Драйверы светодиодов
Товары (9)
ICM7228AIPA - 8-Digit LED Display Decoder Driver | Renesas
The Renesas (formerly Intersil) ICM7228AIPA is an 8-digit, microprocessor-compatible, LED display decoder driver housed in a 28-pin PDIP (Plastic DIP) package. The device integrates two types of 7-segment decoders, multiplex scan circuitry, LED segment drivers, LED digit drivers, and an 8-byte display memory on a single CMOS die, enabling a single-chip interface between a microprocessor and a multiplexed 8-digit common-cathode or common-anode 7-segment LED display. LED display decoder drivers are specialized interface ICs that bridge a parallel or serial microprocessor bus and a multiplexed 7-segment LED panel. Within the broader system hierarchy, an LED driver sits between the MCU/microprocessor and the human-machine interface (HMI) layer; it removes the burden of segment multiplexing and brightness control from the host firmware, freeing the MCU for primary tasks. The ICM7228 family is a classic example of a self-contained display controller that requires only a few external current-limiting resistors and bypass capacitors. Key features of the ICM7228AIPA include on-chip 7-segment decoders supporting both hexadecimal (A version) and code-B (B version) character sets, an integrated multiplex scanner that sequentially enables each of the 8 digit positions, segment and digit drivers capable of sourcing/sinking the segment current required for typical LED displays, an 8-byte internal display RAM accessed through a standard microprocessor interface, and a wide operating supply range of typically 4 V to 6 V with CMOS low-power consumption. The PDIP-28 package simplifies prototyping and hand-soldered rework compared with surface-mount equivalents, making the part attractive for industrial front-panel and instrumentation applications. The ICM7228AIPA architecture combines a parallel write interface, an 8 x 8-bit display RAM, BCD/hex decoding logic, and high-current CMOS outputs that drive both the segment lines and the digit select lines. By integrating these functions in one chip, the part eliminates dozens of discrete components and reduces software overhead, while its CMOS construction keeps quiescent current low enough for always-on industrial front panels. Typical applications include industrial control panel indicators, test and measurement front-panel readouts, point-of-sale terminals, process-control HMI displays, audio equipment VU/channel displays, and digital instrumentation meters. The wide operating range and CMOS logic compatibility make the ICM7228AIPA especially suitable for 5 V-based microprocessor boards such as legacy 8051, Z80, and similar MCU systems. When designing with this part, ensure segment current-limiting resistors are calculated against the chosen LED forward voltage and digit duty cycle, and add a 0.1 µF decoupling capacitor close to VDD. Because the part drives multiplexed digits, peak segment current can be roughly 8x the average; size the resistors accordingly to avoid exceeding absolute maximum digit current ratings. This page synthesizes Renesas/Intersil datasheet specifications, distributor stock and pricing, and pin-compatible drop-in alternatives in a format not found on the manufacturer datasheet alone.
LT3791IFE#PBF - 60V 4-Switch Sync Buck-Boost LED Driver | ADI
The LT3791IFE#PBF is a synchronous 4-switch buck-boost LED driver controller from Analog Devices, designed to regulate LED current up to 52V with input voltages above, below, or equal to the output voltage. Housed in a 38-pin TSSOP-EP package, this controller operates from a 4.7V to 60V input range and supports constant-frequency, forced-continuous current mode architecture with adjustable frequency from 200kHz to 700kHz. It provides analog and PWM dimming, making it suitable for high-power LED lighting applications. A buck-boost LED driver controller is a power management IC that regulates current through an LED string by stepping up or stepping down the input voltage as needed. Unlike a simple buck or boost converter, the 4-switch topology allows seamless transition between modes, ensuring stable LED current even when the input voltage fluctuates around the output voltage. This makes it ideal for automotive, industrial, and architectural lighting where input voltage variations are common. Key features include a wide 4.7V to 60V input range, output voltage up to 52V, and the ability to drive high-power LEDs with efficiency exceeding 95%. The controller integrates four external MOSFET drivers, supports spread spectrum for low EMI, and includes protection features such as overvoltage, overcurrent, and thermal shutdown. Its constant-frequency operation simplifies EMI filtering and allows synchronization to an external clock. The LT3791 uses a current mode control architecture with a precision reference, enabling accurate LED current regulation. The forced-continuous mode ensures low output ripple and predictable operation across all load conditions. The device also features a low supply current of 4000uA, making it efficient for battery-powered applications. Typical applications include automotive LED headlights, industrial high-bay lighting, architectural lighting, and general-purpose constant-current LED drivers. Its wide input range and buck-boost capability make it versatile for systems with varying supply voltages, such as those powered by batteries or solar panels. When designing with the LT3791, ensure proper PCB layout with short, low-inductance paths for the switching nodes and adequate thermal management for the external MOSFETs. The exposed pad on the TSSOP-EP package should be soldered to a large copper area for heat dissipation.
