Интегральные схемы

MCP625-E/MF

MCP625-E/MF - 20MHz Dual Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP625-E/MF is a dual general-purpose operational amplifier with a 20 MHz gain-bandwidth product, 10 V/µs slew rate, and rail-to-rail input and output operation. Designed for low-voltage signal conditioning, the device operates from 1.8 V and is housed in a 10-DFN 3x3 mm surface-mount package. An operational amplifier is an analog signal-conditioning IC that uses high-gain feedback to amplify voltage differences. The MCP625-E/MF belongs to the operational-amplifier hierarchy within amplifier ICs and semiconductor electronics. Its dual-circuit configuration allows two independent amplifier channels in one package, reducing board area in portable, industrial, automotive, and test-and-measurement equipment. The principal performance features include a 20 MHz gain-bandwidth product, 10 V/µs slew rate, rail-to-rail inputs and outputs, and operation down to 1.8 V. The automotive-oriented E temperature grade supports extended-temperature operation. These characteristics make the amplifier suitable for sensor interfaces, current sensing, active filtering, audio signal paths, and general low-voltage analog systems. At a 20 MHz gain-bandwidth product, a closed-loop gain of 10 corresponds to an approximate bandwidth of 2 MHz before other practical limitations become significant. The 10 V/µs slew rate allows relatively fast transitions and reduces distortion when driving higher-capacitance loads. Rail-to-rail input capability improves usable input range near the supply rails, while rail-to-rail output operation increases output-voltage headroom. Typical uses include battery-powered sensor conditioning, industrial control signals, automotive interface circuits, instrumentation amplifiers, active filters, and low-voltage audio electronics. In a current-sensing application, the two channels can amplify a small differential voltage and buffer an unrelated reference or monitor signal, provided the common-mode and output ranges satisfy the electrical limits. Layout and stability remain important design considerations. Place the device close to the feedback network and sensitive input nodes, keep high-current return paths out of analog signal paths, and provide an exposed-pad thermal connection according to the manufacturer land pattern. Stable operation with capacitive loads may require an isolation resistor between the amplifier output and the load. This product page combines the manufacturer-device identity, distributor specifications, package information, technical application guidance, and replacement-selection context to support faster engineering decisions. The Request a Quote form provides current commercial availability, lead time, and purchasing support for the MCP625-E/MF.

Запрос цены Контакты

MCP6272-E/P

MCP6272-E/P - Dual 2MHz RRO Op Amp | Microchip

The Microchip Technology MCP6272-E/P is a dual-channel operational amplifier with a 2 MHz typical gain-bandwidth product, rail-to-rail input and output operation, and an 8-pin DIP package. It operates from a single supply up to 5.5 V, draws 170 µA typical supply current, and provides a minimum common-mode rejection ratio of 70 dB. The typical input offset voltage is 3 mV, and the extended-temperature version supports operation to +125 °C. These characteristics place the device in the general-purpose operational-amplifier category, where low power, moderate bandwidth, and input/output swing close to the supply rails are useful for portable and precision signal-conditioning systems. An operational amplifier, commonly abbreviated op amp, is an analog integrated circuit that amplifies the difference between two input voltages. A dual op amp contains two amplifier channels in one package, allowing simultaneous amplification or the construction of differential, filtering, comparator, and feedback circuits. The MCP6272 family combines a 2 MHz gain-bandwidth product with 65° phase margin and rail-to-rail input and output characteristics, making it suitable for general-purpose low-power signal conditioning. Key features include two amplifier channels, 2 MHz typical gain bandwidth, 170 µA typical supply current, and operation from a single supply to 5.5 V. The input offset voltage is 3 mV, while the common-mode rejection ratio is at least 70 dB. Rail-to-rail input and output behavior allows the amplifier to process signals near the low and high ends of its supply range. The extended-temperature capability reaches +125 °C, supporting applications with a wider environmental range than standard commercial-grade devices. The 2 MHz gain-bandwidth product defines the approximate frequency range available for useful closed-loop gain. For example, a 10-times voltage gain would place the amplifier near 200 kHz based on the 2 MHz gain-bandwidth product. The 65° phase margin provides stability-oriented design guidance for common feedback configurations. These figures make the MCP6272 practical for low-to-moderate-frequency instrumentation, sensor interfaces, audio preamplification, filtering, and general embedded analog signal paths rather than demanding high-speed video or RF amplification. Typical uses include battery-powered sensor conditioning, buffered ADC inputs, low-frequency active filters, audio input stages, and general dual-channel analog interfaces. The low 170 µA typical supply current is particularly useful in compact embedded systems where each additional milliamp can affect battery life. Two channels also reduce component count when a board needs paired amplification, differential buffering, or independent signal paths. Design should account for the 5.5 V maximum supply, input common-mode range, output swing, load capacitance, and stability requirements. Place the bypass capacitor close to the supply pins and route feedback components to minimize parasitic effects. Confirm the intended operating temperature and package constraints against the manufacturer datasheet before releasing a production PCB. This product page combines manufacturer specifications, package information, sourcing guidance, application fit, and engineering-focused design notes. It also distinguishes true same-package drop-in replacements from nearby family variants in other packages, helping designers avoid substitutions that require PCB or footprint changes.

Запрос цены Контакты

MCP6273-E/P

MCP6273-E/P - 2 MHz Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP6273-E/P is a single-circuit, rail-to-rail operational amplifier with a 2 MHz gain-bandwidth product, 65-degree phase margin, and typical quiescent current of 170 uA. The device operates from a single supply as low as 2.0 V and is offered in an 8-pin PDIP package. Its combination of low power consumption, wide bandwidth, and rail-to-rail input and output capability makes it useful for portable instrumentation, sensor interfaces, and low-voltage signal-conditioning systems. An operational amplifier, or op amp, is an analog integrated circuit that amplifies the difference between two input voltages while providing high input impedance and low output impedance. The MCP6273 belongs to the operational-amplifier hierarchy within analog ICs and power-management signal conditioning. Rail-to-rail input capability allows the input common-mode voltage to extend close to both supply rails, while rail-to-rail output operation supports low-amplitude signals in low-voltage systems. The family’s 2 MHz gain-bandwidth product provides useful bandwidth for low-frequency precision and general-purpose analog signal paths. A 65-degree phase margin supports stable operation in common feedback configurations. The typical 170 uA quiescent current reduces the standing power requirement of battery-operated equipment, and the 2.0 V minimum single-supply operation makes the amplifier compatible with modern low-voltage rails. The MCP6273-E/P is specified in an 8-pin PDIP package for through-hole PCB assembly. This amplifier is intended for signal paths that need more bandwidth than a micropower comparator but do not require the drive or speed of a high-performance precision amplifier. Its rail-to-rail behavior is particularly valuable when the usable input range must cover much of the supply voltage. Designers should still evaluate output-current capability, noise, input bias current, common-mode limits, and stability under the intended loading before fixing a gain or output stage. Typical uses include low-frequency sensor conditioning, portable measurement systems, audio input stages, current-sense buffers, and general-purpose analog gain blocks. The MCP6273-E/P can also form the active element in filters and instrumentation amplifiers when component tolerances and operating bandwidth support the required accuracy. The 2.0 V operating supply and 170 uA typical quiescent current are particularly attractive for compact battery-powered products. The principal design consideration is stable feedback compensation. Keep the feedback network close to the amplifier, avoid excessive capacitive loading at the output, and confirm the selected gain against the 2 MHz gain-bandwidth product and 65-degree phase margin. The manufacturer datasheet should be used to assign the eight package pins, select input and output capacitors, and verify operating limits. This product page combines package information, searchable technical attributes, verified commercial availability, replacement guidance, and practical analog-design notes in one searchable reference. It helps engineers distinguish the MCP6273-E/P from related package and amplifier options before committing a PCB footprint or low-voltage power budget.

