling flexible configuration of video modulation, audio FM subcarrier, and output channel selection without external mechanical tuning components. A modulator is the final analog stage of a baseband audio/video chain: it translates a composite baseband video signal and an audio subcarrier up to a select UHF/VHF RF channel suitable for direct connection to a television antenna input. Inside this product family (MC44BS373/4 and the newer MC44CC373/4 generation), the modulator replaces discrete RF upconverter designs with a small, programmable silicon block, saving board area and reducing assembly cost. The device sits at the boundary between analog baseband ICs and the antenna/RF domain, so engineers typically consider it as a "system" component rather than a generic op-amp or logic IC. Key features include multi-standard video modulation (B/G/I/D/K/L depending on firmware settings), an on-chip audio FM modulator at 4.5 MHz, 5.5 MHz, or 6.0 MHz subcarrier frequencies, I2C control up to 400 kHz, low power consumption on a single 5 V supply, and integrated RF output stage with selectable gain. A flexible test/calibration mode is also exposed through the I2C registers to support factory alignment procedures. The CMOS process allows the entire modulator to operate from a single supply rail while keeping heat dissipation minimal for set-top and DVD recorder applications. Typical applications include VCR RF output stages, set-top box down-stream modulators, DVD recorder modulators, PC TV tuner cards, and video game consoles that need to feed an analog TV. The I2C interface also makes this modulator attractive for factory-aligned consumer electronics where channel alignment and audio deviation must be set without mechanical adjustment.

Запрос цены Контакты

MC44BS373CAFC

MC44BS373CAFC - NTSC/PAL Audio/Video RF Modulator IC | NXP

The NXP MC44BS373CAFC is a CMOS audio/video RF modulator IC for VCR, set-top box, and similar consumer video appliances, supporting multiple standards including NTSC and PAL outputs. It integrates a programmable RF output stage with typical TV output level of 82 dBµV, audio subcarrier mixing, and a 5 V / 3.3 V compatible I²C bus for control, all housed in a 20-pin HVQCCN (5x5 mm QFN-style) package. Key specifications include TV output level 82 dBµV typical, an integrated I²C slave interface compatible with both 5 V and 3.3 V microcontrollers, and CMOS process technology for reduced power consumption. The MC44BS373CAFC belongs to the legacy MC44BS373/4 family, succeeded by the MC44CC373/4 generation of RF modulators. The IC accepts baseband audio and video inputs and upconverts them to standard TV RF channels for connection to legacy television receivers. The device uses a programmable architecture where the I²C interface configures RF channel selection, audio modulation mode (mono, BTSC, A2), video modulation depth, and RF output level. An internal PLL synthesizer locks to the selected output channel, eliminating external tank circuits. The 20-pin QFN-style package minimizes PCB area while providing adequate thermal dissipation for set-top box duty cycles. Typical applications include VCRs, set-top boxes, DVD recorders, satellite receivers, and security/CCTV equipment with RF output to analog televisions. The audio subcarrier generator supports multiple broadcast standards, allowing the same hardware platform to be configured for NTSC-M, PAL-B/G, PAL-D, and PAL-I markets via firmware. Compared to discrete modulator designs using separate video amplifier and RF mixer stages, the MC44BS373CAFC reduces BOM count by 20+ components. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet. The MC44BS373CAFC represents one of the final-generation single-chip consumer RF modulators before the industry transitioned to digital HDMI outputs.

Запрос цены Контакты

MC44BS374T1AEF

MC44BS374T1AEF - PLL-Tuned UHF/VHF A/V Modulator | NXP

The NXP MC44BS374T1AEF is a PLL-tuned UHF and VHF audio/video high-integration CMOS RF modulator housed in a 16-pin SOIC (Small Outline IC) package. It is a member of the MC44BS373/4 family of legacy modulators and targets NTSC and PAL television output applications such as set-top boxes, DVD players, VCRs, and video surveillance encoders. The modulator integrates a phase-locked loop (PLL) frequency synthesizer, video modulator, audio FM modulator, and I2C-compatible control interface in a single CMOS die. An RF modulator is a transmitter IC that converts a baseband audio and video signal into a vestigial-sideband or double-sideband RF carrier suitable for connection to a television's antenna input. Within the broader product hierarchy, the MC44BS374 sits at: modulator -> RF transmitter -> specialized consumer IC -> integrated circuit -> semiconductor. It is the direct descendant of the legacy MC44BS373/4 family and is functionally superseded by the newer MC44CC373/MC44CC374 CMOS family while retaining the same footprint and electrical interface to ease migration. Key features include programmable UHF/VHF output frequency via the high-speed I2C-compatible bus, a Logic Output Port pin (pin 3) for status or switching functions, 5 V and 3.3 V compatible I2C logic levels, and a TV output level of 82 dBuV (typical, MC44BS374T1A variant) or 75 dBuV (MC44BS374T1 variant). The PLL architecture provides fine channel selection across the broadcast TV band, allowing the modulator to replace traditional saw filters and discrete modulator circuits in cost-sensitive consumer designs. The IC uses a CMOS process with an integrated VCO and PLL loop filter, reducing external component count compared with older bipolar modulator designs. Typical DC supply is 5 V, and the high-speed I2C bus allows full register configuration of audio deviation, video modulation depth, RF output frequency, and power-down mode. The 16-SOIC package is industry-standard and footprint-compatible with the newer MC44CC374 family, simplifying in-place upgrades. Typical applications include set-top box RF outputs, DVD/VCR combo outputs to legacy televisions, video game console A/V-to-RF adapters, security camera RF modulators, and PC TV-capture cards. The Logic Output Port pin can be used to drive an external LED indicator or switch a relay on channel change. The combination of low external parts count and I2C programmability makes this part attractive for high-volume consumer products. When designing with this modulator, pay close attention to the RF output network - use a proper 75 ohm matching network and shielding to meet FCC/CE radiated emissions limits. Decouple VCC with a 10 uF bulk and 100 nF ceramic capacitor placed as close to the IC as possible; inadequate bypassing produces visible hum bars on the modulated video output. This page synthesizes distributor pricing, drop-in alternatives from the same NXP family (MC44BS373T1AEF, MC44CC373T1AEF, MC44CC374T1AEF), and practical design notes that are not aggregated on DigiKey, Mouser, or Octopart product pages.