MAX7219EWG+T - Serially Interfaced 8-Digit LED Display Driver | ADI
The Analog Devices (formerly Maxim Integrated) MAX7219EWG+T is a compact, serial input/output, common-cathode LED display driver that interfaces microprocessors or microcontrollers to 7-segment numeric LED displays of up to 8 digits, bar-graph displays, or 64 individual LEDs, supplied in a 24-pin SOIC (Wide, 7.5 mm body) package on tape-and-reel. An LED display driver is an integrated circuit that takes low-current logic-level signals from a host controller and multiplexes them to drive a much larger array of discrete LEDs with the segment currents and refresh timing required for flicker-free human-vision operation. Inside the broader hierarchy of power management and display driver ICs, the MAX7219 belongs to the LED driver category, which itself sits under display drivers and interface ICs. Built on a CMOS process with on-chip BCD Code-B decoders, digit multiplexers, and an 8x8 static RAM scratchpad, the device replaces the bulky resistors, BCD-to-7-segment ICs, and external multiplexers that older designs required. Key specifications include a single 5 V (typical, 4.0 V minimum to 5.5 V maximum) supply rail, segment drive current adjustable from approximately 2 mA to 40 mA through a single external resistor at the ISET pin (Radix-Digit drive of 320 mA per digit at 100% duty), 16-step digital brightness control via the duty cycle, 3-wire SPI/QSPI/MICROWIRE-compatible serial interface, and a built-in BCD decoder plus seven-segment decoder with 7-segment font plus decimal-point support. The MAX7219EWG is the extended-industrial / 0 C to +70 C version of the part; the MAX7219ENG variant is offered in a 24-pin PDIP. The on-chip error mode includes a Watchdog timer, scan-limit register, blanking, and segment-on/off commands that allow a host MCU to detect and clear faults without external glue logic. Typical applications include industrial control panels with 8-digit numeric readouts, scoreboards, instrumentation front panels, point-of-sale terminals, Arduino/Raspberry-Pi-driven 7-segment matrix displays, and bar-graph or LED dot-matrix meters. The 24-pin SOIC package with 0.300 inch body width is friendly to hand-soldered prototypes and to reflow production, and the internal multiplex oscillator means the host MCU does not have to manage refresh timing. Engineering note: when stacking cascaded MAX7219 chains on long SPI lines, observe 50 ns tCP clock rise/fall limits and provide proper decoupling (10 uF + 0.1 uF) within 5 mm of the V+ pin to keep spike-induced register corruption out of the picture. This page consolidates the manufacturer datasheet with real-time distributor pricing, drop-in compatible alternatives, and practical design notes not found in the official datasheet PDF.