Запрос цены Контакты

MCP6274-E/P

MCP6274-E/P - 2 MHz Rail-to-Rail Quad Op Amp | Microchip Technology

The Microchip Technology MCP6274-E/P is a 170 uA, 2 MHz gain-bandwidth-product, rail-to-rail input/output operational amplifier quad in a 14-DIP package. The four-circuit device operates from a single supply up to 5.5 V and is designed for low-power analog signal conditioning, sensor buffering, and general-purpose voltage amplification. Its rail-to-rail input and output stages support operation near the supply rails, while the 0.9 V/us slew rate and 65 degree phase margin provide useful AC performance for low-frequency signal paths. An operational amplifier is an integrated analog amplifier that uses differential input voltage to control an output voltage or current. The MCP6274 belongs to the operational-amplifier hierarchy within analog and mixed-signal semiconductors, commonly used to amplify weak sensor signals, buffer high-impedance sources, perform analog filtering, and establish stable voltage references. The MCP6274-E/P is the quad version of the MCP6271/1R/2/3/4/5 family, allowing four amplifiers in one package and reducing board area in multi-channel systems. The MCP6274-E/P provides a typical gain-bandwidth product of 2 MHz, typical supply current of 170 uA, and a typical slew rate of 0.9 V/us. Its rail-to-rail input and output capability is useful when signal levels approach the positive or negative supply limits. The extended-temperature option is intended for operating temperatures up to +125 C, as identified in the family documentation, making the device suitable for industrial and instrumentation environments when its full electrical limits are respected. The device is specified as a general-purpose amplifier with four circuits in a 14-DIP package measuring 0.300 inch, or 7.62 mm, pitch. The DIP format is useful for prototyping, through-hole industrial equipment, and designs that favor a large package with generous pin spacing. The 14-pin arrangement contains four amplifier channels and their associated supply and ground connections, allowing convenient point-to-point wiring or socketed implementation. Typical uses include low-frequency sensor conditioning, current-to-voltage conversion, audio preamplification, instrumentation buffering, active filtering, and general signal amplification. Because the amplifier is intended for single-supply operation, system designers should establish the input common-mode range, output swing, load current, stability, and noise margins around the actual supply voltage. The manufacturer family documentation identifies a 2 MHz GBWP and 65 degree phase margin as characteristic of the family. For PCB implementation, place the device so that each power and ground pin connects to low-impedance supply planes, keep input and feedback traces short, and provide bypassing capacitance close to the supply pins. Avoid placing high-current return paths beneath the input circuitry. When substituting parts, confirm the exact 14-DIP pinout, operating voltage, input common-mode range, output swing, slew rate, and stability requirements rather than relying only on the advertised bandwidth. This page combines the MCP6274-E/P manufacturer specifications, package information, pricing evidence, application guidance, and drop-in replacement considerations into a practical engineering reference for selecting and implementing the device.

Запрос цены Контакты

MCP6283-E/P

MCP6283-E/P - 5MHz Dual RRIO Op Amp | Microchip

Microchip Technology MCP6283-E/P is a dual rail-to-rail input and output operational amplifier with a 5 MHz gain-bandwidth product, 450 µA typical supply current, and a 6-pin SOT-23 package. Designed for low-power systems, the device operates from a single 5 V supply and supports extended-temperature operation from -40°C to +125°C. Its rail-to-rail input and output characteristics allow the amplifier to process signals near the positive and negative supply limits without requiring a separate mid-supply reference. An operational amplifier is a voltage-gain and signal-conditioning semiconductor used in analog, mixed-signal, and power-control systems. Common functions include buffering, amplification, active filtering, current-to-voltage conversion, differential sensing, and feedback control. Rail-to-rail input and output, commonly abbreviated RRIO, extends the usable input and output range toward the supply rails. The MCP6283-E/P belongs to Microchip's MCP6281, MCP6281R, MCP6282, MCP6283, MCP6284, and MCP6285 family of low-power operational amplifiers. The MCP6283-E/P provides a typical gain-bandwidth product of 5 MHz and a 65° phase margin. Its typical slew rate is 2.5 V/µs, while the typical supply current is 450 µA per amplifier. The device also specifies 85 dB common-mode rejection and 0.0050 µA typical input bias current. These characteristics make it suitable for low-power sensor conditioning, current measurement, filtering, buffering, and portable-equipment signal paths where amplifier current consumption is important. The single-supply architecture simplifies power planning in battery-operated and embedded systems. Rail-to-rail inputs are particularly useful when sensor outputs approach ground, while rail-to-rail outputs improve output swing for low-voltage analog signals. Designers should nevertheless account for input and output common-mode limits, output-current capability, capacitive-load stability, and the voltage drop across the power pins when establishing system operating limits. Typical uses include portable medical instruments, industrial sensor interfaces, battery-powered monitoring equipment, low-voltage data acquisition, active analog filters, and audio input conditioning. The extended temperature range allows use in industrial environments where the ambient or enclosure temperature can reach 125°C, provided the board layout maintains the intended operating conditions. For PCB implementation, place the SOT-23-6 close to the signal source and receiver, route the ground return directly to the device ground pin, and decouple the supply with a local bypass capacitor. Check the recommended capacitor type and value in the manufacturer datasheet for the intended gain, noise, and stability requirements. This page consolidates the device specifications, sourcing workflow, application guidance, and replacement considerations into one engineering-focused reference.

Запрос цены Контакты

MCP629-E/ML

MCP629-E/ML - 20 MHz Quad Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP629-E/ML is a four-circuit, general-purpose operational amplifier built around the MCP62x family and specified in a 16-pin VQFN exposed-pad package. Its headline characteristics are a 20 MHz typical gain-bandwidth product, 10 V/us typical slew rate, 13 nV/Hz typical input noise at 1 MHz, and calibrated input offset of no more than ±200 uV. The device uses mCal self-calibration at power-up to reduce offset error and is intended for applications requiring low offset, wide bandwidth, and rail-to-rail input or output operation. An operational amplifier is an active analog signal-conditioning device that uses high-gain feedback to amplify small voltage differences. In the broader hierarchy, an operational amplifier belongs to the amplifier IC and analog signal-processing categories, while the MCP629-E/ML is specifically a quad, general-purpose precision amplifier. Its four amplifiers can support independent signal paths or be used in combinations such as instrumentation stages, active filters, buffers, and low-level sensor conditioning. The MCP62x family combines low offset with self-calibration. At power-up, the amplifiers are self-calibrated using mCal to improve input offset performance. The calibrated input offset specification is ±200 uV maximum, making the device suitable for applications where offset error must remain controlled without relying on an external trimming network. The 20 MHz gain-bandwidth product supports wider closed-loop bandwidth than lower-bandwidth precision amplifiers, while the 10 V/us slew rate helps preserve large-signal response in transients. Typical uses include precision sensor interfaces, audio signal conditioning, data acquisition front ends, active filtering, and low-level control loops. Rail-to-rail operation can simplify designs in systems where input or output signals approach the supply rails, although the exact input and output common-mode limits should be checked against the manufacturer datasheet for the selected supply voltage. The exposed pad supports thermal dissipation, but layout should provide a low-impedance thermal and ground connection. When placing the MCP629-E/ML in a PCB design, use the 16-pin QFN land pattern and follow the manufacturer’s recommended layout for decoupling and exposed-pad connections. Keep input and output routing short, place bypass capacitors close to the supply pins, and avoid routing sensitive high-impedance nodes next to switching or digital return paths. The device is available in a tube package according to the product listing information. This page combines the manufacturer product description, distributor specifications, package details, comparison information, and application guidance for engineers evaluating the MCP629-E/ML. It emphasizes the verified 20 MHz bandwidth, 10 V/us slew rate, 13 nV/Hz noise, ±200 uV calibrated offset, four-channel configuration, and 16-pin VQFN footprint. Use the individual spec tables and manufacturer datasheet for detailed ordering, electrical-limit, and application-specific guidance.