Запрос цены Контакты

MC44BS374T1EFR2

MC44BS374T1EFR2 - PLL UHF/VHF A/V Modulator, 16-SOIC | NXP

The NXP MC44BS374T1EFR2 is a PLL-tuned UHF and VHF audio/video high-integration modulator housed in a 16-pin SOIC package, supporting both NTSC and PAL broadcast standards. It delivers synthesized RF output across the UHF/VHF bands from a single 5 V supply and integrates the sound subcarrier oscillator, video modulator, and RF upconverter into a single CMOS die. A video modulator is a specialized IC that mixes a baseband composite video signal (with audio subcarrier) up to a channel-frequency RF output suitable for connection to an antenna input of a TV or set-top box. It belongs to the hierarchy of specialized ICs -> interface ICs -> RF/IF signal chain ICs, and historically served consumer video appliances (VCRs, set-top boxes, DVD recorders, video game consoles) before HDMI replaced analog RF distribution. Key features include a wideband PLL allowing flexible channel selection by I2C programming, low intermodulation distortion for clean video reproduction, separate audio and video inputs, and an integrated DC-DC-friendly architecture that minimizes external component count. The device supports both B/G and D/K system variants in the MC44BS374T1/374T1A family and is footprint-compatible with the earlier MC44BC374T1 generation. From an architectural standpoint, the IC uses a fractional-N PLL synthesizer referenced to a low-phase-noise crystal, allowing fine channel resolution while keeping spurious content low. The modulator chain runs at low power and the RF output stage drives 75 ohm loads with a typical output level in the 70-80 dBuV range, suitable for direct connection to receiver antenna inputs. Typical applications include analog-channel output for legacy TVs in set-top boxes, RF modulation for surveillance camera baseband-to-coax distribution, and modulator modules in VCR/DVD-R designs that must output to older receivers without HDMI inputs. When designing with this device, observe the decoupling requirements from the manufacturer datasheet - typically a 100 nF ceramic on each supply pin plus a bulk 10 uF capacitor at the modulator supply input - and route the RF output trace with controlled 75 ohm impedance for clean spectral output. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, helping engineers sourcing or evaluating the MC44BS374T1EFR2 make confident second-source decisions.

Запрос цены Контакты

MC4558CP1

MC4558CP1 - Dual 2.5MHz Wide-Bandwidth Op-Amp DIP-8 | onsemi

The onsemi MC4558CP1 is a monolithic dual wide-bandwidth operational amplifier housed in an 8-pin PDIP (DIP-8) through-hole package, internally compensated and pin-compatible with the industry-standard 1458/4558 pinout. According to the onsemi datasheet, each of the two on-chip amplifiers delivers a unity-gain bandwidth of 2.5 MHz (C-grade) and 2.0 MHz (AC-grade), with the MC4558AC variant specifically guaranteed to the 2.5 MHz figure. The device targets cost-sensitive general-purpose analog signal-conditioning roles that benefit from higher small-signal bandwidth than the legacy 1458 family. What is an operational amplifier (op-amp)? An op-amp is a high-gain DC-coupled differential voltage amplifier that uses external feedback components to set closed-loop behavior, and dual op-amps integrate two such amplifiers in one package. In the signal-chain taxonomy, op-amps sit beneath active filters, instrumentation amplifiers, and comparators, and above discrete transistors in the analog IC hierarchy. The MC4558 series belongs to the bipolar-junction-transistor (BJT) input, voltage-feedback amplifier class, which combines low input bias current, moderate noise, and rail-to-rail-free swing within headroom-limited supply rails. Key features include no requirement for external frequency compensation, internal latch-up immunity, large common-mode and differential input voltage ranges, matched gain and phase between the two on-chip amplifiers, low input noise, and parameter tracking over temperature. The DIP-8 plastic package supports hand-soldered prototyping and educational lab use where through-hole leads are preferred over SMT. Operating supply is typically ±15 V dual or +30 V single-ended, and the part is specified for the commercial 0 °C to +70 °C range on the C-suffix and -40 °C to +85 °C on the AC-suffix variants. The MC4558CP1 architecture is a classic bipolar voltage-feedback topology: a PNP input differential pair feeds a current-mirror active load, driving a high-gain second stage with class-AB push-pull output. The internal compensation capacitor rolls off open-loop gain at roughly 6 dB/octave above the dominant pole, which is why the unity-gain bandwidth exceeds the 1 MHz figure of the older 1458 by a factor of three. Designers can therefore use the part in unity-gain buffers without external compensation components. Typical applications include audio pre-amplifiers and tone-control stages, active filters and equalizers, transducer signal-conditioning front-ends, integrators, comparators, and general-purpose DC amplifiers in industrial controls. The DIP-8 package also makes the MC4558CP1 a preferred teaching reference for electronics curricula and breadboard prototyping. When designing with this op-amp, observe the supply headroom limits and pair the part with appropriately rated supply bypass capacitors placed within 1 cm of the VCC/VEE pins to maintain stability and minimize channel crosstalk. The matched amplifier pair simplifies layout when both channels must share identical bandwidth and phase response, e.g., in stereo audio front-ends. This page synthesizes distributor pricing, drop-in alternatives from the 1458/4558 family, and practical design notes not consolidated in any single manufacturer datasheet.

Запрос цены Контакты

MC56F8002VWL

MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP

The NXP MC56F8002VWL is a 16-bit Digital Signal Controller (DSC) from the MC56F800x family, built on the 56800E core architecture. It delivers 32 MHz of CPU clock speed (per DigiKey/NXP listing) and integrates 12 KB (6K x 16) of on-chip Flash program memory alongside a 28-pin SOIC package with 23 general-purpose I/O pins. The part operates from a 1.8 V to 3.6 V supply range, making it well suited to low-voltage embedded designs. A Digital Signal Controller (DSC) is a hybrid class of programmable device that combines the deterministic interrupt response and peripheral integration of a microcontroller with the Multiply-Accumulate (MAC) engine and Harvard bus structure of a Digital Signal Processor (DSP). The 56800E core executes instructions in a single cycle where possible and is positioned in the taxonomy as: DSC -> DSP/MCU hybrid -> microcontroller -> integrated circuit -> semiconductor. DSCs target real-time control loops where the math throughput of a DSP is needed but the application footprint, cost, and tool chain of an MCU are preferred. Key features of the MC56F8002VWL include the 56800E 16-bit core, 12 KB Flash program memory, 32 MHz maximum core frequency, 23 GPIO lines, and a supply range of 1.8 V to 3.6 V. The integrated peripheral set reduces external component count in motor, lighting, and power-conversion designs. According to the NXP MC56F8006/MC56F8002 reference manual, the family integrates peripherals such as timers, PWM modules, ADCs, and communication interfaces configured per the variant. Architecturally, the 56800E core uses a dual Harvard memory structure with separate program and data buses, allowing simultaneous fetches that improve sustained throughput on control algorithms. The 12 KB Flash is sufficient for closed-loop field-oriented motor control (FOC), digital lighting ballast loops, and small power-factor correction (PFC) firmware where deterministic performance is more important than raw memory size. Typical applications for the MC56F8002VWL include low-cost BLDC/PMSM motor drives, switch-mode power supplies (SMPS), digital LED lighting ballasts, appliance control boards, and small industrial control modules. The wide 1.8 V to 3.6 V supply and integrated analog peripherals make it attractive for power-conversion applications where a single IC handles both sensing and control. When designing with this part, ensure your firmware budget fits within 12 KB Flash plus available RAM, and check the variant's peripheral mix against your PWM, ADC, and communication requirements. NXP's CodeWarrior and the newer MCUXpresso DSC toolchains support this family, and engineers should plan for the variant-specific header files to avoid peripheral register mismatches. This page synthesizes distributor pricing, lifecycle signals, drop-in 56800E family alternatives, and practical design notes not found in the manufacturer datasheet alone. The NXP product page flags End-of-Life for MC56F8002VWL, so designers should review replacement and obsolescence options before committing the part to long-life programs.