MCP1643-I/MC - 550mA Sync Boost LED Driver, 1MHz | Microchip
The Microchip Technology MCP1643-I/MC is a 550 mA synchronous step-up (boost) LED constant-current driver housed in an 8-pin DFN (2x3 mm) package, switching at a fixed 1 MHz frequency from a 0.65 V to 5 V input. It is the lowest-startup-voltage synchronous boost LED regulator in its class and is optimized to drive one high-brightness LED (or two series red/green/yellow LEDs) from one- and two-cell alkaline, NiMH or NiCd batteries. The 0.65 V cold-start capability allows direct operation from a single depleted alkaline cell, making it uniquely suited to primary-cell lighting applications where boost regulators from competitors fail to start. A boost (step-up) converter is a switched-mode DC-DC topology that produces an output voltage higher than its input by storing energy in an inductor during the switch-on period and releasing it into the output capacitor through a rectifier during switch-off. Synchronous rectification replaces the external Schottky diode with an internal low-side MOSFET, improving efficiency at light loads and reducing solution size - critical for portable lighting applications where every microwatt counts. The MCP1643 family adds constant-current regulation on top of the boost topology, so LED brightness remains stable as the battery droops or as the LED forward voltage changes with temperature. Key features include a 550 mA switch current limit, an integrated low-side synchronous switch, 0.65 V input startup voltage, fixed 1 MHz PWM operation, built-in over-temperature protection, and PWM duty-cycle brightness control on the EN/PWM pin. The 8-pin DFN package (2x3 mm) keeps the PCB footprint extremely small, allowing this regulator to fit inside an LED flashlight head or a wearable indicator. The internal architecture combines a current-mode PWM control core, an N-channel high-side switch, an N-channel synchronous low-side switch, an internal bandgap reference, and a feedback loop that regulates peak switch current - delivering constant LED brightness even as battery voltage drops below the LED forward voltage. The 1 MHz switching frequency allows the use of a tiny 4.7 uH inductor and small ceramic capacitors. Typical applications include LED flashlight drivers, portable backlight drivers for LCD displays, wearable device indicators, emergency lighting, and battery-powered signage. The wide 0.65 V to 5 V input range makes the device directly compatible with single-cell alkaline, single-cell NiMH, two-cell alkaline, and even USB/Li-ion sources through a simple resistive divider. When designing with the MCP1643-I/MC, select a 4.7 uH inductor with low DCR and a saturation current above 1 A, place input/output ceramics close to the IC, and use the EN/PWM pin for brightness dimming with a 100 Hz to 1 kHz PWM signal. The exposed pad must be soldered to a grounded copper pour for thermal dissipation. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet.
PCA9685PW,112 - 16-Channel 12-bit I2C LED Controller | NXP
The NXP Semiconductors PCA9685PW,112 is a 16-channel, 12-bit PWM Fm+ I2C-bus LED controller housed in a 28-pin TSSOP package. Each of the 16 outputs provides programmable 12-bit (4096-step) PWM resolution at frequencies from approximately 24 Hz to 1526 Hz, with a 25 mA sink/source capability per channel designed for voltage-switch LED driving. The device targets Red/Green/Blue/Amber (RGBA) color-mixing backlights as well as general-purpose PWM loads such as servos, fans, and status LEDs. An LED driver (or LED controller) is a semiconductor device that converts a logic-level control signal into a high-current drive suitable for lighting elements. The PCA9685 belongs to the I2C-controlled multi-channel LED driver subcategory, which sits inside the broader power-management IC family. By integrating 16 independently addressable PWM channels, an I2C interface (with up to 1 MHz Fm+ speed), and programmable output frequency, the part eliminates the need for a high-pin-count MCU or multiple discrete drivers when designing matrix backlights or animation systems. Key features include 16 totem-pole outputs (each capable of 25 mA sink), an external clock input option to synchronize multiple PCA9685 devices, 6 hardware-selectable I2C addresses (expandable to 126 with software reset), and an output enable pin for hardware blanking. Each output has its own 12-bit resolution fixed-frequency PWM controller operating from a programmable frequency typically between 24 Hz and 1526 Hz with an adjustable duty cycle from 0% to 100% (including full on/off). The internal architecture combines an I2C slave interface, a programmable prescaler, a 12-bit counter for each channel, and per-channel ON/OFF latches. Outputs are totem-pole CMOS so they can pull low (sink) or high (source) 25 mA, allowing direct drive of LED anodes through a current-limiting resistor. The OE input forces all outputs into a high-impedance state for hardware blanking during camera flashes or system reset. Typical applications include LCD TV/monitor backlight panels, RGB/RGBA status indicators, multi-channel servo or motor control via PWM, gaming peripherals with LED feedback, and architectural accent lighting strips. The wide 2.3 V to 5.5 V supply range and up to 1 MHz Fm+ I2C also suit low-power portable and battery-backed designs. When designing with this part, place a 0.1 uF decoupling capacitor close to VDD and route SDA/SCL away from switching traces. For >8 MHz PWM prescalers, ensure the external 50 MHz reference (if used) provides < 2% jitter to maintain frequency accuracy, and bias unused LEDn outputs low or leave floating per datasheet guidance. This page synthesizes distributor pricing, drop-in alternatives from the PCA9685 family, and practical design notes not found in the standalone datasheet, giving engineers a complete component decision package for I2C-LED designs.