Запрос цены Контакты

MCP6291-E/P

MCP6291-E/P - 10MHz RAIL-to-Rail Op Amp | Microchip

The Microchip Technology MCP6291-E/P is a single, general-purpose operational amplifier with a 10 MHz gain-bandwidth product, 65-degree phase margin, and 7 V/us slew rate. It operates from a single supply as low as 2.4 V to 5.5 V, draws 1 mA typical quiescent current, and provides rail-to-rail input and output operation in an 8-pin PDIP package. An operational amplifier is a voltage-gain component used to amplify small signals, buffer high-impedance sources, compare voltages, and implement feedback-control loops. Within the broader semiconductor hierarchy, the MCP6291-E/P belongs to the amplifier IC class, where its combination of low power consumption, wide bandwidth, and rail-to-rail behavior supports portable instrumentation, sensor interfaces, and low-voltage signal-processing systems. Principal operating features include 2.4 V to 5.5 V single-supply operation, 10 MHz typical gain-bandwidth product, 65-degree phase margin, 7 V/us slew rate, and 85 dB typical common-mode rejection. Rail-to-rail inputs allow signals to approach the supply limits, while rail-to-rail outputs improve dynamic range in low-voltage systems where the output must swing close to the available supply rails. The low-power architecture is significant because it limits the supply demand of continuously operating analog stages. The 1 mA typical quiescent current is particularly useful in battery-powered equipment, while the 10 MHz bandwidth provides useful closed-loop performance for moderate-frequency signals. The 7 V/us slew rate helps preserve large-signal response when the amplifier drives higher capacitance or operates at higher frequencies. Typical applications include portable sensor conditioning, low-voltage audio and communication interfaces, current-to-voltage conversion, active filtering, buffer stages, and precision threshold detection. The device is also suitable for laboratory and test equipment operating from a 5 V rail where a conventional through-hole package simplifies prototyping, inspection, and manual assembly. When using the MCP6291-E/P, account for output-current capability, capacitive-load stability, input common-mode range, and the noise gain selected by the feedback network. Decoupling capacitors should be placed close to the supply pins, and unused inputs must be tied to a defined common-mode potential rather than left floating. This product page combines the manufacturer specifications with application-oriented engineering guidance, package and pin information, design notes, and a strict assessment of drop-in replacement options. The analysis distinguishes genuine pin-compatible substitutions from package-only equivalents so engineers can make PCB-level decisions without relying on incomplete cross-reference listings.

Запрос цены Контакты

MCP6293-E/P

MCP6293-E/P - 10MHz Low-Power R-R Op Amp | Microchip

Microchip Technology MCP6293-E/P is a single-circuit, low-power, rail-to-rail operational amplifier with a 10 MHz gain-bandwidth product, 65° phase margin, and 1 mA typical quiescent current. It operates from a single supply as low as 2.4 V, supports a supply range up to 6.0 V, and is packaged in an 8-pin PDIP through-hole package. The MCP6293-E/P variant supports an extended operating-temperature range of -40°C to +125°C. An operational amplifier, or op amp, is an analog amplifier that uses very high open-loop gain to amplify the difference between two input voltages. The rail-to-rail input and output architecture allows the MCP6293-E/P to operate close to the positive and negative supply rails, making it useful in portable instrumentation, sensor signal conditioning, audio, and low-voltage control systems where the available signal range is limited. The family’s 10 MHz gain-bandwidth product provides useful bandwidth for moderate-frequency signal paths. A 65° phase margin supports stable operation in common closed-loop amplifier configurations. The 1 mA typical quiescent current reduces the supply burden in battery-operated and compact embedded equipment, while the 2.4 V minimum single-supply operation supports compatibility with low-voltage systems. The MCP6293-E/P uses rail-to-rail inputs and outputs, allowing input and output voltages to approach the supply limits without requiring a separate negative supply. This characteristic is particularly valuable in low-voltage sensor interfaces, where the sensed signal can occupy much of the available input range. Its single-channel configuration also simplifies PCB routing when each signal requires independent gain or buffering. Typical uses include portable sensor conditioning, low-voltage audio stages, active filtering, transducer amplification, and general-purpose analog buffering. The 8-pin PDIP package remains convenient for through-hole prototypes, educational designs, laboratory assemblies, and systems assembled from leaded components rather than compact surface-mount production. Designers should verify the complete electrical limits, unity-gain stability configuration, input bias behavior, output-swing limits, and recommended external compensation values in the Microchip MCP6291 family data sheet. PCB layout should keep input, feedback, and ground connections short to minimize parasitic capacitance and maintain the intended bandwidth and stability. This page combines package-specific identification, application guidance, practical design notes, and a parameter-focused replacement analysis to support faster component selection and PCB design for the MCP6293-E/P.

Запрос цены Контакты

MCP6294-E/P

MCP6294-E/P - Quad 10MHz RRIO Op Amp | Microchip

The Microchip Technology MCP6294-E/P is a quad operational amplifier with a 10 MHz typical gain-bandwidth product, 8.7 nV/√Hz input noise, and rail-to-rail input and output capability in a 14-pin plastic DIP package. It operates from a 2.4 V to 6.0 V single supply and is intended for low-power applications requiring four amplifiers in one package. An operational amplifier, or op amp, is a high-gain analog building block used to amplify, buffer, filter, compare, and drive signals. The MCP6294 belongs to the operational-amplifier hierarchy, where it combines low-noise voltage amplification with a wide common-mode input range. Rail-to-rail input and output operation allows signals to approach the supply limits, which is useful in low-voltage sensor, signal-conditioning, and mixed-signal systems. The principal features are 10 MHz typical gain-bandwidth product, 65° phase margin, 8.7 nV/√Hz input noise, and 50 mA output-current capability. The MCP6294-E/P consumes 1.0 mA typical quiescent current per amplifier and operates over an extended temperature range of -40°C to +125°C. These characteristics balance bandwidth, noise, supply voltage, and power consumption rather than maximizing any single parameter. Each of the four amplifiers includes rail-to-rail input and output stages. The common-mode input range extends beyond the conventional input stages, improving signal capture when the input approaches either supply rail. The 10 MHz gain-bandwidth product supports moderate-frequency signal paths, while the 65° phase margin provides stability margin for common closed-loop gain configurations. Typical input offset voltage is 3 mV, and minimum common-mode rejection ratio is 70 dB. Typical uses include low-voltage sensor conditioning, current-loop and voltage-loop amplification, analog filtering, ADC input buffering, general-purpose instrumentation, and mixed-signal control. Combining four amplifiers in one package can also reduce board area and simplify power distribution where four matching amplifier channels are required. Designers should check input and output swing, capacitive-load stability, noise gain, and system grounding. Decoupling capacitors should be placed close to the supply pins, and unused amplifier inputs should be biased to a valid common-mode level. The extended-temperature grade is suited to industrial environments when the board, solder, and surrounding components also meet the required temperature limits. This page combines the manufacturer specifications with package-level guidance, application fit, and practical design considerations. It also distinguishes verified device characteristics from parameters that still require circuit-level confirmation, helping engineers evaluate the MCP6294-E/P before PCB implementation.