Запрос цены Контакты

MC56F8006MLC

MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP

The NXP MC56F8006MLC is a 16-bit digital signal controller (DSC) from the MC56F800x family, featuring a 56800E core operating at 64 MHz bus clock with 32 MHz core MIPS throughput, 16 KB of on-chip Flash memory, and a 32-pin LQFP package. The device integrates DSP-class signal-processing capability with microcontroller peripheral integration on a single die, targeting cost-sensitive real-time control applications. A Digital Signal Controller (DSC) is a hybrid device class that combines a microcontroller's deterministic peripheral handling with a digital signal processor's mathematical pipeline. The 56800E core belongs to the family: 56800E core -> DSC -> microcontroller -> embedded processor -> semiconductor. Compared with a traditional 8/16-bit MCU, a DSC adds hardware multiply-accumulate, single-cycle MAC, and Harvard-style bus architecture, allowing closed-loop control loops, power-conversion math, and sensor fusion to run on a single chip without an external DSP partner. The MC56F8006 sits at the entry level of NXP's DSC portfolio, designed for mathematically intensive yet price-sensitive applications. Key specifications include 16 KB Flash program memory, 1.8 V to 3.6 V single-supply operation, 23 general-purpose I/O (GPIO) pins, on-chip 12-bit ADC, PWM modules suitable for motor and power control, and serial interfaces including SCI, SPI, and I2C. The device includes an internal relaxed oscillator with PLL-based frequency multiplication to derive the 64 MHz system clock from lower-cost external references. The MC56F8006 uses a Harvard-style 56800E architecture with separate program and data buses, allowing simultaneous fetch and operand access. The integrated peripheral set includes timers, PWM, ADC, and communication blocks, eliminating external components and reducing BOM cost. Built-in boundary scan and JTAG support simplify factory test and in-field firmware updates. Typical applications include BLDC and PMSM motor control in appliance fans and pumps, digital power conversion (PFC, LLC, buck/boost), LED lighting ballasts with analog dimming, and low-end industrial sensor conditioning. The wide 1.8 V to 3.6 V supply range supports both 2.5 V and 3.3 V system rails, simplifying multi-rail designs. When designing, ensure JTAG pins are accessible for factory programming and that the internal relaxed oscillator accuracy is acceptable for the target application. For motor control, leverage the integrated PWM and ADC synchronization rather than external triggering to reduce latency and BOM cost. This page synthesizes distributor pricing, NXP product-page lifecycle notes, parametric comparison with related 56F8xxx devices, and design notes covering JTAG access, oscillator selection, and motor-control timing - content not collated in the bare manufacturer datasheet.

Запрос цены Контакты

MC56F8006VLC

MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP

The NXP MC56F8006VLC is a 16-bit digital signal controller (DSC) from the 56800E core-based 56F800x family, integrating 16KB of Flash program memory, 32MHz maximum CPU clock, and a flexible peripheral set in a 32-pin LQFP package. It combines DSP-class signal processing throughput with microcontroller peripherals, targeting mathematically intensive real-time control applications such as digital power conversion, motor control, and sensor signal conditioning. What is a Digital Signal Controller? A DSC is a hybrid device that merges the deterministic math engine of a digital signal processor with the integrated peripherals and ease-of-use of a microcontroller. Architecturally, a DSC sits above a plain MCU in the embedded hierarchy (microcontroller -> digital signal controller -> DSP) and below a stand-alone DSP, occupying a sweet spot where signal-processing throughput must coexist with PWM, ADC, timers, and GPIO. The 56800E core uses a unified data/program memory map and a modified Harvard bus, with single-cycle MAC support that is essential for power-loop and field-oriented motor-control algorithms. Key features of the MC56F8006VLC include 16KB Flash (organized as 8K x 16), 2KB RAM, an internal Phase-Locked Loop for clock multiplication, multiple 16-bit timers, a 12-bit ADC, PWM modules suited for switch-mode power supplies, and serial peripherals (SCI, SPI, I2C). The device operates from 1.8V to 3.6V, supports industrial temperature range (-40C to +105C or -40C to +125C per device marking), and provides 23 general-purpose I/O pins. The LQFP-32 footprint offers 0.8mm pitch and an exposed-pad option on the family for improved thermal dissipation. Typical applications include digital DC/DC and AC/DC power converters, small BLDC and PMSM motor drives (fans, pumps, appliances), uninterruptible power supplies, induction cooking, smart sensors, and LED drivers with closed-loop current regulation. The combination of DSP math throughput, low BOM cost, and a familiar MCU development flow makes it a strong choice for cost-sensitive embedded control where 8-bit MCUs run out of headroom. When designing with this part, ensure the JTAG/OnCE debug interface is accessible on the board, allocate proper decoupling on AVDD/DVDD pins, and follow NXP's PCB layout guidance for the analog sections to keep ADC performance within spec. Note that NXP has issued End-of-Life notices for several 56F800x variants; engineers should verify lifecycle status before committing to new designs.