PCA9685PW,118 - 16-Ch 12-bit PWM LED Driver I2C | NXP
The NXP PCA9685PW,118 is a 16-channel, 12-bit PWM LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting applications, delivering up to 25 mA per channel via an I2C-bus interface at speeds up to 1 MHz. Housed in a 28-pin TSSOP package, it integrates 16 individually programmable PWM outputs with 4096-step resolution (0% to 100% duty cycle) and supports a total of 62 addressable devices on a single bus through 6 hardware-selectable I2C address pins. An LED driver IC is a specialized power-management device that translates low-power digital control signals into high-current outputs suitable for driving light-emitting diodes. Within the broader taxonomy, the PCA9685PW,118 belongs to the LED driver family, which itself is a sub-category of display drivers and power management ICs. LED drivers serve a critical role in modern electronics by providing constant-current regulation, PWM dimming, and bus-addressable control for everything from single status indicators to multi-channel RGB lighting arrays used in signage, automotive interiors, and consumer appliances. Key features of the PCA9685PW,118 include a 1 MHz Fast-Mode Plus (Fm+) capable I2C interface, programmable push-pull or open-drain output stages, and a 40 ns transition time optimized for high-color-depth RGBA mixing. The device operates from 2.3 V to 5.5 V supply voltage, draws 10 mA typical quiescent current, and supports both LED dimming and digital servo control on the same pins. An external 25 MHz crystal is not required - an internal oscillator accepts a single resistor-timed reference. The TSSOP-28 package provides compact board integration suitable for handheld and embedded designs. The PCA9685PW,118 is engineered around a 16-channel constant-current sink architecture with per-channel 12-bit PWM counters clocked from an internal 25 MHz oscillator. Each output provides a totem-pole driver capable of either sinking current to ground or sourcing current from V+ (software configurable), enabling direct driving of common-anode or common-cathode LED strings. The device supports cascaded operation by allowing up to 62 nodes on one I2C bus, with selectable base addresses set by external pull-ups on six address pins, making it ideal for matrix panels and large lighting arrays. Typical applications include LCD TV and monitor backlight control, RGBW architectural lighting strips, servo motor control in robotics, and automotive interior ambient lighting. The 1 MHz I2C capability enables fast refresh rates across all 16 channels, suitable for color-mixing animations on large displays. When designing with the PCA9685PW,118, ensure that the per-channel current does not exceed 25 mA and that total package dissipation stays below the thermal limit of the TSSOP-28 (theta_JA approximately 80 C/W). Adding small 0.1 uF ceramic decoupling capacitors near VDD and V+ pins is recommended for noise immunity.