Запрос цены Контакты

MCP631-E/SN

MCP631-E/SN - 24MHz Low-Power R-R Op Amp | Microchip

The Microchip Technology MCP631-E/SN is a single, rail-to-rail-output CMOS operational amplifier with a typical gain-bandwidth product of 24 MHz, a typical slew rate of 10 V/us, and an 8-pin SOIC package. It operates from a 2.5 V single supply, targets low-power and high-speed signal processing, and provides a typical output short-circuit current of 70 mA. The -E/SN ordering option places the device in an 8-pin SOIC package and supports an operating temperature range of -40 C to +125 C. An operational amplifier, or op amp, is a high-gain analog building block that compares two input voltages and drives its output according to their difference. Within the signal-chain hierarchy, the MCP631 belongs to the CMOS operational-amplifier family and supports general-purpose amplifier, buffer, and voltage-feedback applications. Its rail-to-rail output allows the output to approach the supply limits more closely than a conventional fixed-output amplifier, improving usable signal range in low-voltage systems. The MCP631 combines a 24 MHz typical gain-bandwidth product with a 10 V/us typical slew rate, making it responsive enough for low-to-moderate-frequency filtering, buffering, and gain stages. Its typical input noise density is 10 nV/Hz at 1 MHz, while common-mode rejection reaches 78 dB. The device also features low input bias current of 0.0050 uA and is manufactured using Microchip's CMOS process for low-cost, low-power, and high-speed operation. The amplifier uses a CMOS process and provides a single amplifier in an 8-pin SOIC outline. Because its performance is specified for low-voltage operation, designers should maintain adequate input and output common-mode range at the selected supply voltage. The typical 70 mA short-circuit current indicates a useful drive capability for moderate capacitive loads, although stability and transient behavior must be evaluated for each external load and feedback network. Typical uses include low-voltage sensor conditioning, portable instrumentation, buffered analog signals, active filtering, and general signal conditioning. The MCP631-E/SN is especially suitable when a design needs more bandwidth than a micropower amplifier but does not require the drive current of a power operational amplifier. Its -40 C to +125 C rating also supports industrial temperature-range requirements. For stable operation, follow the feedback and compensation guidance in the manufacturer datasheet, place input and output decoupling capacitors close to the device, and verify stability with the intended source impedance and capacitive loading. Do not assume that rail-to-rail output eliminates output-current or common-mode limitations near the supply rails. This product page combines the manufacturer electrical characteristics with practical selection criteria, package details, comparison points, and design guidance. It highlights where the MCP631-E/SN fits within low-voltage amplifier designs and clarifies the distinctions among verified same-family drop-in options.

Запрос цены Контакты

MCP632-E/MF

MCP632-E/MF - Dual 24MHz R-R Op Amp | Microchip

Microchip Technology MCP632-E/MF is a dual CMOS operational amplifier with a typical gain-bandwidth product of 24 MHz, a typical slew rate of 10 V/us, and rail-to-rail output capability. The device is supplied in an 8-DFN exposed-pad package measuring 3 x 3 mm, making it suitable for compact signal-conditioning and instrumentation circuits. Its typical supply current is 2.5 mA per amplifier, while the specified short-circuit current is 70 mA. An operational amplifier is a voltage-gain amplifier used to amplify differential signals, buffer high-impedance sources, compare voltages, and drive downstream circuits. The MCP632 belongs to the broader operational-amplifier hierarchy, where it combines low-noise analog signal conditioning with high bandwidth and rail-to-rail output operation. Rail-to-rail output allows the amplifier to approach its supply-voltage limits more closely than a conventional fixed-output amplifier, improving dynamic range in low-voltage systems. The MCP632-E/MF provides two amplifiers in one package, a 24 MHz typical gain-bandwidth product, and a 10 V/us typical slew rate. Its typical output-voltage noise is 10 nV/Hz at 1 MHz, making it useful for signals where amplifier noise must remain below the signal of interest. The family also includes an enable or shutdown capability according to the manufacturer product information, allowing unused channels or complete amplifier sections to enter a reduced-power operating state. Each amplifier uses CMOS circuitry and provides rail-to-rail output operation. The combination of moderate supply current, high short-circuit current, and a 24 MHz bandwidth places the device between precision low-noise amplifiers and lower-cost general-purpose parts. Closed-loop gain, output loading, supply voltage, and output-capacitance tolerance determine the achievable response and stability. The exposed-pad package provides a direct thermal path into the PCB, allowing copper area beneath the device to improve heat dissipation without changing the electrical function of the pad. Typical applications include sensor-signal conditioning, portable instrumentation, low-side current measurement, analog filtering, and general-purpose dual-amplifier buffers. The dual configuration is particularly useful when two related channels must use identical amplifiers, such as differential sensing or gain stages. Its rail-to-rail output also suits low-voltage systems in which maximizing usable signal swing is more important than accepting a fixed output-voltage offset. The primary design consideration is output stability when driving capacitive loads. Feedback compensation, isolation resistors, and conservative gain settings should be selected by examining the gain-bandwidth and slew-rate behavior in the circuit. The exposed pad must be connected to the appropriate ground plane and thermal copper according to the manufacturer package guidance. Input and output traces should be kept short and separated from switching-current paths to reduce coupling and maintain the amplifier's low-noise performance. This product page combines the manufacturer family information with practical guidance on package layout, signal conditioning, bandwidth, noise, thermal management, and qualification for a direct replacement. It also identifies the limits of available drop-in cross-references so engineers can distinguish documented compatibility from assumptions based only on similar amplifier specifications.

Запрос цены Контакты

MCP632-E/SN

MCP632-E/SN - Dual 24MHz R-R Op Amp | Microchip Technology

Microchip Technology MCP632-E/SN is a dual general-purpose operational amplifier with a 24 MHz gain-bandwidth product, 10 V/µs slew rate, and rail-to-rail output in an 8-pin SOIC package. The device combines two amplifier channels, 10 nV/√Hz typical input-noise density at 1 MHz, and a typical short-circuit current of 70 mA. An operational amplifier is a voltage-feedback amplifier used to amplify, buffer, filter, or compare analog signals. The MCP632 belongs to the operational-amplifier hierarchy, where its rail-to-rail output stage allows the output voltage to approach the supply rails while maintaining a 24 MHz bandwidth. This makes the device suitable for signal-conditioning stages that require faster settling than general-purpose low-power amplifiers provide. Key performance features include a 24 MHz gain-bandwidth product and a 10 V/µs typical slew rate. The typical 1 MHz noise density is 10 nV/√Hz, while the typical short-circuit current is 70 mA. The dual-circuit configuration provides two independent amplifiers in one 8-SOIC package, reducing board area compared with two separate single operational amplifiers. The MCP63x family combines high gain bandwidth with relatively high output short-circuit capability. Because the MCP632-E/SN is packaged in 8-SOIC, it can be placed on conventional surface-mount analog boards and routed with standard dual-amplifier layouts. Its rail-to-rail output improves usable output range in low-voltage systems where output headroom is limited. Typical uses include audio preamplification, sensor signal conditioning, active filtering, comparator-style threshold circuits, and general analog signal conditioning. The 24 MHz bandwidth is particularly useful for higher-frequency sensor interfaces and low-level signal chains. Designers should still account for input common-mode limits, output drive, noise, and stability when connecting capacitive loads. For layout, place input and output decoupling capacitors close to their corresponding pins and avoid routing sensitive input traces beside high-current outputs. Use a solid ground reference and assess gain-bandwidth and phase-margin requirements when driving capacitive or highly capacitive sensor networks. Stable feedback-network placement is especially important at the device's relatively high bandwidth. This product data combines manufacturer and distributor specifications with focused engineering guidance, application analysis, package information, and verified replacement context. It helps engineers evaluate MCP632-E/SN for compact, high-speed dual analog signal-conditioning designs and compare the available drop-in option without obscuring the distinctions between amplifier families.