Запрос цены Контакты

MC56F8006VLF

MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP

NXP Semiconductors MC56F8006VLF is a 16-bit digital signal controller with a 32 MHz 56800E core, 16 KB of flash memory, and a 48-LQFP 7 x 7 mm package. It combines digital signal processing with microcontroller peripherals for mathematically intensive, power-sensitive, real-time control applications. A digital signal controller, or DSC, is a processor category positioned between a conventional microcontroller and a digital signal processor. MC56F8006VLF executes real-time control algorithms while providing general-purpose peripherals and embedded flash in one integrated device. Its 56800E architecture is intended for motor-control, power-conversion, and industrial automation functions where deterministic control and compact embedded integration matter. The verified manufacturer material identifies a 16-bit processing core, 32 MHz operating frequency, and 16 KB flash memory. NXP describes the entry-level MC56F8006 and MCF56F8002 devices as cost-effective solutions for power-sensitive, real-time control applications. The family integrates peripherals to reduce external component count while preserving the responsiveness required by feedback-control systems. MC56F8006VLF is supplied in a 48-LQFP package, making it suitable for conventional surface-mount PCB assembly. Its 16 KB flash capacity is sufficient for compact control firmware, configuration data, and application-specific code. The 32 MHz clock and 16-bit architecture support fast mathematical processing, while the integrated peripheral set helps simplify designs that would otherwise require separate interface and control components. Typical applications include digital motor control, power-supply regulation, industrial inverter control, signal conditioning, and embedded instrumentation. The part is particularly relevant when a system needs deterministic digital filtering or feedback calculations but does not require a high-end digital signal processor. NXP’s product family positioning emphasizes mathematically intensive, power-sensitive control rather than general-purpose processing. For a new design, verify supply voltage, peripheral assignments, timing, pin multiplexing, programming requirements, and package-level constraints against the manufacturer datasheet before committing the PCB. Because MC56F8006VLF is identified as end-of-life by the NXP product page, engineers should also confirm availability, lifecycle status, and approved sourcing options before starting a production release. This page combines verified manufacturer identity, distributor specifications, lifecycle context, package information, and practical sourcing considerations. It is intended to help engineers locate the datasheet, assess the device’s real-time control role, and determine whether a legacy design requires migration planning.

Запрос цены Контакты

MC56F8006VWLR

MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP

The NXP MC56F8006VWLR is a 16-bit 56800E-core Digital Signal Controller (DSC) that integrates the processing power of a DSP with the peripheral integration of a microcontroller, packaged in a 28-pin wide-body SOIC (SOIC-28-300mil). Per the manufacturer datasheet, it delivers up to 32 MIPS at 32 MHz core clock, with 16 KB of program Flash (organized as 8K x 16) and operates from a 1.8 V to 3.6 V supply. A Digital Signal Controller (DSC) is a hybrid device that occupies the architectural middle ground between a pure microcontroller (MCU) and a digital signal processor (DSP). It uses a modified Harvard architecture with a deterministic interrupt model, on-chip memory, and DSP-class multiply-accumulate instructions that allow closed-loop control loops to execute in a single instruction cycle. DSCs are widely used in digitally controlled switching power supplies, motor drives, sensor signal conditioning, and LED lighting where tight math latency matters more than raw GHz throughput. Key features of the MC56F8006 include 16 KB Flash / 2 KB RAM, a 6-channel PWM module suitable for three-phase or multi-channel DC/DC control, a 12-bit ADC, 23 GPIO lines, and on-chip relaxation oscillator. Integrated peripherals such as the programmable interval timer, queued serial peripheral interface (QSPI), and inter-integrated circuit (I2C) interface reduce external component count, lowering both BOM cost and PCB area. The device is qualified to -40 °C to +105 °C industrial temperature range. Architecturally, the 56800E core couples a unified data/program address space with dual operand fetches per cycle, enabling one-cycle MAC instructions that close PI or state-observer loops in motor-control firmware well within 32 MHz. The on-chip voltage regulator generates logic-level rails from the 1.8 V to 3.6 V external supply, simplifying analog/digital supply partitioning. Typical applications include switched-mode power supplies (SMPS), digital motor control (BLDC, PMSM, and stepper), solar micro-inverters, smart LED drivers, and industrial sensor conditioning. The wide operating voltage and industrial temperature grade also suit 12 V/24 V automotive-body and appliance platforms. A key design consideration is Flash endurance: typical 10,000 write/erase cycles per sector constrain in-application firmware updates. Designers should reserve a bootloader sector and follow NXP's recommended erase-modify-write sequence. This page synthesizes distributor pricing, parametric comparison against drop-in alternatives, and practical design guidance not typically consolidated on a single manufacturer datasheet.

Запрос цены Контакты

MC56F8013VFAE

MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP

The NXP MC56F8013VFAE is a 16-bit digital signal controller (DSC) in the 56800E 56F8xxx family, delivering 32 MHz core performance with 16 KB (8K x 16) of on-chip Flash and a 32-pin LQFP (7x7 mm) package. It integrates the computational power of a DSP with the peripheral set of a microcontroller on a single die, targeting cost-sensitive embedded control applications. The device operates from a 3.3 V supply and is qualified to AEC-Q100 for automotive deployments. What is a Digital Signal Controller? A Digital Signal Controller (DSC) is a hybrid class of embedded processor that combines microcontroller (MCU) peripherals and interrupt-driven control with the deterministic numeric throughput of a digital signal processor (DSP). In the system hierarchy, a DSC sits between a general-purpose MCU (e.g., ARM Cortex-M0) and a standalone DSP (e.g., TI C6000). DSCs are widely used in motor control, power conversion, and sensor-fusion applications where both deterministic control loops and arithmetic DSP kernels are required on one chip. The 56800E core used in the 56F8013 family adds a Harvard-style memory architecture and single-cycle MAC operations typical of DSP cores. Key features of the MC56F8013 include 16 KB Flash, 4 KB RAM, a 32 MHz 56800E core with single-cycle 16-bit multiply-accumulate, dual 6-channel PWM modules for motor drive, two 12-bit ADCs with up to 8 channels, and communication peripherals including SCI, SPI, and I2C. The 56F8013 derivative adds a CAN 2.0 A/B module versus the lower-feature 56F8011 sibling. On-chip regulators and a low-power Stop mode reduce quiescent draw for battery-connected systems. Typical applications span BLDC/PMSM motor drives (drones, e-bikes, appliances), digital switched-mode power supplies (PFC + LLC), automotive sensor interfaces, and industrial servo loops. The 56800E instruction set is C-friendly and supported by NXP's CodeWarrior and the newer MCUXpresso toolchain plus Processor Expert graphical configuration. Design considerations: maintain a clean analog ground island for ADC accuracy, place the 3.3 V decoupling network within 5 mm of the supply pins, and verify PWM timing closure against the application's control-loop rate. The LQFP-32 footprint allows hand-soldering and rework on prototype boards.