PCA9685PW-Q900118 - 16-Channel 12-bit I2C LED Controller | NXP
The NXP PCA9685PW-Q900118 is a 16-channel, 12-bit PWM Fm+ I2C-bus LED controller optimized for Red/Green/Blue/Amber (RGBA) color backlighting, housed in a 28-pin TSSOP package. Each of the 16 LED outputs has an individual 12-bit (4096-step) PWM controller operating at a programmable frequency from 24 Hz to 1526 Hz, with duty cycle adjustable from 0% to 100%. The device supports a 1 MHz fast-mode-plus I2C interface and offers 25 mA per-channel sink current with software-adjustable group brightness and blink control. The PCA9685 belongs to the LED driver IC category, a sub-class of display drivers within the broader power management and optoelectronics hierarchy. As an I2C-controlled PWM generator, the PCA9685 differs from constant-current LED drivers because each output is an open-drain transistor capable of switching a higher voltage rail than the 2.3V-5.5V VDD supply, making it suitable for driving external MOSFETs, servo motors, and high-voltage LED strings with appropriate pull-ups. Key features include six programmable I2C slave addresses (allowing up to 62 PCA9685s on a single bus for 992 PWM channels total), a 25 MHz internal oscillator with no external timing components required, an active-low OE output enable pin for hardware synchronization, and software-reset (SWRST) software register. The integrated 12-bit PWM provides fine-grained dimming resolution of 0.024% per step at full-scale output. Each output supports continuous current sinking up to 25 mA and peak current to 100 mA during switching transitions. Architecturally, the PCA9685 uses a programmable 8-bit prescaler feeding a 12-bit counter for each output channel, allowing all 16 channels to be phase-aligned or operated independently. The device operates from 2.3V to 5.5V VDD and can switch LED loads up to 5.5V on the LED supply rail (V+), separating logic power from LED power for efficiency optimization. The I2C interface supports standard-mode (100 kHz), fast-mode (400 kHz), and fast-mode-plus (1 MHz), with built-in hardware address pins allowing six chip selects per bus segment. Typical applications include LCD TV and monitor RGBA backlight control, desktop and notebook keyboard backlighting, RGB LED status indicator arrays, hobby servo motor control via PCA9685-based breakout boards, and decorative LED strip dimming. The programmable output frequency from 24 Hz to 1526 Hz covers both flicker-free visible-light applications and acoustic-servo control use cases that benefit from higher update rates above 50 Hz. When designing with the PCA9685, decouple VDD with a 1uF to 10uF ceramic capacitor placed close to pin 28, and provide a separate bulk capacitor on the V+ LED supply rail. Add 100k pull-up resistors on SDA, SCL, and OE for reliable I2C communications, and consider in-rush current on multi-channel designs because switching all 16 outputs simultaneously can stress the V+ rail. The TSSOP-28 footprint is hand-solderable with care but is best assembled in production via reflow to avoid bridging the 0.65 mm pitch leads. This page synthesizes distributor pricing, drop-in same-package alternatives (commercial- and automotive-grade Q900 suffix variants and base PCA9685PW,118), and practical design notes not found in the NXP datasheet alone.