Запрос цены Контакты

MCP633-E/SN

MCP633-E/SN - 24MHz RRIO Op Amp | Microchip Technology

The Microchip Technology MCP633-E/SN is a single, general-purpose operational amplifier with a 24 MHz typical gain-bandwidth product, 10 V/µs typical slew rate, and rail-to-rail input and output operation. The device is packaged in an 8-pin SOIC and operates from 2.5 V to 5.5 V, making it suitable for low-voltage analog signal chains. An operational amplifier is a high-gain analog building block that compares an input signal with a feedback-defined reference and amplifies the difference between them. Within the semiconductor hierarchy, the MCP633-E/SN belongs to the operational amplifier, analog amplifier, and integrated-circuit families. Its rail-to-rail behavior supports signal acquisition and output stages that operate close to the supply rails. The MCP63x family provides high gain-bandwidth product and high output short-circuit current, while supported variants include a Chip Select control for low-power operation. For the MCP633-E/SN, key characteristics include 24 MHz typical gain-bandwidth, 10 V/µs typical slew rate, 78 dB CMRR, and a typical 70 mA output short-circuit current. These ratings support faster closed-loop response than general-purpose low-speed amplifiers. Its operating range of 2.5 V to 5.5 V accommodates 3.3 V and 5 V systems. A typical 10 nV/√Hz voltage-noise density at 1 kHz is useful for sensors and instrumentation, while the 70 mA typical short-circuit current provides drive margin for moderate capacitive and resistive loads. The 8-pin SOIC package also supports conventional surface-mount assembly. Typical uses include low-voltage sensor conditioning, active filtering, analog buffers, instrumentation, portable measurement systems, and mixed-signal signal processing. The MCP633-E/SN is particularly appropriate where a compact single amplifier, broad bandwidth, and rail-to-rail operation are required without the component count of a dual or quad amplifier. Design the feedback network for stability, keep sensitive input nodes physically short, and use decoupling capacitors close to the supply pins. Confirm the actual output-current and capacitive-load limits for the operating condition because short-circuit current is not the maximum continuous load-current rating. This page combines the manufacturer device description with practical package, application, and substitution guidance. It highlights where the MCP633-E/SN fits, which same-package alternatives require further qualification, and which layout and signal-integrity checks should be completed before production release.

Запрос цены Контакты

MCP634-E/ST

MCP634-E/ST - 24MHz Quad Rail-to-Rail Op Amp | Microchip

Microchip Technology MCP634-E/ST is a quad general-purpose operational amplifier featuring a 24 MHz gain-bandwidth product, 10 V/us slew rate, and 2.5 mA supply current. The device contains four amplifiers in a 14-pin TSSOP package and provides rail-to-rail output operation for general-purpose signal-conditioning applications. An operational amplifier is an analog integrated circuit that amplifies the difference between two input voltages. A rail-to-rail output amplifier can approach its positive or negative supply rail at its output, increasing usable output range in low-voltage systems. The MCP634-E/ST belongs to the amplifier IC hierarchy: operational amplifier, general-purpose amplifier, analog IC, and semiconductor. Its principal performance characteristics include a 24 MHz typical gain-bandwidth product, 10 V/us typical slew rate, 70 mA typical output short-circuit current, and 10 nV/Hz typical input-noise density at 1 MHz. The four amplifier sections allow multiple signal paths to be implemented in one package, reducing board area when an application does not require independent rail-to-rail input capability. The MCP63x family architecture combines high gain-bandwidth product with relatively high output short-circuit current. These characteristics make the amplifier suitable for filtering, buffering, instrumentation, and low-to-moderate-level signal amplification where fast output transitions and output-drive capability are more important than micropower operation. Typical uses include sensor-signal conditioning, analog filter stages, audio preamplification, instrumentation buffers, and general-purpose analog signal processing. The 14-TSSOP package is suitable for conventional surface-mount assembly, while the quad configuration permits four amplifier functions in one component. Design the surrounding support network with the datasheet's recommended input and output component values. Confirm output swing, input common-mode range, supply voltage, and stability requirements for the selected gain before releasing the circuit. A feedback resistor and compensation choice must also account for the intended closed-loop bandwidth. This page organizes the manufacturer's principal device characteristics into an application-oriented guide, adds practical implementation guidance, clarifies replacement constraints, and supports direct sourcing through the Request a Quote form on this page.

Запрос цены Контакты

MCP635-E/MF

MCP635-E/MF - Dual 24MHz Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP635-E/MF is a dual operational amplifier with a typical gain-bandwidth product of 24 MHz, 63 dB minimum common-mode rejection, and a 10 V/µs typical slew rate in a 10-DFN surface-mount package. Designed for low-voltage signal conditioning, the amplifier provides rail-to-rail output operation and is identified as an automotive-grade AEC-Q100 device. An operational amplifier is an analog signal-processing IC that amplifies the voltage difference between its two inputs. Within the broader power-management and semiconductor hierarchy, a dual rail-to-rail op amp combines two amplifier channels in one package. Rail-to-rail output capability allows the output voltage to approach the available supply rails, improving output range in compact low-voltage systems. The MCP635-E/MF offers a typical 24 MHz gain-bandwidth product, 10 nV/√Hz input noise at 1 MHz, 10 V/µs slew rate, and 8 mV input-offset voltage. Its minimum common-mode rejection ratio of 63 dB helps suppress common-mode interference. The dual configuration reduces package count when two independent gain stages, active filters, or buffer functions are required. Its CMOS architecture supports low-voltage operation and rail-to-rail output behavior. The exposed-pad 10-DFN package provides a compact footprint and an efficient thermal path when copper area is used correctly. With a typical operating current of 85 mA and typical short-circuit current of 70 mA, the device is suited to signal paths that require moderate bandwidth without the size of a discrete implementation. Typical applications include instrumentation front ends, sensor conditioning, active filters, audio and communications buffers, and low-voltage control systems. The dual channels can implement matched gain stages, buffers, or active filters when signal symmetry and PCB area are priorities. Its 24 MHz bandwidth is particularly useful for instrumentation and intermediate-frequency signal chains requiring higher slew rate than general-purpose amplifiers. Place input and output decoupling capacitors close to their corresponding pins, route sensitive input traces away from switching nodes, and connect the exposed thermal pad to a solid ground or thermal plane. Confirm output-current limits, supply voltage, stability requirements, and operating temperature before finalizing the analog section. This page combines the key electrical characteristics, application guidance, package considerations, and verified replacement information for engineers evaluating the MCP635-E/MF in compact dual-amplifier designs.

Запрос цены Контакты

MCP6491T-E/LTY

MCP6491T-E/LTY - 7.5MHz Low-Bias Op Amp | Microchip

The Microchip MCP6491T-E/LTY is a single, rail-to-rail input and output operational amplifier with a typical gain-bandwidth product of 7.5 MHz, typical low input bias current of 150 pA at 125°C, and operation from a single supply as low as 2.4 V. It is packaged in the compact 5-pin SC-70 package and offered in tape-and-reel packaging. The device is unity-gain stable, making it suitable for low-power signal conditioning when both source impedance and stability requirements are considered. An operational amplifier, or op amp, is a voltage-controlled differential amplifier used to amplify, buffer, filter, compare, or reshape analog signals. Within the broader semiconductor hierarchy, this product is an analog integrated circuit, specifically a general-purpose CMOS operational amplifier. Rail-to-rail input operation helps the amplifier accept signals near its supply rails, while rail-to-rail output operation extends usable output swing toward the rails. The low input bias current makes the MCP6491 family useful with high-impedance sources where amplifier input current can materially affect accuracy. The MCP6491 family combines a typical 7.5 MHz gain-bandwidth product with low power consumption. According to the Microchip manufacturer page, the devices draw a typical 530 µA per amplifier, support single-supply operation from 2.4 V, and provide rail-to-rail input and output behavior. The manufacturer datasheet states that the MCP6491/MCP6492/MCP6494 family uses an advanced CMOS process and is specified over an extended temperature range from -40°C to +125°C. The MCP6491T-E/LTY is a single-amplifier device, whereas MCP6492 and MCP6494 provide dual and quad versions respectively. Unity-gain stability supports direct use as a voltage follower, but board-level stability still depends on output capacitive load, feedback topology, operating voltage, and the surrounding source and load impedances. The low typical input bias current is particularly relevant when driving the input from sensors, photodiodes, resistive dividers, or other high-output-impedance sources. Typical applications include low-power sensor signal conditioning, current-monitoring front ends, battery-powered instrumentation, portable measurement systems, analog filtering, and general-purpose signal buffering. The 5-pin SC-70 package supports compact layouts, but users should follow the manufacturer datasheet for land patterns, exposed-pad or lead information, and assembly guidelines. Designers should verify supply voltage limits, input common-mode range, output swing, output-drive capability, noise, offset voltage, and load stability in the manufacturer datasheet. A bypass capacitor close to the supply pins is generally important for clean operation, while input and feedback resistors should be selected to control bias-current error and preserve the required bandwidth. This product page consolidates the verified Microchip specifications, distributor availability information, package details, and design considerations. It is intended to support component selection and board-level planning without guessing electrical limits that are not explicitly provided in the verified source material.