Запрос цены Контакты

MC56F8014VFAE

MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8014VFAE is a 16-bit digital signal controller microcontroller operating at up to 32 MHz, with 32 KB of flash memory, 8 KB RAM, PWM outputs, and COP/LVD support in a 32-LQFP (7x7 mm) package. It combines DSP and MCU functionality in the 56800E architecture, making it suitable for real-time motor-control and embedded signal-processing systems. A digital signal controller is a microcontroller architecture optimized for deterministic control loops and computationally intensive signal processing. The MC56F8014 combines a 16-bit core, programmable peripherals, ADC channels, PWM, and watchdog-related supervisory functions within one integrated device. Its dual Harvard-style architecture uses multiple execution units to support parallel instruction operations and efficient C-based control code. The verified device information identifies a maximum core frequency of 32 MHz, 32 KB program flash, and 8 KB RAM. The controller also includes one 5-channel PWM module and two 4-channel 12-bit ADC modules according to the supplied technical description. These resources support motor-control loops, digital power conversion, measurement systems, and embedded automation products. COP and low-voltage detection functions help supervise system operation and supply conditions. The MC56F8014VFAE is packaged in a 32-LQFP, 7x7 mm surface-mount package. The 32 MHz operating point provides a balance between control-loop responsiveness and embedded resource consumption, while the unified DSP/MCU architecture can reduce the need for separate general-purpose logic and signal-processing components. Exact pin functions, electrical limits, memory organization, timing, and peripheral behavior should be confirmed in the NXP 56F8014 technical data sheet. Typical applications include brushless DC motor control, digital motor controllers, power-conversion control, industrial automation, and embedded control systems with analog feedback. The 12-bit ADC resources suit sensor and current-voltage feedback, while PWM outputs support actuator and power-stage timing. CodeWarrior-oriented development and the MCU-style programming model support embedded firmware integration. Designers should verify the complete pin multiplexing, voltage limits, clock configuration, ADC conversion timing, PWM dead-time requirements, and package-level thermal conditions against the manufacturer datasheet before layout or firmware release. This page consolidates the supplied manufacturer, distributor, and cross-reference information while clearly identifying parameters that require datasheet confirmation.

Запрос цены Контакты

MC56F8025MLD

MC56F8025MLD - 16-Bit DSC 32MHz 32KB Flash 44-LQFP | NXP

The NXP MC56F8025MLD is a 16-bit digital signal controller (DSC) based on the 56800E core, running at 32 MHz with 32KB (16K x 16) of on-chip flash program memory, 4KB (2K x 16) of RAM, and 35 general-purpose I/O lines, housed in a 44-pin LQFP (10 x 10 mm) surface-mount package. A digital signal controller combines the computation throughput of a digital signal processor with the programming model, interrupt structure, and peripherals of a microcontroller. In the embedded hierarchy, the MC56F8025MLD sits between general-purpose MCUs and dedicated DSPs: it is a member of the NXP 56F8xxx DSC family, which in turn belongs to the broader category of embedded microcontroller ICs for real-time control. Key features include the dual Harvard-style 56800E architecture with three parallel execution units capable of up to six operations per instruction cycle, 32KB of flash memory supporting in-circuit reprogramming, and connectivity peripherals including I2C, LINbus, SCI, and SPI. The part operates over an industrial temperature range and uses gull-wing terminals on a square LQFP body. Technically, the 56800E core executes an MCU-style, C-compiler-friendly instruction set while providing DSP instructions such as single-cycle MAC, hardware loop instructions, and bit-manipulation capability. This allows a single device to run both the control loop (PID, state machines) and signal-processing tasks (filtering, transforms) without a second processor, reducing board area and BOM cost in motor and power-conversion designs. Typical applications include digital power supplies and power factor correction, BLDC/PMSM and stepper motor control, AC induction motor drives, uninterruptible power supplies, and industrial appliances requiring fast closed-loop control. Design consideration: budget flash and RAM carefully - at 32KB/4KB the device targets compact control loops, and C code with heavy DSP libraries can exhaust memory quickly; enable compiler optimization and consider fixed-point math. This page synthesizes distributor pricing, availability, alternatives, and practical design notes not found in the manufacturer datasheet, with data verified as of 2026-10-18.

Запрос цены Контакты

MC56F8025VLD

MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP

The NXP MC56F8025VLD is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, combining DSP performance with MCU-style peripheral integration, housed in a 44-pin LQFP (10x10 mm) package. It delivers up to 32 MIPS at 32 MHz, integrates 32 KB of program Flash and 8 KB of unified RAM, and targets cost-sensitive digital motor control and power conversion designs. The 56800E dual Harvard architecture features three parallel execution units capable of up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid device that fuses a microcontroller's deterministic peripheral set with a digital signal processor's MAC engine and single-cycle arithmetic units. In the system hierarchy it sits between microcontrollers (MCUs) and full digital signal processors (DSPs), and is itself a member of the broader power management and embedded control IC family. The 56800E family includes 16-bit fixed-point MAC, hardware DO loops, and an MCU-friendly programming model that compiles cleanly from C, enabling rapid DSP code generation without manual assembly tuning. Key features include dual 12-bit successive-approximation ADCs with up to 8 input channels, two PWM modules with six complementary outputs suitable for 3-phase motor drive, one quad-timer, two SCI (UART) ports, one SPI port, one I2C port, and an on-chip relaxation oscillator. The device operates from a 3.0 V to 3.6 V supply across -40 C to +105 C, with internal 2.5 V regulator-derived logic supply and brown-out reset. The 44-LQFP package provides 32 GPIO with high-current sink/source capability for direct gate-driver interface. Typical applications include low-cost BLDC and PMSM motor drives (appliance fans, pumps, small HVAC blowers), digital PFC and LLC power conversion front-ends, solar micro-inverter control loops, induction cookware quasi-resonant converters, and LED lighting ballast controllers. NXP's Processor Expert and FreeMASTER tooling provides auto-generated peripheral drivers and a real-time variable watch for in-circuit tuning, dramatically shortening the firmware design cycle. A practical design consideration: route the analog ADC reference (VREF) and analog supply (VDDA) separately from the noisy digital supply (VDD), and place the 1 uF and 0.1 uF decoupling pair within 3 mm of each supply pin. Avoid running PWM switching traces under the analog ADC input traces to minimize coupled noise.