STP16CP05TTR - 16-Ch 100mA LED Sink Driver | STMicroelectronics
The STMicroelectronics STP16CP05TTR is a monolithic, low-voltage, 16-bit constant-current LED sink driver housed in a 24-pin TSSOP (Tape & Reel) package. It integrates a 16-bit serial-in, parallel-out shift register feeding a 16-bit D-type storage register, with sixteen regulated current sources on the output stage capable of delivering 5 mA to 100 mA per channel. Operating from a 3.0 V to 5.5 V logic supply and tolerating up to 20 V on the output rails, the device is engineered to drive LED panel displays with uniform brightness and minimal external component count. A constant-current LED driver is a specialized display driver IC that delivers a precisely regulated DC current to each LED in an array, eliminating the brightness mismatch that occurs when LEDs are driven by simple ballast resistors. The STP16CP05TTR belongs to the broader family of LED display drivers, which sit within the power management and display driver IC category of semiconductors. By sinking a programmable constant current from each LED cathode, the part shifts the thermal and aging variation from individual LEDs onto a single, well-controlled silicon reference, ensuring consistent luminance across the entire panel. Key features include a 30 MHz serial clock interface, 16 equal-current output channels, an external resistor-programmable output current up to 100 mA per channel, a 20 V output voltage rating, and a thermal shutdown protection circuit. The shift register and storage register architecture allows simultaneous update of all 16 outputs, eliminating the visual artifacts caused by sequential refresh. An output enable pin (active-low) supports blanking and PWM dimming, while the serial data path is cascadable to drive larger LED arrays by daisy-chaining multiple STP16CP05 devices. The internal architecture uses matched bipolar current mirrors with a single external reference resistor (REXT) setting the global current. All 16 outputs share the same reference, so channel-to-channel matching typically tracks within +/-1 percent at the same output voltage. The output stage sustains up to 20 V per channel, which allows driving long strings of series LEDs from a single high-voltage rail while the logic section operates from a low-voltage MCU-compatible supply. Typical applications include indoor LED video panels, full-color RGB dot-matrix displays, message boards, signage backlights, and decorative lighting controllers. The cascadable serial interface lets designers expand channel count without additional GPIO, and the wide 5 mA to 100 mA programmable range covers both indicator LEDs and high-brightness panel pixels from a single BOM. When designing with the STP16CP05TTR, place the REXT resistor close to the REXT pin and use a 0.1 uF decoupling capacitor on VDD. For PWM dimming, drive the OE pin from a timer channel rather than bit-banging, and ensure the LED supply common-anode rail is referenced to the same ground as the logic supply to avoid logic-level errors during high-current transients. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet, giving engineers a single reference for sourcing and implementing the STP16CP05TTR.
TLD1211SJFUMA1 - 85mA Linear LED Driver, 28V max | Infineon
The Infineon TLD1211SJFUMA1 is an integrated adjustable constant-current LED driver IC fabricated in bipolar technology, delivering up to 85 mA to a single output stage with PWM dimming capability in an 8-pin PG-DSO-8-16 surface-mount package. It is part of the LITIX Linear family designed for severe automotive lighting environments, providing constant LED brightness over the full automotive supply range. A linear LED driver is a regulator topology that places a power device in series with the LED string, dropping excess supply voltage as heat while precisely regulating the current flowing through the LED load. Unlike switching LED drivers, linear drivers introduce no EMI and no switching ripple, simplifying PCB layout for noise-sensitive environments such as rear combination lamps and interior ambient lighting. Key features include a wide supply operating range of 5.5 V to 28 V (load-dump tolerant to 40 V), an external sense resistor that programs output current from a few mA up to 85 mA, integrated PWM dimming via the EN pin (accepting CMOS/TTL levels), and protection circuitry against over-temperature, over-current, and reverse polarity conditions typical of automotive 12V/24V bus systems. The TLD1211SJ uses a bipolar transistor process combined with a precision bandgap reference to set the sense voltage across the external resistor. Its low headroom requirement (typical Vsense around 0.5 V to 1.3 V at low current) minimizes wasted power while keeping the LED current tightly regulated across temperature and supply variations. Typical applications include automotive tail/brake lighting, turn indicators, daytime running lights (DRL), and interior LED strings where PWM dimming is required. The single-channel architecture suits single-LED or short-string loads where high efficiency is unnecessary but EMI-free operation and small PCB footprint matter. When designing with this part, ensure the PCB dissipates the (VIN - VLED) x IOUT heat via copper pour. Use a 1 percent or better external sense resistor (typically 13 ohm for 65 mA) for stable current matching across the automotive temperature range. This page synthesizes distributor pricing, drop-in alternatives, and practical automotive design notes not found in the Infineon datasheet alone, helping engineers select and validate the TLD1211SJFUMA1 against modern automotive LED lighting requirements.