Запрос цены Контакты

MCP652-E/SN

MCP652-E/SN - 50MHz Dual Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP652-E/SN is a dual operational amplifier with a typical gain-bandwidth product of 50 MHz, rail-to-rail output, 30 V/us slew rate, and low 7.5 nV/Hz input-noise density. It is packaged as an 8-pin SOIC and specified for operation from -40C to +125C. The MCP652-E/SN also uses Microchip's mCal self-calibration technology to reduce input-offset voltage during power-up. An operational amplifier, or op amp, is a high-gain analog building block used to amplify small signals, buffer sensors, compare voltages, and drive analog-to-digital converters. The MCP652-E/SN belongs to the MCP65x family of low-offset, high-speed, low-noise amplifiers. It combines single-supply operation, rail-to-rail output, low distortion, and self-calibration in an 8-pin SOIC footprint suitable for general-purpose analog signal chains. Key electrical characteristics include a 50 MHz typical gain-bandwidth product, 30 V/us typical slew rate, 81 dB typical common-mode rejection, and a calibrated input-offset-voltage limit of +/-200 uV. The 7.5 nV/Hz typical noise density is particularly useful when small signals must be amplified without adding excessive broadband noise. The dual configuration provides two amplifiers in one package, reducing board area in filtering, buffering, and differential signal-conditioning circuits. The MCP65x architecture performs self-calibration at power-up to lower input-offset voltage. This calibration is valuable in precision applications because input offset can otherwise create DC error, shift comparator thresholds, or reduce the effective resolution of an ADC. The rail-to-rail output allows the amplifier to approach the supply limits when higher output swing or wider signal range is required, although input-common-mode limits must still be checked for each operating condition. Typical uses include sensor signal conditioning, active filters, audio and communication paths, ADC drivers, comparators, and low-voltage instrumentation. The dual configuration is especially useful when a design needs two gain stages, a filter followed by an ADC driver, or an instrumentation amplifier built from matched amplifiers. The -40C to +125C temperature range supports industrial environments, while the standard 8-pin SOIC package simplifies assembly and board-level sourcing. The principal design trade-off is operating speed versus power and stability. High gain-bandwidth and slew rate support faster signal transitions, but feedback networks, capacitive loads, decoupling, and output-current limits still require careful review. Place bypass capacitors near the supply pins, keep feedback loops compact, and verify stability with the actual source and load impedances before releasing the layout. This product page combines manufacturer specifications, package and temperature details, application guidance, and same-footprint family comparisons to support component selection, schematic design, PCB layout, and replacement planning for the MCP652-E/SN.

Запрос цены Контакты

MCP654-E/SL

MCP654-E/SL - 50MHz Quad Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP654-E/SL is a four-circuit, rail-to-rail operational amplifier with a 50 MHz gain-bandwidth product, 200 uV offset voltage, and operation down to 1.8 V, housed in a 14-pin SOIC package. The four amplifiers are intended for general-purpose signal conditioning, and their rail-to-rail inputs and outputs support operation close to the supply rails. An operational amplifier is a voltage-controlled, high-gain analog building block used to amplify, buffer, filter, compare, or shape signals. The MCP654-E/SL belongs to the amplifier hierarchy of operational amplifier, analog IC, and semiconductor. Its mCal startup calibration can reduce input-referred offset by measuring and correcting the amplifier offset after power-up, helping improve accuracy in instrumentation and precision analog signal chains. The principal features include four amplifiers per package, a 50 MHz gain-bandwidth product, rail-to-rail input and output operation, and a minimum operating supply voltage of 1.8 V. These characteristics make the device useful for low-voltage sensor conditioning, audio signal paths, communications interfaces, and general-purpose analog processing. The 14-pin SOIC package also supports conventional surface-mount PCB assembly. The MCP65x family combines low offset, low bias current, and self-calibration using mCal. According to the manufacturer product page, at power-up the operational amplifiers are self-calibrated, while selected package options provide a calibration or chip-select pin for low-power operation. The MCP654-E/SL combines these calibration features with a quad-amplifier arrangement, allowing four similar signal paths to share one package without requiring four separate devices. Typical uses include buffering sensor outputs, amplifying low-level analog signals, active filtering, audio preamplification, and communications line-interface circuits. Its low 1.8 V minimum supply operation is especially useful in battery-powered equipment, while the 50 MHz gain-bandwidth product supports wider-bandwidth closed-loop designs than low-frequency precision amplifiers. For PCB implementation, use the manufacturer pin-description table when assigning tracks and power connections. Decoupling capacitors should be placed close to the supply pins, and sensitive analog inputs should remain away from switching nodes. Verify stability with the selected gain, load capacitance, and output-driving network before finalizing the layout. This page organizes the key operating characteristics, package information, application guidance, and verified drop-in comparisons for engineers evaluating the MCP654-E/SL. It also distinguishes practical selection factors such as calibration behavior, channel count, bandwidth, voltage range, and footprint compatibility.

Запрос цены Контакты

MCP655-E/MF

MCP655-E/MF - Dual 50MHz R-R Op Amp | Microchip Technology

The Microchip Technology MCP655-E/MF is a dual general-purpose operational amplifier with rail-to-rail input and output capability, a 50 MHz gain-bandwidth product, and a 30 V/us slew rate. It operates from 2.5 V to 5.5 V and is packaged in a 10-pin DFN package with an exposed pad. The device is supplied in tube packaging under the MCP655-E/MF ordering code. An operational amplifier is a high-gain analog signal-conditioning IC used to amplify, buffer, compare, and filter voltages. The MCP655-E/MF belongs to the MCP65x family of rail-to-rail amplifiers with mCal calibration. Within the product hierarchy, it is an operational amplifier, analog amplifier, and signal-conditioning IC used in electronic control, measurement, and interface systems. The two amplifiers provide 50 MHz gain-bandwidth product and 30 V/us slew rate, allowing the devices to process higher-frequency signals than general-purpose low-speed amplifiers. Rail-to-rail input and output operation improves dynamic range in low-voltage systems where the useful signal can approach either supply rail. The manufacturer identifies a typical low offset of 200 uV and a supply current of 6 mA for this amplifier family. The MCP65x devices use mCal to self-calibrate at power-up, reducing initial offset error without requiring a separate trimming procedure. Package options with a calibration or chip-select function can also support low-power operation and scheduled offset calibration. The exposed thermal pad provides a low-impedance path for heat removal, but its effectiveness depends on the PCB thermal design and the copper area connected to the pad. Typical uses include sensor signal conditioning, current measurement, active filtering, audio and communication interfaces, and low-voltage embedded control. The MCP655-E/MF is particularly suitable for compact designs that require two high-speed amplifiers and rail-to-rail signal handling without the larger footprint of a traditional dual SOIC. When laying out the circuit, place input and output decoupling capacitors close to their associated supply pins and connect the exposed pad to a ground plane with thermal vias. Confirm input and output common-mode limits, output-current capability, and capacitive-load stability against the manufacturer datasheet for the selected operating conditions. This product page combines manufacturer-level operating details, package information, application guidance, comparison parameters, and practical layout notes to support faster component selection and PCB implementation.