Запрос цены Контакты

MC56F8027MLH

MC56F8027MLH - 16-Bit Automotive Digital Signal Controller

The NXP Semiconductors MC56F8027MLH is a 16-bit digital signal controller combining an MCU-style programming model with dedicated DSP execution resources. The device is associated with the 56800E dual Harvard-style core architecture, whose three parallel execution units can perform as many as six operations per instruction cycle. MC56F8027MLH is packaged in a 64-terminal square gull-wing LFQFP package measuring 10 mm by 10 mm and is identified as automotive-grade in the verified distributor data. A digital signal controller is a microcontroller optimized for real-time control and signal-processing workloads. Unlike a general-purpose microcontroller, it integrates execution resources and instructions that improve throughput for operations such as filtering, control-loop calculation, waveform processing, and mixed control-plus-DSP tasks. Within the embedded-device hierarchy, the MC56F8027MLH is a microcontroller, an embedded processor, and a real-time signal-processing controller. The verified NXP datasheet identifies MC56F8027MLH as part of the 56F8000 family of 16-bit digital signal controllers. Its architecture supports parallel operation, while its MCU-oriented programming model and optimized instruction set are designed to generate efficient DSP and control code. This combination makes the controller relevant to automotive electronics, motor and motion control, industrial automation, consumer equipment, and other embedded systems that must combine deterministic control with real-time signal processing. The three execution units operate in parallel within a dual Harvard-style architecture. According to the NXP manufacturer datasheet, this arrangement allows as many as six operations per instruction cycle, while the instruction set is designed for efficient use by C compilers. This provides a clearer software and hardware rationale than treating the device only as a conventional MCU: control-loop code and arithmetic signal-processing operations can share one programmable platform. Typical application areas include motor control, power conversion, industrial automation, automotive body or accessory electronics, audio and communication signal processing, and compact embedded instruments. Suitability depends on the exact peripheral configuration, memory variant, clock requirements, voltage range, temperature grade, and package-specific pin functions listed for the ordered device. Those detailed operating limits and resources must be confirmed in the NXP datasheet before schematic or firmware commitment. When designing a board, route all 64 terminals according to the package pinout and preserve the required power, ground, clock, programming, and signal-conditioning connections. Firmware and peripheral use should follow the datasheet's startup, interrupt, timing, and low-power procedures. The combination of 16-bit digital signal control, parallel core execution, and a 64-lead automotive package makes MC56F8027MLH a specialized embedded platform rather than a general register-compatible substitute for unrelated microcontrollers. This page consolidates the verified package, architecture, lifecycle-relevant sourcing, and manufacturer-datasheet links while clearly separating unavailable specifications. Its practical value is the combination of application guidance, design cautions, and a transparent assessment of replacement availability for this specialized DSP-controller platform.

Запрос цены Контакты

MC56F8027VLH

MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8027VLH is a 16-bit digital signal controller with a 56800E core, 32 KB flash memory, 32 MHz operating frequency, and a 64-LQFP package. It combines digital signal processing and microcontroller functions for embedded control, industrial lighting, and signal-processing systems. The device also provides 8 KB RAM, high-resolution PWM, a 12-bit ADC, and multiple serial interfaces according to the NXP product information. A digital signal controller is a microcontroller optimized for real-time signal acquisition, filtering, modulation, and control. Unlike a general-purpose microcontroller, the MC56F8027VLH integrates dedicated signal-processing peripherals with a deterministic embedded-control architecture. This makes it suitable for applications that must acquire analog signals, execute control calculations, and generate accurately timed outputs within one integrated device. The 56800E core provides 16-bit processing at up to 32 MHz, while 32 KB of flash supports firmware storage and 8 KB of RAM supports working data. The 12-bit ADC is useful for monitoring analog process variables, and the high-resolution PWM supports precision actuator, power-conversion, and lighting-control functions. Multiple serial interfaces enable connection to sensors, transceivers, memory, and industrial equipment. The 64-LQFP package provides a defined external pin arrangement and is suitable for conventional PCB assembly. Its larger lead pitch and exposed perimeter make it easier to inspect and manufacture than a fine-pitch package, although the device requires careful routing of power, ground, analog, and communication signals. The NRND lifecycle status indicates that the part should be selected carefully for new designs, while existing designs should verify availability and migration requirements before committing to production. Typical uses include industrial lighting controllers, motor and power conversion control, digital signal processing modules, instrumentation, and embedded systems requiring a combination of analog measurement and real-time computation. Firmware should account for the 12-bit ADC characteristics, PWM timing, serial peripheral configuration, and the package-specific pin multiplexing before hardware production. One key design consideration is to validate the complete signal path rather than selecting the controller only by clock rate. Analog input filtering, reference stability, PWM dead time or polarity, serial timing, and firmware interrupt latency determine system performance. Confirm the latest datasheet and NXP product-change notices before an NRND part is used in a new production program. This page consolidates verified manufacturer and distributor information, lifecycle status, package details, application guidance, and replacement analysis for engineers evaluating the MC56F8027VLH. Pricing and availability are referenced as of 2026-10-21 where distributor data provides them.

Запрос цены Контакты

MC56F8037MLHR

MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP

The NXP MC56F8037MLHR is a 16-bit Digital Signal Controller (DSC) built on the 56800E core, offering up to 32 MIPS performance with 32 KB of program Flash and 4 KB of unified data/Flash memory. It is housed in a 64-pin LFQFP package and integrates a 12-bit ADC, dual 6-channel PWM modules, and multiple serial interfaces for mixed-signal motor and power conversion control. A Digital Signal Controller is a hybrid device that combines the deterministic interrupt response and on-chip peripherals of a microcontroller with the high-throughput computational capability of a digital signal processor. In the broader component taxonomy, a DSC sits between a microcontroller (MCU) and a digital signal processor (DSP) under the umbrella of embedded controllers. The 56800E core implements a dual-Harvard architecture with three parallel execution units, allowing up to six operations per instruction cycle and C-friendly instruction set for efficient DSP-and-control code generation. Key features include 32 KB Flash with security, 2.5 KB RAM, a 12-bit ADC with 16 input channels and 2.5 us conversion time, two Pulse Width Modulator (PWM) modules each providing three complementary PWM pairs, and a Quad Timer module with four 16-bit timers. The device also integrates SCI, SPI, and I2C communications peripherals, plus an internal relaxation oscillator that operates without external crystals. The MC56F8037 is engineered for digital motor control and power conversion. Its PWM modules support center-aligned and edge-aligned modes with programmable fault inputs, while the high-speed ADC enables closed-loop current sensing. Multiple power-saving modes and on-chip regulator control reduce active and standby power for energy-conscious designs. Typical applications include BLDC and PMSM motor drives, switched-mode power supplies, solar inverters, uninterruptible power systems, and industrial variable-frequency drives. Automotive-grade parts in this family are widely used in electronic power steering and engine fan control where deterministic PWM timing is essential. When designing with the MC56F8037, allocate the ADC sample-and-hold window away from PWM edges to avoid switching noise coupling into current measurements. The internal relaxation oscillator provides adequate accuracy for many applications but an external crystal reference is recommended for CAN, USB, or any timing-sensitive serial link. This page synthesizes distributor pricing, pin-compatible drop-in alternatives, and practical design notes not found on the manufacturer datasheet front page, all cross-referenced against the NXP MC56F8037 datasheet and current distributor stock data.

Запрос цены Контакты

MC56F8037VLH

MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors

The NXP Semiconductors MC56F8037VLH is a 16-bit Digital Signal Controller (DSC) built on the 56800E core that combines DSP performance with microcontroller flexibility. It features 64 KB of on-chip flash memory, 32 MHz maximum core clock, and a 64-pin LQFP (10x10 mm) package. The 56800E core employs a dual Harvard-style architecture with three parallel execution units enabling up to six operations per instruction cycle. A Digital Signal Controller (DSC) is a hybrid semiconductor class that integrates a microcontroller's deterministic control peripherals with a digital signal processor's mathematical throughput on a single die. DSCs occupy the architectural middle ground between microcontrollers (MCUs), which optimize for control code, and digital signal processors (DSPs), which optimize for stream processing. Within the broader taxonomy, DSCs belong to the embedded processor family alongside MCUs, DSPs, and microprocessors, typically classified under power management-aware signal-chain and motor-control applications. Key features include dual 12-bit analog-to-digital converters (ADCs) with 4 microsecond conversion time, two high-speed Pulse Width Modulators (PWMs) supporting motor-control topologies, two analog comparators with programmable polarity, and dedicated timers. The device integrates 8 KB of unified RAM, 64 KB of flash with flash data retention rated at 20 years for less than 100 program/erase cycles, and a Cyclic Redundancy Check (CRC) hardware accelerator. Communication peripherals include SPI, I2C, UART, and CAN interfaces. The 56800E core executes 16-bit instructions from flash using a 3-stage pipeline with hardware DO loops, branch unit, and bit-manipulation unit, achieving sustained performance of 32 MIPS at 32 MHz. The unified memory architecture eliminates the need for separate program/data buses while preserving Harvard-style deterministic interrupt latency. Typical applications include industrial motor drives (BLDC, PMSM, ACIM), home appliances (washing machines, refrigerators, HVAC blowers), solar micro-inverters, and uninterruptible power supplies. The dual high-speed PWMs and 4-microsecond ADC make the device particularly suited to field-oriented control (FOC) loops in variable-frequency drives. Peripherals including the Quadrature Decoder, COP watchdog, and four 16-bit timers support direct interface to encoders, sensors, and power-stage gate drivers. When designing with this device, allocate 64 KB flash for both FOC control tables and application code, and budget 8 KB RAM for system variables plus MAC coefficient buffers. The 3.0 V to 3.6 V single-supply operation simplifies analog design but requires careful PCB layout to isolate noisy digital return currents from the ADC reference pins. Use the on-chip Relaxation Oscillator with external crystal bypass option for cost-sensitive designs, or drive an external crystal when motor-driving EMI must be minimized.

Запрос цены Контакты

MC56F8037VLHR

MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP

The NXP MC56F8037VLHR is a 16-bit digital signal controller (DSC) built on the 56800E core, delivering 32 MIPS at 32 MHz with 64 KB of program Flash and 32 KB of unified data/parameter RAM in a 64-pin LQFP (10x10 mm) package. The 56800E core is a dual Harvard-style architecture with three parallel execution units capable of issuing up to six operations per instruction cycle, providing DSP-class throughput alongside an MCU-style programming model. A digital signal controller (DSC) is a hybrid between a microcontroller and a DSP. It combines the deterministic control-loop responsiveness of an MCU with the MAC (multiply-accumulate) throughput and Harvard memory bandwidth of a DSP. Within the broader taxonomy, a DSC sits below a DSP but above a general-purpose microcontroller; it is optimized for closed-loop control of power-electronic and motion systems where firmware must both sample ADCs at high rates and execute vector math on the same instruction stream. The 56800E is NXP/Freescale's long-running DSC core family, having shipped in hundreds of millions of motor-control, appliance, and industrial-automation designs. Key features of the MC56F8037VLHR include dual high-speed 6-channel PWM modules optimized for 3-phase motor drive, a 12-bit ADC with up to 8 input channels, three 16-bit timers, a queued serial peripheral interface (QSPI), two SCI/UARTs, an I2C port, a CAN 2.0 A/B module, an on-chip relaxation oscillator with PLL for flexible clocking, and a computer operating properly (COP) watchdog. The device operates from 3.0 V to 3.6 V supply and supports the industrial -40C to +105C or extended -40C to +125C junction temperature ranges. Architecturally, the 56800E core uses four 36-bit accumulators fed by a 16x16-bit MAC producing 36-bit results, an Address Generation Unit (AGU) with hardware looping, and a Bit Manipulation Unit (BMU) for efficient bit-field control code. The unified 32 KB data RAM doubles as parameter RAM, and the 56800E instruction set is friendly to C compilers while remaining compact for hand-written assembly in time-critical interrupt service routines. Typical applications include variable-frequency drives (VFDs), sensorless and sensored BLDC/PMSM motor control for home appliances (washing machines, refrigerators, air-conditioner compressors), industrial servo drives, HVAC blowers, solar micro-inverters, and digital power-conversion control loops. The combination of deterministic PWM timing, fast ADC-to-PWM latency, and CAN connectivity is particularly suited to multi-axis industrial machinery. Designers should note that the 64-pin LQFP version is one of three package options in the family; the part suffix (VLH = LQFP-64, VLH is the standard, R = tape and reel) maps directly to a given distributor SKU. When migrating from the 56F8025/56F8027, careful review of the peripheral pin map is required because several PWM and GPIO functions are remapped across package options. This page synthesizes distributor pricing, drop-in same-package alternatives from the 56F803x family, and practical design notes for 3-phase motor control not found in the manufacturer datasheet.

Запрос цены Контакты

MC56F8122VFAE

MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP

The NXP MC56F8122VFAE is a 16-bit digital signal controller (DSC) from the 56F8300 family, built on the 56800E core, delivering up to 60 MIPS performance at 60 MHz with 32 KB of on-chip Flash memory, packaged in a 48-pin LQFP (7x7 mm). It combines the processing power of a DSP with the functionality of a microcontroller, targeting motor control, power conversion, and embedded signal processing applications. A digital signal controller is a hybrid class of MCU that merges a microcontroller's deterministic peripheral set and ease of use with a DSP's single-cycle MAC and Harvard bus architecture. The 56800E core extends this model with dual Harvard buses, a unified data/program space, and orthogonal instruction set, enabling fixed-point arithmetic at DSP-like throughput without sacrificing C-friendly code density. Key features of the MC56F8122VFAE include 32 KB Flash program memory, 4 KB RAM, two 6-channel PWM modules suited for 3-phase motor drive, a 12-bit ADC with multiple input channels, two quad timers, SCI, SPI, and I2C communication peripherals, plus JTAG/OnCE debug. The 48-LQFP package exposes extended ADC and timer I/O versus the lower-pin 56F8014 variant. The architecture pairs a 40 MHz core clock with separate peripheral clocks and a peripheral set tuned for closed-loop control loops. Hardware accumulators, barrel shifter, and DO-loop primitives accelerate inner-loop math such as Park/Clarke transforms, FIR filters, and PID compensation typically required by field-oriented control algorithms. Typical applications include 3-phase AC induction and BLDC motor drives, sensorless and Hall-effect commutation, digital PFC, uninterruptible power supplies, solar inverters, and industrial process control. The 56800E toolchain (CodeWarrior, MCUXpresso-style SDKs, and FreeMASTER real-time debug) supports C/C++ development with DSP intrinsics. When designing with this part, plan the LQFP-48 PCB layout with decoupling on every AVDD/DVDD pair and route analog references with guard traces. NRND status (per NXP product page) means new designs should evaluate 56F84xxx successors where possible.