Запрос цены Контакты

MCP659-E/ML

MCP659-E/ML - 50MHz Quad Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP659-E/ML is a quad operational amplifier with four amplifier circuits, rail-to-rail input and output capability, a 50 MHz typical gain-bandwidth product, and a 16-QFN 4 x 4 mm package. It is designed for general-purpose signal conditioning applications that require low offset and a compact package. The device also uses Microchip mCal technology to self-calibrate at power-up, helping reduce input-offset voltage and improve precision in applications where amplifier matching and DC accuracy are important. Operational amplifiers are active semiconductor devices that amplify the difference between two input voltages. They are used within analog signal chains, including sensor interfaces, filtering, instrumentation, buffering, and control systems. The MCP659-E/ML belongs to the MCP65x family of low-offset operational amplifiers and combines four amplifiers in one quad package. Its rail-to-rail input and output structure allows operation near the supply rails, while the 50 MHz bandwidth supports higher-frequency signal paths than low-bandwidth precision amplifiers. Key characteristics include a typical gain-bandwidth product of 50 MHz, typical slew rate of 30 V/us, typical short-circuit current of 100 mA, and typical voltage-noise density of 7.5 nV/sqrt(Hz) at 1 MHz. The calibrated input offset is specified at a maximum of ±200 uV. The operating temperature range is -40 C to +125 C. The MCP659-E/ML is supplied in a 16-QFN package, with an exposed-pad package designation associated with the -ML ordering code. The mCal function is particularly relevant to precision dc applications because it performs an offset-calibration sequence at power-up. The manufacturer datasheet also notes that some MCP65x package options include a calibration/chip-select pin for low-power operation and offset calibration. Designers should review the exact pin configuration, timing requirements, and calibration behavior for the selected package before laying out the PCB. Typical uses include industrial sensor conditioning, portable measurement systems, low-noise analog front ends, instrumentation, and multi-channel signal acquisition. When designing around the MCP659-E/ML, provide stable bypassing close to the supply pins, account for amplifier stability with the selected feedback network and load capacitance, and verify that the operating voltage and temperature remain within the device ratings. This product page organizes the manufacturer information, datasheet references, package details, application guidance, and qualification questions for engineers evaluating the MCP659-E/ML. The MCP659 family is presented as a general-purpose, four-circuit rail-to-rail operational-amplifier solution with mCal-enabled offset calibration.

Запрос цены Контакты

MCP660-E/ML

MCP660-E/ML - 60MHz Triple RRO Op Amp | Microchip

The Microchip Technology MCP660-E/ML is a triple general-purpose operational amplifier with a typical gain-bandwidth product of 60 MHz, typical slew rate of 32 V/us, and rail-to-rail output capability in a 16-VQFN exposed-pad package measuring 4 x 4 mm. The device also provides a typical output short-circuit current of 90 mA and typical input-voltage noise density of 6.8 nV/Hz at 1 MHz. An operational amplifier is an analog signal-conditioning semiconductor that compares its inverting and non-inverting inputs and amplifies the voltage difference between them. Operational amplifiers belong to the linear-amplifier hierarchy, support closed-loop gain and feedback configurations, and are widely used in sensor interfaces, filters, buffers, signal conditioners, and control systems. Rail-to-rail output capability allows the MCP660-E/ML to approach its supply limits under suitable load conditions. The MCP660-E/ML combines three amplifiers in one package, making it useful when a board requires multiple high-speed signal paths and limited footprint area. Its 60 MHz gain-bandwidth product supports higher closed-loop bandwidth than lower-frequency general-purpose amplifiers. The 32 V/us slew rate provides faster edge rates for moderate-amplitude signals, while the 90 mA typical output short-circuit current indicates substantial output-drive capability for its class. The amplifier family is optimized for high-speed applications and includes variants with Chip Select support for low-power operation, according to the Microchip MCP660 product page. The MCP660-E/ML is identified as the E-temperature, tube-packaged member of the MCP660 family. Its exposed-pad package provides a direct thermal path from the device to the PCB, making copper-plane design and thermal verification important in compact, high-output-current implementations. Typical uses include multi-channel sensor conditioning, active filtering, buffered analog inputs, communications-interface signal conditioning, and precision control or measurement circuits. Three integrated channels can reduce component count when several independent low- or moderate-amplitude signals must be conditioned. For applications involving high output current, capacitive loading, or sustained full-bandwidth operation, verify drive capability and thermal performance in the final circuit rather than relying only on typical short-circuit-current figures. Place input and output components close to the associated amplifier pins, route high-current return paths through the exposed pad and surrounding copper, and keep sensitive input traces away from switching nodes. Use the manufacturer pin-description table and recommended decoupling arrangement when assigning PCB nets. The exposed pad must be connected according to the package drawing, and its thermal performance depends on the available copper area. This product page combines the confirmed 60 MHz bandwidth, 32 V/us slew rate, 90 mA typical short-circuit current, 6.8 nV/Hz noise density, package information, application guidance, and qualification-aware comparison notes to support faster component selection and board-level planning.

Запрос цены Контакты

MCP660-E/SL

MCP660-E/SL - 60MHz Triple R-R Op Amp | Microchip Technology

The Microchip Technology MCP660-E/SL is a general-purpose, rail-to-rail-output operational amplifier containing three independent amplifier circuits in a 14-pin SOIC package. Its headline specifications include a 60 MHz typical gain-bandwidth product, a 32 V/µs typical slew rate, and operation from 2.5 V to 5.5 V. The device is intended for low-voltage signal-conditioning systems requiring three amplifiers on one board footprint. An operational amplifier is an active semiconductor device that uses high-gain differential amplification to strengthen signals applied between its inverting and non-inverting inputs. Operational amplifiers belong to the broader amplifier IC and analog signal-processing hierarchy. They commonly perform buffering, current-to-voltage conversion, voltage amplification, active filtering, comparison, and feedback-controlled functions in instrumentation, communications, industrial control, and consumer electronics. The MCP660-E/SL combines a 60 MHz typical gain-bandwidth product with rail-to-rail output capability. Its typical slew rate is 32 V/µs, allowing comparatively large voltage changes to occur quickly. Other stated characteristics include 6.8 nV/√Hz typical output noise at 1 kHz, 1.8 mV typical input offset voltage, 10 pA typical input bias current, 81 dB typical open-loop gain, 90 mA typical output short-circuit current, and 6 mA typical supply current. The MCP660 family uses a CMOS-compatible design optimized for high-speed general-purpose applications. Because the amplifiers include rail-to-rail outputs, they can drive loads near the supply rails more effectively than conventional fixed-output amplifier stages. The 60 MHz bandwidth is particularly useful when the design must preserve the frequency content of signals beyond the audio range, while the 32 V/µs slew rate helps minimize large-signal distortion. Typical applications include sensor-signal conditioning, active audio paths, portable measurement equipment, analog filtering, data acquisition, and low-voltage control systems. Because the MCP660-E/SL contains three amplifiers, it can implement a complete three-channel conditioning or filtering block without requiring three separate amplifier packages. The 14-SOIC format also supports conventional surface-mount assembly. Designers should account for the device’s 2.5 V to 5.5 V operating range and provide adequate supply bypassing at each amplifier’s supply pins. Decoupling capacitors should be placed close to the package power pins, while input and feedback components should be positioned to minimize parasitic capacitance and unwanted coupling between the three amplifier channels. This page combines the manufacturer’s device characteristics with practical guidance for PCB implementation, application suitability, and replacement evaluation. It also distinguishes verified electrical and environmental attributes from unspecified details so engineers can assess fit, signal bandwidth, thermal limits, and board compatibility before incorporating the MCP660-E/SL into a production design.