Запрос цены Контакты

MC56F8123VFBE

MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP

The NXP Semiconductors MC56F8123VFBE is a 16-bit digital signal controller with a 56800E core, 40 MHz processing speed, 32 KB of Flash program memory, and a 64-LQFP 10 x 10 mm package. It combines microcontroller integration with digital signal processing for embedded control systems. The device is identified by NXP as part of the 56F8xxx family and is supplied with SCI and SPI connectivity, power-on reset, watchdog, and 27 I/O according to the provided component data. A digital signal controller is a controller that combines a microcontroller’s peripheral integration and deterministic embedded-control role with DSP-oriented processing. The MC56F8123VFBE therefore belongs to the broader digital signal processor and controller hierarchy rather than serving only as a general-purpose microcontroller. Its 16-bit architecture and 40 MHz operating speed are suited to motor, industrial-control, embedded signal-processing, and communications-oriented designs where control-loop execution and integrated peripherals are important. The key verified features are a 16-bit 56800E processor, 40 MHz maximum clock frequency, 32 KB Flash organized as 16K x 16, 8K x 8 RAM, SCI, SPI, power-on reset, watchdog, and 27 I/O. The listed package is a 64-LQFP 10 x 10 mm surface-mount package. The verified data also identifies the component as a digital signal controller with 16-bit architecture; detailed electrical limits, temperature ratings, ADC specifications, timer details, and memory endurance were not included in the supplied search results and must be checked against the manufacturer datasheet before design release. MC56F8123VFBE is suitable for embedded motor-control systems, industrial automation controllers, communications interfaces, and general digital signal-processing products. SCI connectivity can support serial communications, while SPI can connect to external sensors, converters, memory, or display-related peripherals. The 27 I/O count provides a defined interface budget for external control signals, subject to the exact pin functions and multiplexing requirements in the datasheet. A key design consideration is that replacement or upgrade decisions must compare the complete peripheral map, memory organization, pin multiplexing, clocking, power supply, and software toolchain rather than relying only on the family name. The verified package is 64-LQFP, so any proposed substitute must be checked for exact footprint and pin compatibility. Pricing and stock should also be confirmed with an authorized distributor because the provided distributor snippets do not provide a complete current price table. This product record synthesizes the verified NXP and distributor specifications, package identity, connectivity features, and application guidance. It also highlights where manufacturer-datasheet verification remains necessary, helping engineers move from component discovery to a controlled embedded-control design review.

Запрос цены Контакты

MC56F8145VFGE

MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP

The NXP MC56F8145VFGE is a 16-bit digital signal controller (DSC) from the 56800E core family, integrating 128KB of Flash memory, 40 MHz CPU performance, and a rich peripheral set into a 128-pin LQFP package. It combines microcontroller (MCU) determinism with DSP-class arithmetic throughput, targeting real-time motor control, power conversion, and sensor-processing applications. A digital signal controller is a hybrid device that merges a microcontroller's interrupt-driven control architecture with a DSP's single-cycle MAC engine. In the system taxonomy, the MC56F8145 sits between a generic MCU and a full DSP; its 56800E core executes parallel moves and multiply-accumulates in a single instruction cycle, enabling closed-loop control loops at high PWM frequencies while still behaving like a conventional MCU for housekeeping tasks. Key features include 128KB (64K x 16) on-chip Flash, 40 MHz core clock, integrated PWM modules with up to 6 channels, dual 12-bit ADCs, quadrature decoder, CAN, SCI, SPI, I2C, and a 16-bit timer subsystem. The 56800E Harvard architecture separates program and data memory buses, eliminating fetch bottlenecks during sustained MAC operations. The device targets motor control (BLDC, PMSM, ACIM), digital power conversion (PFC, LLC, full-bridge), and industrial sensor interfacing. Its on-chip peripherals include PWM with dead-time insertion and fault inputs, making it well suited for three-phase inverter drives. The 128-pin LQFP exposes sufficient GPIO and analog channels for typical 3-phase inverter plus housekeeping requirements. Engineers should review the peripheral mix carefully when selecting a variant within the 56F81xx family - the MC56F8145/46/47 differ in Flash/RAM size and peripheral count, but share the same 56800E core, instruction set, and toolchain. This page synthesizes distributor pricing, drop-in 56F81xx alternatives, and practical design notes not consolidated in the manufacturer datasheet.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

MC3488AP1 Dual EIA-423/EIA-232D Line Driver | onsemi

MC44BS373CAD - PLL-Tuned UHF/VHF Audio/Video Modulator | NXP

MC44BS373CAEF - NTSC/PAL Audio/Video RF Modulator | NXP SOIC-16

MC44BS373CAFC - NTSC/PAL Audio/Video RF Modulator IC | NXP

MC44BS374T1AEF - PLL-Tuned UHF/VHF A/V Modulator | NXP

MC44BS374T1EFR2 - PLL UHF/VHF A/V Modulator, 16-SOIC | NXP

MC4558CP1 - Dual 2.5MHz Wide-Bandwidth Op-Amp DIP-8 | onsemi

MC56F8002VWL - 16-bit 56800E DSC, 32MHz, 12KB Flash 28-SOIC | NXP

MC56F8006MLC - 16-bit DSC, 56800E Core, 16KB Flash | NXP

MC56F8006VLC - 16KB Flash 32MHz DSC | NXP 32-LQFP

MC56F8006VLF - 16-Bit 32MHz DSC, 16KB Flash | NXP

MC56F8006VWLR - 16KB Flash 32MHz 56800E DSC | NXP

MC56F8013VFAE - 16-Bit 32MHz DSC, 16KB Flash, LQFP-32 | NXP

MC56F8014VFAE - 32MHz 16-Bit DSC with 32KB Flash | NXP

MC56F8025MLD - 16-Bit DSC 32MHz 32KB Flash 44-LQFP | NXP

MC56F8025VLD - 16-bit DSC, 56800E core, 32KB Flash, 32MHz, 44-LQFP

MC56F8027MLH - 16-Bit Automotive Digital Signal Controller

MC56F8027VLH - 16-Bit 32MHz DSC with 32KB Flash | NXP

MC56F8037MLHR - 32KB Flash 56800E DSC, LFQFP-64 | NXP

MC56F8037VLH - 16-bit DSC, 56800E Core, 64KB Flash, 32MHz LQFP-64 | NXP Semiconductors

MC56F8037VLHR - 16-bit 56800E DSC, 64KB Flash, 32MHz | NXP

MC56F8122VFAE - 16-bit DSC, 32KB Flash, 40MHz, 48-LQFP | NXP

MC56F8123VFBE - 16-Bit 40MHz DSC with 32KB Flash | NXP

MC56F8145VFGE - 16-bit DSC, 56800E, 128KB Flash, 40MHz | NXP