Запрос цены Контакты

MCP660-E/ST

MCP660-E/ST - 60MHz Triple Rail-to-Rail Op Amp, 14-TSSOP | Microchip

The Microchip Technology MCP660-E/ST is a triple general-purpose operational amplifier with a 60 MHz gain-bandwidth product, 32 V/us slew rate and rail-to-rail output, packaged in a 14-pin TSSOP and specified for a 2.5 V to 5.5 V single supply. It is offered in the extended (-40 C to +125 C) temperature grade for industrial and automotive-adjacent designs. An operational amplifier (op amp) is a differential-input, high-gain active device that amplifies the difference between two input voltages. It sits in the signal path between a sensor or source and a downstream load such as an ADC, a filter, or a feedback control loop. The MCP660 belongs to the broader CMOS operational amplifier family, which divides into precision amplifiers, low-noise amplifiers, high-speed amplifiers, and general-purpose amplifiers. Because the MCP660 is specified for a 2.5 V to 5.5 V supply, it belongs to the low-voltage class that dominates portable, sensor-node, industrial instrumentation, and signal-conditioning equipment. Key features of the MCP660 include three amplifiers in one package, a 60 MHz gain-bandwidth product that supports closed-loop operation well into the megahertz range, a 32 V/us slew rate that preserves large-signal fidelity on fast edges, and rail-to-rail output swing that maximises usable output range in low-voltage designs. Microchip describes the MCP66x family as optimised for high speed and featuring high output short-circuit current, which gives strong drive into light capacitive and resistive loads. A single package containing three channels also reduces board area and simplifies multi-axis, multi-channel, or multi-filter designs. Architecturally the part is a CMOS operational amplifier with a high gain-bandwidth product and rail-to-rail output stage, intended for general-purpose signal conditioning rather than precision DC measurement. The 32 V/us slew rate and 60 MHz bandwidth make it suitable for active filters, audio preamplification, sensor buffering, and instrumentation where the signal bandwidth exceeds that of typical micropower amplifiers, while the low minimum supply voltage of 2.5 V allows direct operation from single-cell and 3.3 V rails. Typical applications include active low-pass and band-pass filters for sensor conditioning, audio and microphone preamplifier stages, buffer stages ahead of ADCs, communications and line-driver receive paths, and general instrumentation front ends where multiple channels must be matched for common-mode and bandwidth behaviour. The triple configuration is especially useful when three axes of a measurement or three filters of a signal chain must share supply and layout characteristics. When designing with the MCP660-E/ST, pay attention to stability when driving capacitive loads: place output decoupling close to the supply pins, keep feedback networks compact, and confirm gain stability with the actual load. Because the amplifier is rail-to-rail at the output, the input common-mode range versus output swing should be checked against the datasheet curve for the specific supply voltage. The extended temperature grade also demands attention to DC bias drift when the amplifier is used as a precision DC buffer. This page consolidates channel count, bandwidth, slew rate, supply range, package and temperature-class information for the MCP660-E/ST, adds pin-level detail, package-and-footprint-compatible alternatives, parameter-by-parameter comparison, and practical design notes that are not presented together on a manufacturer datasheet landing page.

Запрос цены Контакты

MCP662-E/MS

MCP662-E/MS - Dual 60 MHz Rail-to-Rail Op Amp | Microchip

The Microchip Technology MCP662-E/MS is a dual, general-purpose operational amplifier with a 60 MHz gain-bandwidth product, rail-to-rail output, and an 8-pin MSOP package. It is designed for signal-conditioning applications requiring two amplifiers on one board and operating from a 5.5 V maximum supply. An operational amplifier, or op amp, is an analog semiconductor that amplifies the voltage difference between its inverting and non-inverting inputs. A dual op amp contains two amplifier channels in one package, reducing board area and simplifying common supply and ground connections. Within the broader hierarchy, the MCP662-E/MS is a rail-to-rail amplifier, analog IC, and general-purpose signal-conditioning component. The 60 MHz gain-bandwidth product makes the MCP662-E/MS suitable for higher-frequency feedback networks, including video, communications, instrumentation, and active filtering. Rail-to-rail output operation improves output-voltage range utilization, while the dual-channel configuration supports complementary signal paths or two independent channels. The -E suffix identifies an extended-temperature product, while /MS denotes the 8-pin MSOP packaging used by the MCP662 family. Microchip describes the MCP66x family as featuring high gain-bandwidth product and high output short-circuit current. Those characteristics support low-impedance drive of downstream circuitry and operation in feedback systems where closed-loop bandwidth is more important than static offset or noise alone. Because op-amp performance depends on supply voltage, output loading, feedback topology, and external components, practical bandwidth should be evaluated in the final circuit rather than inferred solely from the gain-bandwidth figure. Typical uses include active filters, sensor-conditioning stages, communications interfaces, video signal chains, audio buffers, and general instrumentation. The two channels may drive successive filter stages, process complementary signals, or implement a small closed-loop amplifier when appropriate feedback resistors are selected. Its MSOP package also supports compact designs where analog performance and routing density are both important. When laying out the circuit, place input and feedback components close to the amplifier pins to minimize parasitic capacitance and feedback-loop area. Keep sensitive input nodes away from high-current output paths, provide adequate supply bypassing, and verify stability with realistic source impedance, load capacitance, and output-drive requirements before committing the layout. This product page combines manufacturer-device information, distributor listings, package and pinout guidance, drop-in same-family alternatives, and practical circuit-design considerations to support component selection and PCB implementation.

Запрос цены Контакты

Подкатегории

Товары (39.000+)

MCP625-E/MF - 20MHz Dual Rail-to-Rail Op Amp | Microchip

MCP6272-E/P - Dual 2MHz RRO Op Amp | Microchip

MCP6273-E/P - 2 MHz Rail-to-Rail Op Amp | Microchip

MCP6274-E/P - 2 MHz Rail-to-Rail Quad Op Amp | Microchip Technology

MCP6283-E/P - 5MHz Dual RRIO Op Amp | Microchip

MCP629-E/ML - 20 MHz Quad Rail-to-Rail Op Amp | Microchip

MCP6291-E/P - 10MHz RAIL-to-Rail Op Amp | Microchip

MCP6293-E/P - 10MHz Low-Power R-R Op Amp | Microchip

MCP6294-E/P - Quad 10MHz RRIO Op Amp | Microchip

MCP631-E/SN - 24MHz Low-Power R-R Op Amp | Microchip

MCP632-E/MF - Dual 24MHz R-R Op Amp | Microchip

MCP632-E/SN - Dual 24MHz R-R Op Amp | Microchip Technology

MCP633-E/SN - 24MHz RRIO Op Amp | Microchip Technology

MCP634-E/ST - 24MHz Quad Rail-to-Rail Op Amp | Microchip

MCP635-E/MF - Dual 24MHz Rail-to-Rail Op Amp | Microchip

MCP6491T-E/LTY - 7.5MHz Low-Bias Op Amp | Microchip

MCP652-E/SN - 50MHz Dual Rail-to-Rail Op Amp | Microchip

MCP654-E/SL - 50MHz Quad Rail-to-Rail Op Amp | Microchip

MCP655-E/MF - Dual 50MHz R-R Op Amp | Microchip Technology

MCP659-E/ML - 50MHz Quad Rail-to-Rail Op Amp | Microchip

MCP660-E/ML - 60MHz Triple RRO Op Amp | Microchip

MCP660-E/SL - 60MHz Triple R-R Op Amp | Microchip Technology

MCP660-E/ST - 60MHz Triple Rail-to-Rail Op Amp, 14-TSSOP | Microchip

MCP662-E/MS - Dual 60 MHz Rail-to-Rail Op Amp | Microchip